Cisco Prime Infrastructure 2.0 add antenna?

Hi!,
I Have installed a cisco infrastructure 2.0 application. during the configuration phase of the heatmaps I notice that my antenna model is not in the list; there is a "generic antenna" option but this antenna is a "directional" antenna but my model is AIR-ANT2430V-R an omni-directional antenna. how can i ADD my exact model of antenna to the Prime Infrastructure app?

Just to be more specific, i need to know if is possible add more antennas on this option marked on the picture... this is to avoid use the "other" option or other equivalent model (which is what i have configured now based on the dBi value)... thanks in advance for any idea...

Similar Messages

Cannot add WLC 5508 7.2.111.3 to Cisco Prime Infrastructure 2.0

Though the Cisco Prime Infrastructure Compatibility Matrix list out that 7.2.111.3 is supported for PI 2.0
I am not able to add the controller to the PI 2.0.
The Reachability Status always shown "Unknow" and SNMP Status always shown "No response for SNMP Get".
There is no firewall between the WLC and PI.
And ping test shows it is reachable.
If I try to add controller by non-management port (I know it is not work but I want to try the reachability), the Reachability Status shown "Reachable" but the SNMP Status always shown error.
And if I use some SNMP testing software to test the SNMP port. SNMP can be quoted.
I have try to lower down the "Maximum VarBinds per Get PDU" but no luck.
Any thing I can do to troubleshoot the problem?

Yes, I follow the procedure but it does not work.
Another update:
I add another WLC with version 7.0.98.0. It is fine.
And I setup another new PI 2.0 and new temporary WLC5508 with 7.2.111.3 to test. It work fine also......
So, I am wondering the existing 7.2 WLC have problem in responsing the SNMP Get. But I dont have any idea to test....
Do anyone have idea to test the snmp connection between PI and WLC?

Cisco Prime Infrastructure 2.2 Rest API XML does not add LF

I am using several scripts that dig the data from XML files created through Cisco Prime Infrastructure Rest API. It worked fine until 2.1. Now, with 2.2, seems Cisco stopped adding LF to each line and everything is 'one' line.
Here is an example with 2.1, there is a LF to the end of each line:
?xml version="1.0" encoding="UTF-8" standalone="yes"?>
<queryResponse type="AccessPointDetails" rootUrl="https://server/webacs/api/v1/data" requestUrl="https://server/webacs/api/v1/data/AccessPointDetails?type=contains(UnifiedAp)&.full=true&.maxResults=1000&.firstResult=0" responseType="listEntityInstances" count="715" first="0" last="714">
    <entity url="https://server/webacs/api/v1/data/AccessPointDetails/1505569" type="AccessPointDetails" dtoType="accessPointDetailsDTO">
        <accessPointDetailsDTO id="1505569" displayName="1505569">
            <adminStatus>ENABLE</adminStatus>
            <apType>AP1240</apType>
            <cdpNeighbors>
                <cdpNeighbor>
                    <capabilities>Switch IGMP </capabilities>
                    <duplex>Half Duplex</duplex>
                    <interfaceSpeed>100Mbps</interfaceSpeed>
                    <localPort>2</localPort>
                    <neighborIpAddress>10.1.1.1</neighborIpAddress>
                    <neighborName>switch</neighborName>
                    <neighborPort>FastEthernet0/1</neighborPort>
                    <platform>cisco WS-C3560-8PC</platform>
                </cdpNeighbor>
Now, with 2.2, there is not LF anywhere:
?xml version="1.0" encoding="UTF-8" standalone="yes"?><queryResponse type="AccessPointDetails" rootUrl="https://server/webacs/api/v1/data" requestUrl="https://server/webacs/api/v1/data/AccessPointDetails?type=contains(UnifiedAp&.full=true&.maxResults=1000&.firstResult=0" responseType="listEntityInstances" count="715" first="0" last="714">
<entity url="https://server/webacs/api/v1/data/AccessPointDetails/1505569" type="AccessPointDetails" dtoType="accessPointDetailsDTO">
<accessPointDetailsDTO id="1505569" displayName="1505569"><adminStatus>ENABLE</adminStatus><apType>AP1240</apType><cdpNeighbors><cdpNeighbor>
Does anyone know, is this intentional or a mistake? Or is there a way how I control this?
I am reading on-line CPI Rest API docs, but seems cannot find anything.
Thanks,
Vlad

PI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks

When is Cisco Prime Infrastructure 2.0 released, and what does 2.0 offer?

We are running Prime Infrastructure 1.3 primarily for wireless management at this point. We have enough licenses to add all our switches, routers, and firewalls, but we're hesitant to do so until 2.0 comes out. While there are some features for backing up and configuring switches and routers, 1.3 still seems pretty limited in regards to non-wireless features. For example, nearly every report in 1.3 is for wireless controllers or AP's, there are no reports I've found relevent for switches and routers. I've read a lot of blogs, cisco posts, and white papers talking about how Cisco Prime Infrastrucure 2.0 will finally consolidate Prime into a truly all-in-one network management suite that can manage the entire Cisco environment. Does anyone know when it's officially being released? Does anyone have an tech sheets on what's new in 2.0, or what its capabilities are? I want to better understand what 2.0 has to offer, when it's coming out, how to upgrade, so I can start planning for the upgrade and eventually importing all our network devices to Cisco Prime for centralized management. Any useful information or links would be appreciated.
Thanks,
Christian

PI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks

Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
    0 Bad SNMP version errors
    14 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    38453185 Number of requested variables
    0 Number of altered variables
    17790703 Get-request PDUs
    20583581 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    38371069 Response PDUs
    13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
Jeremy

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Ciscoworks LMS 3.0 to Cisco Prime Infrastructure LMS 4.2

In order to complete the upgrade the LMS 3.x runs over a physical server that ends with the upgrade(server its gona be retired), the think is that the Cisco Prime comes with an UCS and its gona run over a VM. The question here is the "Cisco Prime Infrastructure 1.1 - Maj Upg from LMS 2.x/3.x" media could be runs as clean install, I mean with no LMS 3.x intalled before? an the "Prime Infrastructure LMS 4.2 - 1.5K Device Maj Upg Lic" could be registered with no license installed of LMS 3.x?

There are a couple of things to distinguish:
1. The product SKU you need to order to migrate from LMS 3 to LMS 4.2.
2. The license file that is installed on that new LMS server.
#1 is based on Cisco agreeing, usually through the partner or reseller you are working with, that you are entitled to order the upgrade SKU (vs. buy a complete new product). The upgrade SKUs are all listed in the ordering guide here.
L-PI12-1.5K-UP (note - NOT the 1.1 product description you noted in the original post) would be the SKU for a major upgrade from LMS 2.x/3.x to the current Prime Infrastructure 1.2 release at the 1500 device license level. That upgrade includes licenses for both PI 1.2 and Prime LMS 4.2. You may choose which to install - most LMS customers stick with LMS for now as PI 1.2 does not yet have full feature parity. Your managed devices should not exceed 1500 combined (in this case) but that combined number is not enforced technically by the product's license daemon.
Once you have purchased the product and have the media you can install it on any host that meets the installation prerequisites as far as OS, memory, disk etc. A clean installation of LMS does not check for or require a previous installation as far as technical checks.
#2 - Once you have installed the new LMS server (and optionally a step near the end of installation, you need to add in the license file (*.lic file). That is obtained through the Cisco licensing portal (or via the TAC if you prefer) using the Product Activation Key (PAK) received with your product.

UPS monitoring support with Cisco Prime Infrastructure 1.2

Dear Members,
Good day,
I am having a project implemented wherein i have the UPS power redudancy solution for our network devices.
Now can anyone gide that is it possible for below :-
UPS units installed with SNMP cards be monitored via Cisco Prime Infrastructure 1.2 as our monitoring & management solution is Cisco Prime Infrastructure 1.2 ?
if yes
Can you guide if following action would be possible to export the below logs from UPS unit to our Cisco Prime Infrastructure 1.2
   a) UPS fault status information
   b) UPS operational status(input power available Y/N)
   c) Battery fault status
   d) Battery charging current
   e) Battery charge level
   f) Output current
Conclusion is we need to confirm that would it be posible to achieve remote monitoring of these UPS units via our CPI 1.2
Thanks in Advance for your support & replies to this query.
Regards,
Muzammil N.

Prime Infrastructure 1.2 can manage non-Cisco devices in a limited fashion via SNMP query and trap processing. It cannot import logs and does not have a generic syslog server,
So if your devices have snmp read only support and can generate SNMP traps for the above you can add them to PI. Follow the manual add device procedure here.

Cisco Prime Infrastructure patch 2.1.1 - HA issue

Hello,
I have a problem with the Cisco Prime Infrastructure patched to version 2.1.1. I did exactly what Installation Guidelines say:
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-1-1/release/notes/cpi_rn.html
– Install the Prime Infrastructure 2.1.1 patch by using the Administration > Software Updates page on the primary server.
– Restart the primary server.
– Verify that the patch installation is complete. If you find the installation complete, decommission and reinstall the secondary server and add it back to the primary server.
I reinstalled HA server and I'm trying to add it to HA but I get "Failed to authenticate - Primary(xx.xx.xx.xx) and Secondary(xx.xx.xx.xy) PI version does not match"
Can you help me with that? What I'm doing wrong? or maybe this patch is not prepared to work in HA mode?
Regards

Symptom:
The installation instructions of PI 2.1.1 patch in a High Availability environment are not accurate and following these steps will result in the inability to re-pair the Primary and Secondary servers.
Conditions:
If the instructions are followed, then when the user attempts to re-pair the servers, an error will be encountered:
"High Availability Registration Failed - Failed to authenticate - Primary (x.x.x.1) and Secondary (x.x.x.2) PI version does not match".
Instead, the following steps have proved to work correctly:
1. Upload and install patch on primary.
2. Upload and install patch on secondary.
3. Stop NCS services on secondary
4. Stop NCS services on primary
5. Start services on secondary
6. Start services on primary
7. Re-pair HA servers from primary
Workaround:
Workaround 1:
On the secondary, go under root and issue:
# cd /opt/CSCOlumos/bin/
# ./hamode.sh primary
Answer 'yes' when prompted.
Go to admin user and execute
# ncs stop
After the services are stopped:
# ncs start
When the services are back up, login to the secondary GUI as you would login to a primary server
Go under Administration > Software update, upload the patch and install it.
Go to admin user and execute
# ncs stop
After the services are stopped:
# ncs start
When the services are up, go under root and issue:
# cd /opt/CSCOlumos/bin/
# ./hamode.sh secondary
Answer 'yes' when prompted.
Go to admin user and execute
# ncs stop
After the services are stopped:
# ncs start
After the message that services started successfully on the secondary, initiate a new High Availability configuration from the primary. Now the synchronization between the two servers should succeed.
Workaround 2:
Redeploy or reinstall the Primary server, restore the backup which was taken prior to applying the patch, reconfigure the High Availability and continue with the steps described in the Conditions section.
Further Problem Description:
Release Notes have been updated with more precise instructions.
Known Affected Releases:
(1)
2.1(0.0.85)

Cisco Prime Infrastructure MESH LINK ISSUE

Hi,
a Customer of us has a trouble with cisco Prime Infrastructure 1.2.0.12 and AP mesh link.
There is an huge database ( i suppose the issue can be here ) and when we display some map ( each floor has about 6 RAP and 24 MAP ) we cannot see the MESH information and link draw.
The only way to dipley them is to disable "refresh from network": this way I'm able to show these link..... until a click before.
What i noticied when all was working fine, after i click to some floor:
1) the software started to show the map with normal color and no mesh info displayed ( just ap and coverage cloud )
2) after few time ( less than 1 second ) the map was becoming a little bit lighter and the mesh info was merged to the map
We are missini the second step
Anyone had the same issue ?
best regards
Luigi
PS: I opened a case with WCS version 6.0 ( same issue ) but, after some months, no risult. The last version working fine was WCS 5.2

Just to add some more informations:
- disabling "refreshj from network" ( building properties ) the link and mesh info are showed
- while I'm on a floor, after some refresh, i loose the mesh link draw and, if i click on an AP, i loose also mesh info in the popup. It' s like, after some refresh, the AP are no more recognized as Mesh ( !?!? )
regards
Luigi

Cisco Prime Infrastructure 1.2 with SNMPv3

Dears,
I am trying to add a router on Cisco Prime Infrastructure 1.2 using snmpv3 (authpriv, sha & aes256). When i go to device work center and add a device, i cannot find the AES-256 in the privacy options. Only None, DES, and AES-128 are available.
Is there any workarround?
Please advise.
Moustafa

PI only supports SNMP privacy up through AES-128 at this time. Reference the guide section on adding an new SNMP credential entry.
Additionally there is a bug with SNMP v3 support in PI 1.2. It should be resolved in PI 1.3.

Cisco Prime Infrastructure 1.2 - web browser freezes when managing rogue APs alarms

Hello all,
has anybody faced a freezing problem when you click in Cisco Prime Infrastructure 1.2 down on alarm bar and then to Rogue AP alarms and then try to add an annotitation or change a rogue alarm to Friendly?
I tried it on different PC, different browsers (Firefox 14.0.1. Chrome ...) and the problem is still there.
Has anybody an idea?
Thanks.
Regards
Karel

I just tried it from my lab VM and had no problems. I use Chrome and the browser does sometimes not refresh for a while but that is just when I start to click around.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Cisco Prime Infrastructure 2.0 Alarms (switch port down)

We have a cisco Prime Infrastructure 2.0 managing switches, routers and AP.
By default, when a port of a switch goes down, the cisco Prime Infrastructre generates a Critical Alarm for that. (this is a problem, because every phone of laptop disconnection will generate a critical alarm for me)
I found out that if we go to Administration --> Alarm Severity --> Link down, I can change the Alarm from Critical to another type of alarm.(ex: warning)
The problem is that I want to keep the Critical Alarm for my Uplinks ports and for some important switch ports, and I would like to make the alarm as warning for the normal user ports.
I know that I can create Port Groupping and add ports to each group and apply monitoring templates on those groups. But This couldn't Help me solving my alarm problem.
So I just need to know how to manage the alarms severity for each group of ports.
Thank you

Hi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work?

Cisco nexus 6001 not a supported device on cisco prime infrastructure 2.1?

I have installed Cisco Prime Infrastructure 2.2 and Prime Infrastructure still doesn't seem to support the Nexus 6001 platform? Can someone tell me if Cisco Prime Infrastructure will ever support the Cisco Nexus 6001 platform or is there any plans to support it in any future device packs?

The Nexus 6001 isn't currently supported in PI 2.1. There's no workaround except to wait for a device or product update that adds support. Right now I know the 9000 series is on the 2.2 roadmap but I haven't seen any reference to the 6001 and PI.
Interestingly, Prime LMS does support both the 6001 and 6004. Reference.

WLC 2504 in Cisco Prime Infrastructure 1.2

Trying to add Cisco 2504 Wireless Controller, Software Version 7.3.101.0, to Cisco Prime Infrastructure
1.2 (1.2.0.103), License Evaluation, with no success.
When using Discovery, Discovery Job show Credential Errors: "Error occured due to invalid SNMP credential"
When Add Device from Device Work Center I get:
Reachability is "Unknown", Device Type is empty, Collection Status is "Managed with Warnings", with message "SNMP Failure: No Response for SNMP Get request.", Collection Time is empty.
I've tried with both snmp v2 and v3.
I've tried to lower "Maximum VarBinds per Get PDU" to 10 or 20, cause I've read similar problem in NCS.

I solved the same problem 5min ago.!
select the device and press syc ..that helped me ...

Cisco Prime Infrastructure Compatibility

Hi
I have been informed by our supplier that i cannot add-
Nexus switches
Routers
Into the switches list in Cisco Prime Infrastructure Version 2.0
However we seem to have one Fabric SVI 'Managed and Sychronized'
So i dont know whether i should or should not be able to add 7ks
and 5ks to the switch list
Anyone any ideas on this -- the official line seems to be no... if thats true then how did we
get the one 7l on and managed
Steve

You mention a fabric SVI. Note that the FabricPath and other data center-specific technology features are for the most part not managed by PI. Prime DCNM is the tool for that.
You can use PI to manange 7ks and 5k's as standard switches - backup their configs, poll them with SNMP queries, collect syslog messages etc.

Cisco Prime Infrastructure 2.0 add antenna?

Similar Messages

Maybe you are looking for