Cisco Prime infrastructure 2.0 cpu requirement
Hi,
i'm reading the doc at http://www.cisco.com/en/US/customer/docs/net_mgmt/prime/infrastructure/2.0/quickstart/guide/cpi_qsg.html#wp46865
and I'm searching for the CPU requirement for a Standard installation. From table 2 in this document, I will need 16 virtual CPUS but there is no frequency mentioned. Does someone know what is the minimum CPU frequency to run PI 2.0 correctly?
Thanks
Theo
The number of vCPU's depends on your ESXi host, either your limited to 8 or you will have 16, 32, etc. The vCPU amount is defined on the VM or PI2.0 and you can change it after the VM has been installed. PI 2.0 has an Express (4 vCPU), Standard and Pro which require 16 vCPU. There is a custome express that uses the Express ova (4 vCPU), but you need to increase that to 8 vCPU. Hope that helps.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
Similar Messages
-
Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?
Prime Infrastructure/ Assurance is positioned today more towards managing network elements and network performance, rather than server infrastructure. We are in the process of adding Datacenter component support, with more focus on Nexus and UCS- due later this year.
Having said that, Prime Infrastructure allows the system user to add custom SNMP polling templates, which can then be used for polling any SNMP based values from any SNMP enabled device. These can be used to collect the information you specified below and the polled information will be available in dashboards and reports. -
Cisco Prime Infrastructure 1.x Server requirements & Operating System
Dear Friends
I wish you are in very good health ........ I really very confused regarding LMS and i really needs your help ........ I need to order LMS for one of our customer with 500 devices and reporting cabailities ..... So i chosse base license "R-PI-1.1-K9" and 500 device license "R-PI-1.1-500-K9" and
Compliance Management - 500 Device License "L-PI-1.1-CM-500"
What really confused me that i tried to search server cabalitity for my requirments & Operating system and couldn't find it ...... what i need your help for is the following:
1) What is the server requirments ???
2) What is operating system (windows 2008 or VMWare VMware ESX/ESXi Version 4.1 or 5.0)
3) Is their any deticated applicance from Cisco ??
Please help
Thanks in advanceIn addition to the release notes for the 4.2.3 patch noted above, please also see the 4.2 release notes which further direct you:
Server and Client Requirements
For information on server and client requirements for the system and browser, see Chapter 2 of Installing and Migrating to Cisco Prime LAN Management Solution 4.2 at:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/install/guide/
install.html
To summarize the options it describes, you can run the LMS product on any number of platforms - a dedicated Cisco hardware appliance, a physical server of your own with Windows or Solaris OS, a VMware server with a Windows server OS guest, or a "soft appliance". The soft appliance is package built with the underlying guest OS (a customized RHEL distribution with Cisco's Application Development Environment OS (ADE-OS)) built-in.
Once you have installed LMS 4.2, you should patch - first to 4.2.2 and then to the current 4,2,3. then run the software update feature to bring all package components up to date.
Regarding licensing, there is a Cisco Prime Infrastructure Ordering and Licensing Guide here.
When you order the licenses for PI 1.2 (new customer), you order the base product and then Lifecycle licenses (required for either PI 1.2 Lifecycle and LMS installations - which option is a customer choice) and, optionally, Compliance and Assurance licenses. An upgrade order for an existing LMS customer will include the base PI 1.2 with Lifecycle licenses as well as LMS in a single SKU as noted in tables 4 and 5 of the Ordering Guide. -
Hi,
I have a Cisco Prime Infrastructure 1.3 deployment with Catalyst 2960S switches. Switches are running IOS 15.0(2) SE2. All switches have SNMPv2 configured, and all appears to be fine. I'm migrating one switch to SNMPv3, and PI have reachability to the switch, but PI doesn´t receive traps from the switch, and neither poll CPU and memory information (all displays 0.00%).
Somebody have a sample configuration of SNMPv3 with Cisco Prime (Infrastructure or LMS)? I cannot find a Cisco official (or unofficial) document related to this version, usually all mention SNMPv2.
Thank you.
EduardoHi Eduardo:
SNMPv3 is indeed supported for general administration. There's a bug with SWIM using SNMPv3 (CSCud92758), but you should be fine for just monitoring. Have you deleted the switch, waited until Prime Infrastructure told you it was gone, then readded it as SNMPv3 natively? Bug CSCug78869 keeps things from working well when changing SNMP versions.
If you don't have the new Update-1 patch for Prime Infrastructure 1.3.0.20 installed (filename PI_1.3.0.20_Update_1-12.tar.gz) installed, I'd suggest you get it. While it's not going to specifically address this issue, there are a lot of really good fixes in it.
Release Notes for Update 1 for Cisco Prime Infrastructure 1.3.0.20 -
Cisco prime infrastructure 1.3 makes every 15 minutes cpu high on cisco 800 routers
I have an issue with cisco prime infrastructure 1.3 and cisco 880 routers, every 15 minutes the cpu goes to 100% on those routers, but I cannot find the job on the prime which is causing this, if I look in the job dashboard I have some jobs like sam_poller_22_15_getvpnpoller_27977292 that runs every 15 minutes (other jobs that I see CDBPoller_dmvpnPoller and CDBPoller_getvpnpoller) , probably is it on of these jobs, but how can I stop it (job type : poller job, owner =system) and what are they doing?
thanks for any assistanceThis is what i expected. I know many platform like 29xx/39xx or ISR's has known issues with Cisco Prime Infrastructure when it polls CISCO-LICENSE-MGMT-MIB, devices go high on CPU.
You have to block clmgmtLicenseInfoEntry by creating a view on your 800 router by configuring snmp view.
Following is the command/example:
Step 1: Configure SNMP View:
snmp-server view iso included
snmp-server view clmgmtLicenseInfoEntry excluded
Link community string to SNMP View:
snmp-server community view ro|rw
Example per your configuration:
snmp-server view PrimeInfra iso included
snmp-server view PrimeInfra clmgmtLicenseInfoEntry excluded
snmp-server community ArgSnmp view PrimeInfra RO ACLSNMP_RO
OR you can try following on your Cisco PI:
Manually update file below,
Open the /opt/CSCOlumos/conf/sam/template.xml, modify the template id=20 (licensePoller)
Update tag for value 600 to 86400 for all attrributes () of
template id =20
Old: 600
New: 86400
Some known bugs on such issues are :
CSCug97914 and CSCuc72024
Please check and let me know the updates.
-Thanks
Vinod
**Rating Encourages contributors, and its really free. ** -
Cisco Prime Infrastructure 2.0 and Cisco ASA
Hello,
We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
ASA version is 5505, image is 9.1(2).
So, I have a question: is it possible to manage ASAs with PI 2.0?
UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.Have you downloaded and applied the latest Device Pack updates?
PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location. -
Cisco Prime Infrastructure 1.2 on Windows Server/Hyper-V
Hi Everyone,
In Entriprise environment while designing a BYOD solution we need to integrate ISE3315 with CPI 1.2. I know that Cisco ISE software either runs on 3315 platform or other option is virtual appliance (which is VMware based). Now problem is that we have Hyper-V environment as standard so I need to go with ISE-3315. Here my concern is to I install CPI 1.2 on Hyper-V, or on a Windows Server (2008 or 2012) based machine. Is that doable?
Any help, suggessions would be warmly welcomed.
Thanks,
Azhar...Cisco Prime LMS will slowly be phased out in favor of Cisco Prime Infrastructure and hence there are no new mainline releases are planned to provide support to new Hardware or virtualization support.
However, Prime LMS do support Hyper V Virtualization (As an installable in Windows 2008). Please note that Virtualization technologies like, VMWare and Hyper V virtualization systems are not supported in LMS 5000, and LMS 10000 Devices license, in Windows. VMWare Systems are supported in LMS 5000, and LMS 10000 Devices license in Soft Appliance. Virtualization technologies like, VMWare and Hyper V virtualization systems are not supported in LMS 5000, and LMS 10000 Devices license, in Windows. VMWare Systems are supported in LMS 5000, and LMS 10000 Devices license in Soft Appliance.
For more details on HW and SW requirements for Cisco Prime LMS, please check document here.
-Thanks
Vinod -
Ciscoworks LMS 3.0 to Cisco Prime Infrastructure LMS 4.2
In order to complete the upgrade the LMS 3.x runs over a physical server that ends with the upgrade(server its gona be retired), the think is that the Cisco Prime comes with an UCS and its gona run over a VM. The question here is the "Cisco Prime Infrastructure 1.1 - Maj Upg from LMS 2.x/3.x" media could be runs as clean install, I mean with no LMS 3.x intalled before? an the "Prime Infrastructure LMS 4.2 - 1.5K Device Maj Upg Lic" could be registered with no license installed of LMS 3.x?
There are a couple of things to distinguish:
1. The product SKU you need to order to migrate from LMS 3 to LMS 4.2.
2. The license file that is installed on that new LMS server.
#1 is based on Cisco agreeing, usually through the partner or reseller you are working with, that you are entitled to order the upgrade SKU (vs. buy a complete new product). The upgrade SKUs are all listed in the ordering guide here.
L-PI12-1.5K-UP (note - NOT the 1.1 product description you noted in the original post) would be the SKU for a major upgrade from LMS 2.x/3.x to the current Prime Infrastructure 1.2 release at the 1500 device license level. That upgrade includes licenses for both PI 1.2 and Prime LMS 4.2. You may choose which to install - most LMS customers stick with LMS for now as PI 1.2 does not yet have full feature parity. Your managed devices should not exceed 1500 combined (in this case) but that combined number is not enforced technically by the product's license daemon.
Once you have purchased the product and have the media you can install it on any host that meets the installation prerequisites as far as OS, memory, disk etc. A clean installation of LMS does not check for or require a previous installation as far as technical checks.
#2 - Once you have installed the new LMS server (and optionally a step near the end of installation, you need to add in the license file (*.lic file). That is obtained through the Cisco licensing portal (or via the TAC if you prefer) using the Product Activation Key (PAK) received with your product. -
Ask the Expert: Cisco Prime Infrastructure - Implementation and Deployment
Welcome to the Cisco Support Community Ask the Expert conversation.
This Ask The expert Session will cover questions spanning Cisco Prime Infrastructure on Implementation and Deployment on Wired and Wireless. This will be more specific to Customer’s and Partners questions product covering PI on configuration, Features and Menu, Network Monitoring, Maps, Implementation, High Availability and Maintenance and t/s parts.
Monday, February 2nd, 2015 to Friday, February 13th, 2015
Dhiresh Yadav is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco Prime Infrastructure and Cisco Wireless products. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS) and CCIE (DC) certifications.
Afroz Ahmad is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS),CCIE (DC), and SCJP (Sun Certified Java Professional )
Vinod Kumar Arya is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 8 years of industry experience working with large enterprise and service provider networks. He also holds VCP 5 and RHCE certifications.
** Remember to use the rating system to let the experts know you have received an adequate response.**
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure community, > Network Management, shortly after the event. This event lasts through February 13th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.Hello Wilson,
Thanks for joining us.
1841 should just work fine for net flow . Hope you have a valid "PI Assurance license" installed on the server.
"PI Assurance license" is required for "net-flow" feature
Devices supporting Netflow in PI ::
1400, 1600, 1700 & 1800
2500, 2600 & 2800
3600, 3700, 3750 & 3800
4500 & 4700
AS5300 & 5800
7200, 7300, 7400 & 7500
Catalyst 4500 ASCI
Catalyst 5000, 6500, & 7600 ASCI
ESR 10000 ASCI
GSR 12000 ASCI
Cisco IOS Software Release Version
Supported Cisco Hardware Platforms
11.1CA, 11.1CC
Cisco 7200 and 7500 series, RSP 7200 series
12.0
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series
12.0T, 12.0S
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8600 series
12.0(3)T, 12.0(3)S
Cisco 1720, 2600, 3600, 4500, 4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)T
Cisco 1400, 1600, 1720, 2500, 2600, 3600, 4500,
4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)XE
Cisco 7100 series
12.0(6)S
Cisco 12000 series
NetFlow is also supported by these devices Cisco 800, 1700, 1800, 2800, 3800, 6500, 7300, 7600, 10000, CRS-1 and these Catalyst series switches: 45xx, 55xx, 6xxx.
NetFlow export is also supported on other Cisco switches when using a NetFlow Feature Card (NFFC) or NFFC II and the Route Switch Module (RSM), or Route Switch Feature Card (RSFC). However, check whether version 5 is supported, as most switches export version 7 by default.
You can check the below steps to diagnose the issue::
To verify that NetFlow is exported from a device to PI, follow the steps below:
1) Browse to Administration > Data Sources page. Check the value in column ‘Last Active Time’ for the ‘Device Data Sources’ table. If the table is empty or the value does not represent recent time, then
it is possible that the device is not exporting NetFlow or PI Assurance license is not applied / expired.
2) Login to PI console ( via SSH) as root user and run the command:
netstat –an | grep 9991 – Output of this should be like : udp 0 0 :::9991 :::*
Check the firewall settings on PI server using the command: firewall -L
1) Check the configuration on an IOS / IOS –XE device. Run the commands
a) sh running-config | inc destination
1) This should list the IP address of the PI SERVER ( along with other outputs if any)
b) sh running-config | inc 9991
1) This should list at least one entry.
c) If the above are fine, then verify that the flow monitor, flow exporter and the flow records are correctly configured on the device.
Refer to the URLs below to configure NetFlow export.
http://preview.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_monitor.html#wp1056427
Thanks-
Afroz
***Ratings Encourages Contributors **** -
Monitoring ASA in Cisco Prime infrastructure 2.2
Hi everybody. I have some issue with cisco Prime Infrastructure 2.2. We use this product in our network for monitoring network devices and I need to monitor also our ASA 5550 device with soft 8.4. I added ASA to Cisco PI but see only basic component like my device can reachable via and read via snmp. But cannot see CPU, RAM, Device ENV like Temperature, l2l vpn connection, Interfaces status and Utilization that interfaces, cannot see sub interface that placed on ASA like that g0/0.20. I need fully monitor ASA and See logs and trap for my device:
CPU RAM ENV (Temperature), Interface and sub interface status, L2L VPN Status.
1 Cisco Prime infrastructure can full support ASA for monitoring and logging.. IF YES how can i configure that features in Cisco PI 2.2 for ASA
2 IF not which product Can full support that features for full monitoring and logging ASA devices
I have a little deadline for finishing
thanks everybody beforeI've not success monitoring ASA interface utilization either. I'm using PI 2.2 with device update #1. The ASA is a 5585-X with 9.2(3) software.
I have deployed the PI monitoring template to the ASA and do see its overall status and PI has enumerated the interfaces in the device page.
I even looked at a packet capture and see PI querying the values of the interface counters and those values being sent back to PI - yet I cannot select any ASA interface when drilling down under Performance Detail monitoring.
When I get some free time I will open a TAC case on it, meanwhile I am getting all the info I need from the upstream and downstream switches. -
Cisco Prime Infrastructure 1.2 licensing
I have a customer that is running CiscoWorks 3.2 and they also have NCS 1.1 (upgraded from WCS 7.0). They have found that it costs way more to upgrade CiscoWorks to Cisco Prime Infrastructure than it would be to just buy licenses after they finish upgrading NCS to Cisco Prime 1.2.
The main question about Cisco Prime 1.2 is how the licensing works, we need to know if the licensing will work the same as it did for CiscoWorks where they only needed one license for a full stack of switches. They believe that Prime 1.2 will require a license for each switch in the stack, which will cause them to buy several more licenses than what they feel they can afford.
If anyone knows how the licensing works, it would be appreciated.
Thanks.Have you gone through the below link
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/guide_c07-714720.html -
Cisco Prime Infrastructure 1.2 - Remote FTPrepository Sizing Guide
Can anyone provide a link to a sizing guide for remote FTP repository for backing up Cisco Prime Infrastructure 1.2 to a remote FTP server?
A personal observation; In PI 1.1, with the small ova we were running around 300 AP's and I had noticable slowness and issues. At that time, TAC mentioned that I should go with the medium as it was a known problem Now, despite being on 1.2 and alot of the issues resolved (and now new ones), if faced with the need to start over and I could spare the hardware, I would still go with the medium. My personal opinion is that Cisco VM's require way to much. On the other hand, knowing that it's relying on a built in Oracle DB, which from my experience with virtual servers, databases in VM = bad, it's understandable. Not everyone agrees with this point from vm gurus to db geniuses, and I'm not a professional vm guy, just play one on tv, but personally i shove as much hardware as I can afford from my host at it if it's a db in a vm. This comes from being in an enterprise with multiple oracle db's in multiple vm environments. My 2cents.
-
WCS and LMS to Cisco Prime Infrastructure 1.3 Upgrade
Hello,
Our customer is currently having WCS for 500 devices and LMS 3.2 for 1500 devices. We are planning to upgrade to Cisco Prime Infrastructure 1.3.
I want to check is the upgrade procedure that we have planned is ok or we have missed something.
Phase 1: WCS to CPI 1.3 upgrade
1. Check that WCS is at 7.0.230.0 version
2. Export WCS database
3. Install NCS 1.1.1.24 software
4. Contact cisco to obtain trial license for NCS software (L-WCS-NCS1-M-K9 license).
5. Migrate WCS license and import it in NCS software
6. Migrate WCS data to NCS software using ncs migrate command
7. Patch NCS software
8. Inline upgrade to CPI 1.3 software
9. Install proper licenses on CPI 1.3 (WCS and LMS device count)
My concern in this first phase is should I use NCS large image since our Cisco Prime Infrastructure 1.3 software should manage 2000 devices at the end.
Or is it better not to perform inline upgrade and insted go with exporting data from NCS and then importing them to CPI 1.3 that is going to be installed separately?
Phase 2: LMS 3.2 to CPI upgrade
1. Export LMS 3.2 database
2. Install LMS 4.2 software
3. Install license to LMS 4.2
4. Restore data from LMS 3.2 to LMS 4.2
5. Direct upgrade from LMS 4.2 to 4.2.2
6. Export the device list with credentials from LMS 4.2.2 and import it as a Bulk Import in CPI 1.3
At the end we will have CPI 1.3 and LMS 4.2.2 software running.
Is it possible to directly upgrade from LMS 4.2 to LMS 4.2.4 and then import data to CPI 1.3 or we need to go with 4.2.2 version?
Regards,
JelenaHello Marvin,
We have restored LMS 3.2 SP 1 database on LMs 4.2 and we have got some error messages during restore. Please see our restore output:
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/res
resolver.pl restoreDBTableMig.pl restoreJRMMig.pl restorebackup.pl
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/restorebackup.pl -d /opt/BKP/
Restore started at : 2013/12/05 14:11:58
Please see '/var/adm/CSCOpx/log/restorebackup.log' for status.
USER ID is ..................................... : sysadmin
OS of the backup archive is..................... : Windows
INFO:The backup archive is from a different OS. Your current Platform is: Soft Appliance .
You are attempting to perform a Cross Platform Restore..
Do you wish to continue (Y/N) [Y] :Y
Generation to be restored is ................... : 0
Backup taken from............................... : /opt/BKP/
Common Services version in the backup data is... : 3.3.1
Common Services is installed in................. : /opt/CSCOpx
The temp folder for this restore program........ : /opt/CSCOpx/tempBackupData
Applications installed on this machine ......... : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][cwportal][ipm][upm][cvw][cwlms]
Applications in the backup archive ............. : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][opsxml][cwportal][ipm][upm][cvw]
WARNING: The list of applications installed on this CiscoWorks server does not match the list of
applications in the backup archive. If you restore data from this backup archive,it may
cause problems in the CiscoWorks applications.
Do you want to continue the restore operation? (y-continue or n-quit, y/n)?Y
Applications to be restored are................. : [Common Services] [Campus Manager] [Resource Manager Essentials] [Device Fault Manager] [cwportal] [ipm] [upm] [cvw]
Available disk space in NMSROOT................. : 86451488 Kb
Required disk space in NMSROOT.................. : 35906524 Kb
(The temp and NMSROOT are on same device, therefore this required disk space includes temp space)
Copying the backup files to the temporary location [/opt/CSCOpx/tempBackupData]
preRestore of [Common Services] has started.
preRestore of [Common Services] has completed.
preRestore of [Campus Manager] has started.
preRestore of [Campus Manager] has completed.
preRestore of [Resource Manager Essentials] has started.
preRestore of [Resource Manager Essentials] has completed.
preRestore of [Device Fault Manager] has started.
preRestore of [Device Fault Manager] has completed.
preRestore of [cwportal] has started.
preRestore of [cwportal] has completed.
preRestore of [ipm] has started.
preRestore of [ipm] has completed.
preRestore of [upm] has started.
preRestore of [upm] has completed.
preRestore of [cvw] has started.
preRestore of [cvw] has completed.
doRestore of [Common Services] has started.
Cross Platform Update started.
Cross Platform Update completed.
License check started.
WARNING: The license details in the server are different from the backup data.
After restoring, please check the license available in the server.
WARNING: Your current license count is lower than your earlier license count.
If you restore the data now, devices that exceed the current licence count
will be moved to Suspended state.
License check completed.
Restoring certificate.
WARNING: Cannot evaluate the hostname, hence the certificate
may be from this host or another host.
[ Certificate not overwritten ]
Restored Certificate.
Restoring Common Services database.
Restored Common Services database.
Restoring CMIC data.
Restored CMIC data.
Restoring CMC data.
Restored CMC data.
Restoring Security Settings.
Restored Security Settings.
Restoring DCR data.
Restored DCR data.
Restoring Certificate key store.
Restored Certificate key store.
Restoring DCNM CrossLaunch data.
Restored DCNM CrossLaunch function.
Restoring JAAS configuration.
Restored JAAS configuration.
JRM Job Migration started.
JRM job Migration done.
doRestore of [Common Services] has completed.
doRestore of [Campus Manager] has started.
Cross Platform Migration for Campus started.
Cross Platform update Starts for Campus
doRestore of [Campus Manager] has completed.
doRestore of [Resource Manager Essentials] has started.
10% of RME Restore completed
30% of RME Restore completed
50% of RME Restore completed
70% of RME Restore completed
100% of RME Restore completed
doRestore of [Resource Manager Essentials] has completed.
doRestore of [Device Fault Manager] has started.
10% of DFM Restore completed
30% of DFM Restore completed
50% of DFM Restore completed
80% of DFM Restore completed
Going to modify Eight PM report
Modified Sucessfully Eight PM report
100% of DFM Restore completed
doRestore of [Device Fault Manager] has completed.
doRestore of [cwportal] has started.
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.script ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.log ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultUserCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
doRestore of [cwportal] has completed.
doRestore of [ipm] has started.
10% of IPM Restore Completed
30% of IPM Restore Completed
50% of IPM Restore Completed
60% of IPM Restore Completed
70% of IPM Restore Completed
100% of IPM Restore Completed
doRestore of [ipm] has completed.
doRestore of [upm] has started.
HUM database restore starts
INFO:STOP= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
SQL Anywhere Command File Hiding Utility Version 10.0.1.4239
INFO: Database Shutdown is in Progress..Please wait
INFO: Stop Engine Args= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
INFO: After Database Shutdown RC= 2304
root=C:\PROGRA~2\CSCOpx\databases\upm\upm.db
DBUTILS: Inside Cross Platform
INFO: Current Database password does not match the password of Database being restored
INFO: Using the Password of the Database being restored
HUM database restore successfully completed.
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate/README.txt
Directory is reportsStarted changing property .
linux
Restored HUM configuration file successfully.
doRestore of [upm] has completed.
doRestore of [cvw] has started.
doRestore of [cvw] has completed.
postRestore of [Common Services] has started.
postRestore of [Common Services] has completed.
postRestore of [Campus Manager] has started.
postRestore of [Campus Manager] has completed.
postRestore of [Resource Manager Essentials] has started.
postRestore of [Resource Manager Essentials] has completed.
postRestore of [Device Fault Manager] has started.
postRestore of [Device Fault Manager] has completed.
postRestore of [cwportal] has started.
postRestore of [cwportal] has completed.
postRestore of [ipm] has started.
postRestore of [ipm] has completed.
postRestore of [upm] has started.
postRestore of [upm] has completed.
postRestore of [cvw] has started.
postRestore of [cvw] has completed.
Restored successfully.
Are this errors going to affect our LMS 4.2 operations?
Then we have upgraded to LMS 4.2.2 and exported data and credentiales for PI import.
On PI 1.3 we have installed WCS 500 devices upgrade license and LMS 1500 upgrade license and now we are having 2000 devices lifecycle license. We have successfully restored WCS data in PI and we have imported LMS devices as bulk import. What is strange is that we have this message in prime regarding licensing:
On LMS 3.2 our customer had saved unlimited number of configuration versioning. After upgrading to LMS 4.2 we can only see last 3 configurations regardless of unlimided number of configurations in previous LMS, so my question is where can we find older configurations in LMS 4.2?
We are planning to turn unlimited versioning on CPI 1.3 now, so our customer will again have feature that they need. Do you have some experiance regarding disk space when all device configurations are stored forever?
Thank you for your help.
Regards,
Jelena -
Problem with implementing license in Cisco Prime Infrastructure 2.2
Goodday,
For Cisco Prime Infrastructure 2.2 I downloaded an license from the license portal.
This concerns a eval/demo license, for an demo of Cisco Prime Infrastructure 2.2.
When selecting the the type of license you get a few options, from which I selected the basic, advanced and lifecycle evaluation licenses. This is the type of license that is required for our demo.
After completing the wizard I can download en implement the license.
Until this point everything goes as it supposed to be.
When i go to the Prime Infrastructure 2.2 appliance (running on VMWare ESXi 5.5.0).
When I go to the license section in Cisco Prime Infrastructure I can implement the license, however if I implement the .lic file I get the error “Unknown feature (PI_VM)”.
I have done implementing license files before, but this is the first time i encounterd this problem.
Who can help me with this error?
Regards,
Dennie VerhoevenHi Dennie,
PI2X-BASE-LF-AS-US-VM-N-EVAL-90 >> I think you have used this product name while generating the license
Either you try generating a new license or contact cisco license team to generate a new license
with the information like below ::
Product Name : R-PI2X-K9
Product Description : R-PI2X-K9:R-PI2X-K9 : Cisco Prime Infrastructure 2.x
Product Qty : 1
UDI : PID: PRIME-NCS-VAPL SN: ANY:ANY
Serial no : with ANY:ANY will work as starting from PI 2.2 , there is no node locking with license.
Thanks-
Afroz
****Ratings Encourages Contributors **** -
Cisco Prime Infrastructure, Express, licensing
Are there any funcionatility limitation between each edition of the Cisco Prime Infrastructure other than supported number of devices?
Does it support turning APs on and off on a predefined scheduled?
I read in the manual "Cisco Prime Infrastructure Classic View Configuration Guide for Wireless Devices" that it is possible to Managing WLAN Status Schedules. Does it require the assurance license feature set or will lifecycle license will be sufficient?I believe you could create a scheduled Lightweight AP Configuration Template job and have it simply turn off the radios on the selected APs. Make it recurring (every night at a certain time) and add a complementary recurring job to turn the radios back on at the desired time.
See the following screeenshot from PI 2.0 (click to enlarge):
Maybe you are looking for
-
Hello, You have been first contacted by DATALOGICS (adobe ID [email protected]). As you need to contact us, I send this post because we would to find a solution for this problem. To resume, we are contacting us about a problem with search functionnal
-
My appointments changed from 11:00 to 10:00, how can this be?
hi guys, I have an problem with my Iphone 3gs. What happened is that the time changed from summertime (DST) to wintertime, but so did my appointments. So when I got a appointment at 11:00, now it says; 10:00. This is not what I had in mind. Can someb
-
No internet connection in Safari or iTunes after 10.4.0.80 update
iTunes updated Safari to 5.34.50.0 with last update. After that, I have no internet connection in Safari web browser, iTunes Store or iTunes Help, or iTunes Remote. Firefox, Internet Explorer, and Chrome all work fine. I'm running Windows XP Home E
-
Permisions to read and write on a external hard drive
Currently I am working with two Mac Air. One of them with Mac OS X 10.9.5 and the other one with Mac OS10.7.5. Also I have most of my files in an external hard drive. When I try to move file from the Mac air with Mac OS10.7.5 to the hard drive, I hav
-
When I try to compile anything with #include <ctype>, g++ says it's not available. I tried running it through Xcode as well as opposed to the shell to no avail. Xcode actually marks it as an error in the editor. I just upgraded to OS X 10.8 and Xcode