Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
    0 Bad SNMP version errors
    14 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    38453185 Number of requested variables
    0 Number of altered variables
    17790703 Get-request PDUs
    20583581 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    38371069 Response PDUs
    13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
Jeremy

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Similar Messages

Cisco Prime Infrastructure 1.4 SNMP Traps are not converted into Alarms

Hi everybody,
I just configured SNMP Traps on a Cisco Catalyst 3750-x to send to our Cisco Prime Infrastructure 1.4 Appliance.
Now I forced the Switch to send some traps (Power off a Power Supply, Interface errdisable). The only events I see in Alarms & Events on PI is the same information message everytime:
Configuration management event has been recorded in ccmHistoryEventTable.
I think the forced traps should be converted into alarms? Why can't I see them?
Thanks,
Marc

Ok, I started debugging as you said. I get the following output:
Mar 13 09:28:13.711: SNMP: V2 Trap, reqid 11689, errstat 0, erridx 0
sysUpTime.0 = 198609846
snmpTrapOID.0 = ciscoSyslogMIB.2.0.1
clogHistoryEntry.2.1688 = PM
clogHistoryEntry.3.1688 = 5
clogHistoryEntry.4.1688 = ERR_RECOVER
clogHistoryEntry.5.1688 = Attempting to recover from bpduguard err-disable state on Gi1/0/13
clogHistoryEntry.6.1688 = 198609844
Mar 13 09:28:13.737: SNMP: Queuing packet to xx.xx.xx.xx
Looks like the Switch is sending SNMP Traps from the ciscoSyslogMIB. Is this why PI can't show the Traps and convert it into a alarm?
After this test I configured logging (syslog) to the PI. Now the errors are showed but still not converted into alarms. I just want to be notified by email when such errors occurs.
Thanks,
Marc

Cisco prime infrastructure 2.2

Hello Team,
I did like to know how i can create a baseline template using Cisco prime infrastructure 2.2 in order to compare configuration of devices.
Also I would like to inquire how I can generate a CLI template and view the CLI template before applying/deploying it to a particular device or devices.
Best Regards,
Tioluwani

Having just started with Prime not that long ago, I'm afraid I can't help with your first question. However, for your second question:
Go to Configuration > Templates > Features and Technologies
Along the left menu, expand CLI Templates and click on CLI
This will bring up a new, blank CLI template to the right of the menu
Just fill out the info at the top section, and input your CLI/Velocity code in the bottom section
Once you have the code like you want it, click the "Save as New Template" button at the bottom
A window will pop-up asking where you want to save it within the "My Templates" folder
Once you've selected a location, click the Save button
Your window will automatically refresh to show the newly created custom CLI template - you will now have the option to edit your template as needed, or deploy it as-is to PI devices.
To deploy the template, select the Deploy button along the bottom
A new window will pop up that allows you to prepare and schedule the template. Select the device or devices you wish to deploy to. The devices you have available to deploy to will be based on the Validation Criteria you entered when creating the template.
If you opted to use the awesome variables available to CLI templates, you can either enter those for all selected devices in the Value Assignment section, or you can fill out the variables on a per-device basis. You will skip this section if you did not define any variables. If you did use variables, you must click the Apply button at the bottom of this section after you fill in the variables, or you will receive the following error:Mandatory fields are not entered for some devices or you have not saved your changes. To save the changes, click on Apply.
In the Schedule section, you can select when the template is deployed - "Now" is the default.
Finally, the Job Option section allows you to select how Prime handles a deployment failure, whether you want Prime to save the config to startup after the deployment, and whether you want to initiate a config archive after the deployment.

Cisco prime infrastructure 2.0 inventory SFP

hello,
anyone knows if it is possible with cisco prime infrastructure 2.0 create inventory to obtain data from SFP (serial number and model)?
thank you

Hi ,
Can you try the below report and see if you are able to see the information , you are looking for
Report > Report Launch Pad > Device > Detailed Hardware
Thanks-
Afroz
***Ratings Encourages Contributors ****

Cisco Prime Infrastructure 1.3 - SNMPv3 can´t get CPU, memory info.

Hi,
I have a Cisco Prime Infrastructure 1.3 deployment with Catalyst 2960S switches. Switches are running IOS 15.0(2) SE2. All switches have SNMPv2 configured, and all appears to be fine. I'm migrating one switch to SNMPv3, and PI have reachability to the switch, but PI doesn´t receive traps from the switch, and neither poll CPU and memory information (all displays 0.00%).
Somebody have a sample configuration of SNMPv3 with Cisco Prime (Infrastructure or LMS)? I cannot find a Cisco official (or unofficial) document related to this version, usually all mention SNMPv2.
Thank you.
Eduardo

Hi Eduardo:
SNMPv3 is indeed supported for general administration. There's a bug with SWIM using SNMPv3 (CSCud92758), but you should be fine for just monitoring. Have you deleted the switch, waited until Prime Infrastructure told you it was gone, then readded it as SNMPv3 natively? Bug CSCug78869 keeps things from working well when changing SNMP versions.
If you don't have the new Update-1 patch for Prime Infrastructure 1.3.0.20 installed (filename PI_1.3.0.20_Update_1-12.tar.gz) installed, I'd suggest you get it. While it's not going to specifically address this issue, there are a lot of really good fixes in it.
Release Notes for Update 1 for Cisco Prime Infrastructure 1.3.0.20

Monitoring ASA in Cisco Prime infrastructure 2.2

Hi everybody. I have some issue with cisco Prime Infrastructure 2.2. We use this product in our network for monitoring network devices and I need to monitor also our ASA 5550 device with soft 8.4. I added ASA to Cisco PI but see only basic component like my device can reachable via and read via snmp. But cannot see CPU, RAM, Device ENV like Temperature, l2l vpn connection, Interfaces status and Utilization that interfaces, cannot see sub interface that placed on ASA like that g0/0.20. I need fully monitor ASA and See logs and trap for my device:
CPU RAM ENV (Temperature), Interface and sub interface status, L2L VPN Status.
1 Cisco Prime infrastructure can full support ASA for monitoring and logging.. IF YES how can i configure that features in Cisco PI 2.2 for ASA
2 IF not which product Can full support that features for full monitoring and logging ASA devices
I have a little deadline for finishing
thanks everybody before

I've not success monitoring ASA interface utilization either. I'm using PI 2.2 with device update #1. The ASA is a 5585-X with 9.2(3) software.
I have deployed the PI monitoring template to the ASA and do see its overall status and PI has enumerated the interfaces in the device page.
I even looked at a packet capture and see PI querying the values of the interface counters and those values being sent back to PI - yet I cannot select any ASA interface when drilling down under Performance Detail monitoring.
When I get some free time I will open a TAC case on it, meanwhile I am getting all the info I need from the upstream and downstream switches.

Cisco Prime Infrastructure 2.0 - Third Party NetFlow

Hi,
is it possible to collect on the Cisco Prime Infrastructure 2.0 NetFlows from Third Party Devices, like a SonicWALL Firewall?
I mean it is possible to poll SNMP informations from a third party device, so maybe it is also possible to get the NetFlow from this Device?
Best Regards,
Sven K.
Sent from Cisco Technical Support iPad App

Hi Sven,
As per my understanding for 3rd party Only below thing are supported:
The following support level is available with Prime Infrastructure :
• Auto Discovery of a 3rd party Device
• Basic Inventory collection
• Basic lifecycle management of 3rd party device
• Ability to show traps and syslog for 3rd party devices
• Device reachability status polling
• Ability to load new MIBs & to create new monitoring templates
• For both Cisco and any SNMP device
More info is available in the link given below:
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.2/release/notes/cpi_rn.html#wp75765
Thanks-
Afroz
[Do rate the useful post]

Can't import images in cisco prime infrastructure 1.2

- Any job , trying to import images, in my cisco prime infrastructure fails with :
Jan 14 13:14:53 cisco-prime 01/14/13 13:15:18.040 ERROR [service] [pool-4-thread-19] IFM_SWIM_EXCEPTION: [com.cisco.ifm.swim.service.exception.IfmSwimParserException: Cannot populate software image info object from the image.]
How I can I solve this one ?
Tx,
M.

I seem to have the same problem, strangely enough importing a universal image for 2960s worked fine, but I get thos error when trying to import a 3750x image

UPS monitoring support with Cisco Prime Infrastructure 1.2

Dear Members,
Good day,
I am having a project implemented wherein i have the UPS power redudancy solution for our network devices.
Now can anyone gide that is it possible for below :-
UPS units installed with SNMP cards be monitored via Cisco Prime Infrastructure 1.2 as our monitoring & management solution is Cisco Prime Infrastructure 1.2 ?
if yes
Can you guide if following action would be possible to export the below logs from UPS unit to our Cisco Prime Infrastructure 1.2
   a) UPS fault status information
   b) UPS operational status(input power available Y/N)
   c) Battery fault status
   d) Battery charging current
   e) Battery charge level
   f) Output current
Conclusion is we need to confirm that would it be posible to achieve remote monitoring of these UPS units via our CPI 1.2
Thanks in Advance for your support & replies to this query.
Regards,
Muzammil N.

Prime Infrastructure 1.2 can manage non-Cisco devices in a limited fashion via SNMP query and trap processing. It cannot import logs and does not have a generic syslog server,
So if your devices have snmp read only support and can generate SNMP traps for the above you can add them to PI. Follow the manual add device procedure here.

Cisco Prime Infrastructure MESH LINK ISSUE

Hi,
a Customer of us has a trouble with cisco Prime Infrastructure 1.2.0.12 and AP mesh link.
There is an huge database ( i suppose the issue can be here ) and when we display some map ( each floor has about 6 RAP and 24 MAP ) we cannot see the MESH information and link draw.
The only way to dipley them is to disable "refresh from network": this way I'm able to show these link..... until a click before.
What i noticied when all was working fine, after i click to some floor:
1) the software started to show the map with normal color and no mesh info displayed ( just ap and coverage cloud )
2) after few time ( less than 1 second ) the map was becoming a little bit lighter and the mesh info was merged to the map
We are missini the second step
Anyone had the same issue ?
best regards
Luigi
PS: I opened a case with WCS version 6.0 ( same issue ) but, after some months, no risult. The last version working fine was WCS 5.2

Just to add some more informations:
- disabling "refreshj from network" ( building properties ) the link and mesh info are showed
- while I'm on a floor, after some refresh, i loose the mesh link draw and, if i click on an AP, i loose also mesh info in the popup. It' s like, after some refresh, the AP are no more recognized as Mesh ( !?!? )
regards
Luigi

Cisco Prime Infrastructure 2.1 Express OVA failing to boot up

Hi all, i'm wondering if you can help me, i'm trying to deploy Cisco Prime Infrastructure in a lab envrionment but it's not working correctly.
I've deployed "PI-VA-2.1.0.0.87-Express.ova" to a VMware ESXI 5.1U2 hypervisor with 2x AMD 8128HE CPUs, 96GB RAM, ASUS KGPE-D16 motherboard. The installation works fine, I can answer all the questions and enter the IP address. Once the system reboots, it hangs at the following screen:
"Kernel direct mapping tables up to 340000000 @ 10000-1c000" is the last thing I see
Interestingly at this point I can actually ping the VM... I cant connect to the managemnet console on HTTPS though :(
I did find some related info on a blog https://deekayen.net/kernel-alive-lock which mentions booting with "noapic", however when I try to press "P" on the grub boot loader it prompts me to enter a password which I dont know! My normal admin passwords arent working.
Any help to ge tthis running would be greatly appreciated
Thanks in advance
Ben

The server takes about 30 mins to boot up, it's not actually broken it's just extremely slow .. I have found numerous people reporting this issue online, and our production system also does this! I guess my original problem is solved, although I would prefer this issue not to exist!

WCS and LMS to Cisco Prime Infrastructure 1.3 Upgrade

Hello,
Our customer is currently having WCS for 500 devices and LMS 3.2 for 1500 devices. We are planning to upgrade to Cisco Prime Infrastructure 1.3.
I want to check is the upgrade procedure that we have planned is ok or we have missed something.
Phase 1: WCS to CPI 1.3 upgrade
1. Check that WCS is at 7.0.230.0 version
2. Export WCS database
3. Install NCS 1.1.1.24 software
4. Contact cisco to obtain trial license for NCS software (L-WCS-NCS1-M-K9 license).
5. Migrate WCS license and import it in NCS software
6. Migrate WCS data to NCS software using ncs migrate command
7. Patch NCS software
8. Inline upgrade to CPI 1.3 software
9. Install proper licenses on CPI 1.3 (WCS and LMS device count)
My concern in this first phase is should I use NCS large image since our Cisco Prime Infrastructure 1.3 software should manage 2000 devices at the end.
Or is it better not to perform inline upgrade and insted go with exporting data from NCS and then importing them to CPI 1.3 that is going to be installed separately?
Phase 2: LMS 3.2 to CPI upgrade
1. Export LMS 3.2 database
2. Install LMS 4.2 software
3. Install license to LMS 4.2
4. Restore data from LMS 3.2 to LMS 4.2
5. Direct upgrade from LMS 4.2 to 4.2.2
6. Export the device list with credentials from LMS 4.2.2 and import it as a Bulk Import in CPI 1.3
At the end we will have CPI 1.3 and LMS 4.2.2 software running.
Is it possible to directly upgrade from LMS 4.2 to LMS 4.2.4 and then import data to CPI 1.3 or we need to go with 4.2.2 version?
Regards,
Jelena

Hello Marvin,
We have restored LMS 3.2 SP 1 database on LMs 4.2 and we have got some error messages during restore. Please see our restore output:
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/res
resolver.pl           restoreDBTableMig.pl restoreJRMMig.pl      restorebackup.pl
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/restorebackup.pl -d /opt/BKP/
Restore started at : 2013/12/05 14:11:58
Please see '/var/adm/CSCOpx/log/restorebackup.log' for status.
     USER ID is ..................................... : sysadmin
     OS of the backup archive is..................... : Windows
INFO:The backup archive is from a different OS. Your current Platform is: Soft Appliance .
You are attempting to perform a Cross Platform Restore..
Do you wish to continue (Y/N) [Y] :Y
     Generation to be restored is ................... : 0
     Backup taken from............................... : /opt/BKP/
     Common Services version in the backup data is... : 3.3.1
     Common Services is installed in................. : /opt/CSCOpx
     The temp folder for this restore program........ : /opt/CSCOpx/tempBackupData
     Applications installed on this machine ......... : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][cwportal][ipm][upm][cvw][cwlms]
     Applications in the backup archive ............. : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][opsxml][cwportal][ipm][upm][cvw]
     WARNING: The list of applications installed on this CiscoWorks server does not match the list of
              applications in the backup archive. If you restore data from this backup archive,it may
              cause problems in the CiscoWorks applications.
              Do you want to continue the restore operation? (y-continue or n-quit, y/n)?Y
     Applications to be restored are................. : [Common Services] [Campus Manager] [Resource Manager Essentials] [Device Fault Manager] [cwportal] [ipm] [upm] [cvw]
     Available disk space in NMSROOT................. : 86451488 Kb
     Required disk space in NMSROOT.................. : 35906524 Kb
     (The temp and NMSROOT are on same device, therefore this required disk space includes temp space)
Copying the backup files to the temporary location [/opt/CSCOpx/tempBackupData]
preRestore of [Common Services] has started.
preRestore of [Common Services] has completed.
preRestore of [Campus Manager] has started.
preRestore of [Campus Manager] has completed.
preRestore of [Resource Manager Essentials] has started.
preRestore of [Resource Manager Essentials] has completed.
preRestore of [Device Fault Manager] has started.
preRestore of [Device Fault Manager] has completed.
preRestore of [cwportal] has started.
preRestore of [cwportal] has completed.
preRestore of [ipm] has started.
preRestore of [ipm] has completed.
preRestore of [upm] has started.
preRestore of [upm] has completed.
preRestore of [cvw] has started.
preRestore of [cvw] has completed.
doRestore of [Common Services] has started.
          Cross Platform Update started.
          Cross Platform Update completed.
          License check started.
             WARNING: The license details in the server are different from the backup data.
                      After restoring, please check the license available in the server.
             WARNING: Your current license count is lower than your earlier license count.
                      If you restore the data now, devices that exceed the current licence count
                      will be moved to Suspended state.
          License check completed.
          Restoring certificate.
             WARNING: Cannot evaluate the hostname, hence the certificate
                      may be from this host or another host.
                      [ Certificate not overwritten ]
          Restored Certificate.
          Restoring Common Services database.
          Restored Common Services database.
          Restoring CMIC data.
          Restored CMIC data.
          Restoring CMC data.
          Restored CMC data.
          Restoring Security Settings.
          Restored Security Settings.
          Restoring DCR data.
          Restored DCR data.
          Restoring Certificate key store.
          Restored Certificate key store.
Restoring DCNM CrossLaunch data.
          Restored DCNM CrossLaunch function.
          Restoring JAAS configuration.
          Restored JAAS configuration.
          JRM Job Migration started.
          JRM job Migration done.
doRestore of [Common Services] has completed.
doRestore of [Campus Manager] has started.
          Cross Platform Migration for Campus started.
Cross Platform update Starts for Campus
doRestore of [Campus Manager] has completed.
doRestore of [Resource Manager Essentials] has started.
10% of RME Restore completed
30% of RME Restore completed
50% of RME Restore completed
70% of RME Restore completed
100% of RME Restore completed
doRestore of [Resource Manager Essentials] has completed.
doRestore of [Device Fault Manager] has started.
10% of DFM Restore completed
30% of DFM Restore completed
50% of DFM Restore completed
80% of DFM Restore completed
Going to modify Eight PM report
Modified Sucessfully Eight PM report
100% of DFM Restore completed
doRestore of [Device Fault Manager] has completed.
doRestore of [cwportal] has started.
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.script ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.log ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultUserCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
doRestore of [cwportal] has completed.
doRestore of [ipm] has started.
        10% of IPM Restore Completed
        30% of IPM Restore Completed
        50% of IPM Restore Completed
        60% of IPM Restore Completed
        70% of IPM Restore Completed
        100% of IPM Restore Completed
doRestore of [ipm] has completed.
doRestore of [upm] has started.
HUM database restore starts
INFO:STOP= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
SQL Anywhere Command File Hiding Utility Version 10.0.1.4239
INFO: Database Shutdown is in Progress..Please wait
INFO: Stop Engine Args= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
INFO: After Database Shutdown RC= 2304
root=C:\PROGRA~2\CSCOpx\databases\upm\upm.db
DBUTILS: Inside Cross Platform
INFO: Current Database password does not match the password of Database being restored
INFO: Using the Password of the Database being restored
HUM database restore successfully completed.
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate/README.txt
Directory is reportsStarted changing property .
linux
Restored HUM configuration file successfully.
doRestore of [upm] has completed.
doRestore of [cvw] has started.
doRestore of [cvw] has completed.
postRestore of [Common Services] has started.
postRestore of [Common Services] has completed.
postRestore of [Campus Manager] has started.
postRestore of [Campus Manager] has completed.
postRestore of [Resource Manager Essentials] has started.
postRestore of [Resource Manager Essentials] has completed.
postRestore of [Device Fault Manager] has started.
postRestore of [Device Fault Manager] has completed.
postRestore of [cwportal] has started.
postRestore of [cwportal] has completed.
postRestore of [ipm] has started.
postRestore of [ipm] has completed.
postRestore of [upm] has started.
postRestore of [upm] has completed.
postRestore of [cvw] has started.
postRestore of [cvw] has completed.
Restored successfully.
Are this errors going to affect our LMS 4.2 operations?
Then we have upgraded to LMS 4.2.2 and exported data and credentiales for PI import.
On PI 1.3 we have installed WCS 500 devices upgrade license and LMS 1500 upgrade license and now we are having 2000 devices lifecycle license. We have successfully restored WCS data in PI and we have imported LMS devices as bulk import. What is strange is that we have this message in prime regarding licensing:
On LMS 3.2 our customer had saved unlimited number of configuration versioning. After upgrading to LMS 4.2 we can only see last 3 configurations regardless of unlimided number of configurations in previous LMS, so my question is where can we find older configurations in LMS 4.2?
We are planning to turn unlimited versioning on CPI 1.3 now, so our customer will again have feature that they need. Do you have some experiance regarding disk space when all device configurations are stored forever?
Thank you for your help.
Regards,
Jelena

Cisco Prime Infrastructure 1.2 Error

Hi,
I don't have any experience with Cisco Prime infrastructure. I am getting the below error
Unable to start secondary NCS server PRLPrimeNCS02 [10.140.xx.xx]
Reason: IO Error: could not resolve the connect identifier "wcss1"
Not sure exactly what the error means. Any help much appreciated.
Thanks
Nachi

Hi Scott,
Thank you for your email.
The HA is runing on the Cisco Prime. Runing Cisco Prime on a Virtual machine in VM.
The issue we are experiencing is that the system failed over to the secondary (HA) for unknown reasons. When we failed it back it didn’t fail back properly. Configured Manual failover. Managed to failback to primary but it complained HA was no longer configured.
Tried to remove HA and reconfigure it. The primary removed the HA configuration, but the secondary kept it. Here is some info on the secondary
PRLPrimeNCS02/admin# ncs ha status
[Server] prlprimencs01(10.xx.xx.xxx) [State] Secondary Lost Primary [Failover Type] manual
PRLPrimeNCS02/admin# ncs ha remove
High availability configuration will be removed
Do you wish to continue? (y/N) y
Removing secondary configuration will remove all database information
Do you wish to remove high availability configuration from primary? (y/N) y
Secondary is attempting to remove high availability configuration from both primary and secondary
Requesting primary to remove high availability configuration from both primary and secondary
Successfully removed high availability configuration
PRLPrimeNCS02/admin#
PRLPrimeNCS02/admin#
PRLPrimeNCS02/admin# ncs ha status
[Server] prlprimencs01(10.xx.xx.xxx) [State] Secondary Lost Primary [Failover Type] manual
PRLPrimeNCS02/admin#
And the primary
prlprimencs01/admin# ncs ha status
[State] Stand Alone
prlprimencs01/admin#
Below is the log
Starting Health Monitor as a secondary
Checking for Port 8082 availability... OK
truststore used is /opt/CSCOlumos/conf/truststore
truststore used is /opt/CSCOlumos/conf/truststore
Starting Health Montior Web Server...
Health Monitor Web Server Started.
Starting Health Monitor Server...
Health Monitor Server Started.
java.lang.OutOfMemoryError: Java heap space
Dumping heap to logs/java_pid6044.hprof ...
Heap dump file created [249907589 bytes in 6.857 secs]
Thanks
Nachi

Including Interface Description in Cisco PRime Infrastructure Alarm Message

Hi all,
i succesfully configured a Cisco Prime Infrastructure 2.1 applliance to display an alarm and to send me an e-mail when switch uplink ports goes down.
The text displayed in alarm message is :
port 'interface_id' is down on device 'device_ip_address'
I'd like to include in this text also the interface description so the text will display :
port 'interface_id' 'interface_descriprion' is down on device 'device_ip_address'
Is this possible?
Thankyou in advance

Hi,
i followed these steps :
SWITCH SIDE
- configured Prime Infrastructure as snmp-server host;
- enabled snmp-traps for linkup and linkdown events globally;
- disabled snmp-traps for linkup and linkdown on non relevant interfaces using the no snmp trap link-status command
PRIME INFRASTRUCTURE SIDE
- under "Deploy/Monitor Deployment" i deployed template "Interface Health" for all the interested switches
- under "Administration/System Settings/Mail Server Configuration" configured my internal SMTP server to make Prime Infrastructure able to send e-mails
- under "Operate/Alarms & Events" click on "Email Notifications" , then on "Switches and Hubs"
- check the "critical" box , insert the destination e-mail address into the "To" field then click "Save"
- check the "switches and Hubs" box and then click Save
As i know is possible to avoid to configure every single not-interesting port on the switches with "no snmp trap link-status" command (it's a bit annoying when you have tens of switches), using Port Grouping configuration on PI but i tried it without success.
Hope this helps.
Best Regards,

Consultations on Cisco Prime Infrastructure 2.2

I recently installed Cisco Prime Infrastructure 2.2 and I have 2 questions regarding configuration:
1. What configurations should run for vulnerability when some event occurs on a switch an alarm is lifted in the Cisco Prime Infrastructure 2.2?
2. Is there any way to put a device into maintenance mode in the web interface of Cisco Prime Infrastructure 2.2, so that can not be spoiled reports regarding equipment availability during the execution of maintenance?

1. If you configure PI as an SNMP and syslog server for your devices and have enabled logging traps etc., PI's alarm browser will show the alarms. If you want them to be sent to you via email, you can do that under the Admin menu for setting up your Mail server and clicking the link to "Configure email notification for individual alarm categories." (see below - open in new tab to zoom). It's not completely customizable but what you see there is the current product capabilities in that regard.
2. No, this is not currently an available feature in PI 2.2.

Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Similar Messages

Maybe you are looking for