Cisco Prime Infrastructure 2.1 Image Distribution Problem

Hey Guys,
Trying to upgrade a switch using Prime. The switch Sync's fine with Prime, SNMP and Telnet/SSH credentials seem to work. However when trying to push an Image I get the following errors in the job description:
Distributing image c3560-ipbasek9-tar.150-2.SE6.tar using protocol TFTP      FAILURE
Distributing image c3560-ipbasek9-tar.150-2.SE6.tar using protocol SCP        FAILURE
How can I find out more details as to what exactly the failure is?
Thanks!

Interesting note:
I found that when using the "Software Deployment" instead of the "Image" tab under a device in the "Device Work Center" to do upgrades, I encounter this problem less often.
However the problem still does occur at times and an additional problem I'm facing is that at times the upgrade jobs succeed fine, but the devices never get rebooted (in spite of having the snmp-server system-shutdown string in the config). In that case the job will never finish and shows as 'running' 10 days later. The Job also can't be cancelled or aborted successfully.

Similar Messages

  • Cisco Prime Infrastructure 1.3 Tacacs+ authorization problem

    Hello,
    We are having trouble setting our new installation of Cisco PI 1.3 to work with Tacacs+ configured on ACS 4.2.
    We have followed procedure explained in Cisco PI 1.3 configuration guide and in Tacacs+ logs we can see that we have successful authentification but authorization is unsuccessful:
    21/05/2013,16:36:44,Authen OK,pradoicic,admins,192.168.187.109,,192.168.187.109,wifi-prime-p-vm01,AP,ACS1AERO,1,,,192.168.187.109,No Filters activated.,,,No,
    21/05/2013,16:36:44,Author failed,pradoicic,admins,192.168.187.109,,Service denied,protocol=HTTP service=NCS,NCS HTTP,192.168.187.109,wifi-prime-p-vm01,AP
    We have added user group into ACS as is explained in configuration gude and we have also tried to add virtual domain at the beggining or at the and of the list but that didn't solve our problem.
    Is there anything that we can do in order to make Cisco PI to authentificate users using Tacacs+?
    Any help in finding solution for this problem will be very appreciated.
    Regards,
    Jelena

    Hi,
    On the Cisco PI side we have:
    1. Added Tacacs+ server under Administration > AAA > TACACS+
        We have entered all required parameters
    2. Enabled AAA Tacacs+ mode under Administration > AAA > AAA Mode and we have choosed on auth failure or no server response oprion.
    On the ACS side:
    1. Under Network Configuration > New Entry we have added Cisco PI
    2.  Under Interface Configuration >TACACS+ (Cisco IOS) > New Services >
    we have added Prime and HTTP (we have checked box infront of these service).
    3. Under Group Setup > Edit Settings > prime HTTP service we have added custom attributes that we have copied from Cisco PI Admin group. We have also exported virtual domain information from Prime and have imported them on the beggining of the custom attributes and we have also tried to place that virtual domain information on the end but we have the same behavior.
    For some reason ACS doesn't know how to return authorization information.
    Regards,
    Jelena

  • Can't import images in cisco prime infrastructure 1.2

    - Any job , trying to import images, in my cisco prime infrastructure fails with :
    Jan 14 13:14:53 cisco-prime  01/14/13 13:15:18.040 ERROR [service] [pool-4-thread-19] IFM_SWIM_EXCEPTION: [com.cisco.ifm.swim.service.exception.IfmSwimParserException: Cannot populate software image info object from the image.]
                       How I can I solve this one ?
    Tx,
    M.

    I seem to have the same problem, strangely enough importing a universal image for 2960s worked fine, but I get thos error when trying to import a 3750x image

  • Software images Cisco Prime Infrastructure

    Hi,
    I have Cisco Prime infrastructure 2.0 and all it works ok except when i try to get software image from device. I don´t see any device, so i can´t select any device and I get "RSL error".
    When i try to access "Operate" > "Configuration Archives", i get the same error.
    The machine from where I navigate has last "flash player" version and it has all requeriments.
    Which can be the problem?
    Thanks.

    Hi!
    I have experience the same problem under different tools in PI. I did notice it first under “Deploy>Monitoring deployment>Interface Health template>deploy and I get the 2032 error.
    I have learn that this occurs when you use a client with no internet connection and you try to start above deployment tools.
    What happens is that when you try to open such page in PI web interface, the flash player starts and try to get some files on the PI but the URL it get from the PI application points to a library that do not contains the file (Bug in PI?). The files the flash player looks for is called something like framework_4.5.1.21328.swz and spark_4.5.1.21328.swz and so on. The url from PI looks like https://PI_Server/webacs/applications/SAMDeployTemplate/js/framework_4.5.1.21328.swz but the file is missing.
    The flash player have a backup way to get the xxxxxx.swz files it needs. If it can’t find the files in the application, it try to get it from Adobe http://fpdownload.adobe.com . But in my case my client can’t access internet so I get the error 2032.
    I have another installation at another site that allows internet access everything works fine. The flash player can load the files it needs and store them locally on the client PC. Then I can take that PC back to the another site with no internet access where I did get the 2032 error and now It works fine because the flash player have the files it needs to handle the PI application.
    I have a case open and it has not been solved yet.
    Mattias.S

  • Cisco Prime Infrastructure 2.0 import image via WAN link failed.

    Cisco Prime Infrastructure 2.0 behind NAT that can copy image on device to Cisco Prime infra but can not deploy from Cisco Prime Infra import image from device. How to solve problem,please ?

    Have you downloaded and applied the latest Device Pack updates?
    PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
    The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location.

  • Cisco Prime Infrastructure - I can't see the hardware virtual image when I selected a device managed by Prime Infrastructure. See attached picture

    My Cisco Prime Infrastructure ver. 1.2.1.12
    Cisco Prime Infrastructure - I can't see the hardware virtual image when I selected a device managed by Prime Infrastructure. See attached picture.
    Please let me know how to access or enable the feature.
    Thanks,
    Tek

    This is by no means a full solution, but deleting and re-adding only takes a few minutes if you use the "Export Device" and "Bulk Import" features from the Device Work Center. You can export the desired devices to a CSV file, delete them, then import from the CSV. 
    Of course, you might lose historical data when deleting the devices, but I'm guessing that's not as relevant since the devices themselves have been replaced by different hardware.

  • Problem with implementing license in Cisco Prime Infrastructure 2.2

    Goodday,
    For Cisco Prime Infrastructure 2.2 I downloaded an license from the license portal.
    This concerns a eval/demo license, for an demo of Cisco Prime Infrastructure 2.2.
    When selecting the the type of license you get a few options, from which I selected the basic, advanced and lifecycle evaluation licenses. This is the type of license that is required for our demo.
    After completing the wizard I can download en implement the license.
    Until this point everything goes as it supposed to be.
    When i go to the Prime Infrastructure 2.2 appliance (running on VMWare ESXi 5.5.0).
    When I go to the license section in Cisco Prime Infrastructure I can implement the license, however if I implement the .lic file I get the error “Unknown feature (PI_VM)”.
    I have done implementing license files before, but this is the first time i encounterd this problem.
    Who can help me with this error?
    Regards,
    Dennie Verhoeven

    Hi Dennie,
    PI2X-BASE-LF-AS-US-VM-N-EVAL-90   >> I think you have used this product name while generating the license
    Either you try generating a new license or  contact cisco license team to generate a new license
    with the information  like below ::
    Product Name                : R-PI2X-K9
        Product Description         : R-PI2X-K9:R-PI2X-K9 : Cisco Prime Infrastructure 2.x
        Product Qty                 : 1
        UDI                        : PID: PRIME-NCS-VAPL  SN: ANY:ANY
    Serial no : with ANY:ANY will work as  starting from PI 2.2 , there is no node locking with license.
    Thanks-
    Afroz
    ****Ratings Encourages Contributors ****

  • Cisco Prime Infrastructure 2.0 and ASA 55xx platform problem

    Hello,
    We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
    When I attempt to add ASA's to prime i get the following collection errors:
    Unable to collect processor and RAM information.          Processor and RAM information.          Unexpected error. See the log file inventory.log for details.
    In the logfile I get the following XML parsing error on the MIB:
    <palError>
      <deviceId>6284310032</deviceId>
      <code>VALIDATION_ERROR</code>
      <message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
      <result>
        <result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
          <xmp-im-file-system-module>
            <MemoryPoolStatistics>
              <memoryPoolIndex>1</memoryPoolIndex>
              <free>4294967295</free>
              <largestFree>4294967295</largestFree>
              <used>3484331296</used>
            </MemoryPoolStatistics>
    To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
    Regards,
    Marcel

    Hi,
    does anyone happen to know if that problem is fixed? My currently setup looks like this:
    1. Cisco Prime Infrastructure 2.1 with updated device pack.
    2. Assurance license
    3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
    I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
    regards
    Maurus

  • Cisco Prime Infrastructure 2.0 and Cisco ASA

    Hello,
    We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
    First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
    Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
    ASA version is 5505, image is 9.1(2).
    So, I have a question: is it possible to manage ASAs with PI 2.0?
    UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.

    Have you downloaded and applied the latest Device Pack updates?
    PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
    The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location.

  • Cisco Prime Infrastructure 2.1 - WS-C2940-8TF-S and WS-C2940-8TT-S supported ?

    Hello community,
    I've got a question just to play safe.
    I'm running a Cisco Prime Infrastructure 2.1, we still do have a bunch of WS-C2940-8TF-S and WS-C2940-8TT-S with running images 12.1(22)EA12 , 12.1(22)EA13 and 12.1(22)EA14.
    I know these switch types already have a End-of-Sale and End-of-Life Announcement for the Cisco Catalyst 2940-8TT-S and 2940-8TF-S Compact Switches ("http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-2940-series-switches/end_of_life_notice_c51-510224.html").
    The inventory collection status in the device work Center is for these switch types "Collection Failure", the error message is this one:
    An unexpected error has occurred:
    # Check the device is in supported device list in deployment guide -> not listed in "http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-1/release/notes/cpi_rn.html#pgfId-43885"
    # Check there is connectivity between the device and PI -> Checked adnd OK
    # Check the device credentials provided are valid -> Checked adnd OK
    # Finally if the problem still persists then contact Cisco System's technical assistance center -> not done yet, looks like these switch types are not supported any more in PI 2.1 ?
    Can anyone confirm this or answer back because these switch types are supported in her/his PI2.1 installation?
    Best regards
    Bastian

    Prime Infrastructure won't support those legacy models.

  • WCS and LMS to Cisco Prime Infrastructure 1.3 Upgrade

    Hello,
    Our customer is currently having WCS for 500 devices and LMS 3.2 for 1500 devices. We are planning to upgrade to Cisco Prime Infrastructure 1.3.
    I want to check is the upgrade procedure that we have planned is ok or we have missed something.
    Phase 1: WCS to CPI 1.3 upgrade
    1. Check that WCS is at 7.0.230.0  version
    2. Export WCS database
    3. Install NCS 1.1.1.24 software
    4. Contact cisco to obtain trial license for NCS software (L-WCS-NCS1-M-K9 license).
    5. Migrate WCS license and import it in NCS software
    6. Migrate WCS data to NCS software using ncs migrate command
    7. Patch NCS software
    8. Inline upgrade to CPI 1.3 software
    9. Install proper licenses on CPI 1.3 (WCS and LMS device count)
    My concern in this first phase is should I use NCS large image since our Cisco Prime Infrastructure 1.3 software should manage 2000 devices at the end.
    Or is it better not to perform inline upgrade and insted go with exporting data from NCS and then importing them to CPI 1.3 that is going to be installed separately?
    Phase 2: LMS 3.2 to CPI upgrade
    1. Export LMS 3.2 database
    2. Install LMS 4.2 software
    3. Install license to LMS 4.2
    4. Restore data from LMS 3.2 to LMS 4.2
    5. Direct upgrade from LMS 4.2 to 4.2.2
    6. Export the device list with credentials from LMS 4.2.2  and import it as a Bulk Import in CPI 1.3
    At the end we will have CPI 1.3 and LMS 4.2.2 software running.
    Is it possible to directly upgrade from LMS 4.2 to LMS 4.2.4 and then import data to CPI 1.3 or we need to go with 4.2.2 version?
    Regards,
    Jelena

    Hello Marvin,
    We have restored LMS 3.2 SP 1 database on LMs 4.2 and we have got some error messages during restore. Please see our restore output:
    [kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/res
    resolver.pl           restoreDBTableMig.pl  restoreJRMMig.pl      restorebackup.pl     
    [kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/restorebackup.pl -d /opt/BKP/
    Restore started at : 2013/12/05 14:11:58
    Please see '/var/adm/CSCOpx/log/restorebackup.log' for status.
         USER ID is ..................................... : sysadmin
         OS of the backup archive is..................... : Windows
    INFO:The backup archive is from a different OS. Your current Platform is: Soft Appliance .
    You are attempting to perform a Cross Platform Restore..
    Do you wish to continue (Y/N) [Y] :Y
         Generation to be restored is ................... : 0
         Backup taken from............................... : /opt/BKP/
         Common Services version in the backup data is... : 3.3.1
         Common Services is installed in................. : /opt/CSCOpx
         The temp folder for this restore program........ : /opt/CSCOpx/tempBackupData
         Applications installed on this machine ......... : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][cwportal][ipm][upm][cvw][cwlms]
         Applications in the backup archive ............. : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][opsxml][cwportal][ipm][upm][cvw]
         WARNING: The list of applications installed on this CiscoWorks server does not match the list of
                  applications in the backup archive. If you restore data from this backup archive,it may
                  cause problems in the CiscoWorks applications.
                  Do you want to continue the restore operation?  (y-continue or n-quit, y/n)?Y
         Applications to be restored are................. : [Common Services] [Campus Manager] [Resource Manager Essentials] [Device Fault Manager] [cwportal] [ipm] [upm] [cvw]
         Available disk space in NMSROOT................. : 86451488 Kb
         Required disk space in NMSROOT.................. : 35906524 Kb
         (The temp and NMSROOT are on same device, therefore this required disk space includes temp space)
      Copying the backup files to the temporary location [/opt/CSCOpx/tempBackupData]
      preRestore of [Common Services] has started.
      preRestore of [Common Services] has completed.
      preRestore of [Campus Manager] has started.
      preRestore of [Campus Manager] has completed.
      preRestore of [Resource Manager Essentials] has started.
      preRestore of [Resource Manager Essentials] has completed.
      preRestore of [Device Fault Manager] has started.
      preRestore of [Device Fault Manager] has completed.
      preRestore of [cwportal] has started.
      preRestore of [cwportal] has completed.
      preRestore of [ipm] has started.
      preRestore of [ipm] has completed.
      preRestore of [upm] has started.
      preRestore of [upm] has completed.
      preRestore of [cvw] has started.
      preRestore of [cvw] has completed.
      doRestore of [Common Services] has started.
              Cross Platform Update started.
              Cross Platform Update completed.
              License check started.
                 WARNING: The license details in the server are different from the backup data.
                          After restoring, please check the license available in the server.
                 WARNING: Your current license count is lower than your earlier license count.
                          If you restore the data now, devices that exceed the current licence count
                          will be moved to Suspended state.
              License check completed.
              Restoring certificate.
                 WARNING: Cannot evaluate the hostname, hence the certificate
                          may be from this host or another host.
                          [  Certificate not overwritten  ]
              Restored Certificate.
              Restoring Common Services database.
              Restored Common Services database.
              Restoring CMIC data.
              Restored CMIC data.
              Restoring CMC data.
              Restored CMC data.
              Restoring Security Settings.
              Restored Security Settings.
              Restoring DCR data.
              Restored DCR data.
              Restoring Certificate key store.
              Restored Certificate key store.
      Restoring DCNM CrossLaunch data.
              Restored DCNM CrossLaunch function.
              Restoring JAAS configuration.
              Restored JAAS configuration.
              JRM Job Migration started.
              JRM job Migration done.
      doRestore of [Common Services] has completed.
      doRestore of [Campus Manager] has started.
              Cross Platform Migration for Campus started.
    Cross Platform update Starts for Campus
      doRestore of [Campus Manager] has completed.
      doRestore of [Resource Manager Essentials] has started.
    10% of RME  Restore completed
    30% of RME  Restore completed
    50% of RME  Restore completed
    70% of RME  Restore completed
    100% of RME  Restore completed
      doRestore of [Resource Manager Essentials] has completed.
      doRestore of [Device Fault Manager] has started.
    10% of DFM Restore completed
    30% of DFM Restore completed
    50% of DFM Restore completed
    80% of DFM Restore completed
    Going to modify Eight PM report 
    Modified Sucessfully Eight PM report 
    100% of DFM Restore completed
      doRestore of [Device Fault Manager] has completed.
      doRestore of [cwportal] has started.
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.properties  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.script  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.log  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultUserCommunity.properties  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultCommunity.properties  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
      doRestore of [cwportal] has completed.
      doRestore of [ipm] has started.
            10% of IPM Restore Completed
            30% of IPM Restore Completed
            50% of IPM Restore Completed
            60% of IPM Restore Completed
            70% of IPM Restore Completed
            100% of IPM Restore Completed
      doRestore of [ipm] has completed.
      doRestore of [upm] has started.
    HUM database restore starts
    INFO:STOP= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
    SQL Anywhere Command File Hiding Utility Version 10.0.1.4239
    INFO: Database Shutdown is in Progress..Please wait
    INFO: Stop Engine Args= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
    INFO: After Database Shutdown RC= 2304
    root=C:\PROGRA~2\CSCOpx\databases\upm\upm.db
    DBUTILS: Inside Cross Platform
    INFO: Current Database password does not match the password of Database being restored
    INFO: Using the Password of the Database being restored
    HUM database restore successfully completed.
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate/README.txt
    Directory is reportsStarted changing property .
    linux
    Restored HUM configuration file successfully.
      doRestore of [upm] has completed.
      doRestore of [cvw] has started.
      doRestore of [cvw] has completed.
      postRestore of [Common Services] has started.
      postRestore of [Common Services] has completed.
      postRestore of [Campus Manager] has started.
      postRestore of [Campus Manager] has completed.
      postRestore of [Resource Manager Essentials] has started.
      postRestore of [Resource Manager Essentials] has completed.
      postRestore of [Device Fault Manager] has started.
      postRestore of [Device Fault Manager] has completed.
      postRestore of [cwportal] has started.
      postRestore of [cwportal] has completed.
      postRestore of [ipm] has started.
      postRestore of [ipm] has completed.
      postRestore of [upm] has started.
      postRestore of [upm] has completed.
      postRestore of [cvw] has started.
      postRestore of [cvw] has completed.
    Restored successfully.
    Are this errors going to affect our LMS 4.2 operations?
    Then we have upgraded to LMS 4.2.2 and exported data and credentiales for PI import.
    On PI 1.3 we have installed WCS 500 devices upgrade license and LMS 1500 upgrade license and now we are having 2000 devices lifecycle license. We have successfully restored WCS data in PI and we have imported LMS devices as bulk import. What is strange is that we have this message in prime regarding licensing:
    On LMS 3.2 our customer had saved unlimited number of configuration versioning. After upgrading to LMS 4.2 we can only see last 3 configurations regardless of unlimided number of configurations in previous LMS, so my question is where can we find older configurations in LMS 4.2?
    We are planning to turn unlimited versioning on CPI 1.3 now, so our customer will again have feature that they need. Do you have some experiance regarding disk space when all device configurations are stored forever?
    Thank you for your help.
    Regards,
    Jelena

  • Trouble With Cisco Prime Infrastructure 1.3

    Hi,
    I have installed the Evaluation Version Cisco Prime Infrastructure 1.3.
    There are a few problems that i am facing;
    I am trying to push a simple configuration to WLC using Prime Infrastructure. But it is failing as PI doesnot have RW SNMP access.
    My question is that can I use PI to push configs without using SNMP. Like do it using ftp or something.
    Also do the Wired Devices also need SNMP RW access on PI's part.
    2. I tried running discovery for WLC and it worked fine where all the controllers were discovered. But when I try to discover a Switch, the reachability tab says Reachable but in Collection Status tab it shows Unmanaged. When I click on the Unmanaged tab it says " Pre-collection check failed because: ". I have configured the SNMP correctly.
    3. I have the CAD files for all the maps in our environment but when I try to upload it to Prime it converts it into GIF, so the maps are uploaded as plain image with no knowledge of walls and obstacles.
    So we would have to add the walls and obstacles by ourselves. Is there any way it can automatically pick up on the walls and obstacles and thus provide a better way for predicting RF profiles.
    All your help is greatly appreciated.

    TAC Case! Sounds like a bug to me...
    Sent from Cisco Technical Support iPad App

  • After Update Cisco Prime Infrastructure from 1.3 to 2.0 imported floor plans has black background

    Hello everybody,
    we have updated cisco prime infrastructure from 1.3 to 2.0. When we now import a floor plan (autocad-file, dwg-format), the background from finally image, that is show in prime, is black. Previous imported floor planes has a white background. We also tried to import a previous imported floor plan again, the background is now black. Is there a possibilty to change the background to white? Thanks

    Hi,
    Look no further, these issues are related to know bugs. It seems that autocad files have multiple issues with PI 2.0, Only feasible way is to convert them to JPGs and import them. Lets hope these will get fixed to the level they where at PI 1.3.
    CSCuj63017, PI 2.0 dwg(AutoCAD file) import reports Tailormade is for Demo use only
    Symptom:
    When dwg files are imported to Prime Infrastructure, they report
    "For Demonstration Purposes only
    Tailor made software"
    Conditions:
    Prime Infrastructure - 2.0.0.0.294
    Use of dwg (Auto cad) files
    Workaround:
    None at this time
    Further Problem Description:
    CSCuj94500, Loading DWG floor maps on PI 2.0 appears in black background
    Symptom:
    On PI 2.0 when we try to import autoCAD .dwg file to map, the map appears in black background.
    Conditions:
    On PI 2.0 when we try to import autoCAD .dwg file to map
    Workaround:
    use 3rd party tool like Draftsight or AutoCAD Trueview to change the file to .jpg and import again to PI, after that the map appear in white background in PI 2.0.
    Further Problem Description:
    However, the same .dwg file when we imported it to PI 1.3 appear in map with white background.

  • Cisco Prime Infrastructure 1.2 is not working https & ncs

    Hi, I have just deploy Cisco Prime Infrastructure 1.2 in a virtual appliance (Vmware Esxi 5.1). Console is ok & setup is also completed. but there is no NCS application. only app is shwoing: NCSPNP
    Cannot access from https also.
    Please suggest how to Starting Prime Infrastructure Serve

    From what you describe, it sounds like you have installed the Plug and Play (PNP) ova image. You need to install the Prime Infrastructure image.
    See the screenshot below for details (click to enlarge):

  • Cisco Prime Infrastructure 1.2 on Windows Server/Hyper-V

    Hi Everyone,
    In Entriprise environment while designing a BYOD solution we need to integrate ISE3315 with CPI 1.2. I know that Cisco ISE software either runs on 3315 platform or other option is virtual appliance (which is VMware based). Now problem is that we have Hyper-V environment as standard so I need to go with ISE-3315. Here my concern is to I install CPI 1.2 on Hyper-V, or on a Windows Server (2008 or 2012) based machine. Is that doable?
    Any help, suggessions would be warmly welcomed.
    Thanks,
    Azhar...

    Cisco Prime LMS will slowly be phased out in favor of Cisco Prime Infrastructure and hence there are no new mainline releases are planned to provide support to new Hardware or virtualization support.
    However, Prime LMS do support Hyper V Virtualization (As an installable in Windows 2008). Please note that Virtualization technologies like, VMWare and Hyper V virtualization systems are not supported in LMS 5000, and LMS 10000 Devices license, in Windows. VMWare Systems are supported in LMS 5000, and LMS 10000 Devices license in Soft Appliance. Virtualization technologies like, VMWare and Hyper V virtualization systems are not supported in LMS 5000, and LMS 10000 Devices license, in Windows. VMWare Systems are supported in LMS 5000, and LMS 10000 Devices license in Soft Appliance.
    For more details on HW and SW requirements for Cisco Prime LMS, please check document here.
    -Thanks
    Vinod

Maybe you are looking for