Cisco Prime Infrastructure 2.1 to setup Discovered Devices in Dashboard Detail auto refresh in 3 minutes
Hi all:
I found out that the discovered devices (after successful scanning) in the main Dashboard Detail cannot or take very long time to auto-refreshing the status change.
May I know is there any way by Command Line at the "Root" (I am using an OVA version) or by setting inside the Prime Infrastructure with GUI method to do scheduled Refreshing on the Dashboard Detail?
Thanks!
Best regards,
tangsuan
Hi all:
I have tried using Designing Monitoring Template to set the Health Check Polling time from default 15 minutes to 5 minutes and also tried also 1 minute.
The result is 5 minutes is working but 1 minute is not working.
May I know any one can help on this?
Many thanks!
Best regards,
tangsuan
Similar Messages
-
Hello everyone,
Last month I was in London (Cisco Live 2013) I have spoken with a Cisco Prime (BU) Specialist. He told me verbally that there is currently a 75% discount for L-PI12-1.5K-UP. Can anyone confirm this and tell me what the part number is?
Thanks !
Gertjan Scharlooyou would need to contact your Cisco Partner/SE to be able to get those details.
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered -
Hi All,
Im getting a bit confused about the whole upgrade migration process for the following config to Cisco Prime Infrastructure:
LMS - Version 4.1 , 500 devices. Windows Server 2008 R2 Standard SP1
NCS – version 1.1 , 50 devices Red Hat Linux ( 64 Bit) (Installation software - NCS-VA-1.0.1.4-small.ova)
I want to be able to backup databases and migrate licensing from LMS and NCS to one platform. Does anyone have experience of this and could possible guide me thorugh this process. LMS has SAS and NCS has SAU.
Help will be very much appreciated!!It's a couple of steps but can be done. You may want to reconsider getting off of LMS since the latest Prime Infrastructure (PI 1.2) does not have full feature compatibility with the latest LMS (4.2.3). Have a look here for the comparison.
If you still want to do it:
1. Upgrade your NCS to PI 1.2 (instructions). If you're going with a total of 550 devices on a combined license you should use the medium ova file to get the correct server resource allocation. You will need to get the new license from the TAC or via the licensing portal. I'm not sure if you can get the PI license for your LMS upgrade directly via the portal but you do have the entitlement for LMS 4.2 and PI 1.2 (combined licenses not to exceed the original LMS number) if your SAS is current. You may need to contact the TAC and ask for the licensing team.
2. Upgrade your LMS to 4.2 and patch it to 4.2.2 (instructions). Once you've done that, there is a simple menu command to export your device credentials to Prime (Admin, System, Export Data to PI in LMS and then Operation, Device Work Center, Bulk Import in PI - instruction on Page 18 here). Do that and then in the new PI installation import the devices.
Verify everything is working and you can decommission the LMS server. -
Cisco Prime Infrastructure, Express, licensing
Are there any funcionatility limitation between each edition of the Cisco Prime Infrastructure other than supported number of devices?
Does it support turning APs on and off on a predefined scheduled?
I read in the manual "Cisco Prime Infrastructure Classic View Configuration Guide for Wireless Devices" that it is possible to Managing WLAN Status Schedules. Does it require the assurance license feature set or will lifecycle license will be sufficient?I believe you could create a scheduled Lightweight AP Configuration Template job and have it simply turn off the radios on the selected APs. Make it recurring (every night at a certain time) and add a complementary recurring job to turn the radios back on at the desired time.
See the following screeenshot from PI 2.0 (click to enlarge): -
Cisco Prime Infrastructure 2.2 clients and users IPs not detected
Hi all,
I have cisco PI2.2 and discovered all the network and i notified that there are some clients' IPs (Servers or PCs or Laptops or ....) not detected.
please advice what may be the issue ?Hi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus -
Cisco Prime Infrastructure 1.2 is not working https & ncs
Hi, I have just deploy Cisco Prime Infrastructure 1.2 in a virtual appliance (Vmware Esxi 5.1). Console is ok & setup is also completed. but there is no NCS application. only app is shwoing: NCSPNP
Cannot access from https also.
Please suggest how to Starting Prime Infrastructure ServeFrom what you describe, it sounds like you have installed the Plug and Play (PNP) ova image. You need to install the Prime Infrastructure image.
See the screenshot below for details (click to enlarge): -
User Name and Password for Cisco Prime Infrastructure 2.1
Hi all:
I am stuck at the login page of Cisco Prime Infrastructure 2.1.
I have tried using the user name root and its password (when log in with root at Vsphere Client) and also the login user name "before" get into the appliance infrastructure, all cannot work.
Anybody knows what is the default username or password or any way to set the username and password for this Cisco Prime Infrastructure 2.1 website?
Thanks!
tangsuanHi Tangsuan,
Following is the documented procedure for password recovery..
In order to modify the GUI root user password, you will need to login to the NCS CLI
as an admin user, and enter the command
"ncs password root password <new password>" (without the quotes)
This should set the web interface root user password :
http://www.cisco.com/en/US/docs/wireless/ncs/1.1/configuration/guide/manag.html#wp1268889
If you have lost your CLI password , try the default logging that is ,
CLI user is admin and not root, so please try logging in as admin with
the password that was set during setup. If that does not work , you need
the install disk that came with the appliance to recover that password.
Follow these steps:
Recovering a Lost Admin Password
If you lose or forget the admin password for NCS appliance, follow these steps.
Step 1 Reboot the NCS appliance with the ISO DVD inserted. The Cisco Prime Network Control
System Welcome screen appears:
ISOLINUX 3.11 2005-09-02 Copyright (C) 1994-2005 H. Peter Anvin
Welcome to Cisco Prime Network Control System
To boot from hard disk, press <Enter>.
Available boot options:
[1] Network Control System Installation (Keyboard/Monitor)
[2] Network Control System Installation (Serial Console)
[3] Recover administrator password. (Keyboard/Monitor)
[4] Recover administrator password. (Serial Console)
<Enter> Boot existing OS from Hard Disk.
Enter boot option and press <return>.
boot:
Step 2 Select the desired recovery option, 3 or 4, depending on how you
are connected to the appliance and then follow the prompts.
Thanks-
Afroz
***Ratings Encourages Contributors **** -
Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices
Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
0 Bad SNMP version errors
14 Unknown community name
0 Illegal operation for community name supplied
0 Encoding errors
38453185 Number of requested variables
0 Number of altered variables
17790703 Get-request PDUs
20583581 Get-next PDUs
0 Set-request PDUs
0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
0 Too big errors (Maximum packet size 1500)
0 No such name errors
0 Bad values errors
0 General errors
38371069 Response PDUs
13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
JeremyHi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors **** -
Cannot add WLC 5508 7.2.111.3 to Cisco Prime Infrastructure 2.0
Though the Cisco Prime Infrastructure Compatibility Matrix list out that 7.2.111.3 is supported for PI 2.0
I am not able to add the controller to the PI 2.0.
The Reachability Status always shown "Unknow" and SNMP Status always shown "No response for SNMP Get".
There is no firewall between the WLC and PI.
And ping test shows it is reachable.
If I try to add controller by non-management port (I know it is not work but I want to try the reachability), the Reachability Status shown "Reachable" but the SNMP Status always shown error.
And if I use some SNMP testing software to test the SNMP port. SNMP can be quoted.
I have try to lower down the "Maximum VarBinds per Get PDU" but no luck.
Any thing I can do to troubleshoot the problem?Yes, I follow the procedure but it does not work.
Another update:
I add another WLC with version 7.0.98.0. It is fine.
And I setup another new PI 2.0 and new temporary WLC5508 with 7.2.111.3 to test. It work fine also......
So, I am wondering the existing 7.2 WLC have problem in responsing the SNMP Get. But I dont have any idea to test....
Do anyone have idea to test the snmp connection between PI and WLC? -
Cisco Prime Infrastructure 2.2 - Network Topology error
He dears,
My Customer has installed over UCS Cisco Prime Infrastructure 2.2.
The network is composed with Switches nexus 93962-px and 2960x. All devices were discovered and inventoried successfully.
The problems is that Network Topology is not showing the connections between devices. Some devices connections are showed (partially) and another not.
We've already checked that CDP is run and working fine on all of switches.
I appreciate your help!
Tks,
RegisI'm sorry to say that but Prime Infrastructure does not support IP SLA functionality similar to Cisco Prime LMS:
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/guide_c07-729089.html
It's in the developer's plans but there's no schedule yet for this feature.
It's possible to manually configure IP SLA on the device and then define Custom SNMP templates in Prime Infrastructure and poll whatever information you might consider relevant.
This isn't user friendly (exact OID needs to be typed manually) and is a bit quite complicated, though.
-Thanks
Vinod
**Rating Encourages contributors, and its really free. ** -
New installation of Cisco prime Infrastructure 1.2
Hi,
We installed Cisco prime infrastructure 1.2 and discovered our entire LAN swtiches and core L3 Switches.
In Cisco Prime, we are getting information related to Device and IOS. But intreface ulitilzation information are not avilable.
we used SNMPv2 RW string and and SSH username for discovery.
How to get the interface ulitization data ?Under Administration > System Settings, then select Monitoring Settings.
i checked the two options
Auto monitoring
Enable deduplication
But after refresh it is show uncheck, i tried in Google Chrome and Firefox.
Is this cause the issue of not polling interface netflow??? -
Device Reachable but Unmanaged in Cisco Prime Infrastructure 1.3
Hi,
I am running the Eval version of cisco Prime Infrastructure 1.3
I tried running discovery for WLC and it worked fine where all the controllers were discovered.
But when i try to discover a Switch, the reachability tab says Reachable but in Collection Status tab it shows Unmanaged.
When i click on the Unmanaged tab it says " Pre-collection check failed because: "
I have configured the SNMP correctly.
Does anyone know why is this happening.
All the help is greatly appreciated.Had the same issue and noticed that the licence count for 100 devices (Eval Limit) was consumed as soon as we added the WLC
On your page https:///webacs/welcomeAction.do#pageId=LicenseCenter_pageId look at how many are taken and if it is in violation.
We added our 500 pak upgraded, and it still didn't fix the issue when re-syncing. We had to remove the device and re-add.
This is now resolved for us. -
Trouble With Cisco Prime Infrastructure 1.3
Hi,
I have installed the Evaluation Version Cisco Prime Infrastructure 1.3.
There are a few problems that i am facing;
I am trying to push a simple configuration to WLC using Prime Infrastructure. But it is failing as PI doesnot have RW SNMP access.
My question is that can I use PI to push configs without using SNMP. Like do it using ftp or something.
Also do the Wired Devices also need SNMP RW access on PI's part.
2. I tried running discovery for WLC and it worked fine where all the controllers were discovered. But when I try to discover a Switch, the reachability tab says Reachable but in Collection Status tab it shows Unmanaged. When I click on the Unmanaged tab it says " Pre-collection check failed because: ". I have configured the SNMP correctly.
3. I have the CAD files for all the maps in our environment but when I try to upload it to Prime it converts it into GIF, so the maps are uploaded as plain image with no knowledge of walls and obstacles.
So we would have to add the walls and obstacles by ourselves. Is there any way it can automatically pick up on the walls and obstacles and thus provide a better way for predicting RF profiles.
All your help is greatly appreciated.TAC Case! Sounds like a bug to me...
Sent from Cisco Technical Support iPad App -
Cisco Prime Infrastructure 2.0 : Nms:RAID - RAID is Bad Detect rebuild progress
Hi,
I'm having problem on our Cisco Prime Infrastructure 2.0 which is always happen HDD failure.
FYI, HDD failed at Slot 1.
This is details of message taken from our Cisco Prime alarms;
raid is bad detect rebuild progress... enclosure = 252 enclosure = 252 drive 255 is missing or bad
For your information, I was enter into RAID BIOS to saw the error. I got Slot:1, SAS, HDD, 278.464GB, Failed.
I also do the Rebuild drives on that HDD. After Rebuild is completed the HDD back to ONLINE.
But I still face the same problem for the next day.
Please help us to resolved the problem.
Thanks and Regrads.
Mohd Syukri Kaus
BIT Group Sdn BhdYou have the necessary CPU, memory and hard drive specifications for an Express size installation (Reference).
To install Prime Infrastructure 2.0 you will need to first install VMware ESX/ESXi. This is documented in the same Getting Started Guide I linked to above at this link.
Once you get that far along, just follow the setup wizard and installation is pretty simple.
FYI you will get better attention to Prime questions over in the Network Management forum. -
Cisco Prime Infrastructure 2.0 and ASA 55xx platform problem
Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information. Processor and RAM information. Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
<result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
<xmp-im-file-system-module>
<MemoryPoolStatistics>
<memoryPoolIndex>1</memoryPoolIndex>
<free>4294967295</free>
<largestFree>4294967295</largestFree>
<used>3484331296</used>
</MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
MarcelHi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus
Maybe you are looking for
-
Icon missing from System Preference on MacBook Pro. Please Help
The icon for my mail, contacts and calendars is no longer under my System Preferences. Can someone help me get it back? Thanks.
-
How to see "non converted" youtube videos on iphone
I have a few of my own videos loaded at youtube and wanted to see them on my iphone but they aren't among those converted to the iphone format. But there's a website called zamzar.com that will convert any of the youtube videos to the iphone format f
-
Console message just prior to time of latest freeze MBP i7
6/5/10 6:32:14 PM PreferenceSyncClient[244] Preference plist was NOT a dictionary. 6/5/10 6:32:14 PM PreferenceSyncClient[244] Preference plist was NOT a dictionary. 6/5/10 6:32:19 PM PreferenceSyncClient[244] Preference plist was NOT a dictionary. 6
-
Hi there, In the process of learning Visual Studio (VS) and ASP.NET, I initially thought that I could use Blend for VS's seemingly great HTML/CSS WYSIWYG editor to visually design the HTML pages and CSS for a web app developped with VS, whether it be
-
I'm seeing a lot of this lately and they're all sent from Exim 4.6x on FreeBSD Anyone else seeing this? I don't see a known vulnerability in Exim posted anywhere. <html> <body> What are you thinking...if pat sees this your divorced dude. :-{) see for