Cisco Prime Infrastructure 2.1 wired client show Wrong port speed.

Hi,
i have odd issue for some reason the port speed in the wired clients shown a wrong speed,
can some explain how the speed detremained and why i'm getting a wrong speed port of 10mb for a pc/host when my network is at least 100mb,
thanks

Hi all,
after a TAC with cisco they open a new BUG # CSCur33328
https://tools.cisco.com/bugsearch/bug/CSCur33328/?reffering_site=dumpcr
thanks

Similar Messages

Prime Infrastructure 2.2 - Wired Clients and Trunk Ports

We have our VMWare ESX hosts connected to our server access switches via trunk ports. Prime doesn't seem to track clients on trunk ports (to avoid showing clients on uplink ports between switches, I'm sure). Since these are not switch-to-switch connections, is there a way to enable Prime to track wired clients on these specific trunk ports so we have MAC/IP client info in Prime for our virtual environment?

Hi,
PI discards all the MAC table entries that are on trunk ports for a switch. This enhancement was added from PI 2.1 & later.
- Ashok
Please rate the useful post or mark as correct answer as it will help others looking for similar information

Cisco prime infrastructure not detect IP address of clients

hi all,
I have Cisco Prime infrastructure 1.2 and when move to monitor >> clients tab it lists me all the clients in my network but their IP address list estates "not detected" ?
please any advice?
I appreciate your kindly support.

Just an update that while this appears to have worked fairly well (as far as Cisco Management Planes go), there was one small 'gotcha' I've noticed so far:
After the services came back up, the entries for our RADIUS servers did not function. No, not because I didn't update the clients address record on the RADIUS server itself, but because the RADIUS server record(s) within CPI have a field called 'Local Interface IP' that still reflects the previous IP assigned to CPI. A quick edit/save with the new interface fixes up the issue however.
Cheers!

Cisco Prime Infrastructure 2.2 clients and users IPs not detected

Hi all,
I have cisco PI2.2 and discovered all the network and i notified that there are some clients' IPs (Servers or PCs or Laptops or ....) not detected.
please advice what may be the issue ?

Hi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus

Cisco Prime Infrastructure 2.0 not showing alerts from switch

Hello,
I have a prime infrastructure 2.0 running at a customer place and the customer now complains that he is not receiving link up/down messages from the switch. When i checked I have seen that if I shut down a port in the switch the prime identifies after a long time, but its not generating an alarm still. How can I fine tune the prime to fix this issue. Please help on this.
Thanks in advance

Hi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work?

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

• PI provides visibility for autonomous clients within the same list view as lightweight and wired clients (client list page).
• Rogue AP detection for autonomous AP's is not supported (it's supported in CUWN).
• Alarms/events for client authentication issues (e.g. authentication failure) are displayed in PI.
• Config management for autonomous AP's is via CLI template. Config comparison and archiving functionality in PI leverages these same features that were brought in from LMS, so need to defer to others in terms of whether this is a cross-platform feature in PI or is only supported on a subset of platforms. Config comparison/archive is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client sessions, etc.) reports, and there are extensive reports for CUWN

Prime Infrastructure 2.0 does not show Planning Mode

Hi,
I´d like to know if evaluation version of Cisco Prime Infrastructure 2.0 (PRIME-NCS-VAPL) does not provide the feature "Planning Mode" to conduct a Predictive Site Survey.
Monitor>Site Maps>Select an Site>
At the drop down list (select a command), I can´t see planning mode. The options are: New Building, New Outdoor Area, Edit Campus/Site, Delete Campus/Site, Configure Interferer Notifications.
I also notice that "Add Access Points" does not appear.
see the att image.
Tks.

Hi ,
1. Monitor > Site Maps
2. Select the appropriate location link from the list that appears.
A color-coded map appears showing placement of all installed elements (access points, clients, tags) and their relative signal strength.
CLICK on the " color-coded map "
Now on the right hand side Drop Down Menu , you should be able to see the "Planning Mode"
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Cisco Prime network and cisco prime infrastructure

Hi,
What is the difference between Cisco Prime Network and Cisco Prime infrastructure.
Please advice.

I assume you are asking about Cisco Prime LAN Management System (LMS) vs. Cisco Prime Infrastructure (PI).
LMS is currently the leading Cisco offering for wired infrastructure management. It is the evolution of the earlier CiscoWorks LMS, CiscoWorks RWAN CiscoWorks 2000, CWSI, VLAN Director, original CiscoWorks classic etc. products going back almost 20 years.
PI is the equivalent Cisco offering for wireless LANs and is the successor to NCS and WCS products.
The overlap and confusion comes from the fact the Cisco is positioning PI as the overall wireless and wired management platform and gradually introducing wired network management features to make it equal (and eventually exceed) LMS's capabilities.
There is a comparison table here that shows the current differences. A major new release of PI (2.0) is due out shortly which will close many (but not all) of the gaps on that table.

Trouble With Cisco Prime Infrastructure 1.3

Hi,
I have installed the Evaluation Version Cisco Prime Infrastructure 1.3.
There are a few problems that i am facing;
I am trying to push a simple configuration to WLC using Prime Infrastructure. But it is failing as PI doesnot have RW SNMP access.
My question is that can I use PI to push configs without using SNMP. Like do it using ftp or something.
Also do the Wired Devices also need SNMP RW access on PI's part.
2. I tried running discovery for WLC and it worked fine where all the controllers were discovered. But when I try to discover a Switch, the reachability tab says Reachable but in Collection Status tab it shows Unmanaged. When I click on the Unmanaged tab it says " Pre-collection check failed because: ". I have configured the SNMP correctly.
3. I have the CAD files for all the maps in our environment but when I try to upload it to Prime it converts it into GIF, so the maps are uploaded as plain image with no knowledge of walls and obstacles.
So we would have to add the walls and obstacles by ourselves. Is there any way it can automatically pick up on the walls and obstacles and thus provide a better way for predicting RF profiles.
All your help is greatly appreciated.

TAC Case! Sounds like a bug to me...
Sent from Cisco Technical Support iPad App

Some question about Cisco Prime Infrastructure

Dear all
I have some question about using Cisco prime Infrastructure:
- Can I show how many user access to one Access Point (AP) ?
- If I can. What is display information of user ? etc Ip address, MAC, username access, name of device (notebook, tablet, phone ..)
- How many time do Cisco Prime Infrastructure refesh user informantion .?
Please help me and send picture about it if you can.
Thank you so much.

Hi,
I don't have the Prime Infrastructure to post you image, but you can simply find all the answers you want on the config guide:
http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.2/configuration/guide/clientmgmt.html#wp1232242
1- You can surely find how many clients associated to a specific AP.
- Informaiton of the client usually includes username, SSID, ip address, mac address, RSSI, device vendor...etc. I don't think it contains the device type (ipad or iphone both appear as apple vendor. it does not destinguish between this and that.
3- The time of the refreshment is configurable. You need to configure the corresponding background task for the poll period. (this is also metnioned in the link above).
HTH
Amjad
Rating useful replies is more useful than saying "Thank you"

Network topology map Cisco Prime Infrastructure

Hi just want to inquire if it is possible to create a network topology map on cisco prime infrastructure's dashboard that will display both wired and wireless devices or do we need another cisco product to accomplish it.
Thanks

At long last, Prime Infrastructure 2.2 was released yesterday (17 December 2014) and now includes the Topology map feature:
"Cisco Prime Infrastructure provides a visual map that allows you to view the physical network topology, including the network devices and the links that connect them. The topology maps have indicators that show the current alarm status of network devices and links. By using the network topology maps, you can easily monitor your network by viewing alarms and viewing the interconnection between the devices." (Link)
I'm migrating a system now and will open a new thread with first impressions.

User Name and Password for Cisco Prime Infrastructure 2.1

Hi all:
I am stuck at the login page of Cisco Prime Infrastructure 2.1.
I have tried using the user name root and its password (when log in with root at Vsphere Client) and also the login user name "before" get into the appliance infrastructure, all cannot work.
Anybody knows what is the default username or password or any way to set the username and password for this Cisco Prime Infrastructure 2.1 website?
Thanks!
tangsuan

Hi Tangsuan,
Following is the documented procedure for password recovery..
In order to modify the GUI root user password, you will need to login to the NCS CLI
as an admin user, and enter the command
"ncs password root password <new password>" (without the quotes)
This should set the web interface root user password :
http://www.cisco.com/en/US/docs/wireless/ncs/1.1/configuration/guide/manag.html#wp1268889
If you have lost your CLI password , try the default logging that is ,
CLI user is admin and not root, so please try logging in as admin with
the password that was set during setup. If that does not work , you need
the install disk that came with the appliance to recover that password.
Follow these steps:
Recovering a Lost Admin Password
If you lose or forget the admin password for NCS appliance, follow these steps.
Step 1 Reboot the NCS appliance with the ISO DVD inserted. The Cisco Prime Network Control
System Welcome screen appears:
ISOLINUX 3.11 2005-09-02 Copyright (C) 1994-2005 H. Peter Anvin
             Welcome to Cisco Prime Network Control System
To boot from hard disk, press <Enter>.
Available boot options:
   [1] Network Control System Installation (Keyboard/Monitor)
   [2] Network Control System Installation (Serial Console)
   [3] Recover administrator password. (Keyboard/Monitor)
   [4] Recover administrator password. (Serial Console)
<Enter> Boot existing OS from Hard Disk.
Enter boot option and press <return>.
boot:
Step 2 Select the desired recovery option, 3 or 4, depending on how you
are connected to the appliance and then follow the prompts.
Thanks-
Afroz
***Ratings Encourages Contributors ****

When is Cisco Prime Infrastructure 2.0 released, and what does 2.0 offer?

We are running Prime Infrastructure 1.3 primarily for wireless management at this point. We have enough licenses to add all our switches, routers, and firewalls, but we're hesitant to do so until 2.0 comes out. While there are some features for backing up and configuring switches and routers, 1.3 still seems pretty limited in regards to non-wireless features. For example, nearly every report in 1.3 is for wireless controllers or AP's, there are no reports I've found relevent for switches and routers. I've read a lot of blogs, cisco posts, and white papers talking about how Cisco Prime Infrastrucure 2.0 will finally consolidate Prime into a truly all-in-one network management suite that can manage the entire Cisco environment. Does anyone know when it's officially being released? Does anyone have an tech sheets on what's new in 2.0, or what its capabilities are? I want to better understand what 2.0 has to offer, when it's coming out, how to upgrade, so I can start planning for the upgrade and eventually importing all our network devices to Cisco Prime for centralized management. Any useful information or links would be appreciated.
Thanks,
Christian

PI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks

Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
    0 Bad SNMP version errors
    14 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    38453185 Number of requested variables
    0 Number of altered variables
    17790703 Get-request PDUs
    20583581 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    38371069 Response PDUs
    13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
Jeremy

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

CISCO PRIME INFRASTRUCTURE 1.2 NCS ERROR

Hi everyone,
can anyone put through on this, i'm having issue starting the ncs server on cisco prime infrastructure 1.2 .below is the message i get when i do show ncs status:
NGPHC-CPR001/admin# ncs status
Health Monitor is running, with an error.
failed to start NCS on startup Health Monitor
Reporting Server is running
Ftp Server is running
Database server is running
Tftp Server is running
Matlab Server is running
NMS Server is stopped.
SAM Daemon is not running ...
DA Daemon is not running ...
Syslog Daemon is not running ...
status
thanks.

Hi Marvin,
Its has never worked. This is the first time i am installing it.
I haved done as you adviced but still getting the same error as stated above.
Please is there another way out.
thanks.

Cisco Prime Infrastructure 2.1 wired client show Wrong port speed.

Similar Messages

Maybe you are looking for