Cisco Prime Infrastructure 2.2 Email frequency (alert reminders)

Hi,
We have deployed a Cisco PI 2.2 and are able to receive emails when alerts are generated in the network, but emails are ony sent once. Is there any way to set the email frequency for alerts? In the case an alert hasn't been cleared in a certain period, to have the PI send another alert notification.
Thanks.

Have you found a solution to this issue? We are having the same issue at our location.

Similar Messages

Cisco Prime Infrastructure 2.0 not showing alerts from switch

Hello,
I have a prime infrastructure 2.0 running at a customer place and the customer now complains that he is not receiving link up/down messages from the switch. When i checked I have seen that if I shut down a port in the switch the prime identifies after a long time, but its not generating an alarm still. How can I fine tune the prime to fix this issue. Please help on this.
Thanks in advance

Hi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work?

Cisco Prime Infrastructure 2.1 error-disable alert

We have a cisco PI 2.1 managing switches and a lot of switchports have BPDUGuard enabled. When occur error-disable , request send email notification to administrator .
By default, when a port of a switch goes down, the Prime generates alarm for that. (this is a problem, because every laptop disconnection will generate alarm for administrator)
Can i change the alert just for error-disable and how to ?
Thanks

Causes of Errdisable
This feature was first implemented to handle special collision situations in which the switch detected excessive or late collisions on a port. Excessive collisions occur when a frame is dropped because the switch encounters 16 collisions in a row. Late collisions occur after every device on the wire should have recognized that the wire was in use. Possible causes of these types of errors include:
A cable that is out of specification (either too long, the wrong type, or defective)
A bad network interface card (NIC) card (with physical problems or driver problems)
A port duplex misconfiguration
A port duplex misconfiguration is a common cause of the errors because of failures to negotiate the speed and duplex properly between two directly connected devices (for example, a NIC that connects to a switch). Only half-duplex connections should ever have collisions in a LAN. Because of the carrier sense multiple access (CSMA) nature of Ethernet, collisions are normal for half duplex, as long as the collisions do not exceed a small percentage of traffic.
There are various reasons for the interface to go into errdisable. The reason can be:
Duplex mismatch
Port channel misconfiguration
BPDU guard violation
UniDirectional Link Detection (UDLD) condition
Late-collision detection
Link-flap detection
Security violation
Port Aggregation Protocol (PAgP) flap
Layer 2 Tunneling Protocol (L2TP) guard
DHCP snooping rate-limit
Incorrect GBIC / Small Form-Factor Pluggable (SFP) module or cable
Address Resolution Protocol (ARP) inspection
Inline power
Note: Error-disable detection is enabled for all of these reasons by default. In order to disable error-disable detection, use the no errdisable detect cause command. The show errdisable detect command displays the error-disable detection status.

Email notification for config deployment jobs in Cisco Prime Infrastructure 1.2 ??

We're upgrading from LMS 3.2 to Cisco Prime Infrastructure ...
In LMS 3.2 we're using netconfig all the time to configure various jobs related to port security
In installing Cisco Prime Infrastructure and working through it's use of templates, I'm having some difficulty finding out how to send out a notification once a configuration job has completed. It's so simple in LMS 3.2 since it's part of the job creation screens.
Any assistance would be greatly appreciated.

HI, Raymond
Just wondering if this problem is resolved?
Thanks!

Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
    0 Bad SNMP version errors
    14 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    38453185 Number of requested variables
    0 Number of altered variables
    17790703 Get-request PDUs
    20583581 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    38371069 Response PDUs
    13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
Jeremy

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Cisco Prime Infrastructure 1.4 SNMP Traps are not converted into Alarms

Hi everybody,
I just configured SNMP Traps on a Cisco Catalyst 3750-x to send to our Cisco Prime Infrastructure 1.4 Appliance.
Now I forced the Switch to send some traps (Power off a Power Supply, Interface errdisable). The only events I see in Alarms & Events on PI is the same information message everytime:
Configuration management event has been recorded in ccmHistoryEventTable.
I think the forced traps should be converted into alarms? Why can't I see them?
Thanks,
Marc

Ok, I started debugging as you said. I get the following output:
Mar 13 09:28:13.711: SNMP: V2 Trap, reqid 11689, errstat 0, erridx 0
sysUpTime.0 = 198609846
snmpTrapOID.0 = ciscoSyslogMIB.2.0.1
clogHistoryEntry.2.1688 = PM
clogHistoryEntry.3.1688 = 5
clogHistoryEntry.4.1688 = ERR_RECOVER
clogHistoryEntry.5.1688 = Attempting to recover from bpduguard err-disable state on Gi1/0/13
clogHistoryEntry.6.1688 = 198609844
Mar 13 09:28:13.737: SNMP: Queuing packet to xx.xx.xx.xx
Looks like the Switch is sending SNMP Traps from the ciscoSyslogMIB. Is this why PI can't show the Traps and convert it into a alarm?
After this test I configured logging (syslog) to the PI. Now the errors are showed but still not converted into alarms. I just want to be notified by email when such errors occurs.
Thanks,
Marc

Cisco Prime Infrastructure 1.2 Error

Hi,
I don't have any experience with Cisco Prime infrastructure. I am getting the below error
Unable to start secondary NCS server PRLPrimeNCS02 [10.140.xx.xx]
Reason: IO Error: could not resolve the connect identifier "wcss1"
Not sure exactly what the error means. Any help much appreciated.
Thanks
Nachi

Hi Scott,
Thank you for your email.
The HA is runing on the Cisco Prime. Runing Cisco Prime on a Virtual machine in VM.
The issue we are experiencing is that the system failed over to the secondary (HA) for unknown reasons. When we failed it back it didn’t fail back properly. Configured Manual failover. Managed to failback to primary but it complained HA was no longer configured.
Tried to remove HA and reconfigure it. The primary removed the HA configuration, but the secondary kept it. Here is some info on the secondary
PRLPrimeNCS02/admin# ncs ha status
[Server] prlprimencs01(10.xx.xx.xxx) [State] Secondary Lost Primary [Failover Type] manual
PRLPrimeNCS02/admin# ncs ha remove
High availability configuration will be removed
Do you wish to continue? (y/N) y
Removing secondary configuration will remove all database information
Do you wish to remove high availability configuration from primary? (y/N) y
Secondary is attempting to remove high availability configuration from both primary and secondary
Requesting primary to remove high availability configuration from both primary and secondary
Successfully removed high availability configuration
PRLPrimeNCS02/admin#
PRLPrimeNCS02/admin#
PRLPrimeNCS02/admin# ncs ha status
[Server] prlprimencs01(10.xx.xx.xxx) [State] Secondary Lost Primary [Failover Type] manual
PRLPrimeNCS02/admin#
And the primary
prlprimencs01/admin# ncs ha status
[State] Stand Alone
prlprimencs01/admin#
Below is the log
Starting Health Monitor as a secondary
Checking for Port 8082 availability... OK
truststore used is /opt/CSCOlumos/conf/truststore
truststore used is /opt/CSCOlumos/conf/truststore
Starting Health Montior Web Server...
Health Monitor Web Server Started.
Starting Health Monitor Server...
Health Monitor Server Started.
java.lang.OutOfMemoryError: Java heap space
Dumping heap to logs/java_pid6044.hprof ...
Heap dump file created [249907589 bytes in 6.857 secs]
Thanks
Nachi

Including Interface Description in Cisco PRime Infrastructure Alarm Message

Hi all,
i succesfully configured a Cisco Prime Infrastructure 2.1 applliance to display an alarm and to send me an e-mail when switch uplink ports goes down.
The text displayed in alarm message is :
port 'interface_id' is down on device 'device_ip_address'
I'd like to include in this text also the interface description so the text will display :
port 'interface_id' 'interface_descriprion' is down on device 'device_ip_address'
Is this possible?
Thankyou in advance

Hi,
i followed these steps :
SWITCH SIDE
- configured Prime Infrastructure as snmp-server host;
- enabled snmp-traps for linkup and linkdown events globally;
- disabled snmp-traps for linkup and linkdown on non relevant interfaces using the no snmp trap link-status command
PRIME INFRASTRUCTURE SIDE
- under "Deploy/Monitor Deployment" i deployed template "Interface Health" for all the interested switches
- under "Administration/System Settings/Mail Server Configuration" configured my internal SMTP server to make Prime Infrastructure able to send e-mails
- under "Operate/Alarms & Events" click on "Email Notifications" , then on "Switches and Hubs"
- check the "critical" box , insert the destination e-mail address into the "To" field then click "Save"
- check the "switches and Hubs" box and then click Save
As i know is possible to avoid to configure every single not-interesting port on the switches with "no snmp trap link-status" command (it's a bit annoying when you have tens of switches), using Port Grouping configuration on PI but i tried it without success.
Hope this helps.
Best Regards,

Consultations on Cisco Prime Infrastructure 2.2

I recently installed Cisco Prime Infrastructure 2.2 and I have 2 questions regarding configuration:
1. What configurations should run for vulnerability when some event occurs on a switch an alarm is lifted in the Cisco Prime Infrastructure 2.2?
2. Is there any way to put a device into maintenance mode in the web interface of Cisco Prime Infrastructure 2.2, so that can not be spoiled reports regarding equipment availability during the execution of maintenance?

1. If you configure PI as an SNMP and syslog server for your devices and have enabled logging traps etc., PI's alarm browser will show the alarms. If you want them to be sent to you via email, you can do that under the Admin menu for setting up your Mail server and clicking the link to "Configure email notification for individual alarm categories." (see below - open in new tab to zoom). It's not completely customizable but what you see there is the current product capabilities in that regard.
2. No, this is not currently an available feature in PI 2.2.

Cisco Prime infrastructure template undeploy

Hi,
I am new to cisco prime, I have create the new Trap receiver template and deployed to one of the wireless controller and saved the deployment
Now I want to undeploy the templates, When I tried undeploying the templates for same wireless controller, I got the warning message stating "Failed to undeploy the template"
Please advice on below points
1. How to undeploy the templates in cisco prime infrastructure
2. Where to find the snmp traps ( steps to check the snmp traps) in cisco prime.
Please Help!!!!!

Using System Logs
Prime Infrastructure logs all error, informational, and trace messages generated by all devices that are managed by Prime Infrastructure.
Prime Infrastructure also logs all SNMP messages and Syslogs it receives.
You can download and email the logs to use for troubleshooting Prime Infrastructure.
Step 1 Choose Administration > Logging. The General Logging Options Screen appears.
Step 2 Choose a Message Level.
Step 3 Check the check boxes within the Enable Log Module option to enable various administration modules. Check the Log Modules option to select all modules.
Step 4 In the Log File Settings portion, enter the following settings. These settings will be effective after restarting Prime Infrastructure.
Note The log file prefix can include the characters "%g" to sequentially number of files.
Step 5 Click the Download button to download the log file to your local machine.
Note The logs.zip filename includes a prefix with the host name, date, and time so that you can easily identify the stored log file. Included in the zip file is an html file that documents the log files.
Step 6 Enter the Email ID or Email IDs separated by commas to send the log file.
Note To send the log file in a mail you must have Email Server Configured.
Step 7 Click Submit.

Cisco Prime Infrastructure 1.3, Mail Configuration

Hi,
I have a Cisco Prime Infrastructure 1.3 and I want to set up the mail. When I test it, I get this error:
Failed to send mail to primary SMTP server. Failed to send mail to secondary SMTP server. Please make sure that you save mail configuration by hitting 'Save' button.
I have the ip address, and the username and password. Do I need to create a new buzon for the prime? because by default the "From" field appears with
[email protected]
Thanks!!

Some extra info that has just come to my attention. At one point we were running (we're actually still running) CiscoWorks with LMS3.2 and Cisco NCS 1.x. I merged these two things together into Cisco Prime Infrastructure (upgraded the licensing to get 450 lifecycle licenses to cover the APs + all of the devices coming from LMS3.2). I followed all of the documented procedures to upgrade the NCS appliance to Prime Infrastructure. But when I type "show application" from the CLI of the NCS appliance (now the Prime Infrastructure appliance) I see this:
HQ-NCS1/admin# show application
NCS Cisco Prime Network Control System
Is that normal? Maybe this is my problem. Should this output list "Cisco Prime Infrastructure" instead of (or in addtion to) Cisco Prime Network Control System? When I login to the GUI it shows "Cisco Prime Infrastructure" and the GUI has changed considerably (menus are different) so I'm assuming that the application upgrades I launched from the CLI to go to Prime Infrastructure worked fine.

Change Interface availability threshold from Cisco Prime Infrastructure 2.0

Dear Community,
I’m working in Cisco Prime Infrastructure 2.0 and I’m having the following problem:
I want to monitor the interfaces availability from all the devices of my network. But only makes sense send an email notification for the most critical interfaces. I don´t want to receive an email notification every time anyone unplugs the network wire.
How can I achieve this?
I already tried to change the interface availability threshold from the Interface Health Threshold Template, but this one isn´t available to configure.
The idea was to change the severity of the alarm so I could distinguish what type of alarm would send email notification.
I also created a Custom SNMP Template that gets the ifOperStatus using the MIB IF-MIB. This also didn’t work because Prime Infrastructure doesn’t allow me to define thresholds to a Custom SNMP Template.
Without threshold, no alarm, without no alarm, no email notification!
Can you help?
Regards,
Daniel CJ

Only on the HA pair which would be the secondary.
High Availability (HA) RTU: If Cisco Prime Infrastructure is deployed in a high availability configuration with one primary and one secondary instance in an HA pair, then an HA RTU is required. You only need to purchase a single set of the regular licenses (for example, Base, Lifecycle, and so on) for the primary instance.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Cisco Prime Infrastructure 1.2 is not working https & ncs

Hi, I have just deploy Cisco Prime Infrastructure 1.2 in a virtual appliance (Vmware Esxi 5.1). Console is ok & setup is also completed. but there is no NCS application. only app is shwoing: NCSPNP
Cannot access from https also.
Please suggest how to Starting Prime Infrastructure Serve

From what you describe, it sounds like you have installed the Plug and Play (PNP) ova image. You need to install the Prime Infrastructure image.
See the screenshot below for details (click to enlarge):

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

• PI provides visibility for autonomous clients within the same list view as lightweight and wired clients (client list page).
• Rogue AP detection for autonomous AP's is not supported (it's supported in CUWN).
• Alarms/events for client authentication issues (e.g. authentication failure) are displayed in PI.
• Config management for autonomous AP's is via CLI template. Config comparison and archiving functionality in PI leverages these same features that were brought in from LMS, so need to defer to others in terms of whether this is a cross-platform feature in PI or is only supported on a subset of platforms. Config comparison/archive is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client sessions, etc.) reports, and there are extensive reports for CUWN

User Name and Password for Cisco Prime Infrastructure 2.1

Hi all:
I am stuck at the login page of Cisco Prime Infrastructure 2.1.
I have tried using the user name root and its password (when log in with root at Vsphere Client) and also the login user name "before" get into the appliance infrastructure, all cannot work.
Anybody knows what is the default username or password or any way to set the username and password for this Cisco Prime Infrastructure 2.1 website?
Thanks!
tangsuan

Hi Tangsuan,
Following is the documented procedure for password recovery..
In order to modify the GUI root user password, you will need to login to the NCS CLI
as an admin user, and enter the command
"ncs password root password <new password>" (without the quotes)
This should set the web interface root user password :
http://www.cisco.com/en/US/docs/wireless/ncs/1.1/configuration/guide/manag.html#wp1268889
If you have lost your CLI password , try the default logging that is ,
CLI user is admin and not root, so please try logging in as admin with
the password that was set during setup. If that does not work , you need
the install disk that came with the appliance to recover that password.
Follow these steps:
Recovering a Lost Admin Password
If you lose or forget the admin password for NCS appliance, follow these steps.
Step 1 Reboot the NCS appliance with the ISO DVD inserted. The Cisco Prime Network Control
System Welcome screen appears:
ISOLINUX 3.11 2005-09-02 Copyright (C) 1994-2005 H. Peter Anvin
             Welcome to Cisco Prime Network Control System
To boot from hard disk, press <Enter>.
Available boot options:
   [1] Network Control System Installation (Keyboard/Monitor)
   [2] Network Control System Installation (Serial Console)
   [3] Recover administrator password. (Keyboard/Monitor)
   [4] Recover administrator password. (Serial Console)
<Enter> Boot existing OS from Hard Disk.
Enter boot option and press <return>.
boot:
Step 2 Select the desired recovery option, 3 or 4, depending on how you
are connected to the appliance and then follow the prompts.
Thanks-
Afroz
***Ratings Encourages Contributors ****

Cisco Prime Infrastructure 2.2 Email frequency (alert reminders)

Similar Messages

Maybe you are looking for