Cisco prime syslog functionality

Hello All,
I have added devices in cisco prime. I can see logging option in cisco prime under Administration > Logging .  I have given one server IP  (10.18.89.43) where I wanted logs to get saved but I am not sure whether prime is acting as a syslog server and if its really collecting those syslog. Also how do I know where its saving those logs on server. (See attached image)
Please help me with exact configuration.

Thanks Marvin for valuable reply. I can see Prime generated syslog message for one of added switch under Inventory > Device Management > Network Audit.
But it was just one message as follows:
Syslog Message<189>92196: Apr 21 17:33:55: %SYS-5-CONFIG_I: Configured from console by 5588648 on vty0 (10.18.83.170)
How do I configure Prime so i can increase buffer for these messages.

Similar Messages

  • Cisco Prime syslog server

    Where are syslogs stored, if I point my devices to Cisco Prime acting as my syslog server? I am running 2.0
    thanks, Jerry

    Hi ,
    As of now , this feature is not available , I mean PI will not work as syslog server.
    Syslog messages received by  PI from managed devices are found under Monitor > Alarms and Events > Syslogs
    as you are using PI 2.2 , you will be able to see all device syslog messages (0-7 severity)
    That display will show you up to 200,000 messages at a time.
    Check the below link for other related details proved by Marvin :
    https://supportforums.cisco.com/discussion/12486126/cisco-prime-syslog-functionality#sthash.Wbj2a3lj.dpuf
    Thanks-
    Afroz
    ***Ratings Encourages Contributors ****

  • Cisco prime syslog alarm

    Is it possible to generate an alarm for especific Syslog Messges sent to Cisco Prime?
    Admin > Network > Notification and Action Settings > Syslog Automated Actions
    Here is possible to send an email. But I would like to see the alarm in the Monitoring dashboard.

    It's a bit kludgey but one of the available automated actions is to run a script. The script could be a homegrown utility to generate a trap which is subsequently forwarded to the server itself. The server will then will parse this new "trap" and then display it on the dashboard.
    See this document for example.

  • Configure the syslog of ASA 5512-X for display on Cisco Prime Infrastructure 2.1

    Hi, I'm working on implementing the Cisco Prime Infrastructure 2.1 and want to display the syslog about ASA5512-X with Software Version 9.2.
    What would be the procedure for configuring?
    Thanks in advance.

    Hi,
    Enable "logging host x.x.x.x "  command to enable logging
    check the below link:
    http://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/monitor_syslog.html#68764
    FYI: Prime Infrastructure support only SEV 0,1,2 syslogs as of now.
    Operate > alarm and events > syslogs
    Thanks-
    Afroz
    ****Ratings Encourages Contributors *****

  • Can Cisco Prime Infra 2.1 work as syslog server

    Hello all,
        Customer want Cisco Prime Infra 2.1 to work as syslog server.  they want to query text in syslog and get raw log file from Cisco Prime Infra.  but when i see in user interface.  I think that it cannot query and search text in syslog.  but i am not sure whether we can get raw log file per devices from Cisco Prime Infra.   Can anyone know about this.?
    thanks
    sompoj

    Hi Sompoj,
    In the prime infrastructure Syslogs are directly read from udp port 514 and then filtered
    , the non SEV1 and SEV2 syslogs will be dropped and will not be entered into db . The
    syslog messages will not be saved into log files .
    Thanks-
    Afroz
    ****Ratings Encourages Contributors ****

  • Syslog Email forwarding on Cisco Prime Infrastructure

    Hi everybody,
    We are performing a migration from LMS 4.2 to Prime Infrastructure 2.1 and we are realizing that some features are not in this new platform.
    I suspect that one of them is syslog forwarding by email. In our old LMS we collect some syslog messages, we filtrate them and we email some of them, based on a criteria. Some of them we email to someone, and some of them are droped.
    Does someone know if this feature is avaliable in Cisco Prime? I think we can collect syslog messages and view them, but we can not process. Am I right?
    Regards and thank you in advance,
    David

    Hi David,
    Yes , unfortunately  so far syslog forwarding is not supported. 
    Also so far only SEV 0.,1 and 2 syslogs are supported in PI. Hoping to have these features in PI 2.2
    Thanks-
    Afroz
    *****Ratings Encourages Contributors ****

  • Is cisco prime infrastructure support / can be run as syslog server?

    Dear All,
    is cisco prime infrastructure support / can be run as syslog server?
    and,
    where i can see network topology diagram, using cisco prime infrastructure?
    many thanks,
    Jerri

    Hello. Cisco Prime LMS will be replaced by Cisco Prime Infrastructure in the near future.
    In the current release of Cisco Prime Infrastructure you can't use topology diagrams. This feature is in roadmap.
    About syslog, you can send syslogs to Cisco Prime Infrastructure, but I don't recommend using it as syslog server. Please see this link for more information https://supportforums.cisco.com/thread/2179520
    Please rate if this helps

  • SYSLOG Cisco Prime LMS

    Hi friends,
    I have a question about my syslog from Cisco Prime LMS 4.1, the hours from this syslog in the LMS is diferent from my switch log.  I dont kown why.. I verified the hours betewen switch y the Cisco Prime is the same(the LMS is over Windows Server 2008R2) . both are the same log but in diferent hours about 5 hours.
    maybe I have to configure the hours for Syslog in the Cisco Prime.
    Log from Switch
    Log from Cisco Prime LMS

    If you have LMS, i am not sure, but if you have PI 1.2. Take a look at my post.
    Basically, syslog feature doesn't work well. I could see couple of syslog through event / alarm, but syslog itself is not working properly.
    https://supportforums.cisco.com/message/3861981#3861981

  • Cisco Prime - create a Fault Alarm for Syslog Messages

    Is it possible to generate an alarm for especific Syslog Messges sent to Cisco Prime?
    Admin > Network > Notification and Action Settings > Syslog Automated Actions
    Here is possible to send an email. But I would like to see the alarm in the Monitoring dashboard.

    Hi Leonardo,
    unfortunately ,Automated action that you create on syslog will not show in the Monitoring dashboard :(
    Thanks-
    Afroz
    ****Ratings Encourages Contributors ****

  • Download devices syslogs of Cisco Prime Infrastructure 2.2

    Hello,
    I'm working with Cisco Prime Infrastructure 2.2, wish I could download to my PC syslog captured by PI.

    Hi ,
    In the prime infrastructure Syslogs are directly read from udp port 514 and then filtered , the non SEV1 and SEV2 syslogs will be dropped and will not be entered into db . The syslog messages will not be saved into log files .
    Thanks-
    Afroz
    ***Ratings Encourages Contributors ****

  • Cisco Prime Soft Appliance not saving changes to syslog.conf

    Greetings,
    I'm having an issue with the syslog.conf file on a Cisco Prime LMS 4.2.4 soft appliance with a Solaris base.  My workplace uses local4 as the logging facility for its network devices, and according to a discussion I found on this site, I need to add the line:
    local4.info  /var/log/syslog_info
    I have attempted this several times; we're approaching at least 5 attempts today.  I have attached text files created from putty logs where I've attempted to make the necessary change.  I appreciate any assistance the community can provide.
    Regards,
    Rob

    Hi, Afroz,
    I really appreciate your assistance, but I'm afraid my hopes have been dashed.  The syslog.conf reverted to its original configuration.  I will go through my steps to be sure that I understood your suggestion properly.
    I edited the syslog.conf to put all messages from local4 in /opt/CSCOpx/conf/syslog-entries.txt.  Then, I exited the shell to the console, issued the 'write mem' command, and closed the session.  Upon my reconnection, I found that my changes to the syslog.conf were not saved.
    Did I make the correct edits in the correct places?  Another question, is this bug present in the versions of Prime LMS running Linux and/or Windows, or does it only exist in the soft appliance running Solaris?
    Regards,
    Rob
    Edit:
    I'm reading the "Installation and Migration of Cisco Prime" PDF, and it gives me the impression that Cisco Prime is only supported as Windows, Solaris, and soft appliance installations.  Is that correct?  If it is correct, then installation of Cisco Prime LMS is not supported on other Linux distros such as Ubuntu Server, CentOS, Fedora, etc.?
    My thanks.

  • Limit Syslog DB size Cisco Prime

    Hi All,
    I have an issue with my Cisco Prime 4.1.
    I have a log file for syslog who’s getting bigger and bigger every day. We have created a purge policy to limit the size to 1 gigabyte. This seamed to be a good solution.
    But at the same time, I have a database located under Cscopx/database/rmeng/syslog.db, in three parties, syslogfirst, second and third. The problem is that those files grow and never stop growing (5GB and more), until the disk space is full.
    At the start the syslog db didn't grow anymore since I configured the purge job for the syslog file. But after a while the syslog db began to grow again.
    Are those 2 (syslog file and DB) related in any way? Does anyone has the same problem? I suppose there is an easy way to limit the size of the syslog db.
    Thanks,
    Best Regards,
    Joris                  

    Syslog.log and Syslog*.db are connected to each other. Syslogs sent from device are received in syslog.log and then processed and written in syslog db. All syslog reports come from Db.
    To control the log file the logrot utility is used and to control the db the syslog purge and other administrative fuctions are used.
    For more details on logrot configuration see :
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/user/guide/admin/server.html#wp1055307
    For details on administring syslog see :
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/user/guide/admin/purgeset.html#wp1060237
    Attached is an Syslog Acrhitecture for LMS, hopefully it will be helpful.
    -Thanks

  • What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

    What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

    • PI provides visibility for autonomous  clients within the same list view as lightweight and wired clients (client list  page).
    • Rogue AP detection for autonomous AP's is not supported (it's  supported in CUWN). 
    • Alarms/events for client authentication issues (e.g.  authentication failure) are displayed in PI.
    • Config management for  autonomous AP's is via CLI template.  Config comparison and archiving  functionality in PI leverages these same features that were brought in from LMS,  so need to defer to others in terms of whether this is a cross-platform feature  in PI or is only supported on a subset of platforms.  Config comparison/archive  is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and  Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client  sessions, etc.) reports, and there are extensive reports for CUWN

  • Web Interface of Cisco Prime 2.1 not working

    Excuse me!
    I install the trial version cisco prime 2.1 (OVA) on ESXi server
    I can ping cisco prime but web interface of cisco prime not worinking
    prime/admin# ncs status
    Health Monitor Server is running.
    Ftp Server is running
    Database server is running
    Tftp Server is running
    Matlab Server is running
    NMS Server is running.
    Plug and Play Gateway is running.
    SAM Daemon is running ...
    DA Daemon is running ...
    Syslog Daemon is running ...

    Services running fine..
    check it with other Browser , Supported browser are below::
    –    Google Chrome 31 or later.
    –    Microsoft Internet Explorer 8.0 or 9.0 with Google Chrome Frame plugin (users logging in to the simplified Lobby Ambassador interface do not need the plugin).
    –    Mozilla Firefox ESR 24.
    –    Mozilla Firefox 24, 25 or 26.
    If above does not help , reboot the server once and check the issue again.
    Thanks-
    Afroz
    ***Ratings Encourages Contributors ****

  • Cisco prime infrastructure not detect IP address of clients

    hi all,
    I have Cisco Prime infrastructure 1.2 and when move to monitor >> clients tab it lists me all the clients in my network but their IP address list estates "not detected" ?
    please any advice?
    I appreciate your kindly support.

    Just an update that while this appears to have worked fairly well (as far as Cisco Management Planes go), there was one small 'gotcha' I've noticed so far:
    After the services came back up, the entries for our RADIUS servers did not function.  No, not because I didn't update the clients address record on the RADIUS server itself, but because the RADIUS server record(s) within CPI have a field called 'Local Interface IP' that still reflects the previous IP assigned to CPI.  A quick edit/save with the new interface fixes up the issue however.
    Cheers!

Maybe you are looking for

  • Unable to unistall Cisco AnyConnect VPN - please help

    I have upgraded to Windows 8.1 preview on my Surface Pro. My Cisco AnyConnect VPN stopped working. When I uninstalled the software it left the 'Cisco AnyConnect VPN Virtual Miniport Adapter for Windows x64' under the network adapters in Device Manage

  • Misconception about the LAG function's ... functionality?

    So I want to look at the value of a column on a current row, and the value of the same column on the most recently entered row, prior to the current. The problem I'm encountering is that for the current row, I'm only interested in those added last mo

  • When will Maverick Graphic Issues be fixed

    Boy is Maverick a proble, Socend screen flickers, other have reported this for months. I'm doubting Apple as Maverick has been a disaster personally. Graphic patch? ... maybe this year?

  • Deleting previous versions of iPod and iTunes software

    I'm trying to clean house. Is it safe for me to delete the older versions of iPod and iTunes software that are on my C drive? I would probably die if I lost or misplaced my music files! Thanks.

  • Transaction Datasource Enhancement

    Hi Experts, I did the extractor enhancement for 0WBS_ELEMT_ATTR. Data will be loaded to an infocube using infosource 0CO_OM_NWA_1. Do I still need to enhance the transaction datasource to populate data into a infoobject related to WBS element? Please