Cisco Prime v2.2 and Catalyst 6509 SNMP "time out"

Good afternoon,
I have PI v2.2 up and running and my v2.1 data restored. Went very smoothly. I have all my WLC's added and re-sync'd, but when I'm trying to re-sync my 6509s, I'm getting an SNMP Connectivity Failed.
It states that the possible cause could be "SNMP request timed out. Verify device credentials and SNMP response speed from device."
I have verified the SNMP credentials, and they are correct.
Any ideas/suggestions?
Thanks,
John L.

Hi!
Same problem here! We upgraded to v2.2 and after that we have had difficulties with 6509 with IOS 12.2(33)SXJ7. Catalyst 6009 and 6506 are both ok. Only this one says " "SNMP request timed out. Verify device credentials and SNMP response speed from device."
We have checked SNMP credentials and increased time-out value to 20 with no effect.
Is this again a product which has not tested with older switches at all...?
br, Matti

Similar Messages

Ask the Expert: Overview of Cisco Prime Service Catalog and Process Orchestrator Solutions

Welcome to this Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the Cisco Prime Service Catalog and Process Orchestrator solutions.
Cisco expert Jason Davis will discuss Cisco’s network management products offered under the Cisco Prime framework. If you have questions about Cisco Prime infrastructure or data center automation with our Cisco Prime Service Catalog and Process Orchestrator solutions, join us on the Cisco Support Community.
Jason Davis is a distinguished services engineer in the Intelligent Infrastructure Practice team of Cisco Advanced Services. His role is to provide strategic and tactical consulting for hundreds of Advanced Services customers, lead service innovation, and assess new services and technologies. Jason's primary expertise areas are in network management systems, intelligent automation, virtualization, data center operations, software-defined networking, and network programmability.
Based out of the Research Triangle Park (RTP) campus, Jason is also responsible for administering the Research Triangle Park Network Management Lab, Cisco's largest network management lab.
Since joining Cisco in 1998, Jason has been a frequent speaker at Cisco's Networkers and CiscoLive conferences in the United States and Europe. In the past five years he has also been involved in the conference network setup and monitoring. He is a much sought-after resource by the field sales teams to assist with presales solutions and executive briefings. He has provided strategic and tactical network management consulting for several hundred customers.
Jason is a subject matter expert with the following products and features:
Cisco Prime LAN management solution
Cisco Prime infrastructure
CiscoSecure ACS
Cisco Prime Network Registrar
Cisco Process Orchestrator
Cisco Prime Service Catalog
Cisco IP SLA
Embedded Event Manager
SNMPv3
onePK and OpenFlow
Cisco UCS
Device instrumentation
VMware ESX, ESXi, and vCenter
ITIL
Jason received his bachelor of science degree in electrical engineering from the University of Miami (FL). He has been married for 20 years and has 4 children. His interests include providing audiovisual technical support for churches and conference venues, camping and biking with his family, remote-control helicopter piloting, paintball, and recreational shooting.
Remember to use the rating system to let Jason know if you have received an adequate response.
Because of the volume expected during this event, Jason might not be able to answer every question. Remember that you can continue the conversation in Data Center > Intelligent Automation under the subcommunity Cisco Prime Service Catalog shortly after the event. This event lasts through September 12, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hello Jason,
Thank you very much for welcoming me to your expert discussion :) I feel to be in the right place, at the right time. Thank you also for answering question beyond your scope here, much appreciated. The information received will help me to go further as such I have submitted a 5 start rating for your first reply.
That sounds promising about the LMS part so yes, I stay tuned and wait patiently.
Ok, now let’s revert to the actual topic discussed here. Cisco Prime Service Catalog and Process Orchestrator solutions I have briefly read up on this on CCO (where elseJ) and picked out the following quote
---- Quote from the Cisco Prime Service Catalog Data Sheet
Today’s end users want self-service and easy access to IT tools and services.
Simultaneously, organizations are seeking ways to extend their cloud management
platforms beyond self-service delivery of virtual machines and infrastructure resources
while increasing their use of cloud-based solutions to enhance business agility and effectiveness.
Cisco Prime™ Service Catalog offers tremendous benefits to organizations that want to unify the ways in
which all types of IT services are ordered and fulfilled, not just infrastructure requests
---- un quote ---
I try to understand what (at high level of course) happens in the back ground when an order is raised and which vendor solution your product can interact with.
As mentioned in the quoted text, this service catalogue goes beyond the standard infrastructure.
Let’s say, a user wants to deploy a new email services, or in your example, extends or create a new web-portal (i.e. for HR to view and manage holiday, staff absence and benefits).
Your solution will need to interact somehow with the 3rd party vendor application that is capable building such portal I believe.
Without disclosing to many information, I assume the portal is linked to backend VM,s that spin up requested resources (and more magic of course). Perhaps I am mixing this up with another cisco product where a user can go on the portal and spin up virtual Firewalls, virtual Routers can be provisioned in now time.
Out if interest; Is this product also known as Mozart? (project code within Cisco?)
I hope query is ok.
Best wishes
Markus

When downloading 10.5.2 version of itunes to Microsoft Vista 32 bit it gets to 68% downloaded and hangs then eventuall times out. No error msg given. What is it waiting for?

When downloading 10.5.2 version of itunes to Microsoft Vista 32 bit it gets to 68% downloaded and hangs then eventuall times out. No error msg given. What is it waiting for?

Finally got it working, I had to delete two solitary files in an iTunes folder.
C:\ProgramData\Apple Computer\iTunes\SC Info
Delete the only two files that are in this folder. Please note that it is a hidden folder.
After they have been deleted, iTunes should work (it did for me)
This may not work if your iTunes.exe process (viewable with task manager) turns off after the license agreement. I solved that problem by updating quicktime.
iTunes 10.5.2 doesn't update quicktime like all the previous installers did.

Hi, every time i try downloading ios5 it reaches 100% and then the connection times out and nothing happens after that; though the internet connection is fine as i can access other sites etc. what could be the problem?i tried using 2 different modems.

Hi, every time i try downloading ios5 it reaches 100% and then the connection times out and nothing happens after that; though the internet connection is fine as i can access other sites etc. what could be the problem?i tried using 2 different modems. Where can i download the ios5 from as my itunes is on my desktop which uses windows xp. Please help

Download iOS 5.1
iOS 5.1 (build 9B176) is compatible with iPad 1, iPad 2, iPhone 3GS, iPhone 4, iPhone 4S, iPod touch 3rd & 4th gen, and iPad 3. Additional builds are available for Apple TV 2 and Apple TV 3. The below download links are all direct downloads of iOS 5.1 from Apple.
iPad 1
iPad 2 Wi-Fi
iPad 2 GSM (AT&T)
iPad 2 CDMA (Verizon)
iPad 2,4
iPhone 3GS
iPhone 4 GSM (AT&T)
iPhone 4 CDMA (Verizon)
iPhone 4S
iPod touch 3G
iPod touch 4G
iPad 3 Wi-Fi
iPad 3 GSM
iPad 3 CDMA
Apple TV 2 (9B179b1)
Apple TV 3 (9B179b1)
Source: http://osxdaily.com/2012/03/07/ios-5-1-download/

Ask the Expert: Cisco Prime Infrastructure - Implementation and Deployment

Welcome to the Cisco Support Community Ask the Expert conversation.
This Ask The expert Session will cover questions spanning Cisco Prime Infrastructure on Implementation and Deployment on Wired and Wireless. This will be more specific to Customer’s and Partners questions product covering PI on configuration, Features and Menu, Network Monitoring, Maps, Implementation, High Availability and Maintenance and t/s parts.
Monday, February 2nd, 2015 to Friday, February 13th, 2015
Dhiresh Yadav is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco Prime Infrastructure and Cisco Wireless products. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS) and CCIE (DC) certifications.
Afroz Ahmad is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS),CCIE (DC), and SCJP (Sun Certified Java Professional )
Vinod Kumar Arya is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 8 years of industry experience working with large enterprise and service provider networks. He also holds VCP 5 and RHCE certifications.
** Remember to use the rating system to let the experts know you have received an adequate response.**
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure community, > Network Management, shortly after the event. This event lasts through February 13th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.

Hello Wilson,
Thanks for joining us.
1841 should just work fine for net flow . Hope you have a valid "PI Assurance license" installed on the server.
"PI Assurance license" is required for "net-flow" feature
Devices supporting Netflow in PI ::
1400, 1600, 1700 & 1800
2500, 2600 & 2800
3600, 3700, 3750 & 3800
4500 & 4700
AS5300 & 5800
7200, 7300, 7400 & 7500
Catalyst 4500 ASCI
Catalyst 5000, 6500, & 7600 ASCI
ESR 10000 ASCI
GSR 12000 ASCI
Cisco IOS Software Release Version
Supported Cisco Hardware Platforms
11.1CA, 11.1CC
Cisco 7200 and 7500 series, RSP 7200 series
12.0
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series
12.0T, 12.0S
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8600 series
12.0(3)T, 12.0(3)S
Cisco 1720, 2600, 3600, 4500, 4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)T
Cisco 1400, 1600, 1720, 2500, 2600, 3600, 4500,
4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)XE
Cisco 7100 series
12.0(6)S
Cisco 12000 series
NetFlow is also supported by these devices Cisco 800, 1700, 1800, 2800, 3800, 6500, 7300, 7600, 10000, CRS-1 and these Catalyst series switches: 45xx, 55xx, 6xxx.
NetFlow export is also supported on other Cisco switches when using a NetFlow Feature Card (NFFC) or NFFC II and the Route Switch Module (RSM), or Route Switch Feature Card (RSFC). However, check whether version 5 is supported, as most switches export version 7 by default.
You can check the below steps to diagnose the issue::
To verify that NetFlow is exported from a device to PI, follow the steps below:
1)   Browse to Administration > Data Sources page. Check the value in column ‘Last Active Time’ for the ‘Device Data Sources’ table. If the table is empty or the value does not represent recent time, then
it is possible that the device is not exporting NetFlow or PI Assurance license is not applied / expired.
2)   Login to PI console ( via SSH) as root user and run the command:
                netstat –an | grep 9991 – Output of this should be like : udp        0      0 :::9991         :::*
                Check the firewall settings on PI server using the command: firewall -L
1)   Check the configuration on an IOS / IOS –XE device. Run the commands
a)   sh running-config | inc destination
1)   This should list the IP address of the PI SERVER ( along with other outputs if any)
b)   sh running-config | inc 9991
1)   This should list at least one entry.
c)   If the above are fine, then verify that the flow monitor, flow exporter and the flow records are correctly configured on the device.
Refer to the URLs below to configure NetFlow export.
http://preview.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_monitor.html#wp1056427
Thanks-
Afroz
***Ratings Encourages Contributors ****

What is the difference in the features between Cisco prime 1.2 and Cisco prime 1.4 ?

Dears,
Please i need to know what is the difference in the features between Cisco prime infrastructure 1.2 and Cisco prime 1.4.
Already i see the release note for each one but the release indicate only the New feature for every one. so i need to know the difference between them not new features.
Wait your kind feedback plz
Regards,

Hi,
New Features and Enhancements
The following topics describe new features and enhancements in Cisco Prime Infrastructure 1.4.
Management Support for WLC Release 7.5
Support for 802.11ac Module
Support for Cisco AP 700
Policy Classification Engine
FlexConnect Audit Support
Autonomous AP Support
Client Stateful Switchover
Cable Modem Monitoring
Support for Secure File Transfer Protocol
and please go through the link and check the data sheet for further clearance.
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/datasheet-c78-729879.html

Cisco Prime 1.2 and image management

Does Cisco Prime 1.2 have the ability to work with image management? I was told yes but I do not see the options and I have verified I have the correct license...

Hi,
Go to Operate > Device work Center > software Image Management
check the below link:
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.2/user/guide/maint_images.html
Thanks-
Afroz
[Do rate the useful post]

Cisco Prime 2.0 and monitoring FWSM transparent context

Hi All,
We have FWSM and ASASM configured in mixed mode (routed and transparent) In transparent mode, there is no IP address linked to the interface.
Cisco Prime save just the admin context, not the global context and other context.
My question is: how to save multiple context using Cisco Prime when context are configured in transparent mode? .
Rgds
Silvere

Omer,
"You can schedule when Prime Infrastructure collects the configurations of selected devices and specify recurring collections by choosing Operate > Configuration Archives , then clicking Schedule Archive ."
The quote is from the User Guide.
Hope this helps.

I have a VSS failure and two 6509 were all out of work.

Hi,
      standby 6509 sup in VSS crashed, and remain in rommon status and hadn't come back untill we reload it on the moring,
      but we found active 6509 shutdown all it's MEC interfaces , and standby 6509 remain in rommon status,so we run into a totoally out of work situation untill we reload standby box on the morning.
     customer lost communication for almost 8 hours, because fail happened at middle night.
     is there any mechanism like VPC auto recovery to config on VSS.
    this is ridiculous , because we have one full function 6509 but lost all communication in this failure.
     how can i avoid this , we config VSL and fast hello dual-active detection. but can't recovery automactilly from this fail
    another question: cisco support community change it's web page i can't find my post.
     thank you!
Tom

HiHi
Thank you
    two 6509 VSS, has one interface each box connect a layer 3 swtichA through portchannel. I found two interface on switchA also down and nerver come on until we reload standby 6509, and ospf neighbor to this switchA was also down.
    we config two tengigabit eth interface on diifferen line card as VSL, and two gigabit interface as fast hello dual-active detect interface.
   found log as below from active 6509
   but custmer didn't check active 6509 status and reboot standby 6509 directly to recovery.
    I think active 6509 shutdown it's interface and standby 6509 remain in rommon status, two 6509 all were out of services , so everything were lost for 8 hours.
    I think during standby 6509 crash( i can find crash file to to memory parity error), there is little time , active 6509 still can detect dual active through fast hello, so active 6509 shutdown it's interfaces, but unfortrunately standby 6509 reamin in rommon status, two box were out of work at same time.
    if standby 6509 are totally down(or crash,or power down) , does actice 6509 shutdown interfaces?( I think this is not correct behavior, active 6509 should keep working?)
    if active 6509 are totally down( or crash), does standby 6509 take over,
    If my thoughts is correct, this is rididuculous, because i can't avoid whole standby 6509 crash or power down.
    but if standby 6509 is down, how can active 6509 know standby 6509 is down or VSL and dual-active detect interface are all down to avoid dual active.
   is there any possible to find a way: if standby 6509 is down or crash , active 6509 can detect this is not a dual active,and remain working.
if VSL and dual active detect interface are all down, two 6509s can detect this dual active and active 6509 shutdown it's interface
thank you!
Tom
LL to DOWN, Neighbor Down: Interface down or detached
Mar 17 23:31:27.440: SW1_SP: Switch 2 Physical Slot 1 - Module Type LINE_CARD removed
Mar 17 23:31:27.939: SW1_SP: Switch 2 Physical Slot 3 - Module Type LINE_CARD removed
Mar 17 23:31:28.175: SW1_SP: Switch 2 Physical Slot 8 - Module Type LINE_CARD removed
Mar 17 23:31:28: %SATVS_IBC-SW1_SP-5-VSL_DOWN_SCP_DROP: VSL inactive - dropping cached SCP packet: (SA/DA:0x4/0x4, SSAP/DSAP:0x18/0x0, OP/SEQ:0x320/0x66AF, SIG/INFO:0x1/0x501, eSA:0000.0500.0000)
Mar 17 23:31:29: %OSPF-5-ADJCHG: Process 2011, Nbr 10.218.96.51 on Vlan181 from FULL to DOWN, Neighbor Down: Interface down or detached
Mar 17 23:31:29.163: SW1_SP: Switch 2 Physical Slot 9 - Module Type LINE_CARD removed
Mar 17 23:31:36: %VSDA-SW1_SP-3-LINK_DOWN: Interface Gi1/1/23 is no longer dual-active detection capable
Mar 17 23:31:36: %VSDA-SW1_SP-3-LINK_DOWN: Interface Gi1/1/24 is no longer dual-active detection capable

I can't download update 5.0.1 and have disabled all security measures and the download still times out shortly after beginning the download. All other downloads are successful so I know the problem is not in the computer. Can anyone help?

Can't download update 5.0.1 to my iPad2. I disabled all security items in fact have deleted them from computer, but the download still times out advising check settings but all is set right? Can any one help with this matter?

I'm still experiencing this problem. I went to settings, general, software and it says Install now. But when I try, I get an error message.

HT1918 I can't get into my account in iTunes using my ID and password -the session times out after trying to Review and I choose United States as country of origin-- have tried six times and same thong happens. Just want to verify if/which card is being

I can't find out if there is a credit card already attached to my apple ID and password. Every time I go into iTunes, as apple instructs me to do, I can't get into "Review", as it "times out" right after choosing the "united States" for the country of origin. Every time. All seven times now. I received this phone as a gift from my wife and she can't remember if there was a credit card put on file, but thinks there was, since she's pretty sure they wouldn't let her set up the apple account for the new phone without it. You would think that this should be easy to find with my ID and password and security info and all, but after almost an hour, we are at our wit's end!! Please help!!! THANK YOU!!!

I have the same problem too and tried alot of things like time zone , restarting or changing DNS of wifi connection to 8.8.8.8 still nothing happens .. !!
iPhone 5s, iOS 8.3

After starting up, it seems to get slower and slower until it times out

It starts up fine, but then it gets slower and slower until it either freezes or it times out.

Try to boot up in safe mode by holding the shift key down when the computer starts up:
http://support.apple.com/kb/HT1564

Activation / Supending of Trial for ABAP on HANA and BW 7.4 time out

Hi altogether,
until today, the CLOUD solution ABAP on HANA and Netweaver BW 7.4 on HANA worked perfectly.
But today (22/01/2015) I get either Time-out Problems when activating or supsending.
Currently one instance is active and is not suspending. Error message: Suspending did not complete in 1200s. Could you please invest the reason?
Regards,
Jürgen

Hi Juergen,
According to Error Codes - Amazon Elastic Compute Cloud the description of IncorrectInstanceState is:
The instance is in an incorrect state, so the requested action can't be completed. For example, some instance attributes, such as user data, can only be modified if the instance is in a 'stopped' state.
If you are associating an Elastic IP address with a network interface, ensure that the instance that the interface is attached to is not in the 'pending' state.
Could you check for errors in the AWS management Console or contact Amazon?
Best regards,
Stanimir

I bought one several months ago. it sits beside my macbook pro. my macbook pro logs onto itunes successfull, but the appletv will not. when i enter my user name and password, it simply times out?

while my macbook pro will log on successfully to itunes, the appletv times out every single time and i cannot log on.

while my macbook pro will log on successfully to itunes, the appletv times out every single time and i cannot log on.

Cisco prime Changing the password lenght for snmp authentication

When i try and put in passwords for the snmp for authorisation and privacy i find that prime infrastructure
wont accept less than 12 characters
How can i change this setting please
It under Configure/switches/(switch)
Steve

When you run the validation job you can capture the traffic via the packet capture utility in device center.
Be sure to filter only to the device being tested or else you will get a really big tcpdump (jet file).
You can open the resulting jet file in Wireshark to look at the transfer deciphered. That will show you exactly what commands are being sent and what reply comes back from the device.

Cisco Prime v2.2 and Catalyst 6509 SNMP "time out"

Similar Messages

Maybe you are looking for