Cisco Proxy Server/ CSCP?

What is the different between Cisco SIP Proxy Server and Cisco CSCP-Edge Proxy?
Can Cisco SPS work with presence server.

The Cisco? SIP Proxy Server is a software application that provides call-routing services in an IP telephony network. Using the Cisco SIP Proxy Server, service providers and enterprises can create large-scale, highly reliable packet voice networks.
Cisco CSCP-Edge Proxy (CSCP-EP) provides the edge adaptation of SIP signaling for diverse access networks, enabling seamless interoperability between multiple access locations and core network services and resources. The CSCP-EP provides user authentication, signaling compression, QoS signaling for access networks, security, STUN for Network Address Translation (NAT)/Firewall traversal and other adaptation functions. The CSCP-EP maps to the Proxy CSCF (P-CSCF) in the 3GPP IMS specification.
try these links:
http://www.cisco.com/en/US/products/sw/voicesw/ps2157/products_data_sheet0900aecd800f3968.html
http://www.cisco.com/en/US/products/ps6562/products_data_sheet0900aecd80396990.html

Similar Messages

  • Cisco AP1242ag-a-k9 - Proxy Server

    Hello,
    I have a cisco AP1242AG-A-K9, I would like to set it up to connect to a proxy server inside of the US.  Does anyone know if this is possible?
    I would like my IP Adress through the router to be a IP Address based in the states, thus the proxy server would achieve that.  I can do this on my PC, but I would like my router to do it, then all the devices on the network to do that.
    Thanks,

    Hello Eliott,
    AP1242AG-A-K9 is not a router. It is an access point.
    You can not achive what you want to do via the AP. You need to setup proxy config on the clients themselves. There is no proxy server optoin can be configured on this AP.
    Regards,
    Amjad
    Rating useful replies is more useful than saying "Thank you"

  • Cisco 4507R WCCP with blue coat SG 8000 as proxy server integration

    Dear All,
    I installed the blue coat on one of the vlan with users in diffwrent vlans. The core 4507R is used with L3 vlans as gateway for the respective vlan users. Now i need to configure both core switch and blue coat as proxy server so that all the users in different vlans access internet websites without configure the blue coat proxy address but the core switch would redirect the users request to the blue coat proxy server. I tried with latest IOS upgrade to the switch eventhen i could not get the cmds related to WCCP blue coat documents suggest to use in core switch to configure the proxy server of SG8000
    Could any one help me to solve this issue.
    Thanks
    swamy

    Following link may help you
    http://www.cisco.com/en/US/products/hw/switches/ps4324/products_configuration_guide_chapter09186a008062cfc6.html

  • Cisco ime using local proxy server

    folks
    i've a strange process going on
    ime can't connect to any of my sensors and when i run a packet capture it looks like its using an old proxy server i had configured some time ago
    i've checked that IE isn't configured for a proxy but can't find where ime is picking it up from
    anyone any ideas?
    thanks                  

    Hello Sr,
    I can ensure you that there is one proxy between the IME workstation and the IPS sensors, it might be taking it from the Java setup.
    This of course might cause you problems while attempting to connect to the sensors,
    What are the work-arounds/solutions for this:
    1)Create an exception rule on the Proxy server
    2) Remove the Proxy server
    3) Try to connect from a workstation that does not go through that Proxy-server
    4) Go to Control Panel > Java > General > Network Settings - Select direct connectio
    Remember to rate all of the helpful posts, that is as important as a thanks
    Julio Carvajal

  • Unable to use proxy server with MAC OS X Anyconnect client

    Hi All,
    I have a VPN setup thru a Cisco 5520, Windows clients connect just find and the end users configure there browser to use our internal proxy servers.   Users with the MAC OS X Anyconnect client can connect, they configure their Mac to use our proxy server, but the broswers will not work, clients can reach networks and resources behind the VPN gateway and have access to the Proxy(Tried a telnet to that hostname/port).  Anyone run into this issue before?  I am running ASA 8.3(2), Anyconnect(OS X) 3.1.01065.
    Thank You

    We had the same problem.
    We are behind government firewall so I don't know which Cisco firewall is used but we are using AnyConnect to establish VPN from internet to LAN behind firewall. We have no problems with Windows. With Mac OS X connection through proxy didn't work with Safari and Chrome (both are using system Proxy setting), but it did work with Firefox (which has it's own Proxy).
    Finally we found out that ethernet MTU size was the culprit. When we set it to manual, with size being 1347 (or less), proxy started to work.

  • LMS 4.2 Device Update without a proxy server

    I'm running LMS 4.2.2, and when I try to initiate a device package update via the webinterface, it fails because I do not have a proxy server configured.  Is there a way to tell LMS that I don't want it to use a proxy?  I have my cisco.com creds in place, and the proxy fields left blank, but it tries anyway, and I can't find anywhere to tell it to ignore the proxy.

    I solved this myself, it seems I had my DNS entries on the Soft Appliance entered incorrectly, so it threw a "cannot find proxy" rather than "cannot resolve hostname" error.

  • OS X Snow Leopard server, proxy server stopped working.

    Hi All,
    I have OS X  Snow Leopard Server (10.6.8) configured as a forward proxy server.  It was working fine for a year until today.  I cannot access any external web sites and get the following error:
    Service Unavailable!
    The server is temporary unable to service your request due to maintenance downtime or capacity problems.  Please try again later.
    If you think this is a server error, please contact the webmaster.
    Error 503
    www.apple.com
    Sun Jul 27 22:53:18 2014
    Apache/2.2.24 (Unix) mod_ssl/2.2.24 OpenSSL/0.9.8y
    If I change the proxy configuration on the Mac client (MacBook Air) to access the Internet directly (bypass the proxy server) all websites work fine.  In the Server Admin, Web, logs I see the following errors:
    Access /var/log/apache2/access_log.
    "GET http://www.apple.com/startpage/HTTP/1.1" 503 1062
    Error /var/log/apache2/error_log.
    [error](60)Operation timed out: proxy:HTTP:attempt to connect to 2.16.236.183:80(*) failed.
    I have tried the following but made no difference:
    -Stop/Start the Web Server.
    -Restarted the Server completely.
    -Uninstalled/Reinstalled the Web Server (Off/On).
    -Reconfigured the forward proxy settings.
    -Empty the proxy cache folder.
    -Checked the files exist under /etc/apache2 folder.
    -Checked the files exist under /var/log/apache2 folder.
    -Checked the the proxy_module and ssl_module are enabled.
    Any ideas and how to troubleshoot this issue further is most appreciated.
    Thanks in advance.

    I think I have fixed it.  I have reloaded/restarted the Cisco router/firewall back end and front end now proxy is working again.  Very odd since I use the same devices to connect directly to the Internet without the proxy server.  Oh well, it's working again so it's all good.

  • Proxy server is refusing connection. Can not open Firefox to scan for problem

    I keep getting an error message: "Proxy server is refusing connection."
    I can not access Firefox due to this message.
    I went to Firefox site and ran the diagnosis scan with no success to clear symptom.
    Running Windows 7 Home premium
    I have Mcafee virus protection.
    I have not knowingly connected to a proxy server.
    I have two PC's running on a Cisco Systems router and the other PC is not having this symptom.

    If you do not need to use a proxy to connect to internet then select "No Proxy"
    See "Firefox connection settings":
    * [[Firefox cannot load websites but other programs can]]

  • Cisco html server error

    I have enabled the http server function on my cisco router. When i log in and try to access the "monitor the router" weblink at any priviledge level, i get "The Page cannot be displayed Error" message. The webpage is "http://172.16.62.69/level/15/exec/-"
    The remaining weblinks work fine. Any help would be greatly appreciated.
    Thanks in advance!!

    Following steps may help you:
    1-If you can see just SOME web pages:
    a.Check the MTU size in your configuration. If the MTU size is too big, the packets may get lost and that will cause the problem with the pages. I suggest you to lower the value, and try to browse.
    2-If you can not see ANY web page:
    a.Make sure you are not using a firewall. If you are using a firewall, make sure it is correctly configured to let the Internet explorer connect to the Internet.
    b.If you are not using a proxy server, make sure that the proxy server options on the LAN SETTINGS from the Internet explorer are not checked. Moreover, if you are using a proxy server, make sure that those settings are pointing to the correct server.
    c.You cal also check the security settings from the internet explorer. You may also want to set the privacy setting to accept all cookies, so all pages will be normally displayed.
    d.Try to browse by IP. In the address bar from the Internet Explorer give the IP address of some website. If you can see the page by IP then the problem is related to the DNS servers. Set the DNS servers that your ISP gave you on the routers configuration.

  • Guest Wireless traffic redirect to Proxy Server

    I have Guest WLAN and i want to redirect all the traffice to Proxy Server. We use Cisco Ironport.
    Cisco proxy Ironport has the ip 10.X.X.X.
    We also have NCS Server. Can anybody tells me where i can configure this
    best regards and thanks in advance

    Muzaffar:
    If you have web-auth configured you may have problems with the redirection if the users are using manual proxy server configured.
    For that, you better enable WebAuth proxy redirection on wireless controller.
    Here is the config example
    http://www.cisco.com/en/US/products/ps10315/products_configuration_example09186a0080b8a909.shtml
    HTH
    Amjad

  • CE-505 w/Microsoft Proxy Server Authentication

    Recently installed Cisco CE-505 and the customer wants to direct everything to Microsoft Proxy Server for authentication and URL filtering with SurfControl. I added the command: http proxy outgoing host 192.168.90.2 80 primary - which directs all HTTP requests to the Proxy Server; however, the proxy server requests a login. Is there a way to pass either a plain text username and password or how to pass the original login information to the Proxy Server. The only way I know how to get around the problem is to policy route the traffic to the inside interface of the Proxy Server.
    Thanks,
    Brian

    Since there has been no response to your post, it appears to be either too complex or too rare an issue for other forum members to assist you. If you don't get a suitable response to your post, you may wish to review our resources at the online Technical Assistance Center (http://www.cisco.com/tac) or speak with a TAC engineer. You can open a TAC case online at http://www.cisco.com/tac/caseopen
    If anyone else in the forum has some advice, please reply to this thread.
    Thank you for posting.

  • ATA 186 behind windows Proxy Server

    Hi Friends, i have been using Cisco ATA boxex behind Cisco routers and they work really fine. Is it possible to configure this box behind a Windows Proxy Server with a Dial-ip configuration? I know the configuration will be difficult due to NAT and H323 issue.. but any of you Experts can guide me Technically I will really appreciate..
    Thank You.
    Sandeep

    I feel now it's possible. Please refer the following link for more information.
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/prod_release_note09186a0080109764.html#47964

  • ACE SSL initiation via Proxy server (squid)

    Hi,
    is it possible to configure ACE with SSL initiation if the connection goes via http/https proxy (squid) ?
    I mean local host is requesting http://xyz.com, ACE doing SSL and requesting https://xyz.com, not directly but via http/https proxy server (squid).
    Thanks

    Hi Ryszard,
    Yes, ACE can initiate SSL traffic and maintain SSL connection. So in SSL initiation ACE will act as a CLIENT receiving clear text HTTP traffic at the front end and sending traffic encrypted over the backend.
    For more details please visit the below link and let me know if you have any questions.
    http://www.cisco.com/c/en/us/td/docs/interfaces_modules/services_modules/ace/vA5_1_0/configuration/ssl/guide/sslgd/initiate.html#wp1010343
    Regards,
    Kanwal

  • How to setup CSS as reverse proxy server without cache server

    Hi, question regarding CSS capabilities.
    Is there a way to setup CSS (11000 series or 11500) to act as a reverse proxy server without caching server in place? Or is it possible for CSS to cache contents on its own?
    And what is disk space on CSS used for?
    Thank you.

    Thank you for clarification on disk usage on CSS. I have gone through sample config for reverse proxy caching
    http://www.cisco.com/warp/customer/117/CSS_CEreverseproxy.html
    Does this mean only way to have CSS to do reverse proxying is to have cache engine in conjunction with CSS?
    Thank you again in advance.

  • Sip Proxy Server

    do somebody know if there is a way to get a demo/test license key for SPS?
    I would like to test it before buy it ( it's not so inexpensive )

    1. The calls supported on Cisco Sip Proxy Server is upto 150 cps. The call rate can exceed 150 cps provided the SharedMemorySize is increased according in the sipd.conf file on both the Linux and Solaris.
    2. I dont think, the number of phones should be an issue with SIP Proxy server.
    3. You can check this in the Software Advisor Tool for which you may require CCO Login.
    Software advisor tool
    http://www.cisco.com/cgi-bin/Support/CompNav/Index.pl?Introduction=True
    4. Not sure.

Maybe you are looking for

  • Can't open a document linked in a PDF. "This document tries to establish a connection". What can I do?

    When I try to open open a document which is linked in a PDF(I opened the PDF with Adobe Reader) there comes a safety warning: This document tries to establish a connection: file://(fileserver) Is this Website confidential, click on "allow". Is the we

  • Is the Nvidia 9400m sufficient for my tasks?

    Hi, I am currently looking at getting a 15" MBP. Right now, I can't decide whether to spend the extra $300 for a disrete video card. I will be doing light photoshop work (nothing close to 100-200 mb files), probably some work with Dreamweaver and Pre

  • SAP ABAP or JAVA

    Hello Folks, Just Wanted to know according to you, what is better SAP ABAP or Java Developer as a Career. Presently I have 1 year Exp. as ABAP Consultant and 6 months as Java Developer I should continue in which career ? Please help me with this.

  • The clone stamp will not work in AE CC

    When I click on the clone stamp tool, nothing changes and I'm unable to use the tool. The clone stamp symbol becomes highlighted, but the curser doesn't change to a circle over the image and just stays as an arrow. When I try to sample an area by hol

  • Invoice for Auto Recharge that has not been comple...

    I have an invoice dated Jan 13 for an AU$400 recharge for my Business Manager account. Payment should have been against my AMEX card but this has not happened. So I now have an invice for a recharge I need that has not completed. What do I do? Can I