Cisco Quality Manager 8.5 "Domain could not be validated" error

Hi
Has anyone encountered this error when they attempt to add domain to Quality Manager?
I need to understand how I can fix this problem?
Marsha

My issue is stil not received, i hav send a document to the system team to follow for the integration. The AD configuration for QM shud be very expicit or else integration will not work. I am attachin the doc here. Let me knw if that helps.

Similar Messages

"Credentials could not be validated" Error - Weblogic deployment of BSSV

Hi All
I am a long time integrator with little JDE experience.
I am tasked with getting Business Services published from JDE Business Functions.
I have followed the MTRs and have Weblogic 10.3 on a Windows 2008 64 bit server.
JDE is E812 with tools 8.98 4
The Management Agent is installed and on the Server Manager, the Business Services Server was created.
A business function has been written and after following the steps from both the Business Services Dev guide and a presentation from openworld, the function was built into a published Business Services.
Now, when this is tested, both from the JDeveloper Integrated Server and from the Weblogic described above, the following error occurs:
"Credentials could not be validated from message or from configuration file"
Can anyone suggest why this happens? Are there deployments missing from my J2EE?
Apart from the deployment from the Jdevelopper, a complete build of the ear has been done and deployed on the managed server, but this gives the same error.
I have checked that the jdbj.ini is installed correctly and that the details are correct in there.
Any help would be appreciated.
Thanks,
Ryan
Edited by: 912783 on 2012/02/10 5:46 AM
Edited by: 912783 on 2012/02/10 6:21 AM

Hi
We managed to get this working, but it is almost impossible to say what went wrong in the first place.
Basically, we began a fresh install with a new domain and following the docs everything came right!
there was no need to go into the JDE DB tables though.

Cisco Quality Management: 8.5.2.18. Recording only one agent.

Good day! There are a cluster of two CUCM (8.5.1.13900-5), UCCX (8.5.1.11004-25, Licence – Enchanced), Cisco Quality Management (8.5.2.18), Cisco IP Comunicator as agent's phone (using SCCP for a registration) at the deployment. When I login in the Cisco Unified Workforce Optimization, I see only one of agent's recording, although I see four agent who are configurated at Quality Administrator Managment . I noticed the only one of difference among the agents. It's the field "Name Dialing" at User Configuration of CUCM (I reckon it doesn't matter). But possibly I need to set a configuration at local computers agents. When I tried to fix the my issue and I couldn't find the Device name for JTAPI user at CUCM. I add the Device and I have a question. Do I have to add only Device or CTI as well? I attached the screenshot "JTAPI". It is the configuration of application user at CUCM. Could you help me with recomendations for fixing this issues?

Hi
My first suggestion would be to look at your AQM config. AQM uses CTI as well, and may be set up with a different user for JTAPI.
I typically set AQM and UCCX to use the same user (the one specified for RM-CM in UCCX) so that if an agent works for UCCX, he will work for AQM - for JTAPI at least.
Regards
Aaron

"Document Domain could not be saved."

Evening folks,
I'm working on a website and I'm trying to save and I'm getting an error that says "Document Domain could not be saved."
A little background.
In mid-may I wiped my drive and re-installed leopard. I reloaded iweb 09 and brought in the domain file from my back up. I was able to save at that point.
I haven't been using iWeb lately because I'm using Rapidweaver more, but I need to work on a site that I have in iWeb.
There currently is a domain file in application support. I tried moving it onto the desktop because I've read that can work, but still no dice.
Any thoughts on how I can get this to save?

Ran in a similar problem now with the 'document Domain could not be saved' message. When I closed and tried to reopen iWeb, the making working area would not open. Got it working again using the following steps:
1. Close iWeb 09
2. Find and renamed the Domain.site2 file to something else while retaining the extension
3. Launch iWeb 09 and force it to create a new Domain.site2 file
4. If iWeb opens up, create a new site and put in something that you can save. HIT SAVE. (at this stage, I did not get an error message).
5. Close iWeb 09
6. Restore the original Domain.site2 file to it's original name. Double-click it to launch iWeb. Hopefully your old iWeb file should work now. Mine did.

The user function manager DLL (ufmanager.dll) could not be found.

Hi Everyone,
I just spent two horrible days getting a Windows 2003 server to run our .net 2008 asp Crystal report. It was all because of the unknown.rpt error. The final answer was to give the NETWORK SERVICE account full control to the C:\ and then remove that permission.
Now, I'm up to my next challenge:
Error in File C:\WINDOWS\TEMP\CrystalReport {2A76C903-674A-4A7B-AA04-44FC7E206C3F}.rpt:
The user function manager DLL (ufmanager.dll) could not be found.
That dll is there on the server. What should I do?
Please help!!!!
Thanks,
Ed

Ok, here is where the fun begins as the issue you are getting is not something I've run into before. A few clarifications and suggestions re. troubleshooting.
I used the latest runtime.msi
- confirm this was CRRedist2008_x86.msi (just want to be sure)
pdf about the unknown.rpt.
- do you have a link or name of the pdf?
To troubleshoot let's do this:
1) Download the depends utility. I want to see if there is a missing dependency. depends is here:
http://www.dependencywalker.com/
open the ufmanager.dll in depends and see what it reports.
2) Run Process Monitor utility. ProcMon can be downloaded from here:
http://technet.microsoft.com/en-ca/sysinternals/bb896645.aspx
Make sure you filter ProcMon for your process as this will shrink the log file. Then look for ufmanager.dll and see where the app is trying to load it from.
3) Check this registry entry:
HKLM\software\business objects\10.5\crystal reports
See that CommonFiles is pointing to c:\program files\business objects\common\2.8\bin.
4) Copy the ufmanager.dll from c:\program files\business objects\common\2.8\bin to your app directory (this is just a test as I want to see if we can load the dll from anywhere...)
Ludek

Envelope sender domain could not be resolved

For this error:
Apr 23 18:11:07 2008 Info: ICID 815272710 Address: <nurmaria> sender rejected, envelope sender domain could not be resolved
If the domain has multiple MX(es) record. I.e cardig.com has :
cardig.com mail is handled by 10 mail.cardig.com.
cardig.com mail is handled by 10 mail2.cardig.com.
Does Ironport check all the mx(es) first then reject if one of them is not exists?
Or just query it once (first match mx or first low priority mx)?
TIA.

I think that the problem is not related to MX records existence or priority.
The error you found occurs when a DNS server does not provide an answer to the query your appliance send when checking the sender.
Suppose that a remote SMTP server connect to your appliance and send a "MAIL FROM: user @ domain.com" SMTP command; at this point your appliance checks whether "domain.com" exists or not and therefore asks for a MX record for "domain.com" to the DNS you configured. The DNS in turn searches for an authoritative DNS for "domain.com" and then sends it a query for the MX records of "domain.com"; if it doesn't get an answer your appliance cannot validate the sender domain and rejects the connection with the error you reported.
In your example this means that the appliance didn't even know that the MX for cardig.com were "mail.cardig.com" and "mail1.cardig.com", but rather that the DNS server didn't get that information from the authoritative DNS server of "cardig.com".
Hope this helps.
Andrea

One or more accounts provided could not be validated

I am trying to install the second node in the same management group of scom 2012. but I keep running into the error
one or more accounts provided could not be validated.
the account is the system center data access service account
any ideas ? The account is not locked out.

Check that this account has sufficient rights on the maangement server. local admin could be nice. Also try to startup a program such as notepas or whatever using the Run as DIfferent User option and type the credentials. Dont forget to place the domain
name as well as domain\sdkaccount (and do not copy/paste into those fields! Manually type everything in that wizard.
Bob Cornelissen - BICTT (My Blog about SCOM) - MVP 2012 + 2013 and Microsoft Community Contributor 2011 + 2012 Recipient

To recipient Unknown could not be delivered [Error:80040919]

To All
I have unity 7.0 (2) running and the problem is that no voice mail is been received id mailbox.
In the event loggin I see the following:
Event Type:    Error
Event Source:    CiscoUnity_UMR
Event Category:    UMR Thread Error
Event ID:    113
Date:        6/14/2013
Time:        3:42:01 PM
User:        N/A
Computer:    VIPNLAP501
Description:
A message with the subject:
<Unknown>
to recipient <Unknown> could not be delivered [Error:80040919]. It was moved to the failed directory. This can occur for several reasons: the recipient mailbox may be disabled or inaccessible, Cisco Unity may be having trouble connecting with the partner server, or the Cisco Unity messaging component may not be properly configured. If this condition persists, contact Cisco TAC. 0x00000C94
And what I see is also that the is no sync on ldap, this last I have seen this bevore and solf the the problem but now I can not see where it is going wrong.
It is no unity connect.
Please help,
Thanks
Regards,
Jan Meeling

Hello Jan,
The PW (Permission Wizard) is found on the Tools Depot> Administration Tools> Permision Wizard. If you right click on it and select properties you will be able to see the version. If you do not have the latest vesion (v. 3.0.0.7) you should start by installing it.
Go to:
http://ciscounitytools.com/SiteList/AllDownloads/alldownloads.html
Under Title search for:
Permissions Wizard 5.0(1)+
Running the Permission Wizard is required with a Domain Admin account, usually the Unity Install account has this included, to verify, go to Start> Run> dsa.msc> Click on Find> Type Unity Install> Click on Member of tab.
Additionaly this utility does not involve any downtime to your environment. At the beginning of the Wizard confirm that the proper accounts are assigned to the services, i.e: Directory Services-> UnityDirSvc, for Message Store-> UnityMsgStore. When yo reach the point to select the Mail Stores make sure that all the proper or desired mailstores are included.
At the end if it fails for 1 item, and it is permissions to delete objects this can be expected.
To fully understand this tool and see screen shots of running the tool go to:
http://ciscounitytools.com/Applications/Unity/PermissionsWizard/Unity50/Help/PWHelp_ENU.htm
The MSCW (Message Store Configuration Wizard) is a tool used to partner and synchronize with your Exchange server and is found in Start>Control Panel> Programs> Add Remove Programs> Doble click on Message Store Configuration Wizard. Running this tool is service impacting, meaning it requires to stop Unity services.
At the end of the Wizard you are prompted for a last account, which is the Directory Service account, make sure you are using the proper one, i can't stress this enough.
It would also be good to ensure that your Unity System is able to communicate accordingly to your Domain Controllers and Global Catalog. You can check this by going to Tools Depot> Administration> DCGC Reconnect> Click on the DC tab hit Force Reconnect do the same in the GC tab (this is again NOT service impacting). After you do that go to Event viewer (eventvwr.msc)
One event will be seen with the Domain Controller:
The Cisco Unity service that monitors Active Directory (AvDSAD) completed a full
synchronization cycle with
Another will be seen with the Global Catalog:
...event global catalog (AvDSGlobalCatalog) completed a full synchronization cycle with ...
If you do not see a complete synchronization there might be issues in your network or to the DC GC's Unity is talking to and therefore not able to retrieve the proper information of the users.
If you run DBWalker does it give you any further insight?
It would be usefull if you could clarify whether this issue is
-for all users: mayor changes on either Unity or Exchange
-a set of users:random or specific to a mailstore
-single user: are there any differences in Exchange between the working users and the non-working one; is it disabled on AD?
Best regards,
David Noel Rojas Peck
Email: [email protected]
Mon, Wed, and Fri 12:00 pm to 9:00 pm ET, Tue and Thu 8:00 am to 5:00pm ET
Cisco Worldwide Contact link is below for further reference.
http://www.cisco.com/en/US/support/tsd_cisco_worldwide_contacts.html

Server 2008 Pinter install error OPERATION COULD NOT BE COMPLETED (error 0x900f0214)

I downloaded the HP Universal printer driver for a LaserJet 4250dn network printer to our server running SERVER 2008 SP2.
I dowloaded the zipped executable files for both the PCL5 and PCL6 drivers to the desktop and ran the EXE to unzip the files. When I tried to run the INSTALL.EXE file (as an ADMINISTRATOR) for BOTH drivers, the following occurs:
Answer YES to EULA
Select TRADITIONAL MODE (or DYNAMIC MODE - it doesn't matter - neither one works)
Click INSTALL
Immediately I get the error OPERATION COULD NOT BE COMPLETED (error 0x900f0214)
Click OK
Click FINISH
This happens with both the PCL5 & PCL6 driver installations.
I activated FILE SHARING, PRINTER SHARING, and NETWORK DISCOVERY but did not solve the problem.
I was logged in as the Domain Administrator and the Local Admin also.
Any suggestions?

Hi selmore,
This is a commercial line product. For the best answer to your questions you will need to repost your question to the following links.
http://h30499.www3.hp.com/t5/Business-Support-Forums/ct-p/business-support
http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"

Even after resets get "The backup disk image "/Volumes/FreeAgent GoFlex Drive/MacBeth (2) 1.sparsebundle" could not be created (error 22)."

HELP! "The backup disk image “/Volumes/FreeAgent GoFlex Drive/MacBeth (2) 1.sparsebundle” could not be created (error 22)."
TC estimates over 750GB for full backup.
Late 2010 MBA is connected wirelessly to
802.11n (1st gen) TC that is connected via ethernet hub built into house to motorola router using charter.com for internet.
I have had same problem for over 150 days and multiple reboots, restarts in proper order, firmware updates, unplugs with 5min plus gaps, bypassing the tc and using external 500gb WD mybook via usb to time capsule, replacement of the WD mybook to new 2TB Free Agent GoFlex drive, etc, etc, etc! Note: I originally named my MBA hard drive MacBeth, but at some point months ago, it said backup already existed and system automatically created MacBeth (2), worked for a while, then stopped again, despite trying nearly daily.
I gave up and started using Carbon Copy Clone daily for just the 128gb on internal SSD of my late 2011 11" MacBook Air, but need to get past these time capsule errors to back up the external disk! Due to lack of space in MBA, I had long ago transferred both itunes and iphoto and all imovie/fcpx files to a 1tb external disk (WD Passport) that I keep in my bag with MBA. It is partitioned with 150gb for cloning the MBA, and over 750gb for media/itunes/iphoto/etc.
Also, I have endured months of "your hard drive is full" messages and system lockups, applying the solution given to me by genious bar (deleting all aol.com outboxes/recovered messages/spam/trash under library/mail/V2/Mailboxes folders, empty trash, restart....watch recovered hard drive space mysteriously shrink next couple days to zero.....repeat)
Due to lack of space, I had not been able to do javascript and other system updates. Yesterday, I noticed even safari bookmark bar had mysteriously emptied (not disappeared, I can hide and show the space where the bar used to be - it is just blank area with no data except for eyelass-book-topsites icons), so I transferred a few large quicktime movie files recorded with isight camera to the external disk, and freed up 20 gbs for the first time!
This got my hopes up yesterday because after I completed all system/software updates, suddenly the bookmark bar showed up and I was able to start the time capsule backup! It took overnight preparing for backup, but finally started and progressed to 12gb of the 100gb+ needed (i guess the update where it left off months ago for the estimated 750gb for the full backup?), then I put system to sleep and took it with me (thus leaving the wireless time capsule network as I do daily fully expecting it to continue when I returned home in the evening.) But alas, upon return, back to the "Time Machine could not complete backup, The backup disk image ".....sparsebundle" could not be created (error 22)" Ugh! More reboots, unplugs, 5min gaps....still Ugh!
So the problem continues...please help! Here are my settings:
About this mac:
Mac OS X V. 10.7.5
processor 1.6 ghz intel core 2 duo, memory 4 4g 1067 MHz DDR3
software up to date!
Airport Utility:
V 6.2 (620.33)
both internet globe and TC show green dots in graphic, however internet occasionally shows yellow then goes to green, but still gets error 22. Suddenly TC showed explanation mark and says lost connection and asked if I wanted to 'forget', gave same errors, then mysteriously went back to green, but still got error 22!.
Internet:
connection: connected, displays router address, 2 dns server, and domain name: charter.com
Time Capsule:
shows network, ip address, serial number, version 7.6.3, status: (green dot) Setup over WAN,
wireless clients: phones, macbooks (including this MBA), printers, wii
If you need other settings to help me, just ask! I have read a few of the other solutions in forums, but trying not to erase disks, especially since it worked for a minute yesterday!

To step sideways.. why not just use CCC to backup the 750GB of the hard disk to the TC.
You need to understand this is going to be a super slow process and each time you stop it.. it is going to give issues. CCC will at least do a more reliable job of it than TM.
I would also say.. this is going to be tough without ethernet. You need to understand the backup speed over wireless can be 10GB per hour.. that makes 75hrs to backup the disk. The air needs to run non-stop doing that.. without you touching it.
I would get another external drive.. plug that into the MBA and if you really want to use TM.. make a backup one to the other.. but CCC will again do a better job and work faster. It will be much faster than over wireless.
I am trying to think of ways around the issue of just speed.. but plainly you have lots of other issues.. being the simple unreliablity of the TM to identify the TC.
If you want to make this work.. give yourself a weekend.
Load 5.6 utility into the MBA..
http://support.apple.com/kb/DL1482
Take the TC back to 7.5.2 firmware. It is a really old version and latest firmware does it no good at all.
Wipe its hard disk using erase and start over.. give it new names for everything.
So call it TC
Set the wireless to 5ghz and name it TC5ghz
Use WPA2 Personal security. Use a 10 character passkey non dictionary.
At 5ghz you should get 2x the speed as at 2.4ghz but the air will need to be right next to the TC..
(alternatively buy the USB to ethernet cord apple have available.. it is $30 in the apple store and do it over pseudoethernet. http://store.apple.com/au/product/MC704ZM/A/apple-usb-ethernet-adapter That is the wrong store but you get the idea. )
WIth a fully clean system.. now do a full reset of TM.
See A4 http://pondini.org/TM/Troubleshooting.html
Direct the TM to back to the TC.. and make sure the external hard disk is not excluded.
Of course the TC has to be 1TB version to fit that much data.. goes without saying right.
Even over pseudo - ethernet this will take many hours.. and you basically have to leave it to work.. do not touch it.. make sure the MBA cannot sleep though.. turn off sleep.. beforehand.

The backup disk image "/Volumes/FW1000HD/MacBkPro.sparsebundle" could not be created (error 1).

I added an 1TB external usb hard disk to my time capsule as the existing 1TB hard disk is nearly full (less than 12 GB left on time capslule hard disk). Initially, I connected external hard disk to my MacBookPro (late 2009 Intel machine) and erased most of the data on that disk. I added the disk to time machine's backup disks thru the time machine window in system preferences. Now I supposedly have both hard disks, the one in the time capsule and the new usb hard disk, available for backup. Time Machine immediately backed up my system, which consists of my MacBookPro hard disk (about 96.8 GB) and another external usb hard disk which contains about 500 GB of data, on the new extenal hard disk.Time Machine did not attempt to create a new sparsebundle at that time on my new external backup disk. This backup was done while the new backup hard disk and the data disk were both connected to the MacBookPro and the Time Capsule was directly connected by ethernet cable to the MacBookPro. I then disconnected the two hard disks from the MacBookPro and reconnected them both via usb to the Time Capsule. Now, hopefully, the external usb backup hard disk can be written to via wi-fi thru the usb connection thru the Time Capsule? I successfully use the data disk (which contains my full iTunes Library) from the Time Capsule all of the time.
Time Machine has continued to backup small backups of a few MB to a few hundred MB to the Time Capsule hard disk. Time Machine has attempted at least twice that I know of to set up a sparsebundle on the new external backup hard disk, but it has failed both times with the following message:
The backup disk image “/Volumes/FW1000HD/MacBkPro.sparsebundle” could not be created (error 1).
Before the two attempts that I witnessed to create the sparsebundle on the new backup drive, I got the following message:
The identity of the backup disk “FW1000HD” has changed since the previous backup.
I did not change the identity of the FW1000HD, but it originally was connected directly to the MacBookPro when it was backed up. Could this be the problem? And if so, how do I fix this, so I can use this hard disk for back up from the wi-fi connection to Time Capsule?
Gary Olson

I'm not sure this is at the root of your problems, but Time Machine manages backups to a local disk differently than to a network disk. The Time Machine backup written to the disk while it was connected locally can't be used for network backups.

CS6 & CC Instantly Close, Audition "License could not be validated"

Hi,
I am given the full CS6 suite through my school. I also just subscribed to the student Creative Cloud subscription (which I really don't want - I wanna wait until it is available through my school - but I thought just having CC would get rid of my CS6 woes).
What's happening:
The night before last I was editing a huge, important project in Premiere Pro CS6 and Audition. Following some tutorials and wanting to make use of Audition CC's new features, I installed a trial of Audition CC and everything worked fine.
Yesterday morning Premiere Pro closed every time it opened a project. Didn't matter WHICH project or if I created a new project. --Wasn't just crashing - if I moved a source file and relocated it when I opened the project, it would ask me if I wanted to save the project before closing.-- Every other CS6 program would do the same thing except Audition CS6 which said "Your license could not be validated. Audition must now shut down." I'm assuming this is what's happening to the other programs.
Hours of pulling my hair out, researching and trying fixes, I subscribe to CC and let it download the programs overnight.
This morning, it's doing the exact same thing. Photoshop, Premiere close instantly, Audition says my license could not be validated.
What the heck is going on??
Here is a YouTube video showing what happens when I open Audition, Premiere & Photoshop. (The weird error that pops up when I load the support chat is just my Gyazo GIF being unable to upload the gif - irrelevant.) https://www.youtube.com/watch?v=b12euH1aFME
Log-stuff:
The only major concerning thing I found in the Event Viewer this morning was:
Activation context generation failed for "C:\Program Files (x86)\Adobe\Adobe Dreamweaver CC\Dreamweaver.exe".Error in manifest or policy file "" on line . A component version required by the application conflicts with another component version already active. Conflicting components are:. Component 1: C:\Windows\WinSxS\manifests\amd64_microsoft.windows.common-controls_6595b64144ccf1df_6.0. 7601.17514_none_fa396087175ac9ac.manifest. Component 2: C:\Windows\WinSxS\manifests\x86_microsoft.windows.common-controls_6595b64144ccf1df_6.0.76 01.17514_none_41e6975e2bd6f2b2.manifest.
Sounds like an activation issue - maybe related to my problem.
[I've seen people ask for and post the Adobe logs but no post saying where those are. Point me and I will post them.]
My PC:
Windows 7 Ultimate 64-bit, activated
24GB RAM
AMD Phenom II X4 965BE 3.4GHz Quad Core CPU
240GB SSD that the programs boot from
2TB HDD that the caches are (were ) on
Nvidia GeForce GTX 660 GPUNvidia GeForce 9800 GT GPU (PhysX - Adobe set to use the 660, which is CUDA compatible, etc.)
1080p + 1280x1024 resolution
What I've Tried (That I Can Remember):
Reinstalling (multiple times)
Creative Cloud Cleaner (+ reinstalling)
Signing out & back in of the creative cloud program
Using a new user account & repeating
Buying & installing full CC collection
Uninstall - Creative Cloud Cleaner - Reboot - CCleaner clean/registry fix - reboot - reinstall
Contacted Support chat - just told me it's a technical issue, but the tech team isn't in til Monday.......
More things
HELP!!!!!!!

-Unfortunately, no. I spoke a couple times with Adobe tech support via live chat (though 99% of the time I spent on there was validating that I owned their product and then telling me they had to pass me around to repeat ..) and then @AdobeCare helped me test a few things and it still did not work, so I went with a full Windows reinstall (and migrated from 7 to 8) to save me the headache.
I was avoiding the suggested OS reinstall due to saving time/headache, but the opposite happened.
It works fine other than 1 error in Win8 for me now.
-Yes I tried in selective startup and safe mode.
-According to everything I found, it wasn't actually related to licensing at all.
-Hardware setup did not change. Just installed Adobe Audition CC trial.
-Yes, both CS6 and CC managed to do the same thing.
-HOWEVER everything is working in my new Windows install, except Photoshop CS6 is now not updating, giving me this:
Photoshop 13.1.2 for Creative Cloud
Installation failed. Error Code: U44M1P7"
Any ideas?
Thanks,

The filter expression is on external data and could not be validated.

The filter expression is on external data and could not be validated. It may not be supported in Web browser forms.
I am reciveing this error in my infopath 2010 browser form when I am trying to filter a drop down list from sharepoint.
I thought filters were available on infopath 2010 browser forms or are they only available from values inside the form?
I did have a look around the forums but only could find this error occuring during beta stage.
Thanks

Ok, so you shouldn't be filtering in the form, because that means it downloads the entire list first and then filters out the items. That's client-side filtering. What you want to do is server-side filtering by doing a parameterized query.
Set the data connection NOT to automatically download
Add Form Load rules that do the following:
First, "Set a Field's Value" and set the position query node of the data connection to the value of "manager" (whatever the exact syntax is)
Then query the data connection
Doind this should make it ONLY download items where position=manager instead of downloading all items and filtering. This is a much better practice and was not even available in 2007, so you should make full use of it in 2010. Even so, what you
were doing should have worked anyway, so I'm not sure what's going on there.
When you do the filtered dropdown, your Source field should be the repeating group of the data connection, not the property itself. The property should only be selected in Value and DisplayName. The group should be in the Source field, and THAT'S
where you apply the filter.
SharePoint Architect || Microsoft MVP ||
My Blog
Planet Technologies ||
SharePoint Task Force

Web Service in EnterpriseOne: Credentials could not be validated

I am trying to run one of the lab exercises to test the address book web service. While testing this web service; I am getting the following error in the SOAP response XML when nothing is passed in the WS-Security :
<faultstring>Internal Server Error (Caught exception while handling request: java.lang.RuntimeException: Credentials could not be validated from message or from configuration file.)</faultstring>
Whenever I pass in my user/id password; I get the following message in the response XML:
<faultcode>env:MustUnderstand</faultcode>
<faultstring>SOAP must understand error: {http://docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-secext-1.0.xsd}Security</faultstring>
I am new to web services and am unsure of what setup is missing in or outside of EnterpriseOne. I will really appreciate if someone could shed some light on this.

It's worth checking that security has been enabled for the web service. I seem to remember that I had to do this when I got the same error a while back.
In OAS, log onto the Enterprise Manager on your OAS server and select the OC4J instance that contains the Business Services Server. Click on the Web Services tab and then select the Web Service that you're trying to test (eg: RI_AddressBookManagerHttpPort). Click on the Administration tab and if the Security feature is not enabled then press the Enable/Disable Features button, move Security across to the Enabled Features pane and press OK.
Back on the Administration tab, select the Edit Configuration icon for the Security Feature, and press the Inbound Policies button. Ensure that the Use Username/Password Authentication checkbox is selected. The Password Type should be Plain Text.
You shouldn't need to bounce the OC4J instance.
I'm not sure about Websphere without doing more research, but I imagine there must be a similar option.
Good luck,
Dave

J2EE Server could not be started - Error -11113

HI,
     J2EE Server could not be started - Error -11113.
       My system configuration:
      Solution Manager 7.0
      Windows server 2003 32-bit
      ABAP Stack is working fine.
     1.After SGEN in client 001 all the users like J2EE_ADMIN,J2EE_Guest,Slddsuser,SAPJSF etc were deleted.
     2.I have manually create all the users and assigned the respective roles.
     3.Even now i face a same problem as JAVA Server (Server0) dies while starting framework.
Please find the specific problem in the log of DEV_SERVER0
[Thr 7968] JLaunchRequestQueueInit: create named pipe for ipc
[Thr 7968] JLaunchRequestQueueInit: create pipe listener thread
[Thr 8104] JLaunchRequestFunc: Thread 8104 started as listener thread for np messages.
[Thr 6456] WaitSyncSemThread: Thread 6456 started as semaphore monitor thread.
[Thr 7968] NiInit3: NI already initialized; param 'maxHandles' ignored (1;202)
[Thr 7968] CPIC (version=700.2009.02.11)
[Thr 7968] [Node: server0] java home is set by profile parameter
     Java Home: C:\j2sdk1.4.2_13
[Thr 7968] JStartupICheckFrameworkPackage: can't find framework package F:\usr\sap\SM2\DVEBMGS70\exe\jvmx.jar
[Thr 5636] Wed May 18 08:45:59 2011
[Thr 5636] JHVM_RegisterNatives: registering methods in com.sap.bc.krn.perf.PerfTimes
[Thr 5636] Wed May 18 08:46:00 2011
[Thr 5636] JHVM_RegisterNatives: registering methods in com.sap.bc.proj.jstartup.JStartupFramework
[Thr 5636] JLaunchISetClusterId: set cluster id 701470150
[Thr 5636] JLaunchISetState: change state from [Initial (0)] to [Waiting for start (1)]
[Thr 5636] JLaunchISetState: change state from [Waiting for start (1)] to [Starting (2)]
[Thr 6748] Wed May 18 08:46:30 2011
[Thr 6748] JLaunchIExitJava: exit hook is called (rc = -11113)
[Thr 6748] **********************************************************************
ERROR => The Java VM terminated with a non-zero exit code.
Please see SAP Note 943602 , section 'J2EE Engine exit codes'
for additional information and trouble shooting.
[Thr 6748] JLaunchCloseProgram: good bye (exitcode = -11113)
This below log files belong to server0.log
     at com.sap.engine.services.security.SecurityServerFrame.start(SecurityServerFrame.java:194)
     at com.sap.engine.core.service630.container.ServiceRunner.startApplicationServiceFrame(ServiceRunner.java:214)
     at com.sap.engine.core.service630.container.ServiceRunner.run(ServiceRunner.java:144)
     at com.sap.engine.frame.core.thread.Task.run(Task.java:64)
     at com.sap.engine.core.thread.impl5.SingleThread.execute(SingleThread.java:83)
     at com.sap.engine.core.thread.impl5.SingleThread.run(SingleThread.java:156)
Caused by: com.sap.engine.services.security.exceptions.BaseSecurityException: No active userstore is set.
     at com.sap.engine.services.security.server.UserStoreFactoryImpl.getActiveUserStore(UserStoreFactoryImpl.java:80)
     at com.sap.engine.services.security.server.jaas.LoginModuleHelperImpl.update(LoginModuleHelperImpl.java:415)
     at com.sap.engine.services.security.server.jaas.LoginModuleHelperImpl.<init>(LoginModuleHelperImpl.java:84)
     at com.sap.engine.services.security.server.SecurityContextImpl.<init>(SecurityContextImpl.java:58)
     at com.sap.engine.services.security.SecurityServerFrame.start(SecurityServerFrame.java:147)
     ... 5 more
#1.5 #000BCDCBCF4F001F0000000C00001AA80004A38454DADAA1#1305688661484#/System/Server##com.sap.engine.core.service630.container.ServiceRunner#######SAPEngine_System_Thread[impl:5]_31##0#0#Error#1#/System/Server#Plain###Core service security failed. J2EE Engine cannot be started.#
#1.5 #000BCDCBCF4F001F0000000E00001AA80004A38454DADE18#1305688661484#/System/Server/Critical##com.sap.engine.core.Framework#######SAPEngine_System_Thread[impl:5]_31##0#0#Fatal#1#com.sap.engine.core.Framework#Plain###Critical shutdown was invoked. Reason is: Core service security failed. J2EE Engine cannot be started.#
Kindly help me in this issue and do let me know if any informations are needed.
Regards
Gopinath M.L

Hi,
Which UME user you are talking about i checked in config tool where there is no user in UME.
Kindly advice how to create a UME User if not available to start the server.
Note: Http://servername;57000/ is says that dispatcher working but not connect to JAVA Server.
Regards
Gopinath M.L

Cisco Quality Manager 8.5 "Domain could not be validated" error

Similar Messages

Maybe you are looking for