Cisco Router 1841,2911

Does Cisco router 1841 or 2911 or any other model routers has default IP or not

If I understand your question correctly; no, there are no IPs configured by default.

Similar Messages

  • Cisco Router 1841 is it support CME ?

    I have cisco router 1841 is it support CME? I tried to put this command    myrouter(config)# telephony-services       but is not recognized ?

    1841 supports VWIC card perfectly. it works great in WAN data.
    Here is VWIC card in my 1841 in "show diag",
            WIC/HWIC Slot 1:
            VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1
            Hardware Revision        : 0.0
            Top Assy. Part Number    : 800-22629-05
            Board Revision           : C0
            Deviation Number         : 0
            Fab Version              : 04
            PCB Serial Number        : FOCxxxxxxx
            RMA Test History         : 00
            RMA Number               : 0-0-0-0
            RMA History              : 00
            Product (FRU) Number     : VWIC2-2MFT-T1/E1
            Version Identifier       : V01
            EEPROM format version 4
            EEPROM contents (hex):
              0x00: 04 FF 40 03 FC 41 00 00 C0 46 03 20 00 58 65 05
              0x10: 42 43 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 31
              0x20: 33 30 34 33 57 42 53 03 00 81 00 00 00 00 04 00
              0x30: CB 90 56 57 49 43 32 2D 32 4D 46 54 2D 54 31 2F
              0x40: 45 31 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF
              0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
              0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
              0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

  • Configure ATM on cisco router 1841 for PPPoE

    Hi Geeks,
    I have searched the net with answers but still no success to achieving what I needed.
    My scenario, I 'am replacing  my Netcom with a cisco 1841 router. Now, I need advise or better guided steps on how to configure my ATM interface for PPPoE to connect to my ISP network. With the netcom its easy since its uses GUI  and connection picks up automatically as long username and password are correct to connect to ISP.
    Appreciate any help here?
    Thank you.

    from the sounds of it you purchased a '4 port WAN Interface Card' to be put into your router.
    (the HWIC4 cannot be used to create a 'DMZ' as you require; you will need additional Ethernet interfaces, not WAN interfaces)
    a few things first...
    1) yes you have increased the routers ability to serve more than one network. with an HWIC4, you can configure upto 4 more WAN segments that the router can route for.
    2) if you had a 4 port Ethernet Card, then you could configure each interface to act like a DMZ, but without proper security in place, it will not be much more than a 'hop' from one network to another.
    NOTE: you need to build very detailed, granular access lists to filter traffic if you wish to have any chance of provding the slightest amount of security to your inside users & hosts.
    (a firewall will provide you better security control and DMZ definition and is a recommended best practice for the solution you're looking for)
    your DMZ definition says it all, "...subnet between a trusted network and an untrusted network..."
    firewalls inherently provide a 'trusted' interface, an 'untrusted' interface and one or more 'less than trusted' or DMZ interfaces.
    routers do not inherently provide this type of security segregation. you should be using a firewall to provide your solution and security in this case.

  • Vlan routing with cisco router and linksys switch

    I have a linksys switch width vlan configured, connected to a Cisco router (1841), but I cant route between vlan’s.
    Please help me!!
    It Works with a Cisco switch perfectly(with the same ip and vlan).

    Yes. the linksys switch (SRW2024 24-Port 10/100/1000 Gigabit Switch) supports trunking.
    If you want you can visit the link and see that the switch supports vlan, dot1q and trunking.
    http://www.linksys.com/servlet/Satellite?childpagename=US%2FLayout&packedargs=c%3DL_Product_C2%26cid%3D1123638180432&pagename=Linksys%2FCommon%2FVisitorWrapper

  • Problem with gateway voice in router 1841 or 1760

    Reading Cisco documentation , I see that router 1841 and 1841 does not support as Voice Gateway.
    My idea is to connect to him a Primary ISDN (30 channel B) so that it works like a PBX and users can make calls towards PSTN.
    Is possible to do this with these routers (1841, 1760)?
    Thanks.

    Using T1, E1 or G.703 multiflex trunk interface cards with cisco 1760 or 1800 series are both available.
    You can use these cards with 1760:
    VWIC-1MFT-T1
    One-port FJ-48 multiflex trunk - T1
    VWIC-2MFT-T1
    Two-port RJ-48 multiflex trunk - T1
    VWIC-2MFT-T1-DI
    Two-port RJ-48 multiflex trunk - T1 with drop and insert
    VWIC-1MFT-E1
    One-port RJ-48 multiflex trunk - E1
    VWIC-2MFT-E1
    Two-port RJ-48 multiflex trunk - E1
    VWIC_2MFT-E1-DI
    Two-port RJ-48 multiflex trunk - E1 with drop and insert
    VWIC-1MFT-G.703
    One-port RJ-48 multiflex trunk - E1 G.703
    VWIC-2MFT-G.703
    Two-port RJ-48 multiflex trunk - E1 G.703
    You can use these cards with 1800 series:
    VWIC-1MFT-T1
    1-port RJ-48 multiflex trunk voice/WAN interface card—T1
    VWIC-2MFT-T1
    2-port RJ-48 multiflex trunk voice/WAN interface card—T1
    VWIC-2MFT-T1-DI
    2-port RJ-48 multiflex trunk voice/WAN interface card—T1 with drop and insert
    VWIC-1MFT-E1
    1-port RJ-48 multiflex trunk voice/WAN interface card—E1
    VWIC-2MFT-E1
    2-port RJ-48 multiflex trunk voice/WAN interface card—E1
    VWIC-2MFT-E1-DI
    2-port RJ-48 multiflex trunk voice/WAN interface card—E1 with drop and insert
    VWIC-1MFT-G703
    1-port RJ-48 multiflex trunk voice/WAN interface card—G.703
    VWIC-2MFT-G703
    2-port RJ-48 multiflex trunk voice/WAN interface card—G.703
    you can get detailed information about compatibility with 1760 by using the below link:
    http://www.cisco.com/en/US/products/hw/routers/ps221/products_data_sheet09186a00800920f2.html
    you can get detailed information about compatibility with 1800 series by using the below link:
    http://www.cisco.com/en/US/products/ps5853/prod_module_install_config_guide09186a00802c47ef.html

  • I need find IOS appropriate router 1841

    I need upgrade IOS on router 1841 , but new IOS 12.4T size Over memory (our Memory 32M), someone help me find IOS 
    appropriate for upgrade
    * I download version c1841-adventerprisek9-mz.124-25g.bin , but i not sure it use with our router
    i have show version
    Cisco IOS Software, 1841 Software (C1841-ADVENTERPRISEK9-M), Version 12.4(9)T7,
    RELEASE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2008 by Cisco Systems, Inc.
    Compiled Thu 10-Jan-08 15:41 by prod_rel_team
    ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
    Thaitech-pattanee uptime is 4 days, 1 hour, 11 minutes
    System returned to ROM by reload at 10:57:40 WAST Thu Oct 9 2014
    System restarted at 10:59:00 WAST Thu Oct 9 2014
    System image file is "flash:c1841-adventerprisek9-mz.124-9.T7.bin"
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected]
    Cisco 1841 (revision 7.0) with 354304K/38912K bytes of memory.
    Processor board ID FHK123821SF
    2 FastEthernet interfaces
    1 ATM interface
    1 Virtual Private Network (VPN) Module
    DRAM configuration is 64 bits wide with parity disabled.
    191K bytes of NVRAM.
    31360K bytes of ATA CompactFlash (Read/Write)
    Configuration register is 0x2102
    Thank
    Best regards
    Sompon

    hi
    i need features adventerprisek  same old IOS and i can't buy either memory , i need upgrade for solve internet ,
    you  have IOS recommend  me ?
    regards
    Sompon

  • Cisco Router tried to take a firmware update and no longer works

    Ok so internet was working fine until Cisco Connect told me to take an update.  My connection is wired and there were no disruptions during the download.  Yet the download still failed and now my power light blinks continuously and there is no internet access.  I tried instructions on "How to unbrick your Cisco Router", even got them to work, it took the firmware update from the cmd line.  Still doesnt work though.  What's wrong with this thing and how do i fix it?
    Solved!
    Go to Solution.

    I ended up downloading a firmware utility program and was able to get it to reload. The power light became solid somewhere between 2-5 mins, however still didnt connect to the internet.  Found that all this factory resetting will change your Internet access name & password, with no way to find out the new one.  You have to remove the Cisco Connect program from your computer and reload it from the original disk.  Only then will you be up and running again.  While I appreciate the response Helm, I was way beyond a 30 second reset button solution when I posted this lol.

  • Cant ping behind cisco router (site2site vpn)

    Dears;
    After configure site to site vpn between cisco router and fortigate firewall,
    site A : 10.0.0.0/24     behind fortigate
    site B: 10.10.10.0/24  behind cisco router
    the tunnel is up and I can ping 10.0.0.1 from site B and can ping 10.10.10.1 from site A but I cant ping any ip inside 10.0.0.0/24 form site B or network 10.10.10.0/24 from site A
    my cisco router configuration is
    Current configuration : 2947 bytes
    ! No configuration change since last restart
    version 15.1
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    boot-start-marker
    boot-end-marker
    enable secret 4 EE103as6FtdocdBefpgugX6P9eGaDKDyBvwz7AywH5Q
    no aaa new-model
    memory-size iomem 10
    clock timezone cairo 2 0
    crypto pki token default removal timeout 0
    ip source-route
    ip dhcp excluded-address 192.168.16.1
    ip dhcp excluded-address 10.10.10.1 10.10.10.10
    ip dhcp pool GUEST
     network 192.168.16.0 255.255.255.0
     default-router 192.168.16.1
     dns-server 8.8.8.8 8.8.4.4
    ip dhcp pool LAN
     network 10.10.10.0 255.255.255.0
     default-router 10.10.10.1
     dns-server 8.8.8.8 8.8.4.4
    ip cef
    controller VDSL 0
    ip ssh version 2
    crypto isakmp policy 10
     encr aes
     hash sha256
     authentication pre-share
     group 5
    crypto isakmp key 6 *********** address 4.x.x.x no-xauth
    crypto ipsec transform-set myset esp-aes esp-sha256-hmac
    crypto map kon-map 10 ipsec-isakmp
     set peer 4.x.x.x
     set transform-set myset
     set pfs group5
     match address 105
    interface Ethernet0
     no ip address
     no fair-queue
    interface ATM0
     no ip address
     ip mtu 1452
     ip tcp adjust-mss 1452
     no atm ilmi-keepalive
    interface ATM0.1 point-to-point
     ip flow ingress
     pvc 0/35
      encapsulation aal5snap
      pppoe-client dial-pool-number 1
    interface FastEthernet0
     switchport mode trunk
     no ip address
    interface FastEthernet1
     no ip address
    interface FastEthernet2
     switchport access vlan 2
     no ip address
    interface FastEthernet3
     no ip address
    interface Vlan1
     ip address 10.10.10.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface Vlan2
     ip address 192.168.16.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
    interface Dialer1
     ip address negotiated
     ip mtu 1492
     ip nat outside
     ip virtual-reassembly in
     encapsulation ppp
     ip tcp adjust-mss 1452
     dialer pool 1
     ppp authentication chap pap callin
     ppp chap hostname
     ppp chap password 0
     ppp pap sent-username
     crypto map kon-map
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    ip nat inside source list 100 interface Dialer1 overload
    ip route 0.0.0.0 0.0.0.0 Dialer1
    access-list 100 deny   ip 10.10.10.0 0.0.0.255 10.0.0.0 0.0.0.255
    access-list 100 permit ip 10.10.10.0 0.0.0.255 any
    access-list 100 permit ip 192.168.16.0 0.0.0.255 any
    access-list 105 permit ip 10.10.10.0 0.0.0.255 10.0.0.0 0.0.0.255
    banner motd ^C^C
    end
    when ping from cisco router
    konsuler#ping 10.0.0.27 source vlan1
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 10.0.0.27, timeout is 2 seconds:
    Packet sent with a source address of 10.10.10.1
    Success rate is 0 percent (0/5)
    help please

    Thank you karsten
    I can ping interface of router from remote site but cant ping any device behind the router and can ping firewall interface but cant ping any device behind the firewall
    -counters in
    # sh crypto ipsec sa
    increased only while ping 10.0.0.1 or 10.10.10.1 from both sides
    r#show crypto session detail
    Crypto session current status
    Code: C - IKE Configuration mode, D - Dead Peer Detection     
    K - Keepalives, N - NAT-traversal, T - cTCP encapsulation     
    X - IKE Extended Authentication, F - IKE Fragmentation
    Interface: Dialer1
    Uptime: 00:03:12
    Session status: UP-ACTIVE     
    Peer: 4.x.x.x port 500 fvrf: (none) ivrf: (none)
          Phase1_id: 4.x.x.x
          Desc: (none)
      IKEv1 SA: local 6.x.x.x/500 remote 4.x.x.x/500 Active
              Capabilities:(none) connid:2001 lifetime:22:39:59
      IPSEC FLOW: permit ip 10.10.10.0/255.255.255.0 10.0.0.0/255.255.255.0
            Active SAs: 2, origin: crypto map
            Inbound:  #pkts dec'ed 9 drop 0 life (KB/Sec) 4605776/3407
            Outbound: #pkts enc'ed 14 drop 0 life (KB/Sec) 4605775/3407

  • Not able to telnet or ssh to outside interface of ASA and Cisco Router

    Dear All
    Please help me with following question, I have set up testing lab, but still not work.
    it is Hub and spoke site to site vpn case, connection between hub and spoke is metro-E, so we are using private ip for outside interface at each site.
    Hub -- Juniper SRX
    Spoke One - Cisco ASA with version 9.1(5)
    spoke two - Cisco router with version 12.3
    site to site vpn has been successful established. Customer would like to telnet/ssh to spoke's outside ip from Hub(using Hub's outside interface as source for telnet/ssh), or vise versa. Reason for setting up like this is they wants to be able to make configuration change even when site to site vpn is down. Sound like a easy job to do, I tried for a long time, search this forum and google too, but still not work.
    Now I can successfully telnet/ssh to Hub SRX's outside interface from spoke (ASA has no telnet/ssh client, tested using Cisco router).
    Anyone has ever done it before, please help to share your exp. Does Cisco ASA or router even support it?
    When I tested it, of cause site to site vpn still up and running.
    Thanks
    YK

    Hello YK,
    On this case on the ASA, you should have the following:
    CConfiguring Management Access Over a VPN Tunnel
    If your VPN tunnel terminates on one interface, but you want to manage the ASA by accessing a different interface, you can identify that interface as a management-access interface. For example, if you enter the ASA from the outside interface, this feature lets you connect to the inside interface using ASDM, SSH, Telnet, or SNMP; or you can ping the inside interface when entering from the outside interface. Management access is available via the following VPN tunnel types: IPsec clients, IPsec LAN-to-LAN, and the AnyConnect SSL VPN client.
    To specify an interface as a mangement-only interface, enter the following command:
    hostname(config)# management access management_interface
    where management_interface specifies the name of the management interface you want to access when entering the security appliance from another interface.
    You can define only one management-access interface
    Also make sure you have the pertinent configuration for SSH, telnet, ASDM and SNMP(if required), for a quick test you can enable on your lab Test:
      SSH
    - ssh 0 0 outside
    - aaa authentication ssh console LOCAL
    - Make sure you have a default RSA key, or create a new one either ways, with this command:
        *crypto key generate rsa modulus 2048
    Telnet
    - telnet 0 0 outside
    - aaa authentication telnet console LOCAL
    Afterwards, if this works you can define the subnets that should be permitted.
    On the router:
    !--- Step 1: Configure the hostname if you have not previously done so.
    hostname Router
    !--- aaa new-model causes the local username and password on the router
    !--- to be used in the absence of other AAA statements.
    aaa new-model
    username cisco password 0 cisco
    !--- Step 2: Configure the router's DNS domain.
    ip domain-name yourdomain.com
    !--- Step 3: Generate an SSH key to be used with SSH.
    crypto key generate rsa
    ip ssh time-out 60
    ip ssh authentication-retries 3
    !--- Step 4: By default the vtys' transport is Telnet. In this case, 
    !--- Telnet and SSH is supported with transport input all
    line vty 0 4
    transport input All
    *!--- Instead of aaa new-model, the login local command may be used.
    no aaa new-model
    line vty 0 4
      login local
    Let me know how it works out!
    Please don't forget to Rate and mark as correct the helpful Post!
    David Castro,
    Regards,

  • Remote access VPN with Cisco Router - Can not get the Internal Lan .

    Dear Sir ,
    I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .Please see the attachment for Scenario, Configuration and Ping status.
    I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
    Below is the IP address of the device.
    Local PC connect with Router -2 (Through MS Loopback) Router -2 Router-1 PC -01
    IP Address :10.10.10.2 Mask : 255.255.255.0 F0/01
    IP address:10.10.10.1
    Mask:255.255.255.0 F0/0
    IP Address :20.20.20.1
    Mask :255.255.255.0
    F0/1
    IP address :192.168.1.3
    Mask:255.255.255.0
    F0/0
    IP address :20.20.20.2
    Mask :255.255.255.0
    F0/1
    IP address :192.168.1.1
    Mask:255.255.255.0
    I can ping from local PC to the network 10.10.10.0 and 20.20.20.0 .Please find the attach file for ping status .So connectivity is ok from my local PC to Remote Router 1 and 2.
    Through Cisco remote vpn client, I can get connected with the VPN Router R1 (Please see the VPN Client pic.)But cannot ping the network 192.168.1.0
    Need your help to fix the problem.
    Router R2 Configuration :!
    version 12.4
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname R2
    boot-start-marker
    boot-end-marker
    no aaa new-model
    memory-size iomem 5
    no ip icmp rate-limit unreachable
    ip cef
    no ip domain lookup
    ip auth-proxy max-nodata-conns 3
    ip admission max-nodata-conns 3
    ip tcp synwait-time 5
    interface FastEthernet0/0
    ip address 20.20.20.2 255.255.255.0
    duplex auto
    speed auto
    interface FastEthernet0/1
    ip address 10.10.10.1 255.255.255.0
    duplex auto
    speed auto
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    control-plane
    line con 0
    exec-timeout 0 0
    privilege level 15
    logging synchronous
    line aux 0
    exec-timeout 0 0
    privilege level 15
    logging synchronous
    line vty 0 4
    login
    end
    Router R1 Configuration :
    version 12.4
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname R1
    boot-start-marker
    boot-end-marker
    aaa new-model
    aaa authentication login USERAUTH local
    aaa authorization network NETAUTHORIZE local
    aaa session-id common
    memory-size iomem 5
    no ip icmp rate-limit unreachable
    ip cef
    no ip domain lookup
    ip auth-proxy max-nodata-conns 3
    ip admission max-nodata-conns 3
    username vpnuser password 0 strongpassword
    ip tcp synwait-time 5
    crypto keyring vpnclientskey
    pre-shared-key address 0.0.0.0 0.0.0.0 key cisco123
    crypto isakmp policy 10
    encr 3des
    hash md5
    authentication pre-share
    group 2
    crypto isakmp client configuration group remotevpn
    key cisco123
    dns 192.168.1.2
    wins 192.168.1.2
    domain mycompany.com
    pool vpnpool
    acl VPN-ACL
    crypto isakmp profile remoteclients
    description remote access vpn clients
    keyring vpnclientskey
    match identity group remotevpn
    client authentication list USERAUTH
    isakmp authorization list NETAUTHORIZE
    client configuration address respond
    crypto ipsec transform-set TRSET esp-3des esp-md5-hmac
    crypto dynamic-map DYNMAP 10
    set transform-set TRSET
    set isakmp-profile remoteclients
    crypto map VPNMAP 10 ipsec-isakmp dynamic DYNMAP
    interface FastEthernet0/0
    ip address 20.20.20.1 255.255.255.0
    ip nat outside
    ip virtual-reassembly
    duplex auto
    speed auto
    crypto map VPNMAP
    interface FastEthernet0/1
    ip address 192.168.1.1 255.255.255.0
    ip nat inside
    ip virtual-reassembly
    duplex auto
    speed auto
    ip local pool vpnpool 192.168.50.1 192.168.50.10
    ip forward-protocol nd
    ip route 10.10.10.0 255.255.255.0 FastEthernet0/0
    no ip http server
    no ip http secure-server
    ip nat inside source list NAT-ACL interface FastEthernet0/0 overload
    ip access-list extended NAT-ACL
    deny ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
    permit ip 192.168.1.0 0.0.0.255 any
    ip access-list extended VPN-ACL
    permit ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
    control-plane
    line con 0
    exec-timeout 0 0
    privilege level 15
    logging synchronous
    line aux 0
    exec-timeout 0 0
    privilege level 15
    logging synchronous
    line vty 0 4
    end

    Dear All,
    I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .
    Please see the attachment for Scenario, Configuration and Ping status. I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
    Waiting for your responce .
    --Milon

  • Site-to-Site VPN between Cisco ASA 5505 (8.4) and Cisco Router (IOS 15.2)

    Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
    I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
    Please help me to find where is the issue.
    I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
    192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
    Here is my current configuration.
    Thanks for your help.
    IOS Configuration
    version 15.2
    crypto isakmp policy 1
    encr aes 256
    authentication pre-share
    group 2
    crypto isakmp key cisco address 198.0.183.225
    crypto isakmp invalid-spi-recovery
    crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
    mode transport
    crypto map static-map 1 ipsec-isakmp
    set peer S2.S2.S2.S2
    set transform-set AES-SET
    set pfs group2
    match address 100
    interface GigabitEthernet0/0
    ip address S1.S1.S1.S1 255.255.255.240
    ip nat outside
    ip virtual-reassembly in
    duplex auto
    speed auto
    crypto map static-map
    interface GigabitEthernet0/1
    ip address 192.168.17.1 255.255.255.0
    ip nat inside
    ip virtual-reassembly in
    duplex auto
    speed auto
    access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
    ASA Configuration
    ASA Version 8.4(3)
    interface Ethernet0/0
    switchport access vlan 2
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.83.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address S2.S2.S2.S2 255.255.255.248
    ftp mode passive
    same-security-traffic permit intra-interface
    object network inside-network
    subnet 192.168.83.0 255.255.255.0
    object network datacenter
    host S1.S1.S1.S1
    object network datacenter-network
    subnet 192.168.17.0 255.255.255.0
    object network NETWORK_OBJ_192.168.83.0_24
    subnet 192.168.83.0 255.255.255.0
    access-list outside_access_in extended permit icmp any any echo-reply
    access-list outside_access_in extended deny ip any any log
    access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    nat (inside,outside) source dynamic inside-network interface
    nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
    nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
    nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
    crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set vpn-transform-set mode transport
    crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set L2L_SET mode transport
    crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
    crypto map vpn 1 match address outside_cryptomap
    crypto map vpn 1 set pfs
    crypto map vpn 1 set peer S1.S1.S1.S1
    crypto map vpn 1 set ikev1 transform-set L2L_SET
    crypto map vpn 20 ipsec-isakmp dynamic dyno
    crypto map vpn interface outside
    crypto isakmp nat-traversal 3600
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto ikev1 policy 20
    authentication pre-share
    encryption aes-256
    hash sha
    group 2
    lifetime 86400
    group-policy GroupPolicy_S1.S1.S1.S1 internal
    group-policy GroupPolicy_S1.S1.S1.S1 attributes
    vpn-tunnel-protocol ikev1
    group-policy remote_vpn_policy internal
    group-policy remote_vpn_policy attributes
    vpn-tunnel-protocol ikev1 l2tp-ipsec
    username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
    username admin password rqiFSVJFung3fvFZ encrypted privilege 15
    tunnel-group DefaultRAGroup general-attributes
    address-pool vpn_pool
    default-group-policy remote_vpn_policy
    tunnel-group DefaultRAGroup ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group DefaultRAGroup ppp-attributes
    authentication ms-chap-v2
    tunnel-group S1.S1.S1.S1 type ipsec-l2l
    tunnel-group S1.S1.S1.S1 general-attributes
    default-group-policy GroupPolicy_S1.S1.S1.S1
    tunnel-group S1.S1.S1.S1 ipsec-attributes
    ikev1 pre-shared-key *****
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:f55f10c19a0848edd2466d08744556eb
    : end

    Thanks for helping me again. I really appreciate.
    I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
    Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
    Because on Cisco ASA I guess I have everything.
    Here is show crypto session detail
    router(config)#do show crypto session detail
    Crypto session current status
    Code: C - IKE Configuration mode, D - Dead Peer Detection
    K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
    X - IKE Extended Authentication, F - IKE Fragmentation
    Interface: GigabitEthernet0/0
    Session status: DOWN
    Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
          Desc: (none)
          Phase1_id: (none)
      IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
            Active SAs: 0, origin: crypto map
            Inbound:  #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
            Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
    Should I see something in crypto isakmp sa?
    pp-border#sh crypto isakmp sa
    IPv4 Crypto ISAKMP SA
    dst             src             state          conn-id status
    IPv6 Crypto ISAKMP SA
    Thanks again for your help.

  • TS2709 I have AppleTV and Ipad2 running VJay app to my TV over a private cisco router disabled firewall but I keep loosing the video on my TV after a few minutes what can I do?

    I have AppleTV and Ipad2 running VJay app to my TV over a private cisco router disabled firewall but I keep loosing the video on my TV after a few minutes what can I do?

    I also get this problem on my iPad, so probably not related to the AppleTV. On the iPad I restarted Airport Extreme this time, and then the iPad saw my Home Sharing.
    So to recap, restarting the router or Airport Express allowed the iPad and AppleTV to see Home Sharing. Restarting AppleTV also allows AppleTV to see Home Sharing.
    So does anyone have any idea?
    Thanks

  • Do you need a cisco router at remote sites when using VRF BGP?

    Hello.....
    If you could refer to the attached document and read the following... I need to know if a CISCO router is required for each of the sites.   OR does the ISP (Provider) provide the only required Router in the private cloud?
    We want to replace the Cisco 891 with a PepLink but I don't know if we can do that.  Can anyone jump in and help me understand?
    When we hear about VRF, its almost synonymous to MPLS VPN. Virtual Routing and Forwarding is commonly used by Service Providers to provide services within an MPLS cloud with multiple customers. The most interesting feature of this is that, VRF allows creation of multiple routing tables within a single router. This means that overlapping use of IP addresses from different customers is possible. Some enterprises use VRF to seggrate their services like VOIP, wireless, geographical location and other varieties.

    Whether you can replace the 891 device with another device boils down to a single question: Do you need to run BGP with the Service Provider in order to use their service. If you need to run a routing protocol with your service provider, your service is likely a L3VPN (IP VPN) solution ( i.e. you inject your site's routes into the providers L3VPN session, they use MP-BGP+VRF for segmentation within their network).
    If, however, they just drop you a L2 connection and provide L2 emulated services ( e.g. L2VPN or VPLS ) across their network, then your device can be whatever you want it to be.
    From your device's perspective, it is not VRF aware. That is, it does not know about how the service provider segments your service from another customers. In the L3VPN case, your device is routing-protocol aware. In the L2VPN case, your device is not routing protocol aware and does not need to form adjacency with the service provider's equipment.
    HTH.
    Rate if helpful.

  • How to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

    how to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

    Hi ,
     Have you got any additional public IP Address from your service provider , If yes on router you can have static route for those additional IP Address pointing to your ASA  outside interface . 
    Accordingly you can configure NAT 
    HTH
    Sandy . 

  • How do I identify the ports to open on my cisco router from Rogers to allow access through my apple tv - I am not using wireless!

    I only have spotty access at best through m Apple TV to itunes, netflix and utube.  I am  Rogers subscriber (feel my pain) and am now using their CISCO DCP3825 router.  Apple TV purchased this past Christmas.  I am not using wireless. No issues prior to replacing my old router and Rogers modem to go to DCP3825.
    Apple TV is up to date - updated by connecting to my Macbook Pro.
    Rogers tech support was of no help - suggested I open some ports - where do I go for the list(s)?
    Any help would be much approeciated.

    did this search for you
    https://www.google.dk/search?client=opera&q=control+open+ports+on+cisco+router&s ourceid=opera&ie=utf-8&oe=utf-8&channel=suggest#client=opera&hs=N7P&channel=sugg est&sclient=psy-ab&q=+open+ports+on+cisco+router&oq=+open+ports+on+cisco+router& gs_l=serp.3..0i7l3.16726.16726.0.16996.1.1.0.0.0.0.49.49.1.1.0...0.0...1c.1.9.ps y-ab.olPaFzjSlmE&pbx=1&bav=on.2,or.r_cp.r_qf.&bvm=bv.45175338,d.bGE&fp=43d9a4347 e8aaeda&biw=1535&bih=773
    this may be of intrest
    http://www.tek-tips.com/viewthread.cfm?qid=1163449

Maybe you are looking for