Cisco router and security SDM download

I know it is end of life. But can any of you tell whether we can download it? any version would be fine. I searched cisco website without any results.
thanks,
Han

2800ISR
http://www.cisco.com/en/US/products/ps5854/index.html
3560G-24PS (there isn't a 10/100 switch with the required forwarding rate and PoE support).
http://www.cisco.com/en/US/products/hw/switches/ps5528/prod_models_comparison.html
HTH,
Edison.

Similar Messages

How to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

how to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

Hi ,
Have you got any additional public IP Address from your service provider , If yes on router you can have static route for those additional IP Address pointing to your ASA outside interface .
Accordingly you can configure NAT
HTH
Sandy .

On Mac OS X Lion rebooted Cisco router and my network has disappeared

I have no internet connection now. My netwrok disappeared from the list. I did the on and off , reboot modem etc. I tried to reinstall the Cisco software and a message popped up saying Cisco doesn't support my version of OS X. The wifi was working fine on Lion for at least a week, then wifi started dropping off on my iPad so that is why I rebooted the router and now it doesn't work at all.

What Cisco software are you running on your Mac? You should be able to connect to the router's control panel by going to its network address with a browser, although be aware that Safari douesn't handle some of the control panel javascript correctly, so you might want to use Firefox.

I have a Cisco router and purchased a 1st generation airport, would like to find outbid I could connect the AirPort Extreme wireless with a USB wireless, so I can connect to be able to put the airport in another room to beagle to have it close to stereo

Help setting up airport express. Wireless for streaming

Cisco Linksey EA4500 dual band,
Airport express model and serial # 0024369ca089. 6f9075pa2u6
Ipurchasedan airport it appears to be a 1st generation
What I am trying to accomplish is to have the airport close to my sound system so I can play the I tunes through my built in house stereo system,presently the modem and Cisco router are on a different floor

Vlan routing with cisco router and linksys switch

I have a linksys switch width vlan configured, connected to a Cisco router (1841), but I cant route between vlans.
Please help me!!
It Works with a Cisco switch perfectly(with the same ip and vlan).

Yes. the linksys switch (SRW2024 24-Port 10/100/1000 Gigabit Switch) supports trunking.
If you want you can visit the link and see that the switch supports vlan, dot1q and trunking.
http://www.linksys.com/servlet/Satellite?childpagename=US%2FLayout&packedargs=c%3DL_Product_C2%26cid%3D1123638180432&pagename=Linksys%2FCommon%2FVisitorWrapper

Help with connecting MacBook Pro with Cisco Routing and Switches?

I'm running a CiscoASA 5510 router with several Cisco WS-C2960-48TT-L switches on a local network to connect with MacBook Pro. I need to be able to restrict access to specific users via their computer MAC address. ie: Joe Blow is limited to connecting through Switch 1 on port 10 and anywhere else he tries to plug in will simply not work.

You need to look at the documentation that came with your router and switches. Or ask your network admin to set it up. Your question has nothing to do with your Macbook Pro configuration. MAC filtering is done in the router not in the computers/devices connecting to the router.

CS Mars, Cisco Works and Security Manager

If we wanted to get all three applications, do cisco bundle it into one package? Or does it have to be purchased separately?

do we need a NetFlow card or is the service implemented by default in Cat4500. Is MARS & CSM suitable solution for main configuring, incident monitoring and evaluation of ASA5520 & Cat4500?
Yes, you need WS-F4531= card (Netflow is not available in Cat IOS as a service/command), which works with Cat 4500 Sup IV/V.
MARS is a monitoring device, and CSM is a management device. You can get critical NBA (Network Behaviour Analysis) alerts from MARS, and from CSM you can get configuration backups/audit/bulk administration (of security devices only).
Hope that helps.

Cisco 7920 and Aironet 1100 (Downloading config file)

For some reason the 7920 is trying to Downlaod the config file and can't pass that screen.
It authenticates just fine and the i get the screen "downloading config file" and that's it.
It's been doing the same thig all morning.
Not sure what's going on.
please help.
Call Manager 4.1.3 Aironet 1100
Thanks
Zeek

ok, so i guess after a while, the phone said "upgrading firmware" and after resseting, i got to the screen with the line up.
I still have a problem though.
i can dial a phone, it will call but once someone answer on the other side, the 7920 resets itself.
PLease help.

Connecting to NME-IPS results in connecting to cisco router itself

Suddenly, without any clear reason, I cannot access the NME-IPS in my router.
Instead it connects to the router console.
The IP address is also pingable.
Output:
gateway#service-module IDS-Sensor 1/0 status
Service Module is Cisco IDS-Sensor1/0
Service Module supports session via TTY line 66
Service Module is in Steady state
Service Module heartbeat-reset is enabled
Getting status from the Service Module, please wait..
Cisco Systems Intrusion Prevention System Network Module
Software version: 7.0(6)E4
Model:             NME-IPS
Memory:            443504 KB
Mgmt IP addr:      192.168.11.99
Mgmt web ports:    443
Mgmt TLS enabled: true
gateway#service-module IDS-Sensor 1/0 session
Trying 192.168.11.99, 2066 ... Open
C
Cisco Router and Security Device Manager (SDM) is installed on this device.
This feature requires the one-time use of the username "cisco"
with the password "cisco". The default username and password have a privilege level of 15.
Please change these publicly known initial credentials using SDM or the IOS CLI.
Here are the Cisco IOS commands.
username <myuser> privilege 15 secret 0 <mypassword>
no username cisco
Replace <myuser> and <mypassword> with the username and password you want to use.
For more information about SDM please follow the instructions in the QUICK START
GUIDE for your router or go to http://www.cisco.com/go/sdm
User Access Verification
Username:

If IME is not connecting, is it giving you some sort of error?
Do you have ASDM launcher loaded? if so, does it also fail to connect?
When you launch IME are you prompted for a password, is that failing on the password entry or does it simply fail to connect to the device?
I have not been able to access my NME via https either, I get a Java error, but I pretty much always use Cisco IME to access my NME module so I have not chased down the Java issue.

Changing Wireless Channel on CISCO Router

How do I change the wireless channel on a CISCO 1811W (MPC8500) router? Currently it is channel 10 and I prefer to change it to channel 1 to reduce interference with microwave oven. I have already replaced the standard antenna with 7dBi high gain antenna.
Out of 12 wireless clients about 3 are being dropped whenever microwave oven is turned on. These clients have Linksys WMP54G Wireless G PCI adapters. Other client computers are notebooks with builtin wireless adapters and desktops with Belkin, TRENDnet, or Motorola Wireless PCI or USB adapters.
All computers are within about 60'-80' radius from the CISCO wireless router and are about 20' away from the microwave oven. Any suggestions?
Thanks.
N Murugesan
[email protected]

I tried in SDM and could not find a way to change radio channel.
How do I invoke command line interface (CLI)? I found the following from Cisco Wireless ISR and HWIC Access Point Configuration Guide.
Configuring Radio Channel Settings
Step 1          configure terminal                     - enter global configuration mode
Step 2          interface dot11radio 0                   - enter interface configuration mode for the radio interface. The 2.4 GHz radio is radio 0, and 5 GHz is 1.
Step 3           channel frequency | least-congested - set the default channel for the wireless radio - Channel 1 2412 MHz, Ch 2 2417, Ch 3 2422, etc.
                                                                      - To search for the least-congested channel on startup, enter least-congested
Step 4          end                                        - return to privileged EXEC mode
Step 5          copy running-config startup-config          -(optional) save your entries in the configuration file.
I need help to enter into the privileged EXEC mode. Once I type https://10.10.10.1 (router IP) I get a login screen (Level_15 or view access). Once I enter User Id and Password I get Cisco Router and Security Device Manager (SDM) that has Home, Configure, and Monitor tabs.
Configure - Interfaces & Connections - Edit Interfaces & Connections - DOT11Radio0 shows status as Up; but does not allow me to change anything. Neither channel nor frequency is displayed.
So I not sure how to use SDM to change the default channel.
I will appreciate any help in this regard.
N Murugesan
[email protected]

Cisco 851 and "L2TP Client-Initiated Tunnels"

Hi there,
I've got cisco 851 and have to connect it to my local provider.
Unfortunately, I found it doesn't support "L2TP Client-Initiated Tunnels" feature, I couldn't find it in feature list on cisco feature navigator page for cisco 851.
Router is getting IP on wan interface by dhcp and after that must dial out to provider's router by l2tp.
Could somebody help me to configure router for that kind of connection?
Thanks, Alexc

Cisco 850 Series integrated services routers are fixed-configuration routers that support broadband cable and Asymmetric DSL (ADSL) over analog telephone lines connections in small offices (Figures 1 and 2). They provide the performance needed to run concurrent services, including firewall and encryption for VPNs and optional 802.11b/g for wireless networking. The Cisco Router and Security Device Manager (SDM) Web-based configuration tool simplifies setup and deployment (Figure 3), and centralized management capabilities give network managers visibility and control of router configurations at the remote site.
Try:
http://www.cisco.com/warp/public/471/ms_route.html
http://www.cisco.com/warp/public/707/cmatrix.shtml

Airport Time capsule behind cisco router download speed

My airport time capsule is connected to the internet in bridge mode via a cisco router.
The cisco router provides a 99Mbps download speed. However, when I " bridge" my time capsule in between (wired) the speed slows down to 9 Mbps.
I have already tried to assign a static DHCP IP to my time capsules MAC address and disabled DMZ for that specific IP address, but am failing to get the speed up to par.
Any suggestions?

I have used Time capsule 1.5 year behind a copperjet modem on ADSL, no problems.
Changed provider and am connected by cable with new cisco modem including router.
So the set up looks like:
internet>cisco modem/router>airport time capsule>macbook pro
The cisco modem without airport time capsule is working ok: when logged in speed is 99 Mbps as it should be (wired and wireless)
Connecting cisco router with UTP cable to time capsule and time capsule with UTP to macbook slows down speed to 9 Mbps
(time capsule in bridgemode)
Specs:
Macbook pro OSX yosemite
Airport Time capsule 2TB 2013 (v 7.7.3)
Cisco modem/router:EPC3928

Problem with cisco series 800 router and SMTP

Hello,
we bought a 877 cisco router and have some problem with SMTP.
I try to read all forum and KB about but do not find any solution.
the problem is that when i try to send any email from client (windows mail) i receive a error 533: you need to supply the correct username and password.
when trying throught hmailserver i receive an email "undeliverable" with this error in body:
Error Type: SMTP
Remote server (62.149.128.202) issued an error.
hMailServer sent: EHLO Globalnet
Remote server replied: 502 unimplemented (#5.5.1)
receving email work correctly.
i'm already using smtp auth, and with my old router everything work fine.
so i beleive is a config problem, maybe with ESMTP (ehlo)?.
i attach my config:

Dear sirs
Thank you for answer so quickly
I download this document from Cisco âConfiguring the (Remote) Common Application Programming Interface for Cisco 800 Series Routerâ.
I have a Lan with Asterisk IP-PBX , the Cisco router have a BRI to public exchange (ISDN) , the router act like a DCP (ISDN- Device Control Protocol) server and listen (DCP messages) in 2578 port.
I need o know the contents of the TCP frame that carry (ISDN-TCP, the DCP messages) to put a SIP client to talk with PSTN/ISDN using the router. I want to write a software module in Asterisk that translate SIP in (ISDN-DCP) to connect the SIP Phones to the PSTN/ISDN using the BRI ports of the Cisco router. I need to now the contents of this message to dialogue with RCAPI server of the router.
If forum is the right place perhaps to put this, Could you give me a better place, a mail or other forum to receive the speciation of (ISDN-DCP)
thank you
With kinds Regards
JoÃ£o Pereira Rosa

HT5569 Yesterday, my ability to receive gmail, facebook, safari,etc.ceased on my ipad2. The wifi shows it is connected and the cisco router works ok with another computer connection. Can anyone tell me what I need to do with ipad in order to get it worki

Yesterday, my ability to receive gmail,facebook,safari,etc. ceased to perform The wifi connections shows that it is connected but I cannot get through the internet . I use a Cisco router and it is working fine with another computer and also a printer. I contacted the internet provider and they show the ipad at the router but not out through the internet. Also, yesterday my wife eliminated some programs(games,etc) from the ipad. Anway, I am thinking I am missing some setting that is not turned on as everything seems to be working fine.
Any suggestions?

Settings > General > Reset > Reset Network Settings

PXE boot via Cisco router

We have a need to netboot a PC with Linux via a Cisco router (I.E. PXEboot).
We have copied the PXE linux.cfg files to the Cisco router's flash, (Cisco 2821, IOS Advanced Security 15-1.2-T1).
We have setup the router as a TFTP server with defaulted path as tftp-server flash:tftpboot
From the pc's CMOS, we selected PXE boot.
With "debug ip packet detail", we can see the DHCP request from the PC.
We cannot however, get the router to download the Linux files to the PC.
Manually we tried:
c:\ tftp 10.0.0.1 get default - no go.
ANYONE have an idea????
Thanks
Frank

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
Hi Ash,
Thanks for the assistance.
The laptop is directly connected to the Cisco 2821 routers g0/0 interface.
The router is configured to be a DHCP server with the Cisco 2821 router IP address on g0/0 set in the DHCP configuration to be the default router. The router’s IP address is excluded from DHCP. (10.0.0.30)
If the laptop’s bios is set to PXE boot, it seems to receive an IP address from the router I.E. 10.0.0.1– verified by statically assigning another pc IP address 10.0.0.1– the 2nd pc receives an error of IP address conflict. Then set the second pc to obtain its’ IP address via DHCP, and while running debug ip packet detail on the router, I see the router running through the DHCP assignment process and finally assigns the 2nd pc 10.0.0.2.
So needless to say, I believe the DHCP setup is functioning correctly.
The problem we have at this point is nailing down the TFTP-server function running on the Cisco 2821 router.
We were able to create the directory tree on the Cisco 2821 routers flash and then copy the correct files into each directory within flash.
Using WinXP DOS prompt, tftp does not seem to function.
With debug ip packet detail running on the router and Wireshark running on the PC, we run from a DOS window c:\tftp 10.0.0.1 GET \default. No matter how we specify the path, end result is an error of some kind.
We watch debug and wireshark display the communications of the PC and router talking, but cannot seem to get the requested file.
Perhaps WinXP tftp server is flawed.
If we load TFTP32 and attempt to send and/or receive a file from flash, works fine.
The router tftp config is as:
tftp-server flash:/tftpboot/dsl/pxeboot.cfg
The actual files name is "default" and is found on the Cisco 2821 flash:/tftpboot/dsl/pxeboot.cfg directory.
No ACLs on the Cisco router and the router is pretty much right out of the box.
Firewall is disabled on both PCs.
Ping to/from the PC/router works fine.
Thanks again
Frank

Cisco router and security SDM download

Similar Messages

Maybe you are looking for