Cisco rv130w wmm powersave
Windows 8.1, 32bit, fully patched
Realtek RTL8723BS Wireless LAN 802.11n SDIO Network Adapter, driver version 3007.9.1015.2014
Cisco RV130W, firmware version 1.0.1.3
Despite of the fact that the Cisco RV130W small business router (certified by Wi-Fi Alliance to properly support WMM Power Safe) has been configured to enable WMM Power Save, a 'powercfg -energy' trace claims :
"Platform Power Management Capabilities:Wireless access point does not support WMM Power Save
The wireless access point that the computer is connected to does not support WMM Power Save Mode. The Wi-Fi modem cannot enter Power Save mode to save energy as defined in Wireless Adapter Power Policy."
________________ drahnier
Hi,
Yes, as you mentioned, the following document from Cisco indeed claims that this device supports WMM Power Save mode
http://www.cisco.com/c/en/us/products/collateral/routers/small-business-rv-series-routers/datasheet-c78-731522-00.html
While, we're not familiar with configuration for the device, it's recommended to contact the Cisco supoort to make sure that you have a correct configuration about WMM power save.
NOTE
This
response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you.
Microsoft
does not control these sites and has not tested any software or information found on these sites.
Regards
Yolanda Zhu
TechNet Community Support
Similar Messages
-
Cisco RV130W VPN firewall problems
Dear Supports:
I am newbie with Cisco, and I bought a Cisco RV130W wireless VPN router last week but
I got same problem with this router.
1)I have installed a DHCP server in our internal network so I have disabled the DHCP
service under network > LAN > LAN configuration > Server Settings(DHCP), but after
this action, all of our wireless device can not get IP again, finally I have
enabled the DHCP relay and put the DHCP server IP to "Remote DHCP Server" field, and
the problem seems fixed, may I know I have take a right action ? And if the answer
is yes, what is the usage for the DHCP Server "Disable" option ?
2)When I set DHCP to Disable, I find that dashboard still showing that the DHCP
server still in "Enabled" status (Dashboard right top corner > LAN (local network)
Interface > DHCP Server: Enabled), may I know it is a firmware bug or just some
setting I missed ?
3)WiFi signal is weak but I can not find any setting to control signal strong, some
times the SSID disappeared, finally I find that because I placed a Ext. USB 3.0 HDD
aside the router, after I remove the HDD and the SSID never disappear again, but I
don't know why this case happened and how can I prevent those case happened again?
4)In dashboard I find that VPN server > PPTP User: 0/1 , but in user manual I also
find that PPTP VPN > 10 PPTP tunnels for remote client access, may I know in
actually the router supports 1 or 10 PPTP user(s) ?
5)The PPTP VPN will disconnect automatically after connected 10~15 mins, I have try with 2 android device , one is running android 4.2 with native VPN client , and another one is running android 4.4.2 with apps "VpnRoot" , can you let me some hints how to trace and fix the problem ?
Thank for the support and I am wait for the reply , thanks.This document demonstrates how to configure a connection between a router and the Cisco VPN Client 4.x using Remote Authentication Dial-In User Service (RADIUS) for user authentication. Cisco IOS? Software Releases 12.2(8)T and later support connections from Cisco VPN Client 3.x. The VPN Clients 3.x and 4.x use Diffie Hellman (DH) group 2 policy. The isakmp policy # group 2 command enables the VPN Clients to connect.
http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a00800946b7.shtml -
SOLUTION: WMM power management not working with Realtek Wifi drivers (W8.1x64)
I'm posting this solution for anybody who might want a fix for this.
if you run powercfg.exe -energy in Windows 8.1 and view the report it makes, you will see a warning in the log that says:
"Wireless Access Point does not support WMM Powersave mode"
I do not see this warning on another laptop I have (Samsung) which uses an Intel 6230 wifi card. So I did some digging.
At first, I thought it was the router (ASUS RT-AC68P) but realized that WMM was enabled on the router. Since the Samsung notebook didn't have the problem it was obviously driver related.
Unfortunately the drivers supplied by HP and the drivers avaialble as part of "Windows Update" from MS don't address the problem. Even if you change advanced settings for the wificard from "Performance" to "Wireless" the warning persists.
I wound up doing a clean install of W8.1 Update 1 to rid my PC of bloatware, and in the process fixed the issue with "Wireless Access Point does not support WMM Powersave mode"
The default inbox drives from Microsoft work correctly and allow the router to put the wifi card to sleep when no packets are being transmitted
Recently I went to Windows update and noticed there was an updated driver - I downloded it and the problem came back.
I went to device manager, double clicked the wifi card, went to the driver tab, and selected 'rollback driver'.
Problem is resolved again.
Went back to Windows Update and it showed the realtek driver in the optional tab again - right click on it and "hide update".
Solved.
I have noticed no issues with wifi speeds, but I think the battery *is* lasting longer (only tested for a few days); not by much, but a little. Wifi speeds are top-notch, no buffering or latency issues with any web streaming or downloadingI doubt it but there's always a possibility of a bad card. I assume that you've tried multiple routers? Gone to starbucks and same thing? See if when you uninstall the drivers if windows will automatically find a driver and give that a shot. Off hand I can't think of any software related issues with the Wifi as mine has worked fine since day one.
X220~i5 2520M~8GB~Vertex2~IPS~Win7Prox64~ It's amazing. -
RV130W: 4 devices need to use the same ports.
I just started a video game streaming business and have 4 video game consoles connected and able to play online at the same time on my recently purchased Cisco RV130W.
There's only 2 games currently that we are streaming but NAT seems to be a really big issue and is causing connection problems.
I've tried leaving this in the hands of UPnP but it seems that this is an issue that cannot be resolved so simply.
All 4 consoles are Sony PS4s and to connect and play online I need them all to have access to the following ports:
TCP Outbound
TCP Inbound
UDP Outbound
UDP Inbound
80, 443, 1935, 3074-3077, 3478-3481,7500-17899, 10040-10060, 30000-40399
80, 443, 1935, 3074-3077, 3478-3481, 9293, 10040-10060
2001, 3074-3077, 3478-3481, 6000-7000, 10070, 50000-60000
2001, 3074-3077, 3478-3481, 6000-7000, 10070, 50000-60000
At best, I've got a NAT Type 2/Moderate... at worst, I can't even connect.
To answer any questions that may be coming up or rule out any suggestions I have already tried...
All devices on the LAN have a static DHCP address.
Only one console works perfectly with UPnP.
The DMZ can fix one console but makes the NAT or the other 3 unusable.
You can't forward the same ports to 4 different devices so I have to rule that out.
Port triggering doesn't work because [I am guessing] the TTL on the packets must be too long and is still hogging the ports while other consoles are trying to send data.
I made a separate VLAN20 for the consoles so I could unblock all outbound and inbound traffic with a firewall rule and that didn't fix it. ...that's why I think this is a NAT/PAT issue.
I used to be able to get 2 consoles working with my Asus RT-N56U using only UPnP.
All help is appreciated. I will provide whatever other info you need.
Thank you in advance.UPnP seems to be implemented very differently with the vendors
I would see if disabling the following on the firewall helps under Basic Settings
as they may also be part of the issue,
I know that Xbox Live likes to be able ping the wan IP, as for the PS I'd bet things are similiar
DoS Protection
Block WAN Ping Request
IPv4 Multicast Passthrough:(IGMP Proxy)
IPv4 Multicast Immediate Leave:(IGMP Proxy Immediate Leave)
UPnP Allow Users to Configure
UPnP Allow Users to Disable Internet Access
I know that Open Nat for Xbox is something you don't actually want,
as the ones who have open nat end up getting all the traffic, and they are the ones that get laggy
Unless the game they are playing has to be the server host there is no choice for the most part
Also, on most routers in regards to gaming, I've found that one should use UPnP or Port Triggering, but not both at the same time -
I have been having problems with this range extender for several days now and it is very frustrating.
I have a Sagemcom F@st 2864 router (Connection Hub) with Bell Canada. The router is broadcasting at 2.4GHz with Auto B/G/N, Channel 11, Bandwidth 20Mhz, Transmit Power 100%, WMM Enabled, WMM Powersave Enabled, WPA2-PSK (AES).
I have my RE1000 set to a static IP address (192.168.2.100), all default QoS settings, etc. It also has the latest firmware.
I have two laptops (Wireless N), a Blackberry Torch (N), iPad (N), Desktop (N), Blu-Ray player (N), iPod Touch (G) and a WES610N access point (using static IP 192.168.2.12; Xbox360, Wii, BluRay player connected to it), all connected wirelessly. I have another desktop connected directly to router via Ethernet cable.
The RE1000 will be stable for several hours (10hrs today) and then all the wireless devices will go haywire. My laptop will continuously connect and disconnect and the WES610N will do the same.
I have tried different channels, setting the router to both N-only and G-only but the issue keeps happening.
The RE1000 has 4 bars (green) strength and 3 bars (yellow) quality.
Is my product defective? Why is it that it is only stable for a limited period of time? Does the iPad or iTouch have anything to do with this issue??
Solved!
Go to Solution.As you mentioned in your post that if you connect the computer with the router's network it connects with 4 bar but gets intermittent connection. So first of all do the following steps on the router:
# Open up the browser and on the address bar type 192.168.1.1 that will open up the Router setup page.
# Lower the MTU (Maximum Transmission Unit) from 1500 to 1492 or less (usually found on your router's main/ basic setup page)
#Adjust the following advanced wireless settings:
~~ Lower the beacon interval from 100 to 75
~~ Lower the fragmentation threshold from 2346 to 2306
~~ Lower the RTS threshold from 2347 to 2304
After configuring the router then reconfigure the RE1000. So for that check the Router's DHCP client table it will show the RE1000 IP address and then configure the RE1000 again… Here is the link for the configuration of the RE1000…
http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=3760&userrole=Linksy...
Wireless settings in RE1000 will be same as router… In order to get the best performance from an RE1000 you need to place the extender in an area where you still have at least 50% signal strength to your router when you place it in the final location where the RE1000 will be used. Once after the configuration of the RE1000 try to connect the wireless laptop and check the connectivity…
Secondly in the DHCP client table the client name shows up with the Device name and not the Wireless Network Name… -
Config air-lap1041n-e-k9 with cisco 5500 (5508) series wireless controller. how to?
Hi!
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
Log from AP:
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x00000184
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialize
PCIEx: initialization done
flashfs[0]: 6 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 2369024
flashfs[0]: Bytes available: 30016000
flashfs[0]: flashfs fsck took 21 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:2b:03:dc:09:25
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 2369024
flashfs[1]: Bytes available: 29757952
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1041N-E-K9 (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FCZ1611W414
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.0.94.21
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:2B:03:DC:09:25
Part Number : 73-14034-04
PCA Assembly Number : 800-34273-05
PCA Revision Number : A0
PCB Serial Number : FOC16075VZ3
Top Assembly Part Number : 800-34284-03
Top Assembly Serial Number : FCZ1611W414
Top Revision Number : A0
Product/Model Number : AIR-LAP1041N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:09.574: *** CRASH_LOG = YES
Base Ethernet MAC address: 44:2B:03:DC:09:25
*Mar 1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1024 messages)
*Mar 1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:11.892: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
*Mar 1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
logging facility kern
^
% Invalid input detected at '^' marker.
*Mar 1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
*Mar 1 00:09:08.282: -Verify the required power-injector is installed on this
port: AIR-CT5508-K9(Gig 0/0/2).
*Mar 1 00:09:08.282: -If a power-injector is installed, issue the command:"pow
er inline negotiation injector installed"
*Mar 1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
static IP. Forcing AP to use DHCP.
*Mar 1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Not in Bound state.
*Mar 1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
. Renewing DHCP IP.
logs from wireless controller:
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
ap-manager 2 untagged 209.165.200.231 Dynamic Yes No
management 1 untagged 209.165.200.230 Static Yes No
service-port N/A N/A 192.168.1.157 Static No No
virtual N/A N/A 1.1.1.1 Static No No
(Cisco Controller) >
i conect with service-port ok and the management port works, i think.
AP442b.03dc.0925>ping 209.165.200.230
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
AP442b.03dc.0925>
Help, please!
i write in spanish:
Hola:
Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, GraciasHi!
I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
Before the logs, I see this message from AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Hola:
He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Un saludo
Antonio R.
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: AIR-CT5508-K9, VID: V02, SN: FCW1608L05X
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 17 mins 45 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Network Information
RF-Network Name............................. hosp
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Location
Site Name........................................ default-group
Site Description.................................
WLAN ID Interface Network Admission Control
1 management Disabled
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority GroupName
Press Enter to continue or to abort
AP Config
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Disabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video AC:
Video AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Press Enter to continue or to abort
802.11a Advanced Configuration
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
Radio RF Grouping
802.11a Group Mode............................. AUTO
--More or (q)uit current module or to abort
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... c4:64:13:8f:93:40
802.11a Group Member......................... c4:64:13:8f:93:40
802.11a Last Run............................... 75 seconds ago
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
--More or (q)uit current module or to abort
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
--More or (q)uit current module or to abort
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Enabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ 50
Video reserved roaming bandwidth.............. 0
802.11b Advanced Configuration
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... c4:64:13:8f:93:40
802.11b Group Member......................... c4:64:13:8f:93:40
802.11b Last Run............................... 213 seconds ago
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... hosp
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x97e2
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast
IP Status
c4:64:13:8f:93:40 209.165.200.230 hosp 0.0.0.0
Up
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 0
Probe request rate-limiting interval............. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP Hreap mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120
AP Primed Join Timeout (seconds)................. 0
Packet Forwarding watchdog timer (seconds)....... 240 (enable)
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango S
tate:Disabled
Interface Configuration
Interface Name................................... management
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 209.165.200.230
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 209.165.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 192.168.1.1
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 209.165.200.230
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... service-port
MAC Address...................................... c4:64:13:8f:93:41
IP Address....................................... 192.168.1.157
IP Netmask....................................... 255.255.255.0
DHCP Option 82................................... Disabled
DHCP Protocol.................................... Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... HOSP3C
Network Name (SSID).............................. HOSP3C
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
WLAN ACL......................................... unconfigured
DHCP Server...................................... 209.165.200.230
DHCP Address Assignment Required................. Enabled
Quality of Service............................... Platinum (voice)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled
Client MFP.................................... Optional
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Enabled
Load Balancing................................... Enabled
Mobility Anchor List
WLAN ID IP Address Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
Test Mode.................................... Off
Probe User Name.............................. cisco-probe
Interval (in seconds)........................ 300
MAC Delimiter for Authentication Messages........ hyphen
MAC Delimiter for Accounting Messages............ hyphen
Authentication Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
Accounting Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
--More or (q)uit current module or to abort
TACACS Configuration
Authentication Servers
Idx Server Address Port State Tout
Authorization Servers
Idx Server Address Port State Tout
Accounting Servers
Idx Server Address Port State Tout
LDAP Configuration
Press Enter to continue or to abort
Local EAP Configuration
User credentials database search order:
Primary ..................................... Local DB
Timer:
Active timeout .............................. 300
Configured EAP profiles:
EAP Method configuration:
EAP-FAST:
Server key ................................
TTL for the PAC ........................... 10
Anonymous provision allowed ............... Yes
Authority ID .............................. 436973636f00000000000000000000
00
Authority Information ..................... Cisco A-ID
Press Enter to continue or to abort
HREAP Group Summary
HREAP Group Summary: Count: 0
Group Name # Aps
Press Enter to continue or to abort
HREAP Group Detail
Press Enter to continue or to abort
Route Info
Number of Routes................................. 0
Destination Network Netmask Gateway
Press Enter to continue or to abort
Qos Queue Length Info
Platinum queue length............................ 100
Gold queue length................................ 75
Silver queue length.............................. 50
Bronze queue length.............................. 25
Press Enter to continue or to abort
Mac Filter Info
Press Enter to continue or to abort
Authorization List
Authorize MIC APs against AAA ................... disabled
Authorize LSC APs against Auth-List ............. disabled
Allow APs with MIC - Manufactured Installed C.... disabled
Allow APs with SSC - Self-Signed Certificate..... disabled
Allow APs with LSC - Locally Significant Cert.... disabled
Load Balancing Info
Aggressive Load Balancing........................ Disabled
Aggressive Load Balancing Window................. 5 clients
Aggressive Load Balancing Denial Count........... 3
Statistics
Total Denied Count............................... 0 clients
Total Denial Sent................................ 0 messages
Exceeded Denial Max Limit Count.................. 0 times
None 5G Candidate Count.......................... 0 times
None 2.4G Candidate Count........................ 0 times
Press Enter to continue or to abort
Dhcp Scope Info
Scope: PUNTOSAP
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 209.165.200.201
Pool End......................................... 209.165.200.229
Network.......................................... 209.165.200.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
Press Enter to continue or to abort
Exclusion List ConfigurationUnable to retrieve exclusion-list entry
Press Enter to continue or to abort
CDP Configuration
Press Enter to continue or to abort
Country Channels Configuration
Configured Country............................. ES - Spain
KEY: * = Channel is legal in this country and may be configured manually.
A = Channel is the Auto-RF default in this country.
. = Channel is not legal in this country.
C = Channel has been configured for use by Auto-RF.
x = Channel is available to be configured for use by Auto-RF.
(-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11bg :
Channels : 1 1 1 1 1
: 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): A * * * * A * * * * A * * .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11a : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
Press Enter to continue or to abort
WPS Configuration Summary
Auto-Immune
Auto-Immune.................................... Disabled
Client Exclusion Policy
Excessive 802.11-association failures.......... Enabled
Excessive 802.11-authentication failures....... Enabled
Excessive 802.1x-authentication................ Enabled
IP-theft....................................... Enabled
Excessive Web authentication failure........... Enabled
Signature Policy
Signature Processing........................... Enabled
Press Enter to continue or to abort
Custom Web Configuration
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
Web Authentication Type.......................... Internal Default
External Web Authentication URL.................. None
Configuration Per Profile:
Rogue AP Configuration
Rogue Location Discovery Protocol................ Disabled
Rogue on wire Auto-Contain....................... Disabled
Rogue using our SSID Auto-Contain................ Disabled
Valid client on rogue AP Auto-Contain............ Disabled
Rogue AP timeout................................. 1200
MAC Address Classification # APs # Clients Last Heard
Adhoc Rogue Configuration
Detect and report Ad-Hoc Networks................ Enabled
Auto-Contain Ad-Hoc Networks..................... Disabled
Client MAC Address Adhoc BSSID State # APs Last Heard
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
--More-- or (q)uit
MAC Address State # APs Last Heard
Ignore List Configuration
MAC Address
Rogue Rule Configuration
Priority Rule Name State Type Match Hit Count
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 41 mins 2 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +39 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
(Cisco Controller) >
The AP log
AP442b.03dc.0925>
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
'(index 0).
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
logging facility kern
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
0
*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
.165.200.230:5246
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established -
Cisco Flex 7500 controller with client disconnects
Hey All,
There will be alot of info in this post, hopefully all helpful, more info the better right! If you require anymore info to help me out to not hesistate to request it.
We have been having some issues with clients connecting and disconnecting several times a day and having to manually reconnect from the icon on their taskbar. We have about 380 APs, and 200+ more to deploy that we have and are licensed for but are having some issues that we want to resolve first obviously.
Some locations our setup is a bit more complex than this with multiple SSIDs and vlans, but this issue is everywhere so i will keep it to our simple setup for now:
AP Models: AIR-LAP1042N-A-K9, AIR-CAP1602I-A-K9 (Most locations do not have a mix of both, most have 1042s)
Running a single SSID - WPA/WPA2 with: WPA - TKIP and WPA2 - AES on the same SSID.
They talk back to a Cisco Flex 7500 Series through a tunnel (should not be any port blocking preventing communication)
We are running from what i understand a bad firmware version (7.6.100.0) and during our next maintenance window i am going to try and get them to change to a more stable firmware version.
Data Rates of 1,2,5.5,11 Mbps are disabled
TPCv1 coverage running
Automatic Power Assignment
I will not focus on the a/n/ac network as most of our devices are connecting to WPA due to the config they already have.
Ideally i would like to get rid of WPA all together but i am not 100% in control of the decisions to get the started and people here like to delay things lol.
It is hard to say if the issue is specific to a model as we have so few 1602Is, and it is just at our main office. I have not heard many complaints but i have noticed i will now and then get a limited or no connectivity settings on my wireless icon on my PC. I use hard-wired so i don't really notice if it is not working.
In most locations it looks like the controller is doing a decent job at selection channels to use. I did find one spot where it had on 11 APs down a long hallway, and did not use channel 6 once. I statically set that location to stagger the channels to see what kind results we had and am still waiting to hear on that as they complained the most out of all of our locations. In some cases 3 APs in a row were on channel 1 in the hallway, in alot of casses 1 was 2 times in a row as well as 11 so there was alot of overlap.
I am attaching my show sysinfo and show wlan 17 for that informtion, some of the other settings i have changed today that were previously enabled/set different are:
Disabled Cisco Aironet IE
Set channel automatic rescan from 10 mintues to 12 hours as i can image if it is changing the channels alot it can lead to disconnects.
Some of the main things we get in our message log are:
*dot1xMsgTask: Oct 16 15:17:36.943: #DOT1X-4-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:508 Max EAPOL-key M5 retransmissions exceeded for client 84:85:06:0b:a6:33
- Not sure why we get this as we have a PSK and do not have local eap enabled.....
*apfMsConnTask_6: Oct 16 15:19:01.753: #APF-3-AID_UPDATE_FAILED: apf_80211.c:6570 Error updating Association ID for REAP AP Clientc8:f9:f9:2b:fd:50 - AID 4
*apfMsConnTask_6: Oct 16 15:19:01.753: #LWAPP-3-INVALID_AID2: spam_api.c:1462 Association identifier 4 for client 18:9e:fc:4d:9e:87 is already in use by 8c:2d:aa:b7:70:5e
- There is a bug for this log, but according to the bug our 7.6.100.0 is not effected
Here is my show sysinfo:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.100.0
RTOS Version..................................... 7.6.100.0
Bootloader Version............................... 7.6.101.2
Emergency Image Version.......................... 7.6.101.2
Build Type....................................... DATA + WPS
System Name...................................... Cisco_cf:17:26
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1295
Redundancy Mode.................................. Disabled
IP Address....................................... 10.156.50.100
System Up Time................................... 52 days 5 hrs 54 mins 25 secs
System Timezone Location......................... (GMT -4:00) Altantic Time (Canada)
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... CA - Canada
--More-- or (q)uit
Operating Environment............................ Commercial (10 to 35 C)
Internal Temp Alarm Limits....................... 10 to 38 C
Internal Temperature............................. +22 C
Fan Status....................................... OK
RAID Volume Status............................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 13
Number of Active Clients......................... 1584
Burned-in MAC Address............................ 70:81:05:CF:17:20
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 600
Here is my Show wlan 17
WLAN Identifier.................................. 17
Profile Name..................................... AirCCRSB
Network Name (SSID).............................. AirCCRSB
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 1768
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 28800 seconds
User Idle Timeout................................ Disabled
Sleep Client..................................... disable
Sleep Client Timeout............................. 12 hours
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... Cisco_cf:17:26
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
mDNS Status...................................... Disabled
mDNS Profile Name................................ unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Disabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
Accounting.................................... Global Servers
Interim Update............................. Disabled
Framed IPv6 Acct AVP ...................... Prefix
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Enabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
Eap-params.................................... Disabled
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Split Tunnel (Printers).......................... Disabled
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
Local Policy
Priority Policy NameAs long as you take the configuration backup downgrading from 7.6.100.0 to 7.4.121.0 should be fine. Because this is Flexconnect deployment, make sure you review the release notes thoroughly as config like vlan mapping is impacted it is painful to reconfigure.
I still think moving to 7.6MR3 & once 8.x get stable going for that code is a good plan. Though 7.4.121.0 is assure wave it does not mean it has no bugs.(remember that prior to this 7.4.110.0 was assure wave & it deferred in quick time) . I would say 8.x going to be the code staying for long time period, so ultimately you have to be there.
In 8.x there are few FlexConnect improvements,one being AP won't reload when you change from local mode to FlexConnect.
HTH
Rasika
**** Pls rate all useful responses *** -
Small Sales Office with Cisco 857W and Wireless Skype Handset
I have a remote sales office which is connected to the internet via a Cisco 857W. One of the sales guys uses a Skype Wireless Handset. I am looking to improve the quality of the handset as much as I can with the local wireless network in the 857W. The handset has WMM (802.11e) and uses ports 1 (alternative ports 80 and 443). My question is how do I enable WMM (802.11e) on this router and how do I or should I give priority to these ports to improve call quality? Config file attached.
thanks in advance,
stuart.I'm not an expert on this subject but this link could help.
http://www.cisco.com/en/US/products/ps5853/products_configuration_guide_chapter09186a008067cc16.html -
Cisco ISE 1.2 & Cisco WLC 5508 v7.6
Hi all,
we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
Thanks all
Mario De RosaHi Neno,
right I have this almost working now.
I have simplified the setup. I am not going to do any client provisioning at the moment.
So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
Now I am trying to introduce the posture element & per user ACLs.
I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
DNS resolution seems to be working fine.
VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
VLAN10 is the branch DATA VLAN.
below is some output to give you some more details...
(Cisco Controller) >show client detail 00:24:d6:97:b3:be
Client MAC Address............................... 00:24:d6:97:b3:be
Client Username ................................. [email protected]
AP MAC Address................................... 18:33:9d:f0:21:80
AP Name.......................................... test-flex-ap
AP radio slot Id................................. 0
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 2
Hotspot (802.11u)................................ Not Supported
BSSID............................................ 18:33:9d:f0:21:81
Connected For ................................... 128 secs
Channel.......................................... 6
IP Address....................................... 10.130.130.120
Gateway Address.................................. 10.130.130.1
Netmask.......................................... 255.255.255.0
IPv6 Address..................................... fe80::f524:1910:69f0:9482
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Client CCX version............................... 4
Client E2E version............................... 1
--More-- or (q)uit
Re-Authentication Timeout........................ 1651
QoS Level........................................ Silver
Avg data Rate.................................... 0
Burst data Rate.................................. 0
Avg Real time data Rate.......................... 0
Burst Real Time data Rate........................ 0
802.1P Priority Tag.............................. disabled
CTS Security Group Tag........................... Not Applicable
KTS CAC Capability............................... No
WMM Support...................................... Enabled
APSD ACs....................................... BK BE VI VO
Power Save....................................... OFF
Current Rate..................................... m13
Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
............................................. 12.0,18.0,24.0,36.0,48.0,
............................................. 54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ No
Policy Manager State............................. POSTURE_REQD
Policy Manager Rule Created...................... Yes
AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
AAA Override ACL Applied Status.................. Yes
--More-- or (q)uit
AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
AAA Override Flex ACL Applied Status............. Yes
AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
Audit Session ID................................. c8dc800a00000005b3e7e953
AAA Role Type.................................... none
Local Policy Applied............................. none
IPv4 ACL Name.................................... none
FlexConnect ACL Applied Status................... Yes
IPv4 ACL Applied Status.......................... Unavailable
IPv6 ACL Name.................................... none
IPv6 ACL Applied Status.......................... Unavailable
Layer2 ACL Name.................................. none
Layer2 ACL Applied Status........................ Unavailable
mDNS Status...................................... Disabled
mDNS Profile Name................................ none
No. of mDNS Services Advertised.................. 0
Policy Type...................................... WPA2
Authentication Key Management.................... 802.1x
Encryption Cipher................................ CCMP (AES)
Protected Management Frame ...................... No
Management Frame Protection...................... No
EAP Type......................................... EAP-TLS
FlexConnect Data Switching....................... Local
--More-- or (q)uit
FlexConnect Dhcp Status.......................... Local
FlexConnect Vlan Based Central Switching......... No
FlexConnect Authentication....................... Central
Quarantine VLAN.................................. 0
Access VLAN...................................... 220
Client Capabilities:
CF Pollable................................ Not implemented
CF Poll Request............................ Not implemented
Short Preamble............................. Implemented
PBCC....................................... Not implemented
Channel Agility............................ Not implemented
Listen Interval............................ 10
Fast BSS Transition........................ Not implemented
Client Wifi Direct Capabilities:
WFD capable................................ No
Manged WFD capable......................... No
Cross Connection Capable................... No
Support Concurrent Operation............... No
Fast BSS Transition Details:
Client Statistics:
Number of Bytes Received................... 33698
Number of Bytes Sent....................... 19397
Total Number of Bytes Sent................. 19397
--More-- or (q)uit
Total Number of Bytes Recv................. 33698
Number of Bytes Sent (last 90s)............ 19397
Number of Bytes Recv (last 90s)............ 33698
Number of Packets Received................. 283
Number of Packets Sent..................... 147
Number of Interim-Update Sent.............. 0
Number of EAP Id Request Msg Timeouts...... 0
Number of EAP Id Request Msg Failures...... 0
Number of EAP Request Msg Timeouts......... 0
Number of EAP Request Msg Failures......... 0
Number of EAP Key Msg Timeouts............. 0
Number of EAP Key Msg Failures............. 0
Number of Data Retries..................... 53
Number of RTS Retries...................... 0
Number of Duplicate Received Packets....... 2
Number of Decrypt Failed Packets........... 0
Number of Mic Failured Packets............. 0
Number of Mic Missing Packets.............. 0
Number of RA Packets Dropped............... 0
Number of Policy Errors.................... 0
Radio Signal Strength Indicator............ -42 dBm
Signal to Noise Ratio...................... 41 dB
Client Rate Limiting Statistics:
--More-- or (q)uit
Number of Data Packets Recieved............ 0
Number of Data Rx Packets Dropped.......... 0
Number of Data Bytes Recieved.............. 0
Number of Data Rx Bytes Dropped............ 0
Number of Realtime Packets Recieved........ 0
Number of Realtime Rx Packets Dropped...... 0
Number of Realtime Bytes Recieved.......... 0
Number of Realtime Rx Bytes Dropped........ 0
Number of Data Packets Sent................ 0
Number of Data Tx Packets Dropped.......... 0
Number of Data Bytes Sent.................. 0
Number of Data Tx Bytes Dropped............ 0
Number of Realtime Packets Sent............ 0
Number of Realtime Tx Packets Dropped...... 0
Number of Realtime Bytes Sent.............. 0
Number of Realtime Tx Bytes Dropped........ 0
Nearby AP Statistics:
test-flex-ap(slot 0)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -37 dBm
test-flex-ap(slot 1)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -54 dBm
--More-- or (q)uit
DNS Server details:
DNS server IP ............................. 10.0.17.31
DNS server IP ............................. 10.0.17.43
Assisted Roaming Prediction List details:
Client Dhcp Required: False
Allowed (URL)IP Addresses
(Cisco Controller) >
(Cisco Controller) >show wlan 2
WLAN Identifier.................................. 2
Profile Name..................................... Demo1x
Network Name (SSID).............................. Demo1x
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Enabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Radius-NAC State............................... Enabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
--More-- or (q)uit
Number of Active Clients......................... 1
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ Disabled
Sleep Client..................................... disable
Sleep Client Timeout............................. 12 hours
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... mario-test-flex-vwlc
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
mDNS Status...................................... Disabled
mDNS Profile Name................................ unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
--More-- or (q)uit
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
--More-- or (q)uit
Radius Servers
Authentication................................ 10.0.16.111 1812
Accounting.................................... 10.131.16.111 1813
Interim Update............................. Disabled
Framed IPv6 Acct AVP ...................... Prefix
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Disabled
--More-- or (q)uit
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Enabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
--More-- or (q)uit
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
Eap-params.................................... Disabled
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Split Tunnel (Printers).......................... Disabled
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
--More-- or (q)uit
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
Local Policy
Priority Policy Name
(Cisco Controller) >
when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
(Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
*spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
MAC: 00:24:d6:97:b3:be, source 4
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 apfMsEapType = 13
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255, IPv
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255,
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 pmkLen = 32
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
type = Airespace AP Client - ACL passthru
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 A
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
*DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
Can you see any obvious reason why the NAC agent wont pop up?
Thanks
Mario -
Cisco WLC 2500 - 802.1x with Vasco Radius SMS OTP
Hello folks,
I have what seems to be a complex implementation with many things that need to be done on a customers network and I wanted to be pointed in the right direction.
The current scenario is such, the customer has a Cisco WLC 2500 device that has 3 access points(these are in the same AP group) connected to it. There is one SSID that I will call PRODUCTION here that some domain users use to connect to the local network. The customer has requested to have a GUEST SSID added to the WLC where guest users will connect to and recieve a SMS OTP for authentication.
Correct me if I am wrong, but I will obviously need to segment the SSIDs to have them running on different subnets to ensure that guest users do not have access to the production network once they authenticate. In order to do this I will need to configure Dynamic VLAN assignment for the Cisco WLC and connect it to a 802.1x port on the switch.
Now what is not clear is I am not interested in authenticating the users that connect via "Production SSID" and want to bypass authentication for those users and have them assigned to the default vlan (or maybe perhaps have them authenticate via LDAP on the AD), however I want to force the "GUEST" SSID users to authenticate so that they may recieve an SMS OTP (reason for this is to force guests to register their phone numbers to use the internet so that Illegal activity may be tracked).
1)So would it be possible to bypass authentication(or authenticate them via LDAP) for the PRODUCTION SSID as only domain users would know the SSID password to log on and have them by default assigned to the production subnet (default vlan) but force the GUEST SSID users to another VLAN via 802.1x sms otp?
2)*Important* Another issue that is not clear is will I be able to directly configure AAA Radius settings on the Cisco WLC to directly authenticate with the VASCO Radius OTP and recieve a challenge-response(required for OTP) during authentication? As I have seen from Ciscos Dynamic VLAN assignment docuementation (http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml) additional IETF Radius Perimeters are used such as Tunnel-Private-Group-ID etc are used which I can't seem to configure on the Vasco.
I do beileve this is a great project in helping me understand the INs and OUTs of CISCO WLC as well as Wireless NAC, If anyone could enlighten me and point me in the right direction I would be forever in debt. Much appreciated.
Best Regards
Sinan Barghouthi - JNCIA-FWV , JNCIA-IDP , CCA-NS , TCSM-8.0On your WLAN you can enable AES and TKIP. Just know that some clients mau have issue when they see both TKIP and AES. Ive had pretty good success with this in the past. Dont forget, you also need to enable WMM allowed to get N rates.
But you will need to configure AES on the client as well to support N rates.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection." -
Cisco WLC 7.5 Anchor w/Bonjour/Airplay AppleTV
Good Morning everyone,
I'm trying to get a 5508 (foreign) and a 2504 (anchor) on 7.5 to work with AirPlay. It's a single SSID/subnet, nothing to fancy other then the anchor. The anchor is providing the wlan for internet access, while the clients (ipad mini and appletv) are connected via wireless on ap off of the foreign controller.
In mDNS, I can see the Apple-TV.local. being advertised on the foreign controller, but the Ipad does not pick it up.
Anchor/DMZ Controller WLAN Config:
Very basic: wpa2-psk, AVC Profile, WMM, Bronze QoS, Aironet IE, mDNS Snooping ON, mDNS Profile default-mdns-profile.
Interface set for mDNS Profile default-mdns-profile
Foreign Controller WLAN Config
Very basic: wpa2-psk, AVC Profile, WMM, Bronze QoS, Aironet IE, mDNS Snooping ON, mDNS Profile default-mdns-profile. (tried with this off on foreign)
Interface set for mDNS Profile default-mdns-profile (tried with this off on foreign, as it's not the same vlan since it's anchored to a dmz controller)
AppleTV lattest greatest (wireless)
Ipad Mini 7.03 (wireless)
Any ideas?while the clients (ipad mini and appletv) are connected via wireless on ap off of the foreign controller.
//Apple TV should be WIRED on Anchor WLC.
Setup:
w.less ipad client(guest wlan map to mgmt)---AP---Foreign=====Anchor(guest wlan map to vlan10)---switch(Access vlan10)---ATV(wired)
http://www.cisco.com/en/US/docs/wireless/technology/bonjour/Printer_Services.html#wp1056055 -
I have a Cisco WRV210 wireless router that wont boot correctly after enabling WMM, problem is that after I enabled WMM and router rebooted I only see the power led and DMZ led on but not the wireless led and Internet led. I tried using the reset switch several times and nothing worked. Should I dispose of it and buy a new router or is this one still repairable?
Alvaro,
Please call support since the router is still under warranty.
www.cisco.com/go/sbsc
- Marty -
CSCum49200 - 7.6 Broadcom client connectivity problems if WMM enabled w/ ap2600
I have this issue when using Apple Macbook Pro in my network.
I have seen in thsi forum this problem occurs only with 3600 APs, but i`m having this same problem using 2602 APs.
can someone tell me if this is the same problema and if i cansolve this disbling the WMM?
RgsI too am having a connection problem with Apple Macbook Pro (2013 retina) and Cisco WAP 2602.
I am running 7.6.110.
I have not tested disabling WMM.
I really need a fix for this!!! -
We have cisco 5508.
We had problems with the connection of the first and second iPad version. Firmware: 7.0.235.3. Putting firmware 7.x. we can not because we have a point of 1310. But we put the firmware 7.2 ipad still have not get wireless. Then we rolled back. It is interesting that not only work the first and second iPads. All the above works. Played with TKIP instead of AES, did not help ...
P.s. iphone works.(Cisco Controller) >show wlan 45
WLAN Identifier.................................. 45
Profile Name..................................... Test
Network Name (SSID).............................. Test
Status........................................... Disabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 6400 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ guestwifi
Multicast Interface.............................. Not Configured
--More-- or (q)uit
WLAN ACL......................................... unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver (best effort)
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
--More-- or (q)uit
Accounting.................................... Global Servers
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Local Authentication................... Disabled
H-REAP Learn IP Address....................... Enabled
Client MFP.................................... Optional but inactive (WPA2 not configured)
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
--More-- or (q)uit
SIP CAC Fail Send Dis-Association Policy......... Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Mobility Anchor List
WLAN ID IP Address Status -
Is Cisco ever going to address the fact the E1200 does not support Wireless-N speeds at all!
When is Cisco ever going to address despite the touted speeds on their product packaging and what they claim wherever they sell the product that the E1200 with latest or earlier firmwares do not support Wireless-N speeds and usually gets under 1Mbps which is ridiculous?
Why is Cisco still selling this inferior product if they know it doesn't work and they have not patched it?
http://homecommunity.cisco.com/t5/Wireless-Routers/E1200-very-slow-wireless/td-p/492752/page/5
http://homecommunity.cisco.com/t5/Facebook-Support/E1200-Slow-connection/td-p/466164Extremely high volumes of connections can affect the speed of your own Internet connection. Did you already verify the connection straight to the modem? If that is working fine, then I firmly believed router is the issue here. Well there is lot of factors affecting slow speed with the router, that maybe cause by a corrupted firmware. BTW, what’s the version number of this router? If it’s already on the latest firmware, what I can suggest is to reset and reconfigure this device. You might as well disable WMM (it’s recommended for version 2 having this issue). My friend and I fix her problem with version when we disable WMM.
Maybe you are looking for
-
'D' Value in UPDMOD field getting lost in Transformation,Delete not working
Hello all, We are using this datasource 0PU_IS_PS_32 for Funds management, the datasource has UPDMOD field in it, which is basically the 0RECORDMODE. So when they delete the document on R/3 side we can pick up the delete. Now this is what is happenin
-
Header and footer display too narrow in IE
I'm working on a client website and have finished the basic template layout for all my pages. Everything displays beautifully in Safari, Opera, and Firefox, but in IE both the header and footer are narrower than the container. My header uses a backgr
-
HT201342 change apple id on my iPad
how i can change appl id on my ipad?
-
How to connect MBP to MacAir in target
My cursed 15" 2011 MBP has had a disk fail and won't boot. I tried repairing from a disk but it said to back up my files and reinstall. I have a MacAir but is there a way to connect the MBP to the MacAir in target mode so I can run a back up? I know
-
Time Machine incorrectly reporting free space
I'm seeing this on Mavericks (retina MBP, 500GB SSD about 60% utilized) . I've got a AFP network share that I copied a clean 800GB sparesebundle to. I use Disk Utility to mount and verify it, and it says, 650MB used, which means it's essentially 99%