Cisco RV320 with USB Dongle Quanta Computer - TELSEC TS-1K6 (TIM - Brazil)
Sorry for my bad English. I'm from Brazil.
Please, add support in the CISCO RV320 to USB Dongle Quanta Computer - TELSEC TS-1K6 (TIM - Brazil).
This dongle is very popular in Brazil.
Thanks
idVendor 0x0408 Quanta Computer, Inc.
idProduct 0xea49
bcdDevice 0.00
iManufacturer 1 QUANTA
iProduct 2 Mobile Broadband
Similar Messages
-
W701 Won't boot with USB dongle attached
W701 with current BIOS (6KET46WW v1.12) will hang if there is a USB dongle for a Microsoft Explorer Mouse USB dongle in the upper left USB (2.0) socket on boot. Works fine if you put the USB dongle in the lower USB/eSata socket. Note that the upper socket on this 2541-W1Z is NOT a USB 3.0 port (silver, not blue). Course I don't want to put it in that socket since I like to use that for eSata... Apparently the same problem exists in the W5XX laptops as well, but I don't see a post discussing the issue on the W701.
Have you seen the thread
Hangs on boot with Logitech wireless keyboard
Yours may be a similar problem.
I'm about to get a W701 in a day or 2 and will be in the same situation. I'll check it out and report back when I can.
ThinkPad W701 25002LG, i7 2Ghz,FX 3800M, 4Gb,16GB, SSD 320GB, DVDRW, RGB WUXGA, Wacom, Col Sensor, Fingerprint reader, Mini Dock -
Printer will only work connected with USB direct to computer
A few weeks ago I was printing a long document. In the middle of it, it went on hold. Since then I cannot print wireless with either of my computers. If I plug the USB direct from the printer to the computer the printer will work. I cannot print wireless. Do I need a new Airport?
Welcome to the discussions!
+Do I need a new Airport?+
Try a simple reset of the printing system as follows:
Make sure that the printer is plugged into the AirPort Express and everything is powered up
Open System Preferences on the dock and click Print & Fax
Right-click or control-click in the area where you see the printer listed
Select Reset Printing System
Click the + button
Highlight your printer on the available printer list
Click Add
Does that provide any help? -
IPOD charges when connected with USB cord, the computer doesn't recognize
I have an IPOD 4GB nano, when I connect the USB to the IPOD, it charges but the computer doesn't recognize it, itunes wont automatically start nor does it even show up on itunes. My other IPOD works fine with the cord. I tried the nano with another cord and still has the same problem. I tried resetting the nano, i've checked the usb ports...PLEASE HELP!
Sorry for your difficulty. Might be better to post here though:
http://discussions.apple.com/forum.jspa?forumID=826
Good luck,
Steve M. -
IPOD charges when connected with USB cord, the computer doesnt recognize
I have an IPOD 4GB nano, when I connect the USB to the IPOD, it charges but the computer doesn't recognize it, itunes wont automatically start nor does it even show up on itunes. My other IPOD works fine with the cord. I tried the nano with another cord and still has the same problem. I tried resetting the nano, i've checked the usb ports...HELP!
Sorry for your difficulty. Might be better to post here though:
http://discussions.apple.com/forum.jspa?forumID=826
Good luck,
Steve M. -
Windows 7 Pro
When I plug in IPad USB to computer and ITune I get this error message; Itune could not connect to this IPhone. An unknown error occurred (0xE8000084.Have you tried the troubleshooting on this page : iOS: Unknown error containing '0xE' when connecting to a Windows PC ?
-
Cannot print or scan with USB printer over wifi from airport express / time capsule wifi
Hi everybody,
I have recently set up time capsule connected to the router from the telephone company but created a new wifi network for the time machine to better work. Now I have bought an airport express to be able to use my USB printer over the WIFI network. I have to laptops, the printing works fine over the mac book air but not over the macbook pro. On top of that I cannot scan with either of the devices.
I have scanned most of the information out there but this issue seems not to be addressed properly anywhere. Advices given do always repeat itself but no solution worked for me.
Now I have plugged the usb from the printer directly back into mac book pro and the problem seems to persist here too. The message I receive everywhere is this one:
The software for the printer was installed incorrectly.
Would you like it to be repaired?
When I hit the Repair button a notice says 'repairing permissions' but nothing really happens. In the end nothing has been printed.
Resetting the printing systems has not really changed anything either. The problems persist.
This is the screen I get when the printer is directly plugged in through USB:
Result: printer recognised and installed, I cannot print (The software for the printer was installed incorrectly), but I can scan (probably because of the hint ('multifunction')
When I try to install the printer through the network connection (wifi network over time capsule and airport express) I get this image:
Result: printer recognised over bonjour but without multifunction (in other words without scanning), I cannot scan nor print (The software for the printer was installed incorrectly)
As I already mentioned any solution I found online would not work. Now the qustions are:
1) why can't I print? The drivers seem to be there but somehow broken, and I don't know how to repair it
2) why can't I scan over wifi? It sould possible that any function that can be performed over cable should also be able to performable over air, right?
I would very much appreciate any kind of help.
Thank you in advance,
CrisWhat's up doc?
HP has not provided "network" drivers to allow advanced features when the the All-in-One is connected to the USB port on the Time Capsule.
Therefore, only the printing function is supported when the All-in-One is connected to the Time Capsule's USB port.
If you need advanced features like fax, copy, scan, maintenance etc., you will need to connect over the WiFI network, or connect the All-in-One directly to your computer. -
How do I export the MUSIC in a playlist to a USB dongle?
Hi There,
I have put more than 400 songs into a new playlist and I want to export this playlist (music content NOT just the play LIST) onto a USB dongle. I did this some time ago and can't remember how I did it. I can BURN to a disk, but I want this playlist onto a dongle. Any help would be grateful.
Thanks
Phacoman.Hello arrowepark,
Thank you for providing the details of what you are trying to accomplish. To transfer a playlist, you will need to transfer the music and playlist file separately.
You can transfer your music by dragging the music to the USB drive, and next, you will have to take the additional step of exporting the playlist to the USB and importing your playlist to the alternate computer:
Transferring playlists
If you want not only your content but also your playlists to exist on your new computer, you will want to transfer a copy of all your playlists from your old computer. To do this, choose File > Library > Export Library on your old computer. Save the XML file that is created to your desktop.
Send the playlists file to yourself as an e-mail attachment, use an external drive, or use file sharing to move the playlists file to your new computer. Once the file is on your new computer, open iTunes and choose File>Library> Import Playlist. The import process will remove any items from the playlists that you didn't share via Home Sharing.
You can find this in the section titled "Home Sharing" in the following article:
iTunes: How to move your music to a new computer
http://support.apple.com/kb/HT4527
Thank you for using Apple Support Communities.
Best,
Sheila M. -
Problems with USB device when using WindowsNT
Hi,
my problem is that I want to use a simulator which can only be connected with USB to the computer.
I used the VISA Driver Development Wizard as discribed in this link (http://zone.ni.com/devzone/conceptd.nsf/webmain/6792BAB18242082786256DD7006B6416) and it didn't work.
I'm using Windows NT and VISA 3.1 and I read that it isn't possible to create a USB connection with VISA when using Windows NT. So my questions
1) is this right
2) Has someone a idea what I can do? I tried to use VISA USB Control and this also didn't work.
I hope I discribed my problem detailed enough. It's my first post.
Thanks for your responses
JoergAs you can see in this table, USB is not supported by VISA under NT:
http://digital.ni.com/public.nsf/websearch/EE34F21ECC2BE01286256C52005D1A1F?OpenDocument
I would recommend to use Win2000 or XP. Using one of these OSes you could use this turorial to create your VISA-driver:
http://zone.ni.com/devzone/devzoneweb.nsf/Opendoc?openagent&1D0DD81FF1448CAE86256D90006EE2B4
If it is not posssible to change the OS, you have to look for other ways of programming your usb-device. Check the web or the Microsoft site for help concerning Windows SDK and USB.
Hope this helps a little! -
View image instantly on monitor from camera with USB connection
Hello,
What I want is to see my image instantly on monitor when I am taking a picture from example a portrait or a painting in the studio. The camera is connected with USB to the computer.
Help!!So I was shooting teathered the other day with the following:
Nikon D100
USB to Powerbook G4, 1.25 Ghz 2GB Ram OS 10.4.8
Nikon Capture to Hot Folder
Hot Folder to Aperture
My issue was that sometimes for reasons I could not work out my
Camera would lock-up after a couple of frames shot. I was also syncing
to a couple of dynalites but I dont think it was a light re-cycle thing.
This became embarrasing as my subject was standing there and my shutter
would be locked up.
Was this an issue with maxing out the processor on the Pbook?
Or perhaps writing the file to aperture?
Would it be better to have the image display in Nikon Capture and worry bout importing into Aperture later?
After finally de-teathering and shooting normaly I never ran into the problem again.
Any thoughts appreciated.
TIA.
G5 Dual Core, AL 15" Pbook, G4 Quicksilvr, G3 Wallsteet, PM 9600, Mac SE Mac OS X (10.4.8) iPods: Nano, 4th-Gen & 1st-Gen 5Gb Original Goodness! -
Cisco RV320 DUAL WAN router USB setup with Telstra 4G MF823
I am trying to setup Cisco RV320 DUAL WAN router to work with my prepaid Telstra 4G MF823 device. Could you please assist. My settings are as follows: InterfaceUSB2Connection Type:3G/4G PIN Code:Confirm PIN Code:USB Connection Status:3G/4G modem is not available.Access Point Name:telstra.internetDial Number:Username:Password:Enable DNSDNS Server (Required): 8.8.8.8DNS Server (Optional): 8.8.4.4MTU:AutoManualB
Hi oz000,
Unfortunately we don't have anyone here to assist with this particular issue. Our team here provides assistance for the device standalone, we ensure that the 4G device connects to the network and functions correctly on its own.
-Matt W
-
Good Bluetooth USB Dongle on a computer with no built in Bluetooth?
Hi Everyone
What is a good external USB dongle to use to link up my new Apple bluetooth keyboard and magic mouse on my Mac Pro without built in Bluetooth?
ThanksProbably most any usb bluetooth dongle will work. I use a IOGear GBU421 (got it on sale at Fry's for about $9) but I believe the DLink DBT-120 is another populer one. Mine is plugged into the back of my 27" LED so it's only a foot or two away from my magic mouse and trackpad.
Note, there are a few "gotchas" with these things.
1. They are usb devices so if you sleep the machine the dongle is off too. So you can't, for example, click a bluetooth mouse to wake your machine. I wake my machine by clicking a key on my wired keyboard.
2. They don't always pair right away after waking up from sleep (at least mine doesn't). You may have to flip the switch on the mouse to get your machine to notice it. There is rarely a problem with the BT coming up after a (re)boot.
3. Depending on the model of mac pro, there may be some concern on whether plugging in a BT dongle disables the internal BT. On late 2010 Mac Pro's like I have it does. On earlier models I am not so sure and the internal card may have to be disconnected. Since you don't have internal you don't have to worry about this. I'm just mentioning this for others that may read this.
I guess I should answer the question on why one would stick a dongle onto a mac pro that has internal BT. Mainly because for some, the BT on the mac pro s**ks! IMO sticking an antenna inside and near the back of what amounts to a Faraday cage is not a bright idea. End result, skipping mice (google it and see this thread and there could be other dongle suggestions in that thread as well), poor reception, and a lot of frustration. Results vary depending on how far the mac pro is from the mouse, it's position, and what's between the back of the machine and the mouse.
4. Even if you use a BT mouse (with or without a dongle) I recommend always having a wired mouse as a backup (keboard too if you are using a BT keyboard).
5. If you are having pairing problems, the "standard" first attempt to fix is to do a smc and pram reset. And if all else fails you can do a "factory reset" of BT and re-pair your BT devices. -
Cisco vpn connect problem with 3g dongle
Hi,
I am trying to connect cisco vpn but every time i am getting following error while trying to connect from huawei 3g usb dongle in win8. for win7 it works fine with no issue. Also the problem is only form datacard, form lan and wireless interaface i can easily connect to vpn without any issue. Any help/idea/suggestion highly appreciated?
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
25 08:06:46.846 12/25/13 Sev=Info/4 CM/0x63100002
Begin connection process
26 08:06:46.848 12/25/13 Sev=Info/4 CM/0x63100004
Establish secure connection
27 08:06:46.848 12/25/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "116.68.208.113"
28 08:06:46.849 12/25/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 116.68.208.113.
29 08:06:46.855 12/25/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
30 08:06:46.858 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 116.68.208.113
31 08:06:47.145 12/25/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
32 08:06:47.145 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
33 08:06:52.144 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
34 08:06:52.144 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
35 08:06:57.144 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
36 08:06:57.144 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
37 08:07:02.145 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
38 08:07:02.145 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
39 08:07:07.145 12/25/13 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=97205EA6A12866F0 R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
40 08:07:07.645 12/25/13 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=97205EA6A12866F0 R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
41 08:07:07.645 12/25/13 Sev=Info/4 CM/0x63100014
Unable to establish Phase 1 SA with server "116.68.208.113" because of "DEL_REASON_PEER_NOT_RESPONDING"
42 08:07:07.645 12/25/13 Sev=Info/5 CM/0x63100025
Initializing CVPNDrv
43 08:07:07.645 12/25/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 0.
44 08:07:07.645 12/25/13 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
45 08:07:08.146 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
46 08:07:08.146 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
47 08:07:08.146 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
48 08:07:08.146 12/25/13 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
49 08:19:59.202 12/25/13 Sev=Info/4 CM/0x63100002
Begin connection process
50 08:19:59.202 12/25/13 Sev=Info/4 CM/0x63100004
Establish secure connection
51 08:19:59.202 12/25/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "116.68.208.113"
52 08:19:59.202 12/25/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 116.68.208.113.
53 08:19:59.202 12/25/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
54 08:19:59.218 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 116.68.208.113
55 08:19:59.656 12/25/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
56 08:19:59.656 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
57 08:20:04.656 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
58 08:20:04.656 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
59 08:20:09.656 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
60 08:20:09.656 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
61 08:20:14.656 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
62 08:20:14.656 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
63 08:20:19.656 12/25/13 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=46B8917FD54C64AC R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
64 08:20:20.156 12/25/13 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=46B8917FD54C64AC R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
65 08:20:20.156 12/25/13 Sev=Info/4 CM/0x63100014
Unable to establish Phase 1 SA with server "116.68.208.113" because of "DEL_REASON_PEER_NOT_RESPONDING"
66 08:20:20.156 12/25/13 Sev=Info/5 CM/0x63100025
Initializing CVPNDrv
67 08:20:20.156 12/25/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 0.
68 08:20:20.156 12/25/13 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
69 08:20:20.156 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
70 08:20:20.156 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
71 08:20:20.156 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
72 08:20:20.156 12/25/13 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stoppedHi Karsten,
Thank you for the reply !!! & best wishes for the new year 2014.
The problem is like this, if i select datacard connection type to NDIS it works but it doesnt work when i select RAS(modem) connection type for 3G datacard it doesnt. (NDIS and RAS(Modem) connection types are the 2 modes currently supporetd by the datacard.). Is there any case the users are experiencing from the similar problem? and what they have done to solve the issues? And thank you for the workaroung, i have checked the shrew-soft with win7 and it was working fine but not on win8, i will check shrew-soft on win8 very soon. Also we can move to the anyconnect solution but just want to know if this can solve our problem or not? whether there will be any issues with anyconnect solution for win 8 or not? can you please confim.
Thank you -
PXE boot tablet with Used USB dongle
We are running SCCM 2012 R2 Single Primary Site Server.
We are using the dongle (USB) to PXE boot the tablet computer.
We have advertised the Task Sequence to All Unknown Computer.
Once we use the USB dongle to image computer 1 , then the MAC address of USB dongle gets associated with the computer name of the tablet because the tablet does not have Ethernet port.
Now to image computer 2 if we PXE boot with used dongle gets PXE abort as it is known computer.
If we advertise to "All Known" computers then try the PXE boot works and we can image computer2 .
Now how can we advertise task sequence to "All Unknown" computers and get the task sequence to work with used USB Dongle.I suggest going back and reading it again then.
Highlight:
A “better” solution could be to create a collection, that is based on the Mac Address of the devices, which are used to deploy those systems. So typically this collection will have a handful of Mac Addresses. Important part is, that those Mac addresses
shouldn’t be used in day to day business, just for the plain purpose of deployment. Then one can advertise as many task sequences as required and limit the deployment(s) to only media and PXE. This way, the deployment isn’t visible from the Software Center
but the support staff can continue to deploy new systems using PXE or other medias like USB Sticks.
Don't retire TechNet! -
(Don't give up yet - 12,830+ strong and growing) -
How do i let my iphone connect to my computer wifi with usb ?
As the title stated,
How do i let my iphone connect to my computer wifi with USB ?
The reason is because my iPhone 3Gs wifi having some problem. So i have to use a USB cable to connect to my computer and let my iphone to connect to the internet .
If i don't do this i would have to keep on running out & in to my room & my living room.
My iPhone 3Gs allows to connect to the wifi when i am in my living room, but once i enter my room the wifi won't be able any more. So please help me out please people
I'm not sure about why i can't connect to my Ad hoc even it's so near, but i can connect to my router if i am in living rooms.
Regards,I believe the next time you sync your phone to itune via the cord, you will have to check the box that says sync via wifi and also enable that setting on your iphone.
Maybe you are looking for
-
Anyone know which render format I should use, my film will be used on a video wall (12 screens) and I need super quality. My footage format is 1080p HD resolution 1920x1080. I will be running the project from a mac with a direct line to video wall. T
-
Using MBP video out with with 2 adapters
I have the an early 2011 MBP (15'', 2.2GHz, 10.6.8). This video output connector this computer has is a MiniDisplay port (Thunderbolt digital video output). I often need to connect it to a projector at college. Most of these projectors still use seri
-
Locking a chart down on a page?
I'm working in Pages '09, version 4.3. I've created a bar-graph chart for a document, and every time the document is passed between my co-author, my editor and me, the chart's legend drifts away and ends up on another part of the page. The text insp
-
Does LabVIEW under Mac OS X support the PCI-MIO-16XE-50?
Or indeed any PCI DAQs for that matter? Thanks!
-
Safari stalls internet when using Facebook
I recently purchased a Macbook for college and after setting the laptop up, I easily connected to our locked wireless within the house. It has been working perfectly fine in every room in the house, but when I log in to facebook.com and look at my pr