Cisco Server VCS C220 M3 Server BIOS password issue

We have a Cisco Server VCS C220 M3 Server BIOS password issue.
We needed to turn on Bit locker in the Cisco Server VCS C220. To do this we needed to create an administrator password for the BIOS to turn on trusted Platform Module (TPM). After we set up the administrator password and turn on Security for TPM. We were prompted for the administrator password. It would not let us log in with the administrator password that we created for the BIOS. In the next few days we received a BIOS is corrupted screen (BIOS Flash Image Corrupted *****).We follow procedures to recover the BIOS with the USB stick with recovery .cap file in the root folder. We tried reseating the jumper pg. 35 of the Cisco Server VCS C220 M3 Server of the Installation and Service Guide.
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C220/install/C220.pdf
We were able to bring up the server, but we are still not able to get pass the Admin password issue. We tried to clear the CMOS header with Header J37 page 2-18 but we had no success with clearing out the password prompt. Figure 2-6 Service Header Locations shows the J41 BIOS RCVR boot and J37 Clear CMOS.
Can anyone provide us documentation of where the pins are located on the motherboard to clear the BIOS password? We are looking for more of a detail picture of the pins please. The documentation is only showing a basic diagram of the header locations.

You need to look at the CUCM logs for further info on what might have happened, and to make sure your servers are fit for the amount of users, devices, etc. you have in your environment.

Similar Messages

BIOS Password Issue

I recently had Toshiba replace the hard drive on a C55-B5270 that was under warranty. When I got it back I used it for one day and turned it off. When I turned it back on that night, the enter BIOS Password screen appeared and nothing I've tried to remove it worked. Per Toshiba's instructions I had a local tech try to fix it but he can't get access to the right part. It is a Windows 8.1. So I called Toshiba and they blame me and act as if this never happens and is not covered under warranty.

Satellite C55-B5270
I recently had Toshiba replace the hard drive on a C55-B5270 that was under warranty. When I got it back I used it for one day and turned it off. When I turned it back on that night, the enter BIOS Password screen appeared...
Just after receiving a repaired machine?
I wonder if Peter from Toshiba could help you with that. I'll flag him down.

BIOS password issue on Tecra A9

My laptop Toshiba Tecra A9 have a problem with the BIOS password and I was wondering if you could provide me the password since I can not access anything without it

BIOS password is very important security feature and such issues cannot be clarified on public forum.
All problems with BIOS password must be clarified with Toshiba service provider.
If your notebook is blocked by password and you cannot access it please contact nearest Toshiba service and they can remove it for you.

Hp elitebook 2560p bios password issue

how to remove bios password on hp elitebook 2560p,

Rahul.
There are no master password generators for ProBooks or EliteBooks and most business class laptops.
You will need to contact HP.
http://www8.hp.com/us/en/contact-hp/ww-contact-us.html?jumpid=reg_r1002_usen_c-001_title_r0003
Or look at this link.
http://forums.mydigitallife.info/threads/49497-HP-Probook-Elitebook-BIOS-Password-Reset-Utility
Or replace the BIOS chip.
http://www.ebay.com/itm/HP-Elitebook-8460p-8460w-8560p-8560w-8760w-2560p-2760p-Bios-Chip-No-Password...
REO
I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damage that may arise to your system by using these services. Please be aware that you do this at your own risk.
HP Expert Tester "Now testing HP Pavilion 15t i3-4030U Win8.1, 6GB RAM and 750GB HDD"
Loaner Program”HP Split 13 x2 13r010dx i3-4012Y Win8.1, 4GB RAM and 500GB Hybrid HDD”
Microsoft Registered Refurbisher
Registered Microsoft Partner
Apple Certified Macintosh Technician Certification in progress.

UEGEN Z830 BIOS Password

I have a Z830, i forgot my BIOS password, how can reset or clear this BIOS password? i can not start my laptop without this password.
i called Toshiba repair center the said BIOS password issue is how cover by warranty, if i want to have it fix i have to pay over 100 dollars ..... PLEASE HELP THANKS to every one..

It can only be removed by having it serviced unfortunately.
- Peter

Equium A100-338 BIOS Password

Hi all,
At first I want to tell, that my problem is fixed. I have A100 model and I was very happy since Feb 2007 when I bought it. I'm security maniac, so I putted passwords for everything: BIOS user, BIOS administrator, HDD, and few others :) Anyway, everything was OK until... my password wasn't working any more. I'm 100% sure about user, and admin password. So I tried reset BIOS and I took of battery for two days. Of course for nothing ;)
So I called Toshiba Support and very nice person said, that this laptop will be collected from me, fixed, and then they will send it for me completely free. That was only because I bought extension warranty for three years.
Laptop is fixed and now I have problem: put passwords again or no? This is the Question!
I know, that this problem is with few models more too:
Link: [Passwords errors in Toshiba laptops|http://ie.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/faq_selection.jsp?service=IE|Passwords errors]
So what if password will crash again? Without any reason? And what?
Have I send it every time to ASP and have I wait for three days?
I need my laptop for work as well, so maybe Toshiba can fix it *PERMANENTLY* on every laptop?

Hi
I searched in the Toshiba knwowledg base mentioned in your message above but I didnt find any articles about the BIOS password issue on A100 notebook.
I found some articles about Tecra A3 or Satellite A80 and this should be fixed by BIOS update.
Regards

C220 m3 server stuck in bios

I keep geting stuck in a loop wen setting up the c220 m3. I updated all the drivers and rebooted the server but keeps coming back here.
any idea?
thanks

Tony,
Actually the server is not stuck in BIOs, it is getting to the HUU utility cause very likely the FlexFlash has the HUU partition active.
You can do thi, go to Server> Inventory> Storage> Select the FlexFlash and clicki on "Configure Operational Profile", it will show you something like the image attached:
*SCU= Server Configuration Utility
*Drivers
*HV= Useful if you want to have a Hypervisor installed in this FlexFlash partition
*HUU= This is the screen you are getting when the server boots up.
Enable/Disable this options accordingly, disable of all them if you want to boot from the local disk.
I hope this helps
-Kenny

Problem with Cisco Bars after Database Republish ("Could not find Cisco Unified database on this server")

OS Version: 2000.4.3a
OS Service Release: 2000.4.5bSR21
OS Upgrade: 2000.4.5a
Bars Version: 4.0.15000
CUCM Version: 4.2(3)sr4b
During the upgrade process of our CUCM 4.2(3) to version CUCM 4.2(3)sr4b the database replication between our 2 servers (1x pub, 1x sub) failed. After fixing this via dbhelper tool (everthing´s green and smiling again) service seemed to be ok.
But now Cisco Bars does not work anymore. The backup process of the publisher fails with "Error=[Microsoft][ODBC SQL Server Driver][SQL Server]Login failed for user '(null)'. Reason: Not associated with a trusted SQL-Server connection." So it looks like some kind of database setting for bars is misconfigured after the republishing process.
Yesterday I tried to reinstall BARS (now in the newest version 4.0.150000), but the same error message occured. Now I get the message "Could not find Cisco Unified database on this server" when I try to configure the Backup source within BARS.
Curiously the backup of our second CCM (sub) works as expected (but without CDR and TFTP Data). The "BackAdmin" User exists and is not locked (and wasn´t changed manually at all).
I am runnig out of ideas... :-(
Any hint or idea on how to fix this is kindly appreciated
best regards
Michael

Mike,
I don't have anything definitive here but I am wondering if there is a discrepency between the database names. In SQL Enterprise Manager, you can go to the Publisher and see what the current database name is. It will be the one being replicated and will take the form of CCM0300 or CCM0301 or CCM0302. You should see more than one. Anyway, take note of the name.
Then on the Publisher launch regedit and go to HKLM\Software\Cisco Systems, Inc.\DBL\
Look at the values for DBConnection0 and DBConnection1.
It will be something like DSN=CiscoCallManager;Server=;DATABASE=;Trusted_Connection=yes
Does the in the DSN match what you expect?
Also, going to back to SQL Enterprise Manager, check out the permissions on the database (Right Click->Properties, go to Permissions tab).
Another thing to check if you think it is permissions related is the AdminUtility.exe (c:\program files\cisco\bin\). This can be used to resync system account passwords.
TBH, I am just shooting in the dark here but these are things I would check.
Regards,
Bill

Problem with the new server UCS C220 for set IP to CIMC

Hi
We’ve a problem with the new server UCS C220.
We bought two servers UCS C220 M3 for CallManager 8.6 with High Availability.
When we turn on the server during the boot and when it tells us, oppress F8 to enter at the CIMC and set the IP. But it never enters at the CIMC.
Then, we configure our DHCP server and our switch, we connect the three gigabyte ports to our switch to give him an IP to the CIMC, so and then can enter via browser, but neither works.
Note. The dedicated management NIC does not link, the other two ports do make link.
What do you suggest to put an IP to CIMC and start installing our applications?
regards

You may have noticed that there is no DVD rom on the c220. What you need to do is:
Login into the CIMC from your browser
Luanch the KVM
Insert the VMware DVD in your machines drive
On the KVM pop up there should be a tab to mount the drive, after mounting it click on Macros and choose ctrl_alt+delete to restart.
After the VMware OS installs press F2 to enter IP.
Browse to the VMware ip to download the Vsphere client
Open the Vsphere client, enter the ip of the vmware and the username will be root and no password if you did not set one.
You can now upload OVA templates or manually create virtua machine from this enviroment.
Hope this help

Cisco PI 1.3 - Internal Server Error with RADIUS-authentication

Hi,
I have a problem with a Cisco Prime Infrastructure 1.3 (Appliance, fully patched) that I'm trying to authenticate against a Radiator RADIUS-server.
From the RADIUS-server's point of view it looks fine, but I just get an HTTP Status 500 internal error (see attached image) when trying to log in.
I'm not the one managing the RADIUS-server but I got the following debug sent from them:
Wed Oct 30 08:52:06 2013: DEBUG: Packet dump:
*** Received from 10.36.0.132 port 17235 ....
Code:       Access-Request
Identifier: 102
Authentic: REMOVED
Attributes:
        User-Name = "test-user"
        User-Password = REMOVED
        NAS-IP-Address = 10.36.0.132
        Message-Authenticator = REMOVED
Wed Oct 30 08:52:06 2013: DEBUG: Handling request with Handler 'Client-Identifier=/^prime[.]net[.]REMOVED[.]se$/', Identifier 'Network-Prime-AAA'
Wed Oct 30 08:52:06 2013: DEBUG: Deleting session for test-user, 10.36.0.132,
Wed Oct 30 08:52:06 2013: DEBUG: Handling with Radius::AuthUNIX:
Wed Oct 30 08:52:06 2013: DEBUG: Radius::AuthUNIX looks for match with test-user [test-user]
Wed Oct 30 08:52:06 2013: DEBUG: Radius::AuthUNIX ACCEPT: : test-user [test-user]
Wed Oct 30 08:52:06 2013: DEBUG: AuthBy UNIX result: ACCEPT,
Wed Oct 30 08:52:06 2013: DEBUG: Handling with Radius::AuthFILE:
Wed Oct 30 08:52:06 2013: DEBUG: Radius::AuthFILE looks for match with test-user [test-user]
Wed Oct 30 08:52:06 2013: DEBUG: Radius::AuthFILE ACCEPT: : test-user [test-user]
Wed Oct 30 08:52:06 2013: DEBUG: AuthBy FILE result: ACCEPT,
Wed Oct 30 08:52:06 2013: DEBUG: Access accepted for test-user
Wed Oct 30 08:52:06 2013: DEBUG: Packet dump:
*** Sending to 10.36.0.132 port 17235 ....
Code:       Access-Accept
Identifier: 102
Authentic: REMOVED
Attributes:
        cisco-avpair = "NCS:virtual-domain0=ROOT-DOMAIN"
        cisco-avpair = "NCS:role0=Admin"
        cisco-avpair = "NCS:task0=View Alerts and Events"
        cisco-avpair = "NCS:task1=Device Reports"
..the rest of the AV-pairs removed
Does anyone have any idea on what the the problem is, or some tips on how to troubleshoot? (rebooting and ncs stop/start has no impact on the issue)
//Charlie

I ran into a similar issue this morning in my lab. After I issued ncs status - the database service came back as not running. I stop/started the Prime services and it came up. Once all the services were running my WLC imported with no issues. I also deployed another server for another lab and it had issues with the clocking being out of sync.

TS3899 cannot receive or send email from my hotmail account, refuses to verify server. I have changed my password, deleted the account numerous times, any solutions? all on ios 6.

cannot receive or send email from my hotmail account, refuses to verify server. I have changed my password, deleted the account numerous times, any solutions? all on ios 6. it was working up until a few days ago and now refuses to load on both my ipad 2 and iphone 4S
in the process deleted all my contact, very annoying.
all help is much appreciated.
interesting that my gmail account does work perfectly.

this may or may not help - but give it a try. On a forum some were reporting that talk21 is now under the yahoo umbrella. below are the steps this use listed. (This was an android forum, but the email settings should be the same. In short it looks like their server names have changed. An existing account may have simply been forwarded - but if you are reinstalling, it may want a clean install to the right servers.) Pay particular attention to the server names and port settings. (this thread was started based on a discussion of Imap vs pop - you are already an Imap person - so ignore that part)
See if this helps.
why settle for pop3, when IMAP works with talk21 and not only does mail get pushed out faster with IMAP, but when you click refresh it will be received faster than pop3. The other advantage is subfolders are also supported with IMAP but cant be seen with POP3. This mail feature works with my android eclair & hero phone and the settings are exactly the same for win mobiles also (not tested). The mail setting up roadmap is the same from what i can remember once in the mail feature for win mobi.
This is what you need to do to setup Talk21 email with IMAP.
Incoming server settings
IMAP server - imap.mail.yahoo.com
Port - 143
Security type - none
Outgoing Server settings
SMTP server - smtp.mail.yahoo.com
Port - 25
Security type - none Also important note - Enable 'require sign-in'
and enter your talk21 username and password The End...works a treat for me p.s. Its only taken me 3 years to work it out with win mobile and recently with android. Finally got it to work...hope this helps all the talk21 users out there. if there are any other similar posts out there with no answer...dont forget to mention my name when passing this post around.

I suddenly cannot email photos from iphoto. I get a box that says "server does not recognize username or password". I now have to use regular email and cannot re-size my photos.

Suddenly I can no longer email photos directly via iphoto mail. The box comes up that says "server does not recognize username or password". I used to be able to re-size my photos before sending so that they jpeg or pixels were larger for publishing in newspapers or magazines, but I can no longer do that. Apple tech support told me to change my iphoto "preferences" to using regular email to send. But that does not allow me to re-size. Is anyone else having this problem? I don't know if there was an update that caused this or what? Please help.

The box comes up that says "server does not recognize username or password".
That error message usually will pop up, when there is a conflict between the "From" setting for the mail account you are sending from and the selected outgoing mail server. Probably the outgoing Mail server is receiving a user name and password it does not understand. When the mail returns unsent, do you see the "Try again" panel with the option to select a different outgoing mail server?
If you do not see this panel, change the Mail "Preferences > General" to "If Outgoing server is unavailable: Show a list of alternate servers". This way, you will know, which server Mail is trying to send from.
Have you tried to set "From" pop-up menu to one of your other email addresses? If that works, change your settings in Mail to always send from this address. You can set this option in the Mail "Preferences > Composing: Send New Messages from". I have my "Send New Messages from" set to "iCloud". That is working best for me with iPhoto.

How can I automatically connect to the server without having to type the password and click "connect"?

I have a Mac OS X 10.8 and a Time Capsule configurated as server with a name "Servidor" on my home. The discs are protected by Accounts, so, each person can access the server by typing own name and password. The problem is... Every time I start the computer, I see the window below:
So, every time I start I have to type my name and pass. And the box "Remember this password on my keychain" doesn't work because the "Password" is always blank when I see the window, like the image up.
Please, someone help me to automatize it so I don't need to type nothing to connect to the server. I want something that do it automatically for me.
NOTE: Please, explain clear and with details because I'm a new Mac's user.
Thank so +!

Try running KeyChain First Aid if you have not already done so.
Open Keychain Access and click on the KeyChain Access menu at upper left of the screen
Click KeyChain First Aid, then close KeyChain Access
Open System Preferences (gear icon on the dock)
Open Network
Click on AirPort or WiFi on the left
Click Advanced at the lower right
Click to highlight an old network that you no longer need, then click the - (minus) button to delete the listing
Do the same for other neworks that you no longer need
Make sure there is a check mark in the box that reads "Remember networks this computer has joined"
No other boxes should be checked.
Click OK, then click Apply
That is about all that you can do.

I've recently changed my password on my e-mail account and now I can't share i photos instead I get a message The email server didn't recognize your username/password combination. How do I change it in i photo pls

I've recently changed my password on my e-mail account and now I can't share i photos instead I get a message The email server didn’t recognize your username/password combination. How do I change it in i photo pls

I'm trying to email from iPhoto

Problem on installing Solaris 10 on Cisco UCS-C24-M3S2 rack server.

I've got issue on installing Solaris 10 on Cisco UCS-C24-M3S2 rack server. Solaris 10 doesn't recognize UCSC-RAID-ROM55.

Hi dipaktimsina,
From the documentation below it looks like Solaris doesn't have support for the embedded raid controller with the ROM55 chip.
http://www.cisco.com/web/techdoc/ucs/interoperability/matrix/matrix.html
let me know if you have any questions and don't forget to rate any useful answers.

Cisco Server VCS C220 M3 Server BIOS password issue

Similar Messages

Maybe you are looking for