Cisco SF300 Switch

Dear All,
I am going to purchse  SF 300 24p POE Switch and could anyone tell me if this Switch supports the configuration via console ?
As i have ESW-500 Sieries switches and it doesnot support console !
Please give me the  answer for this question !
Thank you in advance !
Best Regards,
Giorgi

Hello,
Not everything a 2950 can do, because then why buy a 2950?
But it can do a lot. here is a link to the spec sheet.
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps10898/data_sheet_c78-610061.html
Cisco Small Business Support Center
Randy Manthey
CCNA, CCNA - Security

Similar Messages

  • Cisco Small Business Office Manager and SF300 switched

    Hello
    As I saw the the office manager cann't manage SF300 switches, what alternative do we have ?

    Yes, this will work.  I have it up and running.  Use the site to site vpn wizard on the ASA and then on the WRVS4400N, make sure to select the settings below.  *You need to disable PFS on the ASA either during the wizard of afterward under vpn properties/advanced.
    Phase 1 >
    Mode = IKE w/ Preshared Key
    Encryption = 3DES
    Auth = SHA1
    Group = 1024 bit
    key lifetime = 86400
    Phase 2 >
    Encryption = 3DES
    Auth = SHA1
    PFS = Disable
    Group = 1024 bit
    key lifetime = 3600

  • Cisco SF300-24: Searching OIDs

    Hello all,
    I've got a Cisco SF300-24 and would like to monitor trough snmp:
    - Memory Used, Free
    - Interface CRC
    - cpu utilization
    - Memory Buffer Used
    I checked your website related technical documentation for the Cisco MIB file, and the two species are listed below
    •1.     Cisco Small Business 300 Series Managed Switch Administration Guide Release 1.2.5.PDF
    •2.     SRW-US_v10_UG_A-Web. PDF
    •3.     Sx300_MIB_1.1.2.ZIP
    And I could not confirm that such OID values
    Don't its  hard to find the right OIDs.
    Could someone help me please?
    Thanks in advance

    Hi,
    I believe the device you mentioned is the IOS based device. If it is so then you may use following MIBs depending on the version of IOS.
    Memory statistics via CISCO-ENHANCED-MEMPOOL-MIB and CISCO-MEMORY-POOL-MIB
    http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a95.shtml
    CPU statistics via CISCO-PROCESS-MIB and OLD-CISCO-CPU-MIB
    http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a94.shtml
    Interface CRC via OLD-CISCO-INTERFACES-MIB (specifically "locIfInCRC"). If you want to get the interface related statistics then you have to go for IF-MIB.
    You may refer to following links additionally if you want help with some FAQs.
    http://www.cisco.com/en/US/tech/tk648/tk362/tk605/tsd_technology_support_sub-protocol_home.html
    http://www.cisco.com/en/US/tech/tk648/tk362/technologies_q_and_a_item09186a0080094bc0.shtml
    http://www.cisco.com/en/US/tech/tk648/tk362/technologies_q_and_a_item09186a00800c2612.shtml
    Regards
    K. Lakshmi Ganesh

  • Trunk SF300 switch with a 3750

    Is it possible to trunk a SF300 switch with a 3750 switch?  If so how?  Whenever I turn trunking on the 3750 port I lose connection to the SF300.
    I would appreciate any assistance, thanks
    Larnel

    Here's some sample config that I've got.  In the version of OS on the SF 300 right now, you can't acces the LCLI, but you can tftp backup/restore it;
    ! On the SF 300;
    ! Note that VLAN 111 is my native/untagged VLAN and the management VLAN here
    ! The 20x VLANs are 802.1q trunk/tagged
    ! Remember that there is no VTP here, so you must manually create the VLANs first
    interface range ethernet g(1-4)
    description "Uplink trunk"
    exit
    interface range ethernet g(1-4)
    switchport default-vlan tagged
    exit
    vlan database
    vlan 111,200,201,202
    exit
    interface range ethernet g(1-4)
    switchport trunk allowed vlan add 200
    exit
    interface range ethernet e(21-24)
    switchport access vlan 201
    exit
    interface range ethernet g(1-4)
    switchport trunk allowed vlan add 201
    exit
    interface range ethernet g(1-4)
    switchport trunk allowed vlan add 202
    exit
    interface range ethernet g(1-4)
    switchport trunk native vlan 111
    exit
    interface vlan 111
    ip address 10.111.0.5 255.255.255.0
    exit
    interface vlan 1
    no ip address dhcp
    exit
    ! On the Cisco IOS switch;
    Switch1#sh run int Gi2/0/19
    Building configuration...
    Current configuration : 334 bytes
    interface GigabitEthernet2/0/19
    description whatever-bla-bla-bla
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 111
    switchport trunk allowed vlan 111,200,201,202
    switchport mode trunk
    switchport nonegotiate
    end

  • Cisco SF300-24 IP Configuration Issue

    Hi,
    I have purchased Cisco SF300-24 few days before. I have created 3nos of new Vlan. I am not able to assign IP to each Vlan.
    When ever I aggign the IP to the next vlan, previouly assigned ip is not visible.
    need help.

    Hello,
    Do you have the switch in Layer 2 or Layer 3 mode.  In layer 2 mode the switch can have only one IP address.  This can either be static or DHCP.  The switch must be in layer 3 mode to assign IP addresses to each VLAN.  Please see page 258 of the admin guide for how to set IP address for each VLAN.  If you need to set to layer 3 please see page 61.  Also, please make sure your device is on the latest firmware version 1.3.0.59.  If you still have trouble try using a different browser.  I tried this using Firefox and experienced a similar issue to what you describe.  I switched to IE9 and it worked fine.
    If you have completed these steps and are still having difficulties please call the Cisco SBSC at 866-606-1866 between 9am and 6pm your local time for further assistance.
    ~Mike Vandergrift
    SBSC Engineer

  • Uplink two Cisco SF300 swicthes through SFP

    Hi,
    I'm stuck in the following situation. I have:
    Two SF300 Switches (SRW224G4P-K9-EU)
    Two Gigabit Ethernet SX Mini-GBIC SFP Transceivers (MGBSX1)
    Two 3 mtr Fiber cables LC -> ST (50FIBLCST3 StarTech)
    Two ST Connectors (715297 st fiber connector)
    The purpose is to use the SFP ports as an uplink between the two switches.
    Now, using the SFP ports on both Cisco Switches, connecting through the fiber cable....it looks like the switches aren't connected. :-( Do I miss anything? The System Summary using the GUI control panel of one of the switches do not show any activaty on the SFP ports. Any help would be nice!

    Hi Tim, if you want to prove the wire and SFP is any good, take a transmit and transmit (or receive and receive) end together in the same GBIC and connect it to one of the switch ports. This should make a loopback detect condition and the port should turn green with activity lights.
    *Note, if the fiber has a clipholding the TX and RX together you may have to remove the clip or if the clip is fixed you may need to break it.

  • Difference between Linksys SRW224G4 & Cisco SF300-24

    Hi Guys
    I was wondering if there was a difference between the Linksys SRW224G4 & Cisco SF300-24 switches. Going through the support docs I see the SF300 has limited L3 functionality in terms of being able to establish static routes between VLANS. Any further information would be of use.
    Also any recommendations for an equivalent switch for access layer/distribution layer use would be most welcome
    Thanks
    GR

    SF300-24 is a brand new product with vast improvements over SRW224G4. Here's a few of the major ones:
    1)    1) Overall Value:
    -          > 80 New software features:
    o   Layer 3 Routing for improved network performance where multiple VLANs are used
    o   IPv6 support to protect investments as you evolve your network to the Next Generation Internet
    o   Advanced VLAN Services enabling new application support (Voice VLAN, Guest VLAN, MAC-based VLAN, Protocol-based VLAN, Dynamic VLAN assignment)
    o   Advanced Security – Denial of Service Attack prevention, Protected ports, Private VLAN Edge
    o   Unique things to Cisco - like CDP, Auto Smartports, CCA, FindIT - deliver simplified management and autodiscovery
    o   Others including Energy Efficiency, IGMP Querier, LLDP-MED, Time-based 802.1x, etc
    -          Numerous hardware enhancements
    o   Energy-efficient technology, helping save power and reduce costs
    o   Fanless designs on many models for silent operation
    o   Advanced and latest silicon with larger memory and flash footprints deliver confidence in this state of the art solution 
    -          More ports per Gigabit switch. In the case of low density (10 port), equates to 25% more ports. With 24-port switches, 16% more ports
    -          Very competitively priced – in most cases below comparative competitive products while delivering more capabilities
    2)     2) Unique Cisco Value deliver simplified management and autodiscovery – CDP, Smartports, CCA, FindIT
    3)   3) Lifetime Warranty with Next Business Day Advanced Replacement (where available) and lifetime warranty on power supplies and fans
    4)     4) Localization into seven languages - English, German, French, Italian, Spanish, Simplified Chinese, and Japanese

  • VLAN trunking from Cisco Catalyst 3750 to Cisco SF300-48P issue and related

    Hello expert,
    I'm having difficulties to configure VLAN trunking between Cisco Catalyst 3750 switch with Cisco SF300-48P switch and my workstation unable to get any DHCP IP from our DHCP server via Cisco SF300-48P switch. Below is the snippet of configuration on both switches:
    [Cisco Catalyst 3750 Switch]
    interface GigabitEthernet1/0/45
     description NCC-CC-1stFlr
     no switchport trunk encapsulation dot1q
     no switchport trunk allowed vlan 101-103
     spanning-tree portfast
    [Cisco SF300-48P Switch]
    interface fastethernet48
     spanning-tree link-type point-to-point
     switchport trunk allowed vlan add 101-103
     macro description switch
     !next command is internal.
     macro auto smartport dynamic_type switch
    interface fastethernet29
     switchport mode general
     switchport general allowed vlan add 103 tagged
     switchport general pvid 103
    Are these are correct? Kindly advice!
    Thank you very much!
    Regards,
    Alex

    Hi Alex,
    for the trunk port on Catalyst on port GE 1/0/45, we need to enable the trunk and for on encapsulation dot1q because this catalyst model is ISL capable also and the SF300 working only with Dot1q Encapsultion
    The configuration on catalyst should :
    #config terminal
    #interface Gi 1/0/45
    # switchport encapsulation 
    #switchport trunk encapsulation dot1q
    #switchport mode trunk 
    #switchport trunk allowed vlan 101-103
    #spanning-tree portfast
    For SF300 the port trunk it looks fine but for the port where the PC should receive an IP address
    #interface fastethernet29
     #switchport mode access
     #switchport ccess vlan 103
    Please let me know after this configuration
    Thanks
    Mehdi
    Please rate or mark as answered to help other Cisco Customers

  • Trunking on Cisco SF300 Issue

    Hello Friends,
    Issue: I have 3 Cisco SF300 multilayer switches, I have configured one switch as a core switch and changed the mode to Router (from layer2 to Layer3) and configured Vlans and DHCP pools accordingly, but when i am trying to connect another SF300 to this switch by using VTP it's giving error then i tried searching a solution and found that it does not support VTP protocol, can someone please help me on that, how i can connect other SF300 to this core switch by using trunking.
    My goal is to connect the Switch1 and Switch2 to the CoreSwitch by using trunking so that CoreSwitch can advertise all Vlan information to Switch1 and 2. and PC connected to Switch1 & 2 on different Vlans can communicate to each other.
    Network Diagram:
    CoreSwitch fast-Ethernet port 1 to 8 are connected to Huwai Router Port 1 to 8 using a dedicated physical enter phase to connect each Vlan to the internet. using Nat overload.   CoreSwitch's fastethernet Port 9 to 24 are disabled, gigabit port 1 to 4 are trunk port and allowed vlan are 11, 12,13,14,15,16,17 and 20.
    Note: All 3 switches are in Layer3 mode.
    CoreSwitch Gigabit ethernet Port1 connected to = Switch1 gigabit ethernet port 1 
    CoreSwitch Gigabit ethernet Port2 connected to = Switch2 gigabit ethernet port 2
    Switch1 Gigabit ethernet Port4 connected to = Switch2 gigabit ethernet port 4
    Configuration:
    CoreSwitch:
    User Name:cisco
    Password:XXXXXXX
    Welcome to CoreSwitch.
    Regards,
    Sandy
    CoreSwitch#show run
    config-file-header
    CoreSwitch
    v1.3.7.18 / R750_NIK_1_35_647_358
    CLI v1.0
    set system mode router
    file SSD indicator encrypted
    ssd-control-start
    ssd config
    ssd file passphrase control unrestricted
    no ssd file integrity control
    ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
    spanning-tree priority 0
    vlan database
    vlan 11-17,20
    exit
    voice vlan oui-table add 0001e3 Siemens_AG_phone________
    voice vlan oui-table add 00036b Cisco_phone_____________
    voice vlan oui-table add 00096e Avaya___________________
    voice vlan oui-table add 000fe2 H3C_Aolynk______________
    voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
    voice vlan oui-table add 00d01e Pingtel_phone___________
    voice vlan oui-table add 00e075 Polycom/Veritel_phone___
    voice vlan oui-table add 00e0bb 3Com_phone______________
    gvrp enable
    ip dhcp excluded-address 192.168.11.1 192.168.11.2
    ip dhcp excluded-address 192.168.12.1 192.168.12.2
    ip dhcp excluded-address 192.168.13.1 192.168.13.2
    ip dhcp excluded-address 192.168.14.1 192.168.14.2
    ip dhcp excluded-address 192.168.15.1 192.168.15.2
    ip dhcp excluded-address 192.168.16.1 192.168.16.2
    ip dhcp excluded-address 192.168.17.1 192.168.17.2
    ip dhcp pool network CashOfficedepo
    address low 192.168.12.1 high 192.168.12.254 255.255.255.0
    default-router 192.168.12.1
    dns-server 192.168.20.3 192.168.20.4
    exit
    ip dhcp pool network Churn5StarPayrollWeb
    address low 192.168.11.1 high 192.168.11.254 255.255.255.0
    default-router 192.168.11.1
    dns-server 192.168.20.3 192.168.20.4
    exit
    ip dhcp pool network Commission
    address low 192.168.13.1 high 192.168.13.254 255.255.255.0
    default-router 192.168.13.1
    dns-server 192.168.20.3 192.168.20.4
    exit
    ip dhcp pool network Inventory
    address low 192.168.15.1 high 192.168.15.254 255.255.255.0
    default-router 192.168.15.1
    dns-server 192.168.20.3 192.168.20.4
    exit
    ip dhcp pool network Managers
    address low 192.168.17.1 high 192.168.17.254 255.255.255.0
    default-router 192.168.17.1
    dns-server 192.168.20.3 192.168.20.4
    exit
    ip dhcp pool network ReportingAccount
    address low 192.168.14.1 high 192.168.14.254 255.255.255.0
    default-router 192.168.14.1
    dns-server 192.168.20.3 192.168.20.4
    exit
    ip dhcp pool network TechDept
    address low 192.168.16.1 high 192.168.16.254 255.255.255.0
    default-router 192.168.16.1
    dns-server 192.168.20.3 192.168.20.4
    exit
    bonjour interface range vlan 1
    hostname CoreSwitch
    snmp-server location
    snmp-server contact
    clock timezone " " 0 minutes 0
    ip name-server  202.XXX.XXX.XXX       
    ip telnet server
    interface vlan 1
     ip address 192.168.10.3 255.255.255.0
     no ip address dhcp
    interface vlan 11
     name Churn5StarPayrollWeb
     ip address 192.168.11.1 255.255.255.0
    interface vlan 12
     name CashOfficedepo
     ip address 192.168.12.1 255.255.255.0
    interface vlan 13
     name Commission
     ip address 192.168.13.1 255.255.255.0
    interface vlan 14
     name ReportingAccount
     ip address 192.168.14.1 255.255.255.0
    interface vlan 15
     name Inventory
     ip address 192.168.15.1 255.255.255.0
    interface vlan 16
     name TechDept
     ip address 192.168.16.1 255.255.255.0
    interface vlan 17
     name Managers
     ip address 192.168.17.1 255.255.255.0
    interface vlan 20
     name SERVERS
     ip address 192.168.20.1 255.255.255.0
    interface fastethernet1
     switchport trunk allowed vlan add 11
    interface fastethernet2
     switchport trunk allowed vlan add 12
    interface fastethernet3
     switchport trunk allowed vlan add 13
    interface fastethernet4
     switchport trunk allowed vlan add 14
    interface fastethernet5
     switchport trunk allowed vlan add 15
    interface fastethernet6
     switchport trunk allowed vlan add 16
    interface fastethernet7
     switchport trunk allowed vlan add 17
    interface fastethernet8
     switchport trunk allowed vlan add 20
    interface fastethernet9
     shutdown
    interface fastethernet10
     shutdown
    interface fastethernet11
     shutdown
    interface fastethernet12
     shutdown
    interface fastethernet13
     shutdown
    interface fastethernet14
     shutdown
    interface fastethernet15
     shutdown
    interface fastethernet16
     shutdown
    interface fastethernet17
     shutdown
    interface fastethernet18
     shutdown
    interface fastethernet19
     shutdown
    interface fastethernet20
     shutdown
    interface fastethernet21
     shutdown
    interface fastethernet22
     shutdown
    interface fastethernet23
     shutdown
    interface fastethernet24
     shutdown
    interface gigabitethernet1
     gvrp enable
     switchport trunk allowed vlan add 11-17,20
    interface gigabitethernet2
     switchport trunk allowed vlan add 11-17,20
    interface gigabitethernet3
     switchport trunk allowed vlan add 11-17,20
    interface gigabitethernet4
     switchport trunk allowed vlan add 11-17,20
    exit
    banner login ^C
    Welcome to CoreSwitch.
    Regards,
    Sandy
    ^C
    banner exec ^C
    Welcome to CoreSwitch.
    Regards,
    Sandy
    ^C
    ip default-gateway 192.168.11.2   (huwai router's fast ethernet port1 ip address)
    ip default-gateway 192.168.12.2   (huwai router's fast ethernet port2 ip address)
    ip default-gateway 192.168.13.2   (huwai router's fast ethernet port3 ip address)
    ip default-gateway 192.168.14.2   (huwai router's fast ethernet port4 ip address)
    ip default-gateway 192.168.15.2   (huwai router's fast ethernet port5 ip address)
    ip default-gateway 192.168.16.2   (huwai router's fast ethernet port6 ip address)
    ip default-gateway 192.168.17.2   (huwai router's fast ethernet port7 ip address)
    ip default-gateway 192.168.20.2   (huwai router's fast ethernet port8 ip address)
    CoreSwitch#
    =====================
    Switch1: no configuration yet (Tried configuring VTP but got no luck, it's not supported so i turned on the GVRP...running RSTP and spanning-tree priority is 4096)
    =====================
    Switch2:  no configuration yet.....
    Thanks,
    Sandy

    Please find the below mentioned show vlan output of both the Switches  :
    CoreSwitch#show vlan
    Created by: D-Default, S-Static, G-GVRP, R-Radius Assigned VLAN
    Vlan       Name                   Ports               Created by
     1           1             fa1-24,gi1-4,Po1-8             D
     11  Churn5StarPayroll          fa1,gi1-4                 S
         Web
     12   CashOfficedepo            fa2,gi1-4                 S
     13     Commission              fa3,gi1-4                 S
     14  ReportingAccount           fa4,gi1-4                 S
     15      Inventory              fa5,gi1-4                 S
     16      TechDept               fa6,gi1-4                 S
     17      Managers               fa7,gi1-4                 S
     20       SERVERS               fa8,gi1-4                 S
    AccessLayer1#show vlan
    Vlan       Name                   Ports                Type     Authorization
     1           1             fa1-24,gi1-4,Po1-8        Default      Required
    AccessLayer1#
    I just wondering that i have enabled GVRP on both side and made them trunk then why Switch1 is not showing me the Vlan i created on CoreSwitch :(
    Thanks,
    Sandy

  • Packet loss when pinging from/to a cisco 3560e switch

    I see Packet loss when pinging from/to a cisco 3560e switch. CPU utilization is normal.
    Switches are running with IOS c3560e-universalk9-mz.122-35.SE5.bin.
    Packet loss is observed for all the devices irrespective of directly connected or remote devices.
    If i do self pinging, there are no packet loss.
    I don't see any error on interface.
    Can anyone please help me in resolving this issue.

    TCB       Local Address           Foreign Address        (state)
    03737C48  10.47.0.229.60053       10.41.81.55.49         CLOSEWAIT
    039ACDC4  10.47.0.229.61929       10.41.35.250.49        CLOSEWAIT
    03B316C0  10.47.0.229.27544       10.41.81.55.49         CLOSEWAIT
    038228F0  10.47.0.229.16506       10.41.35.250.49        CLOSEWAIT
    039C3D04  10.47.0.229.15207       10.41.81.55.49         CLOSEWAIT
    039A9BD0  10.47.0.229.52983       10.41.81.55.49         CLOSEWAIT
    0394152C  10.47.0.229.22425       161.61.35.250.49       CLOSEWAIT
    037D811C  10.47.0.229.21117       10.41.81.55.49         CLOSEWAIT
    039C12BC  10.47.0.229.37437       10.41.81.55.49         CLOSEWAIT
    03933B84  10.47.0.229.34085       161.61.35.250.49       TIMEWAIT
    03B32340  10.47.0.229.45729       10.41.81.55.49         CLOSEWAIT
    038247D0  10.47.0.229.32816       10.41.81.55.49         CLOSEWAIT
    039A92D8  10.47.0.229.38680       161.61.35.250.49       CLOSEWAIT
    037370F0  10.47.0.229.13212       10.41.81.55.49         CLOSEWAIT
    037D85F0  10.47.0.229.38728       10.41.81.55.49         CLOSEWAIT
    03B2B284  10.47.0.229.23428       10.41.81.55.49         CLOSEWAIT
    03B2ADB0  10.47.0.229.56836       10.41.81.55.49         CLOSEWAIT
    0394BFF0  10.47.0.229.23257       161.61.35.250.49       CLOSEWAIT
    036604DC  10.47.0.229.44437       10.41.81.55.49         CLOSEWAIT
    0394C700  10.47.0.229.22          192.37.184.211.61639   ESTAB
    039B9A68  10.47.0.229.20543       10.41.81.55.49         CLOSEWAIT
    03739B28  10.47.0.229.15392       10.41.81.55.49         CLOSEWAIT
    TCB       Local Address           Foreign Address        (state)
    0392EA48  10.47.0.229.13862       10.41.81.55.49         CLOSEWAIT
    0365E23C  10.47.0.229.27856       10.41.81.55.49         CLOSEWAIT
    03817C0C  10.47.0.229.64929       10.41.81.55.49         CLOSEWAIT
    039357C8  10.47.0.229.22088       10.41.81.55.49         CLOSEWAIT
    037375C4  10.47.0.229.21832       10.41.81.55.49         CLOSEWAIT
    039C20E8  10.47.0.229.18169       10.41.81.55.49         CLOSEWAIT
    03716D08  10.47.0.229.61993       10.41.81.55.49         CLOSEWAIT
    039A74E4  10.47.0.229.62948       10.41.81.55.49         CLOSEWAIT
    03655480  10.47.0.229.14052       10.41.81.55.49         CLOSEWAIT
    039407F0  10.47.0.229.49643       161.61.35.250.49       CLOSEWAIT
    039A53AC  10.47.0.229.13233       10.41.81.55.49         CLOSEWAIT
    03739FFC  10.47.0.229.16605       10.41.81.55.49         CLOSEWAIT
    039B82B8  10.47.0.229.16458       10.41.35.250.49        CLOSEWAIT
    039BEBA4  10.47.0.229.64377       10.41.81.55.49         CLOSEWAIT
    03741980  10.47.0.229.13866       10.41.81.55.49         CLOSEWAIT
    03B3ABF8  10.47.0.229.19365       10.41.81.55.49         CLOSEWAIT
    039B5810  10.47.0.229.24768       10.41.81.55.49         CLOSEWAIT
    03956E48  10.47.0.229.55980       161.61.35.250.49       CLOSEWAIT
    03946820  10.47.0.229.65053       161.61.35.250.49       CLOSEWAIT
    037DBE94  10.47.0.229.15283       10.41.81.55.49         CLOSEWAIT
    039A4854  10.47.0.229.48562       10.41.81.55.49         CLOSEWAIT
    TCB       Local Address           Foreign Address        (state)
    03B33320  10.47.0.229.29803       10.41.81.55.49         CLOSEWAIT
    03B3B79C  10.47.0.229.12142       10.41.81.55.49         CLOSEWAIT
    03713C9C  10.47.0.229.63799       10.41.81.55.49         CLOSEWAIT
    039BBECC  10.47.0.229.14763       10.41.81.55.49         CLOSEWAIT
    03656E40  10.47.0.229.16357       10.41.81.55.49         CLOSEWAIT
    0362A73C  10.47.0.229.62450       10.41.81.55.49         CLOSEWAIT
    039B878C  10.47.0.229.64402       161.61.35.250.49       CLOSEWAIT
    03826CFC  10.47.0.229.16108       10.41.81.55.49         CLOSEWAIT
    03B2CA34  10.47.0.229.17634       10.41.81.55.49         CLOSEWAIT
    03AD78D0  10.47.0.229.15249       161.61.35.250.49       CLOSEWAIT
    03AD967C  10.47.0.229.20389       161.61.35.250.49       CLOSEWAIT
    03B2C560  10.47.0.229.37079       10.41.81.55.49         CLOSEWAIT
    039C5128  10.47.0.229.24711       10.41.81.55.49         CLOSEWAIT
    03822F74  10.47.0.229.54866       10.41.81.55.49         CLOSEWAIT
    0372C5FC  10.47.0.229.13298       10.41.81.55.49         CLOSEWAIT
    0372D278  10.47.0.229.12407       10.41.81.55.49         CLOSEWAIT
    039A33D0  10.47.0.229.36573       10.41.81.55.49         CLOSEWAIT
    039BCEF8  10.47.0.229.53853       10.41.81.55.49         CLOSEWAIT
    039C02D8  10.47.0.229.53725       10.41.81.55.49         CLOSEWAIT
    039B5CE4  10.47.0.229.58027       10.41.81.55.49         CLOSEWAIT
    0381866C  10.47.0.229.17100       10.41.81.55.49         CLOSEWAIT
    TCB       Local Address           Foreign Address        (state)
    039BB374  10.47.0.229.53148       10.41.81.55.49         CLOSEWAIT
    03AD3634  10.47.0.229.19716       161.61.35.250.49       CLOSEWAIT
    0362DAA4  10.47.0.229.19479       10.41.81.55.49         CLOSEWAIT
    0365AE60  10.47.0.229.62209       10.41.81.55.49         CLOSEWAIT
    0362D5D0  10.47.0.229.41327       10.41.81.55.49         CLOSEWAIT
    037D7C48  10.47.0.229.58283       10.41.81.55.49         CLOSEWAIT
    03955474  10.47.0.229.33810       161.61.35.250.49       CLOSEWAIT
    0373B15C  10.47.0.229.23331       10.41.81.55.49         CLOSEWAIT
    036628D0  10.47.0.229.46856       10.41.81.55.49         CLOSEWAIT
    03819584  10.47.0.229.19861       10.41.81.55.49         CLOSEWAIT
    0394D000  10.47.0.229.64732       10.41.35.250.49        CLOSEWAIT
    0394B760  10.47.0.229.19967       161.61.35.250.49       CLOSEWAIT
    039B6BD4  10.47.0.229.40096       10.41.81.55.49         CLOSEWAIT
    03AD7150  10.47.0.229.65184       10.41.35.250.49        CLOSEWAIT
    039BC3A0  10.47.0.229.64702       10.41.81.55.49         CLOSEWAIT
    03B3A724  10.47.0.229.60399       10.41.81.55.49         CLOSEWAIT
    037145E0  10.47.0.229.43951       10.41.81.55.49         CLOSEWAIT
    03955EDC  10.47.0.229.29015       161.61.35.250.49       TIMEWAIT
    0365FB34  10.47.0.229.13961       10.41.81.55.49         CLOSEWAIT
    03828D54  10.47.0.229.12743       10.41.81.55.49         CLOSEWAIT
    037DB40C  10.47.0.229.23708       10.41.81.55.49         CLOSEWAIT
    TCB       Local Address           Foreign Address        (state)
    039AF814  10.47.0.229.15100       10.41.81.55.49         CLOSEWAIT
    0392E344  10.47.0.229.23399       10.41.35.250.49        CLOSEWAIT
    0393DC3C  10.47.0.229.15393       161.61.35.250.49       CLOSEWAIT
    03AD85D0  10.47.0.229.40932       161.61.35.250.49       TIMEWAIT
    039574CC  10.47.0.229.25935       10.41.35.250.49        CLOSEWAIT
    03738B74  10.47.0.229.58656       10.41.81.55.49         CLOSEWAIT
    039AD91C  10.47.0.229.56760       10.41.81.55.49         CLOSEWAIT
    03B3BC70  10.47.0.229.15058       10.41.81.55.49         CLOSEWAIT
    03B2DC54  10.47.0.229.51131       161.61.35.250.49       CLOSEWAIT
    03B393F0  10.47.0.229.11957       10.41.35.250.49        CLOSEWAIT
    039B2610  10.47.0.229.33728       10.41.81.55.49         CLOSEWAIT
    03B311EC  10.47.0.229.18047       10.41.81.55.49         CLOSEWAIT
    039A8E04  10.47.0.229.52022       161.61.35.250.49       CLOSEWAIT
    0365D460  10.47.0.229.12241       10.41.81.55.49         CLOSEWAIT
    03B33E78  10.47.0.229.47640       10.41.81.55.49         CLOSEWAIT
    0372C128  10.47.0.229.60323       10.41.81.55.49         CLOSEWAIT
    03661CD8  10.47.0.229.39923       10.41.81.55.49         CLOSEWAIT
    0393C73C  10.47.0.229.41864       10.41.35.250.49        CLOSEWAIT
    03829584  10.47.0.229.56673       161.61.35.55.49        CLOSEWAIT
    0362AC10  10.47.0.229.31952       10.41.81.55.49         CLOSEWAIT
    039BF078  10.47.0.229.22636       10.41.81.55.49         CLOSEWAIT
    TCB       Local Address           Foreign Address        (state)
    0365CF8C  10.47.0.229.14476       10.41.81.55.49         CLOSEWAIT
    039B443C  10.47.0.229.59226       10.41.81.55.49         CLOSEWAIT
    0393E794  10.47.0.229.56282       10.41.35.250.49        CLOSEWAIT
    03657740  10.47.0.229.25769       10.41.81.55.49         CLOSEWAIT
    03B2F6E8  10.47.0.229.19328       10.41.81.55.49         CLOSEWAIT
    0373AC88  10.47.0.229.25766       10.41.81.55.49         CLOSEWAIT
    039B213C  10.47.0.229.28882       10.41.81.55.49         CLOSEWAIT
    039C07AC  10.47.0.229.38201       10.41.81.55.49         CLOSEWAIT
    03AD8DD0  10.47.0.229.23002       10.41.35.250.49        CLOSEWAIT
    03739048  10.47.0.229.29572       10.41.35.250.49        CLOSEWAIT
    039BA464  10.47.0.229.32273       10.41.81.55.49         CLOSEWAIT
    03B31E6C  10.47.0.229.32521       10.41.81.55.49         CLOSEWAIT
    0365EBE0  10.47.0.229.41319       10.41.81.55.49         CLOSEWAIT
    03938804  10.47.0.229.62841       10.41.35.250.49        CLOSEWAIT
    039A1AF8  10.47.0.229.12758       10.41.81.55.49         CLOSEWAIT
    039B7DE4  10.47.0.229.20921       10.41.81.55.49         CLOSEWAIT
    036549F8  10.47.0.229.51903       10.41.81.55.49         CLOSEWAIT
    03714CC8  10.47.0.229.45145       10.41.81.55.49         CLOSEWAIT
    037425F8  10.47.0.229.56492       10.41.81.55.49         CLOSEWAIT
    03B39D74  10.47.0.229.18174       10.41.81.55.49         CLOSEWAIT

  • How to setup a static multicast ARP entry with Cisco SF300-08?

    We're running a cluster in multicast mode as a  loadbalancer.
    We have Cisco SF300-08 and when we adding a static ARP entry results in an error message telling the user that the hardware address needs to be a valid  unicast MAC address.
    So how to setup a static multicast in Cisco SF300 or maybe someone know other solution to setup multicastes mode in Cisco SF300.

    Hi, Tom!
    We have two watchguard xtm505(cluster active-active) in our network. Watchguard interfaces have one ip and one mac adresses. IP 192.168.111.1(Unicast) and MAC 01:00:5e:02:02:03(multicast).  Cisco SF300 is router to outside networks(to internet). Cisco IP adresss is 192.168.111.254. There are another some hosts in this network.
    Ping from hosts to 192.168.111.254 works well. Ping from hosts to 192.168.111.1 works well too.  But there is no ping from watchguard cluster(192.168.111.1) to Cisco(192.168.111.254). And there is no routing to internet
    This is well-known situation. We need to do following(example for cisco 3750):
    1.    Start the Cisco 3750 command line interface.
    2.    Add a static ARP entry for the multicast MAC address of the FireCluster interface.
    Type this command:
    arp arpa
    For this example, type:
    arp 192.168.111.1 01:00:5e:02:02:03 arpa
    3.    Add an entry to the MAC address table.
    Type this command:
    mac-address-table static vlan interface <#>
    For this example, type:
    mac-address-table static 01:00:5e:02:02:03 vlan 1 interface gi1/0/11
    But we can't add arp entry on Cisco SF300. CLI tells us "MAC address illegal"!
    We tried enable igmp snooping, but is not helps.
    Could you tell more detailed about MAC groups?

  • FC-2GB module part number for cisco 4503 switch

    Dear Sir,
    We hv a SAN switch MDS-9216 with FC-2GB ports.
    We want to connect the SAN switch to our newly installed cisco 4503 switch which modules is required in the cisco 4503 switch to connect the SAN switch FC-2GB ports.
    Regards
    Deepak

    Deepak,
    Can you explain why you want to do this?
    The Catalyst 4503 is an ethernet switch and does not support FC-2G interfaces. If you want to enable IP access to your storage, you would need an IP storage services module in your MDS 9216. This would then provide GE interfaces which you could connect to your Catalyst 4503. You could then provide IP-based hosts access to FC-connected storage using iSCSI for instance.
    Regards
    Rob.

  • Embeded Event Manager on cisco 3560 switch

    Can someone help me please? I have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. For some reason this configuration is not good and I can't tell why. I already try to debug this with debug event manager action mail but didn't see any output .
    ip sla 11
    icmp-echo ip address
    frequency 20
    ip sla schedule 11 life forever start-time now
    event manager applet device-TEST
    event snmp oid 1.3.6.1.4.1.9.9.42.1.2.9.1.6.11 get-type exact entry-op lt entry-val "2" poll-interval 20
    trigger occurs 5 period 120
    action 02.0 mail server "ip address" to "[email protected]" from "[email protected]" subject "device is down"

    The mail part looks good, I'm not sure you are hitting the trigger right.
    Why not do a track on the ip sla instead of the snmp stuff?
    Here's a good example of that.
    https://learningnetwork.cisco.com/blogs/network-sheriff/2009/06/19/writing-your-first-eem-applet

  • Converting Eth port to FC port in a cisco 6001 switch

    Hi,
    Back to forum after a long time. I have one issue to discuss regarding cisco 6001 switch. We purchased a new 6001 switch. Want to convert some of the Ethernet ports out of total 48 to FC to join the switch into a existing fabric.
    cisco Nexus 6001 Chassis ("Norcal 64 Supervisor")  - This is what H/W version look like from show version command.
    In the past, we have quite a few Cisco 5548UP switch and the way convert the Ethernet port into FC port is, by going to correct slot/module and then
    (config)# slot 1
    (config-slot)# port 41-48 type fc
    Then "reload" willl complete the conversion. But in the new 6001 switch, it throws the following error when above command is typed. We have full license for the switch including  FC_FEATURES_PKG
    "ERROR: Module type doesn't support this CLI"
    We are running firmware : 6.0(2)N2(2)
    Any help in this regard will be helpful.
    Thanks.

    I have this exact same error;
     show ver
    Cisco Nexus Operating System (NX-OS) Software
    TAC support: http://www.cisco.com/tac
    Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_series_home.html
    Copyright (c) 2002-2014, Cisco Systems, Inc. All rights reserved.
    The copyrights to certain works contained herein are owned by
    other third parties and are used and distributed under license.
    Some parts of this software are covered under the GNU Public
    License. A copy of the license is available at
    http://www.gnu.org/licenses/gpl.html.
    Software
      BIOS:      version 1.5.0
      loader:    version N/A
      kickstart: version 7.0(5)N1(1)
      system:    version 7.0(5)N1(1)
      Power Sequencer Firmware:
                 Module 1: version v4.0
                 Module 2: version v4.0
      Fabric Power Sequencer Firmware: Module 1: version v4.0
      Microcontroller Firmware:        version v1.2.0.5
      QSFP Microcontroller Firmware:
                 Module 2: v1.3.0.0
      SFP Microcontroller Firmware:
                 Module 1: v1.1.0.0
      BIOS compile time:       12/29/2012
      kickstart image file is: bootflash:///n6000-uk9-kickstart.7.0.5.N1.1.bin
      kickstart compile time:  10/29/2014 22:00:00 [10/30/2014 11:46:56]
      system image file is:    bootflash:///n6000-uk9.7.0.5.N1.1.bin
      system compile time:     10/29/2014 22:00:00 [10/30/2014 11:47:58]
    Hardware
      cisco Nexus 6001 Chassis ("Nexus 64 Supervisor")
      Intel(R) Xeon(R) CPU  @ 2.00 with 8238120 kB of memory.
      Processor Board ID FOC181506P3
      Device name: xxxxxxxxxxxxxx
      bootflash:    7823360 kB
    Kernel uptime is 3 day(s), 17 hour(s), 25 minute(s), 49 second(s)
    Last reset at 642096 usecs after  Fri Feb 27 15:24:40 2015
      Reason: Disruptive upgrade
      System version: 6.0(2)N2(3)
      Service:
    plugin
      Core Plugin, Ethernet Plugin, Fc Plugin
    xxxxxx# conf t
    Enter configuration commands, one per line.  End with CNTL/Z.
    xxxxxx(config)# slot 1
    xxxxxx# port 47-48 type fc
    ERROR: Module type doesn't support this CLI

  • Trouble with Windows7 and Gigabit link on Cisco 3560X switch

    Hello,
    In my company, we are using Cisco IP Phones 7945G (with 2 gigabit network ports) and Cisco 3560X-48P (1GB ports) switches for our users.
    Our client computers are running on Windows 7 SP1 (64bit - Enterprise edition) and are connected behind the IP Phone. We use a "Boradcom
    Xtreme Gigabit" onboard network card on the computers. All ports (on the switch site and IP Phone side) and on the network card of the computer are configured in "auto negotiation". Duplex and speed are set to "auto".
    We tried now to deploy a new engineering software and we are facing a very strange problem. This means that the engineer software fails to download some files from the server. We are using a flat network, all the servers and computers are on the same network segment with no firewall inbetween.
    The firewall and Anti-virus on the computers are configured to allow all incoming/outing connections.
    To troubleshoot, I tried to change all the network cables but I still get same result --> download fails.
    I connected the client computer directly to the Cisco 3560X switch, without the IP Phone and I get the same result.
    I installed a separate network card from INTEL (Intel PRO1000 PT) but I get the same result.
    As last test, I have connected to same client computer directly to a Cisco 2960-8TC switch (100Mbit; auto negotiate) and here is working fine. The software successfully downloads all the files from the server.
    If I connect the computer behind the Cisco 7945 IP Phone, set the speed and duplex of the PC-Port on the Cisco IP Phone 7945G to "100MBit/full duplex" is also working fine.
    Is there any know issue with Windows7 and Gigabit network connections?
    Do I need to set any Registry key on my Windows 7?
    The firmware version of my Cisco 3560X-48P switch is 12.2(53)SE2; do I need to update it?
    The firmware version of the IP Phone 7945G is 9.2.1.
    Thanks in advanced for your help.
    Marc Hoffmann

    Hello, Thanks for your answers. First of all, I have updated the firmware of my Cisco Catalyst 3560X-48P switch to the version 12.2(55)SE5. Unfortunately, this did not solve my problem. As second step, I ran an TDR test on my 3560X switch but I do not get any result. The "Pair status" always says "not completed". Even if I wait for 5 minutes, the status remains at "Not completed". Am I doing something wrong ? To do the TDR test, I use the commande "test cable-diagnostics tdr interface gigabitEthernet 0/XY". For your information, the port gigabitEthernet 0/XY is in a "Connected" status when I run the "show int status" command. Jeff, I think there is no issue on the server side, because if I connect my workstation on a 100MB switch (example Cisco Catalyst 2960-8TC-L) the application works absolutely fine. Also, if I run the application locally on the server, it works fine. As next step, I will connect the workstation directly on our backbone switch and try the same test. Is there perhaps any Registry key in our Windows7 which could cause this trouble? If you have any other ideas or options, please let me know. Thanks a lot, Marc Hoffmann

Maybe you are looking for

  • US Ipads in the UK?

    Hello all - I want to buy an Ipad while back in the US. Can I still use it without any compatibility issues/wireless problems here in the UK? Does it affect anything in regards to ease of use, connectivity, etc?

  • Viewing flash based website in HTML component of AIR APP

    Hello,  I've got an air app where I'm trying to use the Html component to load up a flash website.  Problem is that the website starts to load (I can see the preloader) and then the html component just goes blank.  I wrote the html page I'm trying to

  • JPub Error User-defined type not found

    I just have found about Jpub could help me with my problem, so i try it, but when i try to publish a package it gives me this error: J2T-118, ERROR: User-defined type "ADMCAD.PKG_CONSULTA_BR_NOME.TAB_ELEITOR" was not found in the database This is the

  • Streaming HTML

    One of the servlets my team maintains needs to output over 200 fields for several hundred records. Right now it takes awhile for the user to see anything because the entire HTML is created for all of the fields for all of the selected records before

  • Can't remember screen lock password

    can't remember screen lock password!