Cisco SPA514g Secure web interface only.

I have a Cisco SPA514g, I want to secure the web interface with a password. When I change the password and it reboots the phone comes up fine. On certain functions in now asks for the user password for example on redial. Is there a way to disable the security on these functions other than removing the password on the profile "user"?

Use the following document http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo1100/accsspts/i12213ja/i12213sc/s13web.htm to get access to the Web interface

Similar Messages

Cisco AP 1131AG Web Interface Problem

Hello,
I purchased two Cisco access points (model AIR-AP1131AG-A-K9) from a seller on eBay. The Access Points power up fine and are able to get an IP address (I can see the AP's MAC address on my router), but it won't let me connect to the web interface to manage it. I have tried using different browsers, but they all say something along the lines of "The page could not be found" when I enter the IP address into my browser. No login screen, no nothing: just a time-out error.
When the Access Points are powered on, the Ethernet and Radio lights start out green, but then the Ethernet light stays green and the radio light flashes amber and the two alternate being lit. The status light on the outside of the Access Point goes from green to orange to red and back again, looping infinitely.
Any ideas what could be wrong? Thanks for any and all help in advance! (Please let me know if you need more information; I don't ahve the AP's with me, but I will be home in a few hours and can respond then.)

do a show cdp neighbor detail on the port the AP is connected to. Take a look at the software that is running, IOS will show k9w7, and lightweight will show k9w8.
if it''s k9w8, you'll need to convert them back to IOS
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Lost The Cisco Aironet 1310 Web Interface????

I've been having connection issues with my (2) Aironet 1310, which are setup in a bridge p2p mode. A few weeks ago we had a power outage due to a lighting storm. Well, it knocked out my non-root bridge (not connecting to the root). So I brought it back to check the configurations, but when I try to use the web console all I get is the following page:
When I click the "Web Console" link it takes me to the following page:
Is there a way to get the original web console page back?

here is the command..
archive download-sw / force-reload /overwrite tftp:///
Example..
archive download-sw / force-reload /overwrite tftp:///c1310-k9w7-tar.124-21a.JA1.TAR
to get the .TAR, go to the folder where the image is saved and then Tools >> folder options >> view >> check >> show hidden files and folders.
Now click on the image and then copy the image name and then paste the same on the CLI... then this come as IMAGE.TAR that is.. c1310-k9w7-tar.124-21a.JA1.TAR instead of c1310-k9w7-tar.124-21a.JA1
it should be c1310-k9w7-tar.124-21a.JA1.TAR
lemme know how this works out for you!! if you face any difficulties while upgrading please open up a TAC case.. we wil solve this in less than 5 minutes... and the network wil be back up!!
Regards
Surendra

Cisco SA 520W Web Interface not loading.!!

Hi
Im going to start with saying this appliance is really winding me up!! The unit has been working fine for a while and i now need to make some changes. The unit is passing traffic fine, URL filtering is working fine however when i load the web page to control it says "The server is down.
Connection failed " I have rebooted the device numerous times with no luck. I have tried a different laptop, cleared out cookies and all ie cash. tried a different browser. To no avail. Am loosing faith in this device
Any ideas

Hi accidentexchange,
Did you fail to log in when accessing the SA 520W thru both HTTP and HTTPS?
https://LAN_IP_address_of_SA520W/
http://LAN_IP_address_of_SA520W/
Furthermore, can you give us an overview of your network topology and user info. If possible, can you provide us the configuration and dbglogs from your SA 520W so that I can forward to the development team?
To get the dbglog from SA520W, login through web UI and in the browser enter the following URL:
https://LAN_IP_address_of_SA520W/scgi-bin/dbglog.cgi
These logs will store password, so please remove any password sensitive information. Also if you are not comfortable posting the dbglog on the community, you can send it directly to me through private message.
Cheers,
Julio

Web Interface of Cisco Prime 2.1 not working

Excuse me!
I install the trial version cisco prime 2.1 (OVA) on ESXi server
I can ping cisco prime but web interface of cisco prime not worinking
prime/admin# ncs status
Health Monitor Server is running.
Ftp Server is running
Database server is running
Tftp Server is running
Matlab Server is running
NMS Server is running.
Plug and Play Gateway is running.
SAM Daemon is running ...
DA Daemon is running ...
Syslog Daemon is running ...

Services running fine..
check it with other Browser , Supported browser are below::
–   Google Chrome 31 or later.
–   Microsoft Internet Explorer 8.0 or 9.0 with Google Chrome Frame plugin (users logging in to the simplified Lobby Ambassador interface do not need the plugin).
–   Mozilla Firefox ESR 24.
–   Mozilla Firefox 24, 25 or 26.
If above does not help , reboot the server once and check the issue again.
Thanks-
Afroz
***Ratings Encourages Contributors ****

Privileged Exec password works for telnet but not web interface on Cisco AP 1242

I recently configured a Cisco AP 1242, software version 12.4, via the web interface using the default Cisco credentials. At that time I setup an administrator account with read/write access and changed the Cisco to a read only access. Now went I attempt to login to the web interface it won't accept the administrator password. It will except the administrator password in a telnet session however. So via the telnet session I setup another user with privileged exec level access and that wont work on the web interface either. The Login box keeps coming back requesting a password. Strangely enough, I can login to the web Interface using admin username, with the Cisco password; but I can't do anything, and I also can't view everything.
I've tried the following:
I've turned on SSH and created a certificate in the AP, but the login box continues to pop on the https://url.
I've attempted to setup a user with a non-encrypted password, but have been unsuccessful.
I've tried a different browser - login box continues to pop.
I've made sure the web interface is activated in the AP
I've tried a differnet computer
I've tried disabling password-encryption service
Reset the enable password
I've successfully setup other 1240 APs but must have done something wrong on this one. Anyone know what I'm missing? Thanks.
Solution: I was missing "ip http authentication local" in my config.

Solution: I was missing "ip http authentication local" in my config.

WVC54GCA Missing WPA/WPA2 security options in web interface

I just got a WVC54GCA and found out that there are some missing configuration options in the wireless settings:
On the cameras web interface:
web interface > Basic : Wireless Settings > [ Edit Security Settings ] > Security Mode:
the dropdown gives me only two options: Disable and WEP, but no WPA, WPA2!
I upgraded to the latest firmware (1.1.00 build 02), but the problem remains.
Tried different browsers (Firefox 3.5, IE8) with the same result.
Is this a firmware bug? A faulty device? Anyone else having the same issue?
Solved!
Go to Solution.

Try to clear the Browser settings of your IE and then try to login to the setup page of your Camera, and check if you are able to find that options.... If still unable to find WPA/WPA2 Option on your camera, Press and hold the reset button for 60 seconds...Release the reset button...Unplug the power cable from your camera, wait for 60 seconds and re-connect the power cable....
Now check if you are able to find that options... If still not then i think it might be the problem with the Camera... I think you need to replace your Camera.

You cannot sign in to the Cisco Unified MeetingPlace Web Server interface using preconfigured system profiles

Hi
I recently upgrade tp 7.0.3 from 7.0.2.
While upgrade i found that i am not able to login to the web server with the admin id "admin" default created in the application server.
The same id i can login to application server , but not in wewb server.
I am getting the mentioned error "You cannot sign in to the Cisco Unified MeetingPlace Web Server interface using preconfigured system profiles".
However if i create a new user in application server and tried logging with the same in the web server it is working fine..
is it a known behaviour wirh the upgrade or i m facing some issue.
Hope i can find a solution here.
Regards
RC

RC,
This behavior is stemming from a change in MP 7.0 MR2 to disable the MPWeb login for system profiles. This was an internal change made by the developers to restrict the log on to the MPWeb page by the default accounts created in MeetingPlace upon installation. The change now displays this error when the admin account is attempted to be used for MPWeb login, as you experienced-
Error:[22953] You cannot sign in to the Cisco Unified MeetingPlace Web Server interface using preconfigured system profiles.
You should be able to log into MPWeb using any other user profile that you have either created manually or pulled in from LDAP/Active Directory. You just cannot use the admin account. This is reserved for login to the MP Application Server Administration page only. I am going to work to get this information added to the MP 7.0 documentation with a note for changed behavior in MR2 and above. Here is the note from MP 8.0 documentation-
Note: You cannot use this preconfigured admin profile to access the Cisco Unified MeetingPlace Web Server interface. Instead enter the User ID and password information from one of the other user profiles that have system administrator privileges to sign in to the Web Server.
Please let me know if you have any further questions.
Thank You,
Gerry

Security when using EM web interface to administer the database

When I'm connecting to the database
via EM Database Control web interface,
it uses http protocol (http://machine:5500/em),
can it be used for safety https protocol,
or are there when using standard http protocol
at least passwords encrypted before
sending it over http?

I have called
'emctl secure dbconsole' command,
it run successfully,
but when I tried to start it
'emctl start dbconsole', it failed,
now I'm not able to stop it,
when I do so, the output is like this
'--- Failed to shutdown DBConsole Gracefully ---',
the state is 'not running', but when I try to
start it now it complains that EM Database Control
is already running.
What to do to make it work now at least without SSL?

Cisco Prime 2.0 web interface access

We just installed Cisco Prime Infrastructure 2.0 Express. It seemed to have installed correctly? But Two oddities. First when the system is restarted it takes and inordinate amount of time before the web interface becomes available. Once the web service is responding, it will not except ANY login credentials.
I can ssh to the instance and using cli, added two additional accounts. All accounts can access the install instance using ssh. None are able to login to the webinterface.
Thoughts as to what I may have missed?
Gabe

Please login to the CLI as admin then execute the command to change the password for the root WebUI acccount
     > ncs password root password Private123
     Loading USER - root
     Validating new password..
     Resetting password ..
     Resetting password COMPLETED.
     EXECUTION STATUS : Success
Once you've changed this password please then try to use those credentials to login to
the WebUI you indicated was presented in your response above.
Let me know if this does it. If not, we'll need to go a little deeper:::

Cisco 4402 WLC IOS Upgradation using CLI and Web Interface

Hi,
I would like to know how to upgrade IOS of Cisco 4402 WireLess LAN Controller using CLI and Web interface ?
Can any one help me regarding the same.
Please answer as soon as possible.
Thanks in advance.

Here are the instructions for upgrading the controllers via GUI:
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn52.html#wp472449
Instructions via cli:
Cisco recommends that a direct CLI console port connection is used to update the controller software.
1. Make sure a TFTP server is available for the Operating System (OS) software download. Also, keep these guidelines in mind when the TFTP server is set up:
If a download is performed through the service port, the TFTP server must be on the same subnet as the service port because the service port is not routable.
If a download is performed through the Distribution System (DS) network port, the TFTP server can be on the same or a different subnet because the DS port is routable.
The TFTP server cannot run on the same computer as the Cisco Wireless Control System (WCS) because WCS and the TFTP server use the same communication port.
2. Download the desired OS software update file from the Cisco website to the default directory on the TFTP server.
3. Log into the WLC CLI.
4. Issue the ping server-ip-address command to verify that the WLC can contact the TFTP server.
5. Issue the transfer download start command and answer n when prompted to view the current download settings.
This example shows the command output:
transfer download start
Mode........................................... TFTP
Data Type...................................... Code
TFTP Server IP.................................
xxx.xxx.xxx.xxx
6. TFTP Path...................................... TFTP Filename.................................. AS_2000_3_0_x_x.aes --OR-- AS_4100_3_0_x_x.aes --OR-- AS_4400_3_0_x_x.aes Are you sure you want to start? (y/n) n Transfer Canceled Issue these commands to change the download settings:
* transfer download mode tftp
* transfer download datatype code
* transfer download serverip tftp-server-ip-address
* transfer download filename filename
* transfer download path absolute-tftp-server-path-to-file
Note: All TFTP servers require the full pathname. For example, in Windows, the path is C:\TFTP-Root. (In UNIX forward slashes (/) are required.)
7. Issue the transfer download start command to view the updated settings, and answer y when prompted to confirm the current download settings and start the OS code download.
This example shows the download command output:
transfer download start
Mode........................................... TFTP
Data Type...................................... Code
TFTP Server IP.................................
xxx.xxx.xxx.xxx
TFTP Path......................................
path>
TFTP Filename..................................
AS_2000_3_0_x_x.aes --OR--
AS_4100_3_0_x_x.aes --OR--
AS_4400_3_0_x_x.aes
Are you sure you want to start? (y/n) y
TFTP Code transfer starting.
TFTP receive complete... extracting components.
Writing new bootloader to flash.
Making backup copy of RTOS.
Writing new RTOS to flash.
Making backup copy of Code.
Writing new Code to flash.
TFTP File transfer operation completed successfully. Please
restart the switch (reset system) for update to complete.
8. The WLC now has the code update in active volatile RAM, but the reset system command must be issued to save the code update to non-volatile RAM (NVRAM) and reboot the WLC.
This is a sample output:
The system has unsaved changes.
Would you like to save them now? (y/n) y
The controller completes the bootup proce

Can only telnet from other switches to a SG300 switch. Also can't access web interface.

For whatever reason I can telnet from another switch to the SG300 switch but not directly to the switch. I also can't access the web interface or ping the switch. Any help would be appreciated. Here is the running config
config-file-header
WasteWaterSG30010MPP
v1.3.5.58 / R750_NIK_1_35_647_358
CLI v1.0
set system mode switch
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end xxxxxxxxxxxxxxxxxxxxxxxx
vlan database
default-vlan vlan 2
exit
vlan database
vlan 2,75,200,999
exit
voice vlan id 200
voice vlan oui-table add ________
voice vlan oui-table add _phone_____________
voice vlan oui-table add ___________________
voice vlan oui-table add ______________
voice vlan oui-table add
voice vlan oui-table add ___________
voice vlan oui-table add ___
voice vlan oui-table add ______________
hostname WasteWaterSG30010MPP
line console
exec-timeout 0
exit
line telnet
password 382fda4a4a26e6637edac0eb8b8ba4581087d32d encrypted
exit
line console
password 382fda4a4a26e6637edac0eb8b8ba4581087d32d encrypted
exit
enable password level 15 encrypted 382fda4a4a26e6637edac0eb8b8ba4581087d32d
username admin password encrypted 382fda4a4a26e6637edac0eb8b8ba4581087d32d privi
lege 15
snmp-server location XXXXXXXX
snmp-server community String1 ro view Default
sntp server 172.16.2.1
ip telnet server
interface vlan 2
ip address 172.16.2.23 255.255.255.0
no ip address dhcp
interface gigabitethernet1
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport mode access
switchport access vlan 999
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type unknown
interface gigabitethernet2
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet3
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet4
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport mode access
switchport access vlan 999
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type unknown
interface gigabitethernet5
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet6
spanning-tree portfast
switchport mode access
interface gigabitethernet7
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet8
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet9
spanning-tree link-type point-to-point
switchport trunk allowed vlan add 75,200,999
switchport trunk native vlan 2
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
interface gigabitethernet10
spanning-tree link-type point-to-point
switchport trunk allowed vlan add 75,200,999
switchport trunk native vlan 2
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
exit

A member of which VLAN ID is that device from which you trying to reach that switch?
Is that device directly connected to switch WasteWaterSG30010MPP? If yes, to which port?
If you are connecting from different VLAN than VLAN2, are you using routing between VLANs? Where is that routing device connected to?
> I also have another switch that connects to the network through this switch and am able to telnet to it.
that second switch member of same VLAN 2? Or management is part of different VLAN?
..too few information to be able to give you final answer.

SPA303 password only for web interface

Is there a way to ask for user password when connecting to web interface of the phone, but not to ask when accessing directory (and other phone features secured by user password) from the keypad?
I want to secure phone on the local network, meanwhile allowing user to access directory without any kind of password/code.

Hi Nilesh,
did you check whether reentrence tickets are enabled? Usually WD transactions can eb called form within the SAPGUI without the pronpt, if this is configured correctly,
For more info, please check the docs. You can also check this thread, where this has been already discussed.
Kind regards,
Patrick

Web interface no loading in Cisco Small Business 300 Series

Hi everyone!
I have a Cisco Small Business 300 Series Managed Switches as a floor switch. It is working fine (apparently), but I can no longer get into the web interface to manage it. The web page load till 70% and stops loading. Can someone suggest a solution please?
Thanks

Hello,
I was hoping to see error :-) Bu it looks like you have a console access with no issue. Can you test web access when PC is directly connected to switch? Do you observe the same issue?
Aleksandra

Cisco ISE Web interface Login

Hi,
Can anyone help me in resetting the Cisco ISE web interface password. I'm able to login to CLI of ISE but couldnt use the same credentials to login to web interface. Is there any way to reset this web interface password through ISE CLI?
Thanks
Daniel

Daniel,
Just ran across your question, the answer is you can have login credentials for the cli but that is seperate from the gui. The way I understand it is once you get to the gui for the first time user is admin and password is cisco. At this point you are required to put in a new password. Once in the gui other users can be created for the gui.
Erik

Cisco SPA514g Secure web interface only.

Similar Messages

Maybe you are looking for