Cisco SX80 - Using Sony SRG-300HW cameras

Hello,
I have a client that's ordered a Cisco SX80 with a Precision 60 Cam and they wish to add two Sony SRG-300HW cameras to the system for a total of three cameras. The reason for the different cameras is they have to be ceiling mounted and able to point directly down to a operating table.
My question is - can the SX80 control via serial / visca the three cameras?
From what I have seen the stock camera that comes with the Cisco SX80 does not have a serial pass through and there's little information available to confirm this. In turn why I am asking about this here to see if anyone has had any experience with alternative cameras with the Cisco SX80 and various configuration ideas.
Any advice would be greatly appreciated.
Kind Regards,
Craig

Hi!
>>>See the SX80 Physical Interface Guide.
Thank you. SX80 has serial connection and 4x camera will work but it is not clear if it supports daisy chaining or not. There is nothing about VISCA daisy chaining. So it is unclear if one can connect 3 cams in such config:
codec -> PHD 4x -> PHD 12X ->PHD 12x.
I hope someone from Cisco helps?

Similar Messages

Is there a way to use the Tablet Remote to control a Sony Alpha DSLR Camera?

I own a Sony Tablet and love the ability to use it as a Remote Control. I also own a Sony Alpha DSLR...yet I can't get the remote control to control the Camera. Has anyone figured out how to do this yet? It's a little large, but would be amazing if the camera had DLNA and could automatically publish a photo on the tablet right after I took the pick...with the Tablet remote!!!
Thanks for any advice.

Hello Damon,
What is the exact model # of Sony Alpha DSLR Camera?
You can try “Learning from remote” feature if your DSLR camera is remote control capable.
Refer the following link for instructions:
http://www.kb.sony.com/selfservice/documentLink.do?externalId=C1023514
Camera should be DLNA server capable in order to access pictures from it using DLNA application in the tablet.
If my post answers your question, please mark it as an "Accepted Solution."

We recently updated to Lion, prior to this update we could plug in our Sony Mini DV camera using the appropriate firewire and the iMovie would recognize the camera. This function no longer works after the update to Lion. Any suggestions?

We recently updated to Lion, prior to this update we could plug in our Sony Mini DV camera using the appropriate firewire and the iMovie would recognize the camera. This function no longer works after the update to Lion. Any suggestions?

Zap the PRAM and Reset the SMC, then try again.

Is it possible to use a Linksys By Cisco Wireless-G Internet Home Monitoring Camera with Labview

I was wondering if it is possible to use a 'Linksys By Cisco Wireless-G Internet Home Monitoring Camera' with Labview
http://www.dabs.com/productview.aspx?Quicklinx=53PX&SearchType=1&SearchTerms=network+cameras&PageMod...
I wan't to be able to get the raw data from the camera and analyse it.
Message Edited by Jam.hall on 03-25-2009 09:03 AM
Solved!
Go to Solution.

Hi Jam.Hall
I am somewhat hesitant to say you will be able to use this camera with LabVIEW. It all depends on what functionality you are wanting to utilise on the camera, and how much video you want to analyze.
- If you want to use the wireless functionality, I am concered that the on board web server will compress and embed the video stream. I do not beleive this is something we can access in LabVIEW.
- If you wish to use the ethernet connection, if it is Gigabit Ethernet, then you should be able to use our IMAQ for GigE driver to bring in the feed, but looking at the specs for the camera, I'm not sure that this is an option.
- My other suggestion might be to utilise the record video stream function that the camera has. Depending on the format of the video file, you may be able to read in the recorded file and analyse it in LabVIEW.
If you could explain the purpose of your application, and what you would like to achieve with the system, there may be more suitable products that you can use.
Kind regards,
Sheela Sujeeun
Applications Engineer
National Instruments UK

I can't open RAW files from new Sony Alpha a6000 camera in PSE 11 camera raw editor. Is there an update that will allow me to do this or do I need to always use DNG convertor?

I can't open RAW files from new Sony Alpha a6000 camera in PSE 11 camera raw editor. Is there an update that will allow me to do this or do I need to always use DNG convertor?

You would need to update to PSE 12, or just keep using the DNG converter. Your camera requires ACR 8.4, which isn't compatible with PSE 11. It's also not compatible with PSE 12 if you are running Vista or XP.

Can you live stream video to computer using Sony Action Cam X1000V 4K?

I'm a computer programmer and I need high quality camera and Sony Action Cam X1000V suits me the best. I would like to know can I stream live video to my computer using hdmi/usb/wifi/anything from Sony Action Cam X1000V?

Hi PatrikWWDC,
Welcome to the Sony Community!
Yes, you can do live streaming using the FDRX1000V action cam. You can use UStream to stream your videos live online. Here is a guide on how to prepare the camera for Live Streaming.
For further assistance with your concern, we recommend visiting our Sony Global Web site for information on contacting the Sony Support Center in your region at http://www.sony.net/SonyInfo/Support/.
If my post answers your question, please mark it as "Accept as Solution". Thanks_Mitch

No video when trying to capture PAL dv tape w/Sony HVR-V1U camera

Hello there,
Im attempting to Log & Capture a DV tape with "DV SP PAL" content from a Sony HVR-V1U camera using an iLink FireWire.
I have deck control, timecode, and audio but no video. Instead I see bars for video w/the ominous "preview disabled" band. When I attempt "Capture Now," I receive the follwoing message "this operation could not be completed as there is no video." For Easy Setup, Im currently in "Format: PAL; Use: DV-PAL FireWire Basic" (ive other combinations, and again best I can get is deck control but no video).
The DV PAL tape plays fine in the camera's LCD screen. Also I had no issue capturing HDV NTSC tapes using the same Sony HVR-V1U camera.
I've checked my settings and the usual obvious stuff but no luck.
If anyone has any ideas on what Im doing wrong or things I could try it would be much appreciated.
Many Thanks,
Sam

are you sure this camera is fully pal compatible? Some cameras/decks will play back certain formats but will not output via firewire. Can you shoot PAL with this camera? If not, I'd guess you can't use it to capture PAL via firewire. Might check the camera manual.

How do I connect my Sony HD video camera to work as my webcam on a mac-mini

I have just purchased a 2.5GHz 4Mb mini-mac. I am using a Samsung HD TV and want to use a Sony HD video camera as a webcam. I have mini-display port, HDMI port and thunderbolt port on the mini-mac. The video camera has mini HDMI port and I have mini HDMI to HDMI cable. I also have HDMI to mini-disply connector. So far I have tried connecting the TV via the HDMI to HDMI cable and the camera via mini HDMI to HDMI/HDMI mini-display convertor to the mini-mac. The TV is showing the display but the video camera (turned on!) doesn't automatically appear or show in either Finder or as available when I am trying to set up Skype. Then tried swapping the two around at the mini-mac with the TV now going through the HDMI to mini-display convertor and the camera going to the HDMI port. Same results as previous set-up.
Can this be made to work? Is there a HDMI to thunderbolt convertor that will work? Is this plug and play technology or are there more complicated set-up [rocedures? Any help much appreciated.

Solved with new cable: http://www.ebay.com/itm/330709481045?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m149 7.l2649

Yours sincerely! I just bought a Sony DCR-SD1000 camera only when installing the cd drivers not supported by the operating system Machintosh. I've contacted the seller said the store did not provide for the apple os. How can I move all the files on the ca

Yours sincerely! I just bought a Sony DCR-SD1000 camera only when installing the cd drivers not supported by the operating system Machintosh. I've contacted the seller said the store did not provide for the apple os. How can I move all the files on the camera the port out is to use a USB data cable to a laptop for my macbookpro can not read the contents of the file and the camera. I also want to use the lens on the camera as a substitute for the embedded camera on my macbookpro, what should I do to replace the embedded camera on macbookpro with sony camera so that the camera could be more variety and can I record when I turned macbookpro . Please help for this so that I can quickly capture the results from sony camera to my macbookpro. Thank you.

See this page http://macosx.com/forums/networking-compatibility/296947-sony-camcorder-my-mac.h tml - might be some helpful tips there.
Clinton

Print to video - HDV 1080i60 to Sony HDR-HC1 camera

Like many before, am struggling with print to video of HDV material captured as HDV 1080i60 to a Sony HDR-HC1 camera. Just can't figure out what settings to use, only get the darn blue screen. Have tried several settings, but no success. Does anyone know the trick? Thanks!

Tim Kuhlman-
Have you tested the camera with non-HDV just to make sure the camera works?
Luck-
-DaddyPaycheck

How do I import video from a Sony DSC-HX100V Camera into iPhoto

How do I import video from a Sony DSC-HX100V Camera into iPhoto? . . . i can see all the photos but the videos are not visable (I also connected the SD card with a USB Sony SD Card Reader - again only the photos are accessible - no video files are shown) . . .

If you're shooting AVCHD then you'll need to upgrade to iPhoto 11v9.3 to import this material.
A note on AVCHD: This format was developed for people who are shooting to edit the material afterwards. If you're shooting to edit, then iMovie or Final Cut are the correct home for this material. If you're not shooting to edit consider using one of the other video formats on your Camera.

SONY Digital Video Camera DCR-DVD 201 and iMovie

I have a sony Digital Video Camera
Posted: Aug 6, 2006 6:59 PM in response to: max Farina
Reply Email
Can I use this Digital camera with my MacBook Pro
it is a SONY DCR-DVD 201
I do not see a firewire port on the camera ONLY a USB.
How can I get my video from my DVD to iMovie?
I want to put my home video from this camera to iMovie, Can it be done?
I am going nuts, I paid alot of money for this camera and now I can't use it in my new Mac?
I am very new to Mac and this hurts!
PLEASE someone help me, I only see a USB, DO they sell some thing to help get the Video into iMOVIE?
Thanks......

Search this forum for "compatible, DVD camcorder" and you will find many threads where people lament this truth:
iMovie is for miniDV formatted video connected via Firewire.
Mini DVD camcorders are designed for you to do very light editing on the camera before you finalize the DVD and don't support being imported into a computer. Anyway, many of the experts here know of converters and workarounds, if you want to spend some more money. You could start with these threads:
http://discussions.apple.com/thread.jspa?messageID=2404104&#2404104
http://discussions.apple.com/thread.jspa?messageID=2288697&#2288697
http://discussions.apple.com/thread.jspa?messageID=2243781&#2243781
Somewhere I have read a pretty detailed thread describing what converter you need and how to do it. So just keep searching...

Using Sony's IDC in combination with Lightroom

I would like to use Sony's IDC Raw converter that comes with the Sony A700 camera, to be able to process through Sony IDC the RAWs with DRO's (Dynamic Range Optimalization) applied (as shot with the A700).
However I would like to keep LightRoom as my archiving base.
Question:
Can I bring RAWs after importing in LightRoom, to IDC?
Can I after converting the RAWs in IDC, bring the resulting PSDs (or JPEGs) from IDC back to Lightroom (for archiving)?
I appreciate your help!

Yes, and No!
Lightroom won't allow you to use IDC on the Raw file, Lightroom only allows ACRaw to be used to "develop" a raw file. However, you can use Lightroom's ranking and review functions to help you decide which files you want to work with. Then right click and select show in explorer. Then select the file you want to develop, and tell Explorer to open in IDC. You then can develop, save as a Tiff and import.
Pain in the Arse isn't it?
Frankly if you have access to Bridge then this is faster and more convenient. Import the ARW and use IDC to make Tiffs.
But why do you want to do this?
Frankly DRO only becomes special when you use DRO Advanced. Anything else can be easily duplicated in Lightroom. DRO Advanced can not be done by IDC,(it's like Lightzone on Steroids) it's done by the camera, the processor looks at each pixel and compares it with adjacent pixels and makes adjustments in the jpg. So the only way to utilise DRO Advanced (and it's astonishing what is achieved) is to shoot in Jpg (and probably in cRaw + Jpeg) I shoot everything in cRaw only but have a MR setting to utilise DRO Advanced - cRaw + Jpeg, ISO 200 (remember that DRO advanced effectively locally amplifies the pixels, so if you start at say ISO 800 certain pixels could be amplified to ISO 6400!
I can then import both the cRaw and the Jpeg.
Hope this makes sense.
Peter

When downloading from a Sony minidisc video camera, the picture is downloading but without sound. Previously, it had downloaded successfully both sound and picture. I have subsequently upgraded to Lion X (10.7.4). Is there some problem with the driver?

When downloading from a Sony minidisc video camera, the picture is downloading but without sound. Previously, it had downloaded successfully both sound and picture. I have subsequently upgraded to Lion X (10.7.4). Is there some problem with the upgrade which is affecting the transfer? Is there a way of resolving this?

When you have kernel panics, the pertinent information is in the panic report.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
In the Console window, select
DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar.
There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A panic report has a name that begins with "Kernel" and ends in ".panic". Select the most recent one. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
If you don't see any reports listed, but you know there was a panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report.
I know the report is long, maybe several hundred lines. Please post all of it anyway.

Does apple have update to idvd so I can use Sony dcr-sx44 camcorder

Does apple have an update to idvd so I can use sony dcr-sx44 camcorder?

If you already have iDVD then run Software Update, if there are any updates available for iDVD they will be posted. While that doesn't answer your question directly it is your best option. Looking at the software specifications for the camera it doesn't look like it was ever intended to work with OS X. This is what I found on Sony's website:
Software
Supplied Software : PMB Ver.5.0 Supports Windows XP Service Pack3 (SP3)(32bit), Windows Vista Service Pack2 (SP2) (32bit), Windows 7, 64-bit editions and Starter (Edition) are not supported. Not supported by Mac OS.
Operating System Compatibility : "Windows XP SP3 * /Windows Vista SP2 ** /Windows7 * 64-bit editions and Starter (Edition) are not supported.The Windows Image Mastering API(IMAPI)Ver.2.0 or later is required to use the function for creating discs. ** Starter (Edition) are not supported. Standard installation is required. Operation is not assured if the above OS has been upgraded or in a multi-boot environment. "
I suspect a camera upgrade may be what you need to do.

Cisco SX80 - Using Sony SRG-300HW cameras

Similar Messages

Maybe you are looking for