Cisco TS 320 integration with CUCM

Dear Expert,
Is there any way we can integrate the TS 320 with CUCM without any conductor.
Means by SIP trunk or as Conference bridge.
BR

I have TS on Media 320, so its means we can not use it as locally managed.
The TelePresence Server on Media 310/320 and Cisco TelePresence Server on Virtual Machine do not support locally managed mode; on these platforms, the
TelePresence Server must be managed by a system like Cisco TelePresence Conductor or Cisco TelePresence Exchange System.
BR

Similar Messages

  • Jabber cannot Call - Integration with CUCM/AD

    Dear all,
    I installed CUCM 9.1.1 and CUPS 9.1.1 with Jabber client 9.0.1.
    when I run Jabber on a joined domain PC (login with AD username and password), there are no problem with the calling ability.
    But when I try to use a non-join domain PC (I am using VPN to connect to office network and using my personal PC), only the chatting feature that are available. I cannot loggin to phone accounts and cannot make any calls with my Jabber client.
    Should I use UDS integration with AD?
    Thanks,
    Hasan

    Hi Hasan,
    Can you take a look on this thread:
    https://supportforums.cisco.com/message/3914353#3914353
    If you still have problem connecting, can you try with newer version of Jabber?
    Regards,
    Srdjan

  • Can't establish a Voice gateway (cisco 2911) using SIP with CUCM 9.1

    I have configured a Cisco 2911 as a Voice Gateway using SIP (the configuration is attached), but unfortunately can't establish a test call to a phone (CUPC 8.6 SCCP) using csim start. I have done logging the ccsip debug and ccapi debug and attached them. Could anyone help me to solve this problem?

    I just did some research on my end and csim is not supported for SIP. The Invite will never be created and sent to the CUCM to initate the call. It disconnects in the router itself with normal cause.
    *Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Error/sipSPIOutgoingCallSDP: 
     Could not create source SDP for Outgoing Call
    *Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Error/sipSPICreateOutboundSDP: 
     Error in creating an SDP for the outbound call - Check for supported codecs
    *Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Error/preprocessSetup: 
     Error during outbound SDP creation
    *Apr 18 08:58:48.086: //40/7D08458F8077/SIP/Info/sipSPIInitiateDisconnect: Initiate call disconnect(16) for outgoing call
    Please use an actual call to test your dial-peer and integration with call manager. csim will not work.
    Hantale
    Sree

  • Cisco WAAS moibile integrated with Symantec Backup Exec 2010

    Here customer requirement is to take backup of opened Database file .fdb
    (Microsoft Dynamic Navision) integrated with WAN optimization (Cisco WAAS
    mobile).
    Problem is  Cisco WAAS mobile is not optimizing  Symantec backup process when backup job is running.
    Please find attached files (WAAS mobile accleration status with symantec
    backup process).
    Customer is using Microsoft Dynamics Navision (ERP application).
    WAAS mobile client is connecting and file copy is accelerating, but
    symatec backup (beremote.exe) and Navision (fin.exe) processes are not
    accelerating.
    I added above processes in WAAS mobile server's acceleration list.
    Please advise if any changes has to made in WAAS mobile server.
    Regards
    Prasad
    Cell: 9000012355

    Hi Prasad,
    According to the screen shots provided the fin.exe process is bypassed due to Low Latency.  From the admin guide this means:
    Bypassed : Low Latency. The latency between the client and the application server is less than the latency threshold, which is 10 ms by default. This threshold may be modified on the Connection Settings tab on the Configure > Clients > Networking page.
    Also, I see SERVER.exe process is going to the same server or subnet as fin.exe but is bypassed due to Pre-Existing connection.
    Bypassed: Pre-existing Connection. When WAAS Mobile is started after other applications, the existing TCP connections associated with those applications will not be reset unless the “Auto Reset Connection” property has been selected for the process in the Accelerated Processes table, and hence, these pre-existing connections will be bypassed.
    Lastly, I see bermote.exe is listed as Bypass Reason Unknown in one of the screen shots.
    Bypassed : Reason Unknown. This message will occur when an attempt to reset a TCP connection associated with an application that has been configured to have these connections be automatically reset (via the Accelerated Processes table on the Configure > Clients > Acceleration page) fails.
    Is this client actually accessing a server that is remote for these first two processes?
    For the last process, did we try to first exit the application in question and all the associated processes (beremote, and any other processes that may get started with this application), then start the WAAS Mobile client, then finally start the associated process/application?
    Cheers,
    Mike Korenbaum
    P.S.  If this answers your question please mark it as such.

  • Cisco UCCX 8 - Integration with SAP BCM

    Hi
    Can Cisco UCCX 8 be integrated with SAP BCM for the crm requirements?
    Thanks,

    I have heard that these guys offer an integration but have not worked with them myself:  http://www.tcandc.com/cisconn

  • Jabber for Windows - without LDAP integrated with CUCM Jabber UDS - NO PEOPLE CAN SEARCH

    Hi all Jabber Experts,
    I have the CUCM, which is the versin 8.6 and the Presence Server, which is the version 8.6, that is not integrated the LDAP, but I want to deploy the Jabber for Windows.
    So I would use the UDS to deploy the Jabber for Windows (modified the XML and uploaded to the CUCM TFTP server).
    Finally, that can login the users, which is manually added from CUCM.
    But I cannot search other users from the Bubby List. Any idea for that?

    First of all, either you use CUCM 8.6 with CUPS 8.6, or you use CUCM 9.1 with IM&P 9.1, what you're mentioning is just impossible as they're not compatible and that's not supported.
    HTH
    java
    if this helps, please rate
    www.cisco.com/go/pdihelpdesk

  • Need Urgent Help on Meeting Place Integration with CUCM 7.1 and AS5400 PSTN Gateway

    Hi,
    This is first time I am on this forum.
    I have already tried going through a lot of docs on docwiki.cisco.com but couldn't find complete configuration help.
    I have to integrate Meeting Place 8.X with an existing CUCM and an E1 gateway (PSTN Gateway) AS5400.
    The CUCM is already part of a Telepresence Environment. I need to create a SIP trunk between AS5400 and CUCM 7.1 and then create a Trunk between AS5400 and Cisco Unified MP 8.X and then between CUMP and CUCM.
    I need help on AS5400 SIP Configs as well as parameters I need to cover on CUCM (Though I have done some basic dial-peer configs but they haven't been of much help).
    Then I also need help on AS5400 SIP configs with CUMP 8.0
    Any docs on Integration between CUMP and TP3000 will be of great help too.
    Rgds,
    Asim

    I can get the Ricoh to register as sip endpoint, it answeres then imediatly disconnects. Doing a monitor with Wireshark looks like it attempts to negotiate t38 but fails. Any idea why this fails?
    |160.260684000|         INVITE SDP (g711U)            |                   |SIP From:
    |         |(5060)   ------------------>  (5060)   |                   |
    |160.338806000|         INVITE SDP (t38)              |                   |SIP Request
    |         |(5060)   <------------------  (63435)  |                   |
    |160.339545000|         491 Request Pending           |                   |SIP Status
    |         |(5060)   ------------------>  (5060)   |                   |
    |160.547894000|         406 Not Acceptable            |                   |SIP Status
    |         |(5060)   <------------------  (63435)  |                   |

  • LDAP Integration with CUCM 9.0

    We would like to use LDAP to sync all of our users from Active Directory.  All of our current CM Users are local, the problem is that they have the same user names as our Active Directory users.  From what I understand this is going to be a problem because:
    "If accounts from LDAP match an existing Unified CM account that is not marked as an LDAP synchronized account, then these accounts are ignored."
    Does that mean we will have to delete all our existing CM users in order to sync the LDAP users correctly?  Is there a best practice for this?  Once we syncronize the LDAP users how to I ensure that the user gets associated with the proper phone?  Or do I have to visit each user individually? 

    I just did a quick test for this, my lab CUCM 9 is already LDAP integrated, but I created a local user, then I created that same local user in my LDAP OU, and performed a full sync.
    The user is no longer showing as a local active user, but as an active LDAP synchronized user.
    Which was my thought, there's only one conversion, from LDAP to local.
    The behavior is just as with any previous release, local users who match an LDAP user after you enable it, are just updated, and kept with all their configurations.
    I checked the option to turn it back again into a local user, did a full sync, and it's again an active LDAP user.
    HTH
    java
    if this helps, please rate
    www.cisco.com/go/pdihelpdesk

  • Contact Center Ent. Integration with CUCM

    I have CUCM 8.0 and CCX 8.0 and i am trying to setup the integration between them.
    I have created a user on the CUCM and CTI Port and done the required configuration on the CCX.
    Under CTI Port Status & IP Address it is giving unknown.
    I have attached the configuration on CUCM and CCX.
    Any help will be highly appreciated.

    this is wrong , they have to be created on the UCCX , the UCCX will automaticly creat them on the CUCM.
    check the link below :
    http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_8_0/configuration/guide/uccx801ag.pdf
    Amer

  • Cisco call manager integration with mediant

    How can we add and integrate mediant with cisco call manager ?
    Can you have doc for this kind of setup ?

    Hi Sachin,
    We do run a hybrid Callmanager to Nortel Meridian setup (works well).
    Here are some great docs;
    Cisco Unified CallManager
    Case Study: Nortel 61C PBX to Cisco IP Telephony Migration
    From this good doc;
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_white_paper09186a00801115e0.shtml
    Nortel Meridian PBX and Cisco CallManager Integration
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a008011888c.shtml
    Cisco Unified CallManager System Guide, Release 4.2(1)
    Cisco DPA Integration
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a008055cd53.html
    Hope this helps! Let me know if you need additional info.
    Rob

  • Cisco Unified Communications integration with Exchange cloud service

    Has anyone integrated Presence and/or Unity Connection with an Cloud based Exchange provider service? Presence would be for calendar integration and Unity Connection would be for Unified Messaging (Single inbox for vmail and email)?
    Thanks,
    Mark

    Yes, BPOS is supported in CUC 8.5
    http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/design/guide/8xcucdg010.html

  • Cisco Prime NCS integration with ACS 5.1

    Hello,
    We've an issue with authorization on NCS system. NCS successfully integrated witch ACS, but there is a problem with one user. All users have equivalent rights under root. There is shell profile with all possible tasks (exported from NCS server) configured on ACS. All users exept this one (unlucky one:)) authorizes successfully.  In  ACS logs, authentification and authorization status for this user is passed and all attributes (policy, profile, AV-pairs e.t.c.) is the same as for another users. This 'unlucky' user gets a following message:
    There is surely no browser or network issue. Tried from different PCs with same result. There is no any local info related to this username on the NCS server. When i change one charecter in the username on his ACS account, everything works well. What could be a possible reason of this behaivour?  Thanks!
    Our ACS v
    Version 5.1.0.44.X
    And NCS
    Version : 1.1.2.X

    this question should be moved to the Security > AAA forums as this sounds more like an ACS issue than NCS.
    HTH,
    Steve
    Please remember to rate useful posts, and mark questions as answered

  • Cisco Security Manager integration with ACS

    Has anybody got this working yet.
    I have tried but as yet have been unsucessful in registering csm with the ACS server.
    I am following the the instructions however, nothing seems to work all i get is failed to registar.
    Any help would be appreciated
    Regards
    Jason

    Check out this link...
    http://www.cisco.com/en/US/products/ps6498/prod_troubleshooting_guide_chapter09186a00806e23e3.html

  • Cisco Security Manager - Integration with LMS/DCR

    Following on from my posts in:
    http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Network%20Infrastructure&topic=Network%20Management&topicID=.ee71a02&fromOutline=&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc16e9f
    How do I configure CSM so that I get the option to "Add Device from DCR" rather than having to export/import the devices manually?
    Many thanks

    Any ideas?

  • Cisco WCS/NCS integration with airmagnet

    Hi,
    I used Airmagnet to preform a site survey and i want to import the maps into the WCS/NCS how can i do that?
    Thanks,
    Omer Shtivi

    Hi,
    Thank you for your replay.
    As far as i know there is a way to export the plan from the Airmagnet and into the WCS/NCS.
    there is an option in the Airmagnet Cisco Prime NCS/WCS export.
    when i export the file it save it as a zip file, when i open it there is three folders inside, csvfiles images and xmlDir, when i import the the XML file i get the error:
    XML Import: 'AMPlanner.xml' has an unsupported Mime Type\n\nMime Type sent by  Browser 'text/xml'\n\nPossible causes/workarounds\n1. Check File  [Associations/Types/Extensions]\n2. Ensure appropriate application launches  file\n3. Try a different browser\n4. If File [Associations/Types/Extensions] are  correct try closing the browser and relaunch\n\nMaps Import: Supported file  format mime types are \n\n'application/gzip-compressed',  'multipart/gzip-compressed', 'multipart/x-zip-compressed',  'application/x-gzip-compressed', 'application/zip', 'multipart/zip',  'application/x-zip-compressed', 'multipart/x-gzip', 'application/x-zip',  'application/gzip', 'application/x-gzip', 'multipart/x-gzip-compressed',  'multipart/gzip', 'multipart/x-zip'\n\n

Maybe you are looking for

  • What the difference and use between   of  TABLES and SY-REPID?

    Hi, Experts, I have came accross 2 cases that i can't able understand EX1: TABLES: VBAP   - >( Here also Appplication Server(AS) creates Wrokarea of Structure VBAP but, by  data: v_vbeln like vbap-vbeln.    double clicking on variable v_vbeln AS taki

  • Process order settlement Ko88 not working.

    Hello Sapients, i am getting a message:"There are no accrued amounts; settlement is not possible." Following are the steps i cariried. 1.) created a Process order CR01 2.) did goods issue to the process order using MIGO_GI 3.) when i run KKAX I am ab

  • Why does "enclosing folder" not work from the SEARCH window?

    I do a command+F search. Command+2 to view as list rather than groups and then sort by date modified. When I find the file/folder I want I'd really like to do a command+[up arrow] which in the GO menu is a valid command. Why does this work in finder

  • HT4061 My iPhone keep showing the iTunes logo

    I made the latest update. I was chilin on instagram. The camera begin to do weirdo stuff and then the iPhone simply shot down. Now, each time I wanna boot it up it shows this images: I try to connect it on iTunes obviously. iTunes tell that my iPhone

  • No icons on menu bar

    I previously had spotlight, time, language, ect. icons on the menu bar but now there is only the gmail icon. I tried clicking on the options of adding icons on menu bars, but it doesn't work. For example, i click "show time and date" and when i switc