Cisco UC Integration for Microsoft Lync Release 8.6.2 Question
Hello Team,
Could you please advise if CUCI-Lync integration 8.6.2 supports CUCM 9.1(2) and CUC 9.1.(2)? I checked the release notes for this version, and it does support CUCM 9.0, but CUC 9.X is not referenced on the document.
As a side note, the reason I have to go with 8.6 is the customer's current Communications Server is OCS 2007 R2. I checked the notes for CUCI-Lync 9.2(1) and up, and OCS 2007 R2 is not listed as a supported platform.
Thank you,
Gerson
This is how CUCI-Lync 9.X works, separate application, no longer attached to the Lync client. As bad as it sounds this is how Cisco made it work after simply replacing previous CUCI-Lync with stripped version of Jabber in version 9. Sorry.
HTH,
Chris
Similar Messages
-
After I uninstall Cisco UC Integration(TM) for Microsoft Lync 8.6 from my computer and reinstall Cisco Jabber 9.2(3), I found my Jabber got the same interface of sign in with Cisco UC Integration(TM) for Microsoft Lync. it let me input the TFTP,CTI,CCMCIP server adress, instead of choosing the presence server and inputing the presence server address and domain.
after I sign in, it is aslo like Cisco UC Integration(TM) for Microsoft Lync, there is not the side button of contacts list, I can only search the person to call and can not send message or chat any more.
I tried many times to uninstall and reinstall Jabber,i failed, except I install Jabber 9.1(3), it works well. but I try to reinstall 9.2(3) again, it goes back like Cisco UC Integration(TM) for Microsoft Lync,why?
Thx.Hi,
You probably had CUCILync 9.2 installed previosly, and since CUCILync 9.2 is based on Jabber phone mode, the interfaces are the same. (You have Jabber phone mode nterface now)
These settings are written in jabber-boostrap.properties file and Jabber reads them from here.
That file is stored here:
C:\ProgramData\Cisco Systems\Cisco Jabber
If you delete thise file, interface should change.
If you want to install Jabber and avoid such things, do this with option clear=1
- msiexec.exe /i CiscoJabberSetup.msi CLEAR=1 ...
Regards,
Srdjan -
Language Pack For Microsoft Lync 2013
Hi,
Do you have any idea when will Language Pack for Microsoft Lync 2013 be released?
Thanks,Hi EAskaroglu,
Lync 2013 is part of Office 2013, you can install the language packs for Office 2013.
There is no language pack for Lync Server 2013, you can choose the language when download the installation package.
Best regards,
Eric
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected] -
Team,
Unable to start FE service on one of the FE server, 2 Enterprise lync 2013 pool one FE in each pool, only following error in event vrw,
Log Name: Lync Server
Source: LS Server
Date: 12/30/2013 12:10:55 PM
Event ID: 12290
Task Category: (1000)
Level: Error
Keywords: Classic
User: N/A
Computer: ACS465-BH102.me.ykgw.net
Description:
The evaluation period has expired.
The evaluation period for Microsoft Lync Server 2013 has expired. Please upgrade from the evaluation version to the fully licensed version of the product. Look at help for Setup.exe to learn how to upgrade from evaluation version to the licensed version.
Cause: The evaluation period for Microsoft Lync Server 2013 has expired.
Resolution:
Please upgrade from the evaluation version to the licensed version of the product. Look at help for Setup.exe to learn how to upgrade from evaluation version to the licensed version.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="LS Server" />
<EventID Qualifiers="50152">12290</EventID>
<Level>2</Level>
<Task>1000</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-12-30T09:10:55.000000000Z" />
<EventRecordID>73953</EventRecordID>
<Channel>Lync Server</Channel>
<Computer>ACS465-BH102.me.ykgw.net</Computer>
<Security />
</System>
<EventData>
</EventData>
</Event>
Log Name: System
Source: Schannel
Date: 12/30/2013 12:13:36 PM
Event ID: 36888
Task Category: None
Level: Error
Keywords:
User: SYSTEM
Computer: ACS465-BH102.me.ykgw.net
Description:
The following fatal alert was generated: 10. The internal error state is 1203.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Schannel" Guid="{1F678132-5938-4686-9FDC-C8FF68F15C85}" />
<EventID>36888</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x8000000000000000</Keywords>
<TimeCreated SystemTime="2013-12-30T09:13:36.779033200Z" />
<EventRecordID>83985</EventRecordID>
<Correlation />
<Execution ProcessID="556" ThreadID="3668" />
<Channel>System</Channel>
<Computer>ACS465-BH102.me.ykgw.net</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="AlertDesc">10</Data>
<Data Name="ErrorState">1203</Data>
</EventData>
</Event>
Server is already on Full version, ran Reset-CsPoolRegistrarState
for fillrest as wel as serviceret
Followed below as well,
http://social.technet.microsoft.com/Forums/lync/en-US/2a7e27ce-2dea-4e37-91ea-1ed42e110198/issue-updating-from-eval-to-volume-licenses?forum=ocsplanningdeployment
Currently done failover to another pool and users can login,
however i cant get the front end service on this server.Any pointers would be appreciated.
Praveen | MCSE Messaging 2003rit, the command is not doing the trick since its already full version,
PS C:\Users\lyncadmin> Get-CsServerVersion
Microsoft Lync Server 2013 (5.0.8308.0): Volume license key installed.
only one server in one pool, total two pools.
Lync 2013 is on Win 2008 R2, and the event in system im inclining to since i have tried all,
Log Name: System
Source: Schannel
Date: 12/30/2013 9:26:34 AM
Event ID: 36888
Task Category: None
Level: Error
Keywords:
User: SYSTEM
Computer: ACS465-BH102.me.ykgw.net
Description:
The following fatal alert was generated: 10. The internal error state is 1203.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Schannel" Guid="{1F678132-5938-4686-9FDC-C8FF68F15C85}" />
<EventID>36888</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x8000000000000000</Keywords>
<TimeCreated SystemTime="2013-12-30T06:26:34.877077500Z" />
<EventRecordID>64911</EventRecordID>
<Correlation />
<Execution ProcessID="556" ThreadID="620" />
<Channel>System</Channel>
<Computer>ACS465-BH102.me.ykgw.net</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data Name="AlertDesc">10</Data>
<Data Name="ErrorState">1203</Data>
</EventData>
</Event>
Praveen | MCSE Messaging 2003 -
MS14-055 security update for Microsoft Lync Server 2010
hello
after applying this security update do I need to Apply it to the back end database? or is that just when regular patches are applied?Hi totalnet32,
From http://support.microsoft.com/kb/2493736, we know that
"After you install the update for the Core Components server role on a Lync Server 2010 Enterprise Edition front end server, the updated SQL database files are dropped to the computer that has the Core Components server role installed.This
also applies to a Lync Server 2010 Standard Edition server. To apply the database changes, run the following cmdlets:
Install-CsDatabase -Update -ConfiguredDatabases -SqlServerFqdn <EEBE.Fqdn> -UseDefaultSqlPaths
2982388
(https://support.microsoft.com/kb/2982388/ )
MS14-055: Description of the security update for Microsoft Lync Server 2010 (Response Group Service): September 9, 2014
2982385
(https://support.microsoft.com/kb/2982385/ )
MS14-055: Description of the security update for Microsoft Lync Server 2010 (Security update for Standard/Enterprise edition Server): September 23, 2014
There's no Core Components server role update, as far as my experience, the DB update is not required.
And I suggest that reboot the Lync Servers once after the updates have been installed.
Best regards,
Eric -
OIM connector for Microsoft Lync Server
Experts,
Do we have any OIM connector for Microsoft Lync Server (previously Microsoft Office Communications Server)?
If not how can we integrate it with OIM for user provisioning ?
Please suggest.
Thanks,
S M.Hi,
Oracle doesn't have Lync connector . You can install the 11.x Exchange/AD connectors and after AD/Exch provisioning , you can write a task to execute your custom power shell which can set lync related attributes in AD/Exchange .
Hope this helps .
Regards
Suren -
Tabbed Conversations for Microsoft Lync 2010 - Corrupt .msi
This .msi for Microsoft Lync is corrupt. Where can I contact Microsoft about this?
Hi Avalanche,
I have no problem with extracting the MSI package.
Did you use this method to extract the MSI package ?
Best regards,
Eric
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected] -
Simple Question - Cisco Unified CallConnector for Microsoft Windows
Can anyone tell me if Unified Call Connector works with UCM or just Express? This is something we would be interested in if it could work with our current setup.
Will rate Post.
Thanks.Hi!
No, it does not work with CUCM, it works with express only. Please refer to the data sheet below:
"Cisco Unified CallConnector for Microsoft Windows, especially designed for the small and medium-sized business (SMB) or branch-office user, is supported by Cisco Unified Communications Manager Express 4.0 and later."
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6789/ps7046/ps7274/ps7067/product_data_sheet0900aecd8053c8ad.html
Hope this helps!
Regards,
Teresa.
If it helps, please rate :) -
Tandberg Codian MCU 4505 integration with Microsoft Lync server 2010
Hi,
We are trying to integrate Tandberg Codian MCU 4505 with Microsoft Lync server 2010.
We do not have any VCS in the setup.
If anybody has tried it before, please suggest configuration to be done on Tandberg Codian MCU 4505 and Lync server.
Regards,
RNHi,
so, i have the same environment. Lync 2013 and a cisco 1000V router on esxi with VRFs.
here is m config:
vrf definition Mgmt-intf
address-family ipv4
exit-address-family
address-family ipv6
exit-address-family
voice vrf Mgmt-intf
voice service voip
no ip address trusted authenticate
address-hiding
media disable-detailed-stats
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
bind control source-interface GigabitEthernet0
bind media source-interface GigabitEthernet0
listen-port non-secure 5066
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice class codec 2
codec preference 1 ilbc
codec preference 2 g722-64
codec preference 3 g711alaw
codec preference 4 g711ulaw
interface GigabitEthernet0
vrf forwarding Mgmt-intf
ip address 172.16.1.164 255.255.255.0
negotiation auto
dial-peer voice 15 voip
tone ringback alert-no-PI
numbering-type unknown
preference 1
destination-pattern 4.
rtp payload-type comfort-noise 13
session protocol sipv2
session target ipv4:172.16.2.207:5068
session transport tcp
voice-class codec 2
dtmf-relay rtp-nte
dial-peer voice 17 voip
numbering-type unknown
preference 1
destination-pattern 7.
rtp payload-type comfort-noise 13
session protocol sipv2
session target ipv4:172.16.1.32:5060
session transport udp
voice-class codec 2
dtmf-relay rtp-nte
gateway
timer receive-rtp 1200
sip-ua
keepalive target ipv4:172.16.2.207:5068 tcp
172.16.1.32 - Asterisk with a extensions on it.
172.16.2.207 - Lync 2013 mediation server with other extension on it
i can call from Asterisk extension via router and to Lync extension.
i cannot call from Lync to Asterisk.
TCP session with the router from Lync on port 5066 does not come up. three way handshake seems to come up.
strange. lync person seems to configured everything correctly
any thoughts? -
How to set up Qos for Microsoft Lyncs 2013 in cisco Switches and Router
Hi
as i am new to Qos part , please send the complete qos configuration command has to apply in my cisco 2960s switchs as well as 4506 chassis(L3 mode act as my router).
as i know from microsoft, DSCP 46 and 34 should give highest priory
please send the completed configuration for priorities this DSCP
thanks
SujishHi,there,
The rule setting should be same as in Exchange 2010,you can configure it via outlook or OWA if you have full access permission. I also believe it should be something related to Repliation,would you please check the event log to see if the
AD and Exchange replication has completed.
In some cases, replication can take longer depending on how many AD sites and Exchange servers in the environment:
http://support.microsoft.com/kb/148381
http://support.microsoft.com/kb/158989
Hope these useful!
Regards,
Sharon
Sharon Shen
TechNet Community Support
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. -
Cisco USB Driver for Microsoft Windows 7 PC?
Hello All,
I want a USB Driver for the USB Console cable which came up with Cisco Router.
Note that this USB Console cable has both the sides USB ports ( 1 side of the port goes to USB Console Port of Router and other side goes to USB port of your Laptop)
I searched on cisco.com.
Found the below link:
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6880_x/hardware/installation/guide/b_c6880-X_hig/b_c6880-X_hig_appendix_01001.pdf
However, when I go to download link, it appears as "Page Not Found"
I want to try this option and connect my Laptop's HyperTerminal to Router's USB Console.
Does anyone know the USB driver for this?
Thanks
ChinarHi Chinar-
It looks like this will work with Windows 7.
http://software.cisco.com/download/release.html?mdfid=282867574&softwareid=282855122&release=3.1
DJ -
RSA SecurID and Cisco ACS integration for user(s) with enable mode
I thought I had this problem figured out but I guess not.
I have a Cisco 2621 router with IOS 12.2(15)T17. Behind the
router is a Gentoo linux, RSA SecurID 6.1 and Cisco ACS 3.2.
I use tacacs+ authentication for logging into the Cisco router
such as telnet and ssh. In the ACS I use "external user databases"
for authentication which proxy the request from the ACS over
to the RSA SecurID Server. I installed RSA Agents with
sdconf.rec file on the Cisco ACS server. I renamed "user group 1"
to be "RSA_SecurID" group. In the "External user databases" and
"database configurations" I assign SecurID to this "RSA_SecurID"
group.
Everything is working fine. In the "User Setup" I can see dynamic
user test1, test2,...testn listed in there as "dynamic users". In
other words, I can telnet into the router with my two-factor
SecurID.
The problem is that if test1 wants to go into "enable" mode with
SecurID login, I have to go into "test1" user setting and select
"TACACS+Enable Password" and choose "Use external database password".
After that, test1 can go into enable mode with his/her SecurID
credential.
Well, this works fine if I have a few users. The problem is that
I have about 100 users that I need to do this. The solution is
clearly not scalable. Is there a setting from group level that
I can do this?
Any ACS "experts" want to help me out here? Thanks.That is not what I want. I want user "test1" to be able to do this:
C
Username: test1
Enter PASSCODE:
C2960>en
Enter PASSCODE:
C2960#
In other words, test1 user has to type in his/her RSA token password to get
into exec mode. After that, he/she has to use the RSA token password to
get into enable mode. Each user can get into "enable" mode with his/her
RSA token mode.
The way you descripbed, it seemed like anyone in this group can go directly
into enable mode without password. This is not what I have in mind.
Any other ideas? Thanks. -
IDD Authorization Code for Microsoft Lync Voice
Hello Friends,
We are in need to provide an IDD Authorization module for Lync Voice. When the user make an IDD call, user should use an Authorization or Pin code. For invalid codes the IDD call should be restricted as well.
I wonder whether Lync naturally support such feature?
Or, should we need to place some server side application in between?
Any enlightening is greatly appreciated and thanks a lot in advance.
thank u
Life is a Gift. To be a GiftYeah, to get the dial plan/route trick to have personal pins, you're either talking about multiple dial plans and routes, or one large one with multiple pins inside of it. If you needed different pins for thousands of users, that just wouldn't
be feasible. For fewer, this might be an interesting script to automate or manage it.
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications -
DUET Enterprise vs BO BI Integration Option for Microsoft Sharepoint
I am struggling to find the right management overview to position DUET Enterprise vs BO BI Integration for Microsoft Sharepoint.
My high level definition of DUET Enterprise is to expose SAP Data and Processes into the Microsoft Sharepoint Environment (especially for non professional user = casual user).
Obviously these casual users need to see, to retrieve or to refresh some BW reports (knowing we are using or will use BO BI 4.0).
It seems DUET Enterprise does not support this scenario .... and we need to use another solution called : BO BI Integration Option for Sharepoint (detailed doc [here|http://help.sap.com/businessobject/product_guides/boexir4/en/400sp2_ioms_getstarted_en.pdf]).
I am confused (I can not picture it) why we need 2 different products (medium - long term).
Could you somebody explain :
1. to confirm we need currently these 2 products
2. why we will need 2 different products in the future ?
Thanks.Hi Patrick,
I was also trying to find some information this topic for the last few days when I came across your thread. There has been a similar discussion earlier in [this SDN thread|Duet Enterprise vs BO Integration Option for Microsoft Sharepoint u2013 IOMS;.
After seeing the capabilities of IOMS, I can say these two products are very different. IOMS has different web parts to render BO/BW dashboards, reports ect. whereas Duet Enterprise is an integration platform for connecting various SAP systems (of type ABAP now), using which we can view/operate on any SAP object, integrate workflow and fetch SAP reports as document.
Duet Enterprise provides SSO and role based access to SAP data which seems to be missing in IOMS.
At this point it seems both these products have different capabilities with similarities in report publishing (Duet Enterprise can only publish reports from BI and other ABAP based system directly to SharePoint document library; not sure what IOMS does in this area).
I guess at this point if your requiremtn is to only provide a SharePoint based frontend to Bo/BI IOMS has to be used, however if you need to build applications with SAP data or around SAP processes Duet Enterprise has to be used. -
Question about cisco unified callconnector for mscrm
Hi
I've successfully installed software on both workstation and MSCRM server, and it works well.
However, when I use "click to call" in MSCRM, a blank window keep poping up with message "The webpage you are viewing is trying to close the window. Do you want to close the window?"
My question is how to let IE close the window without the confirmation window.
I found some people use following Javascript to close the IE window.
<script language=javascript>
function CloseWindow()
window.open('','_self','');
window.close();
</script>
However, if anyone can let me know where is the place to add this code into, I would appreciate
Thanks
EricHi!
No, it does not work with CUCM, it works with express only. Please refer to the data sheet below:
"Cisco Unified CallConnector for Microsoft Windows, especially designed for the small and medium-sized business (SMB) or branch-office user, is supported by Cisco Unified Communications Manager Express 4.0 and later."
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6789/ps7046/ps7274/ps7067/product_data_sheet0900aecd8053c8ad.html
Hope this helps!
Regards,
Teresa.
If it helps, please rate :)
Maybe you are looking for
-
Returnable packaging in scheduling agreements and inbound deliveries
Hi all, We are trying to make the following process work but are finding some problems. We have packaging materials of type LEIH which we want to include in a scheduling agreement. This we where able to do by using account assignment key "Z". By doin
-
Installation of Solaris 10 on Dell Optiplex 745
Hi, I am new to Solaris. I am planning to install Solaris 10 10/08 on my Dell Optiplex 745 with the following config, Processor: Intel Core 2 Duo 6300 @ 1.86 GHz No if Bits: 64 Bits RAM: 2 GB HDD: 160GB Monitor: Dell 17" Plug and Play I would like to
-
Modifying Lightroom Flash Gallery Templates
I have created a Photo Gallery using Lightroom Flash Gallery in Bridge CS5 and have integrated it into a web site so far so good. I would like to replace the file name shown under the image with the Image Title from the Metadata and not to show the T
-
hello, what table i can found the cost center i createdin tcode KS01. thanks. donna
-
Power Teacher Gradebook won't run with Yosemite
Hello everyone, I recently updated to Yosemite, I was previously lion 10.7.5, my java was and still is version 7. The application power teacher grade book now will no longer launch on my computer even though I haven't updated the Java which was the p