Cisco UC520 Upgrade

Hi,
i have a UC520، and it show the below error:
"Oct 6 09:47:31.695: %SCHED-2-EDISMSCRIT: Critical/high priority process VTSP may not dismiss. -Process= "VTSP", ipl= 0, pid= 236, -Traceback= 0x80E728F8 0x8209D2D8 0x80E5ACA0 0x80E8BFD0 0x80E8A9E8 0x80E8BAF0 0x8213A018 0x8213A278 0x8213A628 0x8213131C 0x82132600 0x80B47F24 0x80851530 0x80859A04 0x82DB8848 0x82DB8FB0"
And i was read the error related to bug, and the upgrade is the solution of this bug, so we will go into upgrade, does i need to upgrade the whole package like below link :
https://supportforums.cisco.com/docs/DOC-10315
or i can just upgrade the IOS? and if i will upgrade the IOS deos it affect the system Cisco Unity Express.
The Second question,if i need to upgrade the whole package, does the upgrade need license?
the Licence on my UC500 like below:
sh license feature
Feature name             Enforcement Evaluation Clear Allowed Enabled
uc500-16u-upgrade        yes          yes         no             no
uc500-32u-upgrade        yes          yes         no             no
uc500-24u-to-48u-upgrade yes          yes         no             no
uc500-48u-upgrade        yes          yes         no             no
uc500-48u-to-64u-upgrade yes          yes         no             no
sh platform software license
Upgrade license              : uc500-48u-to-64u-upgrade
License status               : Not in Use
License UDI                  : UC520-48U-T/E/F-K9:FHK1350F06G
Maximum User Licenses        : 56
Used User Licenses           : 38
Available User Licenses      : 18

So if i upgrade to the "uc500-advipservicesk9-mz.151-4.M6" IOS this will upgrade the CME, and it may solve this Error.
but if i will upgrade the whole UC500 does this require license?

Similar Messages

Cisco MARS Upgrade available - 4.2.3

Cisco MARS upgrade has been posted to Cisco's web site. It is a large upgrade and has special instructions.
I did not see any notes for support of Cisco IPS 6.0 new fields.
Web Site
http://www.cisco.com/cgi-bin/tablebuild.pl/cs-mars

thanks for the post! holy crap, you weren't kidding...>1GB???

Cisco ise upgrading and licences

I nedd to upgrade from version 1.1.2 patch 4 to 1.1.3
the deployment is distributed so the split deployment technique needs to be used:
http://www.cisco.com/en/US/docs/security/ise/1.1.1/upgrade_guide/upg_dis_dep.html#wp1052969
the guide is quite hard to follow as there are some licensing informations missing that can potentially cause service downs:
in particular my questions reguarding the guide are:
--- OUR licence is registered to the primary PAN node only----
1) Deregistering primary PSN "D" node : what licence it will use? the inherited (10000 endpoints) or will it lose the licence completely and lock the network authentications?
2) When node "B" will be deregistered and will become standalone what happens to its licence ? will it be lost? and what will happen to the node "D" when added back to the node "B" ?
3) when I will switch back node "A" (after upgrade and registration to node "B") to its previous primary PAN state it is stated that the licence needs to be reloaded in it cause it was lost when adding it to node "B".... and in the meanwhile? no node will authenticate cause the primary node is without a licence?
TY

Giuliano,
De-registered node will always use it's own license, i.e. it becomes standalone box without knowledge or information of anything around it. Either the evalutaion or whichever license you have supplied it with.
License enforcement is performed by active admin node in cluster, according to its license.
Have a look at:
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCug04405
I don't think license needs to be reloaded, but that may be just my memory not serving me. I'll double-check that one.
M.

Cisco ASA Upgrade from 7.0(8) to 8.2(1)

Hi, i need to upgrade my 5510 ASA from 7.0(8) to 8.2(1) ( Please note its different query from my last thread)
what i found online is i will have to do this upgrade in sequence, that is
7.0.x -> 7.2.x --> 8.0.x --> 8.2.1
is that correct?
or i will go to 7.1.x first? like this
7.0.x--> 7.1.x -> 7.2.x --> 8.0.x --> 8.1.x--> 8.2.1
Please guide, Also i am assuming, reboot required after every upgrade right?

ok, i found something on another Cisco document. that is what i thought
To ensure that your configuration updates correctly, you must upgrade to each major release in turn. Therefore, to upgrade from Version 7.0 to Version 8.2, first upgrade from 7.0 to 7.1, then from 7.1 to 7.2, and finally from Version 7.2 to Version 8.2 (8.1 was only available on the ASA 5580). "

How often does cisco do upgrades to their kickstart and OS? Is there a bulletin date or some kind of notification?

I am starting to work with Cisco Switches, I have 12 Nexus 6000 series and 2 Nexus 7000 series (core switches) I just upgraded to kickstart 7.1(0)N1(1). and OS 7.1(0)N1(1)......However I want to know if there is a specific date or dates that Cisco releases new upgrades so I can be prepare. Can someone help me with this? Thank you so much.

Not that I know of, however it's not a bad suggestion. I'd recommend posting to www.apple.com/feedback. Don't expect to hear back though.

Cisco IRONPORT UPGRADE keep failed

Hi all,
I try to upgrade one of the ironport s170 version 7.1.3-031, but it keep failed.. and the upgrade process very slow. Any idea??

Hey Vince,
I was actually trying to get your view of what seems to be the issue and I highlighted the ETA because that was a big number.
I would recommend you to start fresh. Reboot the box, and try the upgrade again. The reboot would clean the temporaty files if any could be interfering.
Try the upgrade from the CLI and choose the most recent version of AsyncOS available.
Upgrade issues are usually but not always related to bandwidth control, proxy, network latency, file system corruption. A packet capture could help to identify proxy limiting and some other network related issues but you can also try Local Upgrade.
How do I get a packet capture (tcpdump) from a Web Security Appliance or a Email Security Appliance?
Knowledge Base Answer ID: 628
http://tools.cisco.com/squish/Ae538
Comprehensive Guide to Local Upgrade Servers
Knowledge Base Answer ID: 1558
http://tools.cisco.com/squish/212fd
From the screenshot also, we cannot get the current version you have running but I am guessing it is an old version. Another reason to support the upgrade. It is possible your appliance is not listed as authorised to get upgrades. If you cannot upgrade using Local Upgrade process described in the article above, you should definitively open a support ticket so the engineers can check the appliance's status and assist you further.
I hope this helps.
Regards,
-V

Cisco EA4500 Upgrade causes ipad (1) issues especially with netflex

I just upgraded Routers to a Cisco EA4500 (N900) router. Now Netflix will stop every 30-40 seconds to buffer. Speed test on ipad shows 7MB+ every time I have tested... Any ideas?

are you still haveing this issue if you use the old router?

Cisco commonservices upgrade query

Hi All ,
I am running with cisco common services 3.1 version . I want to upgrade the same to 3.2 .
Please guide me from where can i download the Software in cisco site
Thanks in Advance
Regards
Angus

Hi Angus,
You can download LMS 3.2 from www.cisco.com\go\lms
At the bottom of the page, Under the Featured Contents , click on Evaluate LMS Solutions > on the next page click on --> Network Management Evaluation Products .
There you will find :-
CiscoWorks LAN Management Solution (WINDOWS OS) 3.2
CiscoWorks LAN Management Solution (SOLARIS OS) 3.2
License of LMS 3.1 will be valid for LMS 3.2 as well. Though its evaluation version but its complete setup, so if you will run the setup on top of LMS 3.1, this will installed LMS 3.2 as complete setup and license version.
LMS 3.2 Install Guide :-
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/install/guide1/lmsigsg.html
Here are the Tips for successfull LMS installation pen by Joseph Clarke :-
https://supportforums.cisco.com/docs/DOC-9132
Note :- Its good to take the backup of CiscoWorks LMS 3.1 before doing any upgrade.
Many Thanks,
Gaganjeet

Cisco ACS upgrade

Hello,
is it possible to upgrade from ACS v.3.3 directly to 5.2 ? Or do I need version 4.X in between?
Thanks for your help.

You can't upgrade ACS 3.3 directly to ACS 5.2.
ACS 5.x is completely different to ACS 3.x and 4.x.
There is specific hardware that you need to run ACS version 5.x, and here is the list:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.2/release/notes/acs_52_rn.html#wp70853
Here is the migration guide to ACS 5.x:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.1/migration/guide/Migration_Book.html
Hope that helps.

Cisco 1252 upgrade from standalone autonomous to LWAPP

Hi All,
Can somebody please guide me through the process of upgrading Cisco 1252 access point from Autonomous to Light Weight
iam attaching show version log which gives information about current IOS
on the access point & its in standalone mode now.
Any help would be greatly appreciated.
Cheers,
Satish

Hi Satish,
These two great threads discuss the methods to make this conversion;
From Steve, Leo and Charles;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&topicID=.ee6e8b8&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc2c5c3/0
From Scott and Steve;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&topicID=.ee7c7c3&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc2fd83/0
Hope this helps!
Rob

Cisco 7911G Upgrade form SSCP to SIP using TFTP

Hi All,
I am upgrading the Cisco 7911G phone from SCCP to SIP. i dont have Call manager.
How i can upgrade from SCCP to SIP using TFTP server on my PC.
your input will be appericiated.

Have u done it???

Cisco WAAS Upgrade HW Support

Hi.
I need to upgrade my WAAS solution from Release 5.3.5 to 5.4.1, but I do not find any information about my Hardware in version 5.4.1.
Is this hardware supported on version 5.4.1?
WAE-674
WAE-574
SM-SRE-700-K9
Regards,
Paulo Soares

I have Upgraded the image, and still I get the following:
sabf-0004-centraloff-wae-1#sh accelerator
Accelerator     Licensed        Config State    Operational State
cifs            Yes             Enabled         Shutdown
epm             Yes             Enabled         Shutdown
http            Yes             Enabled         Shutdown
mapi            Yes             Disabled        Shutdown
nfs             Yes             Enabled         Shutdown
ssl             Yes             Enabled         Shutdown
video           No              Enabled         Shutdown
sabf-0004-centraloff-wae-1#sh alarms
Critical Alarms:
        Alarm ID                 Module/Submodule               Instance
   1 svcdisabled               nodemgr                      sodre_stats
Major Alarms:
None
Minor Alarms:
None
sabf-0004-centraloff-wae-1#sh version
Cisco Wide Area Application Services Software (WAAS)
Copyright (c) 1999-2011 by Cisco Systems, Inc.
Cisco Wide Area Application Services Software Release 4.4.3c (build b9 Nov 29 2011)
Version: oe7371-4.4.3c.9
Compiled 16:12:50 Nov 29 2011 by damaster
Device Id: 00:1a:64:c9:a2:0c
System was restarted on Fri Dec 30 07:00:47 2011.
The system has been up for 17 minutes, 50 seconds.

Cisco Ucs upgrade from 1.4(3m) to 2.1(1a)

hi!!
I need to do an upgrade from 1.4(3m) to 2.1(1a)!
i've 3 chassis 5108 ( 6 fex 2104xp ) with server B200 M2 and B440 M2. i've two Fi 6120Xp in cluster mode.
i've check the prerequisite to upgrade but i've a question about default zoning;
iv'e brocade switch 5300 ( fw v6.4.1 ) attached to Fi 6120xp
i've SAN configured :
i've no other configuration under San Tab.
The documentation says:
"Default Zoning is Not Supported in Cisco UCS, Release 2.1(1a) Onwards.Default zoning has been deprecated from Cisco UCS, Release 2.1(1a) onwards. Cisco has not supported default zoning in Cisco UCS since Cisco UCS, Release 1.4 in April 2011. All storage connectivity that relies on default zoning in your current configuration will be lost when you upgrade to Cisco UCS, Release 2.1(1a) or a later release. We recommend that you review the Fibre Channel zoning configuration documentation carefully to prepare your migration before you upgrade to Cisco
UCS, Release 2.1(1a) or later."
Can i upgrade to 2.1 (

hi!!
I need to do an upgrade from 1.4(3m) to 2.1(1a)!
i've 3 chassis 5108 ( 6 fex 2104xp ) with server B200 M2 and B440 M2. i've two Fi 6120Xp in cluster mode.
i've check the prerequisite to upgrade but i've a question about default zoning;
iv'e brocade switch 5300 ( fw v6.4.1 ) attached to Fi 6120xp
i've SAN configured :
i've no other configuration under San Tab.
The documentation says:
"Default Zoning is Not Supported in Cisco UCS, Release 2.1(1a) Onwards.Default zoning has been deprecated from Cisco UCS, Release 2.1(1a) onwards. Cisco has not supported default zoning in Cisco UCS since Cisco UCS, Release 1.4 in April 2011. All storage connectivity that relies on default zoning in your current configuration will be lost when you upgrade to Cisco UCS, Release 2.1(1a) or a later release. We recommend that you review the Fibre Channel zoning configuration documentation carefully to prepare your migration before you upgrade to Cisco
UCS, Release 2.1(1a) or later."
Can i upgrade to 2.1 (

UC520 Upgrade

Hi guys,
which is the best way to upgrade a UC520 (CME: 7.0 CUE: 7.0.3) to software pack 8.6.1 (CME: 8.6 CUE: 8.6.5)?
first upgrade the CUE and then the CME?
Thanks.
Cristian

If you want to use CCA, follow CCA directions.
If you want to use CLI, it makes no difference.

Cisco Works upgrade

I'm currently running LMS3.2 and ordered an upgrade, Cisco sent me an electronic version of L-CWLMS-4.0-1.5KUP with a PAK in it but I was expecting a DVD version. I assume that I need to download/install an eval version and then enter the PAK to make it permanenet, please correct me if I'm wrong. I don't think I can upgrade over my existing LMS3.2, I beleive I will need to wipe out my existing LMS and start from the fresh.
Thank you all.

In addition to Michel's correct answer, I would add two things:
1. The current LMS version is 4.1, not 4.0. If you're going to the trouble to upgrade, it should be to the current version.
2. You can preserve your device list and other settings by backing up your LMS 3.2 and then restoring the data into the new LMS 4 installation. Follow the procedures here.
Whether or not you migrate your data, you should be reading and closely following the Installation Guide. LMS is very unforgiving of one not having all of the prequisites correctly established and procedure not followed.

Cisco UC520 Upgrade

Similar Messages

Maybe you are looking for