Cisco UCS C220-M3 Server doesn't boot after adding Intel I350 Quad Port NIC

Hello,
We have purchased 2 Cisco UCS C220-M3 rack mounted servers (Single Processor) that have a dual port I350 LOM. We also purchased two Intel I350 Quad Port NICs to expand the available ports on each server from 2 to 6.
The problem we are facing is that the server will not complete the boot process unless we disable either the LOM or the Quad Port NIC. We have tried numerous settings in the BIOS area but we haven't managed to have them both working.
The I350 Quad Port NICs are from Intel and not from Cisco and we are running the latest FW/BIOS on the Servers as of March 10 2015.
We have followed the steps described in the installation guide to install them.
Could you provide some light in this situation please, what are our options?
P.S. Although the LOMs are I350, the MAC Address Vendor is Cisco, is it possible that Cisco servers accept only Cisco Branded Expansion Cards?
Thank you,
George

Hi Shawn,
At least I'm not the only one having the same problem!
You are trying to use the cards with the LOMs enabled?
Which screen are you referring to in the first paragraph of your message?
Mine sits in BIOS POST for about 10 minutes and then resets itself....
We are also waiting for an answer from Cisco, so any findings/news will be posted here.
Thanks,
George

Similar Messages

Cisco UCS C220 MS SFF won't boot past BIOS screen with 2x1.2TB SAS drives installed

We have been running a few of these servers with only a 500GB 6GB SATA 7.2K drive installed with all VM's (Hyper-V) sitting on an attached SAN.
For various reasons we needed some local storage on the server and installed 2 1.2TB SAS drives (10K 2.5"). They hot installed okay but the server had to be brought down to enter the MegaRaid software to configure the RAID.
Unfortunately with the drives installed, the server won't boot past the initial BIOS screen and certainly doesn't get to the RAID screens.
Does anybody have any idea why this would happen? Is there some BIOS update required to support these drives and/or MegaRaid software upgrade?
The servers are up and running at the moment so I can't find the version of the RAID software running.
Thanks
Larry

Hi Lauren,
If you don't have a PCI or a mezzanine based controller and you are using the embedded raid controller you need a chip for the embedded raid controller to support SAS drives. By default the embedded controller only supports SATA drives. See page 9 of the link below
Please let me know if you are not using the embedded controller
http://www.cisco.com/c/dam/en/us/products/collateral/servers-unified-computing/ucs-c-series-rack-servers/C220M3_SFF_SpecSheet.pdf

Cisco UCS C220 M3S Server OS random shutdowns

Hello good day, I am facing some issues with the Cisco UCS indicated in the subject, I have created a Raid 1 beetwen 2 HDD's of 1 TB each one, also upgraded the firmware of the UCS with the 2.0(3f) HUU tools, and upgraded everything. Then I installed Windows Server 2012 R2 Eval version (I have a proper license to install but wanted to test the OS first). Now some times the OS/Server just shutsdown, and whenever I go in to the Web GUI to check it out, it's actually powered down, I have checked the "Faults and Logs" --> System Event Logs, and I can see this happening:
*The timestamp is from below to the top on both logs*
MAIN_POWER_PRS: Presence sensor, Device Removed / Device Absent was asserted
Microsoft OEM event data record, Record type: DD, Sensor Number: 0A, Event Data: 00 00 00, Raw SEL: 37 01 00 35 0A 00 00 00 00
(About this message with the HEX Values, it's always repeating it self with other values)
System Software event: OS Stop sensor, OS Graceful Shutdown was asserted
In the IMC Log this is what showed when it powered down:
Bridge.c:1484:audit Resp:0x0
Bridge.c:1478:audit from:kcs Fn:0x0 Cmd:0x6 Data: 0x30 0x4
obj/../../src/BiosSecureBootAgent.cc:101:BiosSecureBootAgent --> m_valid_state = [ 0 ] #012 m_enable_state = [ 0 ] #012 m_setupMode_state = [ 1 ] #012 m_secureBoot_state = [ 0 ]
obj/../../src/BiosSecureBootAgent.cc:63:get=uefiSecureBootState Received
bootordermgnt.cpp:2392:WriteBIOSDeviceCfg: Successfully renamed file: /mnt/jffs2/ConfigPolicy.xml.bak to /mnt/jffs2/ConfigPolicy.xml
bootordermgnt.cpp:1310:StoreDeviceCfg: Successfully renamed file: /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT.bak to /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT
bootordermgnt.cpp:2392:WriteBIOSDeviceCfg: Successfully renamed file: /mnt/jffs2/ConfigPolicy.xml.bak to /mnt/jffs2/ConfigPolicy.xml
bootordermgnt.cpp:1310:StoreDeviceCfg: Successfully renamed file: /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT.bak to /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT
bootordermgnt.cpp:2392:WriteBIOSDeviceCfg: Successfully renamed file: /mnt/jffs2/ConfigPolicy.xml.bak to /mnt/jffs2/ConfigPolicy.xml
bootordermgnt.cpp:1310:StoreDeviceCfg: Successfully renamed file: /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT.bak to /mnt/jffs2/avct_ems_cfg/BMC_Data/BOOTDEV.DAT
bootordermgnt.cpp:1367:No Precision Boot DB exists..migrate old relase configuration to Precision Boot format!
sanluis1/platform.c:116:platform_event_enable_tick_end: Configuring IR from CIMC
(A bunch of these with other values) common.c:945:Enabling sensor scan for sensor 0x85.
lv_dimm.c:403:[handle_event_enable_tick]enable sensor event
lv_dimm.c:220:[transition_function]Transition to [High Voltage Mode] Success
lv_dimm.c:200:[transition_function]Starting Transition to [High Voltage Mode] from [Unknown Mode]
(A lot of these with different values) common.c:940:Disabling Sensor scan for sensor 0x89.
lv_dimm.c:129:[lpc_reset_seen]LPC Reset Count is Different [0x15:0x16] Asserted LPC Reset Seen
selparser.c:678: # 1D 03 00 00 01 02 00 00 DB F7 EF 54 20 00 04 25 05 00 00 00 08 00 FF FF # 31d | 02/27/2015 04:51:39 | CIMC | Entity presence MAIN_POWER_PRS #0x05 | Device Absent | Asserted
Received event_ipmi_power_state_change Event (type=4, size=0)
video_trigger.c:262:Sending event_ipmi_power_state_change (OFF) .
WatchdogTimer.c:1467:Current Configuration of Watchdog timer is now stopped.
Pilot2SrvPower.c:466:Blade Power Changed To: [ OFF ]
<5>[se_pilot2_wakeup_interrupt]:2561:USB HS: VDD Power = OFF
<6>drivers/bmc/usb/usb1.1/se_pilot2_udc_usb1_1.c:2540:USB 1.1 is now disconnected.
<5>drivers/bmc/usb/usb1.1/se_pilot2_udc_usb1_1.c:2288:USB FS: VDD Power WAKEUP- Power Good = OFF
<7>[slp_state_isr]:117:Signals SLP3n[ Asserted ] SLP5n[ Asserted ]
<6>[platform_power_state_irq_handler]:18:VDD_PWR_GOOD: Deasserted
In the event viewer of the Windows Server 2012
This is the UCS specifications:
CPU 1: Intel(R) Xeon(R) CPU E5-2609 v2 @ 2.50GHz
CPU2: Intel(R) Xeon(R) CPU E5-2609 v2 @ 2.50GHz
Memory: 16 GB
There is something really itching, is it because I have Evaluation version of the Windows Server...?
Regards.

Ok, I feel kind of dumb now, I have checked the tech evaluation page on Microsoft, and if it's not connected to the internet it will not inherit the three months evaluation trial, which I thought would come activated already, and only allows you up to 10 days grace period with the rearm command .... :/
The process C:\Windows\system32\wlms\wlms.exe (WIN-UDPFG5O0K37) has initiated the shutdown of computer WIN-UDPFG5O0K37 on behalf of user NT AUTHORITY\SYSTEM for the following reason: Other (Planned)
Reason Code: 0x80000000
Shutdown Type: shutdown
Comment: The license period for this installation of Windows has expired. The operating system is shutting down.
This is what made me check it out today, I will connect it to the internet and let it activate... Meanwhile the command for the 10 days grace is:
Slmgr /rearm
Shutdown –r
Like always.

Cisco UCS C220 with VIC 1225

Hello,
We have Cisco UCS C220 M3 with VIC 1225 card installed. We connected only one 10G port of VIC 1225 to Nexus 5548UP switch. But I do not see this port on switch and in CIMI the status for this port shows Link Down. I wanted to to iSCSI boot from storage NetApp FAS2240 but since I don't see this port on my Nexus switch I am unable to do boot from NetApp. I tried both ports on VIC 1225 with same result. Please I need help in this matter. I know I am missing something very simple but can't figure this out.
Thanks,
Salman

Hi Kenny,
Here is the answers:
-What slot is this card installed in?
Mezzenine
-How many CPUs does the server have installed? (1 OR 2 CPUs can make the difference)
2x 2.90 GHz E5-2690/135W 8C/20MB Cache/DDR3 1600MHz
-Is the PCIe slot enabled in BIOS? << Let us know if you don't know how to check it from CIMC
I believe I did. Server>BIOS>BIOS advanced> PCIe (Let me know if this correct)
-Have you confirmed that the cable is good?
I have changed four cables. I am using SFP-H10GB-CU2M= Twinax cable.
-If the switch does not even see the port and CIMC says it is down, have you confirmed the switch port is properly configured?
CIMI says “Link Down” in VIC adapter General area. The switch interface config has only “switchport mode access” in default vlan 1.
-What is the firmware running on the server and the OS?
We upgraded the firmware with latest ucs-c220-huu-1.5.4-3.iso.
Let me share with you the complete BoM of the server:
UCSC-C220-M3S              1x UCS C220 M3 SFF w/o CPU mem HDD PCIe PSU w/ rail kit
UCS-CPU-E5-2690              2x 2.90 GHz E5-2690/135W 8C/20MB Cache/DDR3 1600MHz
UCS-MR-1X082RY-A    16x 8GB DDR3-1600-MHz RDIMM/PC3-12800/dual rank/1.35v
CAB-9K10A-UK              2x Power Cord 250VAC 10A BS1363 Plug (13 A fuse) UK
UCSC-PCIE-CSC-02    1x           Cisco VIC 1225 Dual Port 10Gb SFP+ CNA
UCSC-PCIE-QSFP              1x Qlogic QLE8242-CU Dual Port 10 GbE FCoE CNA
UCSC-HS-C220M3              2x Heat Sink for UCS C220 M3 Rack Server
UCSC-RAIL1              1x Rail Kit for C220 C22 C24 rack servers

Unable to enable HBA Card in the Cisco UCS c22 m3 server

Hi All,
I need your help desperately to setup the cisco ucs c22 m3 server in our environment. We have a C22 M3 server and I did the basic config of CIMC and we have a LSI megaraid controller connected to one of the PCIe and the other PCIe has a dual port 8gb HBA card. We installed the RAID and we can see the LSI Megaraid controller. But I cannot see the HBA card and there is noo light near the card. I hope I need to enable something so that the card should work. I tried enabling in the BIOS menu I can see the PCIe slot is enabled but I am unable to see the HBA functioning. Couldyou pleasehelp me to resolve this.

Dear Manuel,
Thanks for replying me. See the answers for your queries.
What kind of HBA card are you trying to use?
If I am not wrong we are using "Qlogic QLE2562, 8Gb dual port Fibre Channel HBA".
How many CPUs do you have installed on your server?
I opened the box and saw only 1 CPU installed. But the solution is given by CISCO pre sales. We have 2 PCIe slots configured. One for LSI RAID controller and the other with dual port Fibre Channel HBA.
Awaiting your reply.
Thanks and Regards,
Jaffer Ali

Cisco UCS C210 M1 server certified for Unified Communications

Hello:
Our VAR is telling us that HP and Cisco are splitting up. We're an HP shop today and the MCS 7800-H series routers were a perfect fit. Our VAR is now telling us we have to go with the rebranded IBM systems. BUT I would like to avoid the IBM servers. And the Cisco servers look attractive. But I've been unable to determine if the Cisco UCS C210 M1 server is certified for various Unified Communications applications (Communications Manager, Unity, Cisco Emergency Responder, ICM, CVP, etc.).
Has anyone heard of any Unified Communications deployments on UCS hardware?
Thanks,
Ken

Mr. Schroeder:
Thank you for the information. Timing is everything. We'll likely have to order our equipment in May of this year. I'd love to start getting Cisco UCS hardware in. Oh well... maybe next year!

Mac Mini server won't boot after logoff, any suggestions?

My mac Mini Server will not boot after administrator logoff, I get a gray screen with the spinning progress wheel, but nothing happens. Any suggestions?

Can you boot into single user mode? If so, run fsck and post the results.

Mail server doesn't work after upgrading from SL to ML

My Mail server doesn't work after upgrading from SL to ML
Mail client connects with the Mail Server wich seems to run but then they can't receive any email...
the problem seems to be related with dovecot ... in my smtp log i get this:
relay=dovecot, delay=324, delays=324/0.02/0/0.01, dsn=4.3.0, status=deferred (temporary failure. Command output: pipe: fatal: pipe_command: execvp /usr/libexec/dovecot/deliver: Permission denied
I have to say that in the usr/libexec there wasn't the dovecot directory so I just tried to create one but with no luck
Any Ideas?
Cheers
Carlo
This is my postconf -n info:
server:Data admin$ postconf -n
biff = no
command_directory = /usr/sbin
config_directory = /Library/Server/Mail/Config/postfix
content_filter = smtp-amavis:[127.0.0.1]:10024
daemon_directory = /usr/libexec/postfix
data_directory = /Library/Server/Mail/Data/mta
debug_peer_level = 2
debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin xxgdb $daemon_directory/$process_name $process_id & sleep 5
dovecot_destination_recipient_limit = 1
enable_server_options = yes
header_checks = pcre:/etc/postfix/custom_header_checks
html_directory = /usr/share/doc/postfix/html
imap_submit_cred_file = /Library/Server/Mail/Config/postfix/submit.cred
inet_interfaces = all
inet_protocols = ipv4
mail_owner = _postfix
mailbox_size_limit = 0
mailbox_transport =
mailq_path = /usr/bin/mailq
manpage_directory = /usr/share/man
maps_rbl_domains =
message_size_limit = 20971520
mydestination = $myhostname, localhost.$mydomain, localhost
mydomain = moremoremore.it
mydomain_fallback = localhost
myhostname = server.moremoremore.it
mynetworks = 127.0.0.0/8,192.168.178.0/24
newaliases_path = /usr/bin/newaliases
queue_directory = /Library/Server/Mail/Data/spool
readme_directory = /usr/share/doc/postfix
recipient_delimiter = +
relayhost = mail.mclink.it
sample_directory = /usr/share/doc/postfix/examples
sendmail_path = /usr/sbin/sendmail
setgid_group = _postdrop
smtp_sasl_auth_enable = no
smtp_sasl_password_maps =
smtpd_client_restrictions = permit_mynetworks permit_sasl_authenticated reject_rbl_client zen.spamhaus.org permit
smtpd_enforce_tls = no
smtpd_helo_required = yes
smtpd_helo_restrictions = reject_invalid_helo_hostname reject_non_fqdn_helo_hostname
smtpd_pw_server_security_options = cram-md5,gssapi
smtpd_recipient_restrictions = permit_sasl_authenticated permit_mynetworks reject_unauth_destination check_policy_service unix:private/policy permit
smtpd_sasl_auth_enable = yes
smtpd_tls_CAfile = /etc/certificates/server.moremoremore.it.A358901573EE7B9B4D489725407934780D24D5 36.chain.pem
smtpd_tls_cert_file = /etc/certificates/server.moremoremore.it.A358901573EE7B9B4D489725407934780D24D5 36.cert.pem
smtpd_tls_exclude_ciphers = SSLv2, aNULL, ADH, eNULL
smtpd_tls_key_file = /etc/certificates/server.moremoremore.it.A358901573EE7B9B4D489725407934780D24D5 36.key.pem
smtpd_use_pw_server = yes
smtpd_use_tls = yes
tls_random_source = dev:/dev/urandom
unknown_local_recipient_reject_code = 550
virtual_alias_maps =
server:Data admin$

if this could help:
mail:setStateVersion = 1
mail:readWriteSettingsVersion = 1
mail:connectionCount = 11
mail:servicePortsRestrictionInfo = _empty_array
mail:protocolsArray:_array_index:0:status = "ON"
mail:protocolsArray:_array_index:0:kind = "INCOMING"
mail:protocolsArray:_array_index:0:protocol = "IMAP"
mail:protocolsArray:_array_index:0:state = "RUNNING"
mail:protocolsArray:_array_index:0:error = ""
mail:protocolsArray:_array_index:1:status = "ON"
mail:protocolsArray:_array_index:1:kind = "INCOMING"
mail:protocolsArray:_array_index:1:protocol = "POP3"
mail:protocolsArray:_array_index:1:state = "RUNNING"
mail:protocolsArray:_array_index:1:error = ""
mail:protocolsArray:_array_index:2:status = "ON"
mail:protocolsArray:_array_index:2:kind = "INCOMING"
mail:protocolsArray:_array_index:2:protocol = "SMTP"
mail:protocolsArray:_array_index:2:state = "RUNNING"
mail:protocolsArray:_array_index:2:error = ""
mail:protocolsArray:_array_index:3:status = "ON"
mail:protocolsArray:_array_index:3:kind = "OUTGOING"
mail:protocolsArray:_array_index:3:protocol = "SMTP"
mail:protocolsArray:_array_index:3:state = "RUNNING"
mail:protocolsArray:_array_index:3:error = ""
mail:protocolsArray:_array_index:4:status = "OFF"
mail:protocolsArray:_array_index:4:kind = "INCOMING"
mail:protocolsArray:_array_index:4:protocol = "Junk_mail_filter"
mail:protocolsArray:_array_index:4:state = "STOPPED"
mail:protocolsArray:_array_index:4:error = ""
mail:protocolsArray:_array_index:5:status = "OFF"
mail:protocolsArray:_array_index:5:kind = "INCOMING"
mail:protocolsArray:_array_index:5:protocol = "Virus_scanner"
mail:protocolsArray:_array_index:5:state = "STOPPED"
mail:protocolsArray:_array_index:5:error = ""
mail:startedTime = "2013-01-21 21:18:32 +0000"
mail:logPaths:IMAP Log = "/Library/Logs/Mail/mailaccess.log"
mail:logPaths:Server Log = "/Library/Logs/Mail/mailaccess.log"
mail:logPaths:POP Log = "/Library/Logs/Mail/mailaccess.log"
mail:logPaths:SMTP Log = "/var/log/mail.log"
mail:logPaths:Migration Log = "/Library/Logs/MailMigration.log"
mail:logPaths:Virus Log = "/Library/Logs/Mail/clamav.log"
mail:logPaths:Amavisd Log = "/Library/Logs/Mail/amavis.log"
mail:logPaths:Virus DB Log = "/Library/Logs/Mail/freshclam.log"
mail:imapStartedTime = "2013-01-21 21:18:34 +0000"
mail:servicePortsAreRestricted = "NO"
mail:state = "RUNNING"
mail:postfixStartedTime = "2013-01-21 21:18:32 +0000"

MEGA 865 Computer doesn't boot after flashed.

my problem is .. :
Update My Mother Board Bios and dawnload a file from this site
a file is (AWFL833D.EXE W6797IMS.130 ) for update my mother board Bios
when update completed Restart a Computer ... and here a problem
my Computer doesn't boot after flashed.
i read a (How to flash the BIOS.doc) file and executing a instructions and i am fail.
when i read a (How to flash the BIOS.doc) file i found a Write:
If your system doesn't boot after you flashed, please refer to the BIOS recovery method as described.
i changed a Mother Board clear CMOS jumpers for clearing ,
and not success and the problem is until stay.
i want a solution please.
thanks.

Does your computer do or show any error mesages on the screen when rebooted. You did do this in DOS didn't you?

ASA doesn't boot after update to 8.0.4

Hi!
I've updated one of our ASA's from 8.0.3.19 to 8.0.4 and it doesn't boot into system. Step back to 8.0.3.19 also doesn't help anymore.
Enclosed is the crashdump:
Rebooting....
Processor memory 185683968, Reserved memory: 20971520 (DSOs: 0 + kernel: 20971520)
Guest RAM start: 0xd3800080
Guest RAM end: 0xdd400000
Guest RAM brk: 0xd3801000
IO memory 39403520 bytes
IO memory start: 0xd0fff000
IO memory end: 0xd3593000
Error getting l2p for anon memory 0xd4647750
Thread Name: vfw_init_thread (Old pc 0x0854297c ebp 0xd3fa7460)
Page fault: Address not mapped
vector 0x0000000e
edi 0x00019000
esi 0x00000006
ebp 0xd3fa7260
esp 0xd3fa7248
ebx 0xd4647750
edx 0x0000002d
ecx 0x00000001
eax 0x00000000
error code 0x00000006
eip 0x08966628
cs 0x00000073
eflags 0x00013246
CR2 0x00000000
Cisco Adaptive Security Appliance Software Version 8.0(4)
Compiled on Thu 07-Aug-08 20:53 by builders
Hardware: ASA5505
Crashinfo collected on 11:42:23.359 UTC Thu Aug 21 2008
Traceback:
0: 080587b3
1: 0805a4e9
2: 08965099
3: dd7a76d5
4: dd6a61e0
5: 090a0943
6: 090998e1
7: 086d7ead
8: 086d9b2d
9: 086c3f7e
10: 0864d09b
11: 0885f452
12: 08061c35
13: 08824525
14: 0886a655
15: 0805e983
Stack dump: base:0xd3fa7160 size:312, active:312
entries above '==': return PC preceded by input parameters
entries below '==': local variables followed by saved regs
'==Fn': stack frame n, contains next stack frame
'*': stack pointer at crash
For example:
0xeeeeef00: 0x005d0707 : arg3
0xeeeeeefc: 0x00000159 : arg2
0xeeeeeef8: 0x005d0722 : arg1
0xeeeeeef4: 0x005d1754 : return PC
0xeeeeeef0: 0xeeeeef20 ==F2: stack frame F2
0xeeeeeeec: 0x00def9e0 : local variable
0xeeeeeee8: 0x0187df9e : local variable or saved reg
0xeeeeeee4: 0x01191548 : local variable or saved reg
0xeeeeeee0: 0x014dde20 : local variable or saved reg
0xd3fa7640: 0x000391fc
0xd3fa7164: 0x00000280
Begin to dump crashinfo to flash....
An internal error occurred. Specifically, a programming assertion was
violated. Copy the error message exactly as it appears, and get the
output of the show version command and the contents of the configuration
file. Then call your technical support representative.
assertion "t->stack[0] == STKINIT" failed: file "thread.c", line 709
Traceback output aborted.
Flushing first exception frame:
Page fault: Address not mapped
vector 0x0000000e
edi 0x00019000
esi 0x00000006
ebp 0xd3fa7260
esp 0xd3fa7248
ebx 0xd4647750
edx 0x0000002d
ecx 0x00000001
eax 0x00000000
error code 0x00000006
eip 0x08966628
cs 0x00000073
eflags 0x00013246
CR2 0x00000000
Nested traceback attempted via signal, from:
Abort: Assert failure
vector 0x0000000e
edi 0x09b7a7f0
esi 0xd3c2a020
ebp 0xd0e6a928
esp 0xd0e6a91c
ebx 0x0000014e
edx 0x00000000
ecx 0x00000006
eax 0x00000000
error code 0x00000006
eip 0xdd6a62a1
cs 0x00000073
eflags 0x00003246
CR2 0x00000000
Cisco Adaptive Security Appliance Software Version 8.0(4)
Compiled on Thu 07-Aug-08 20:53 by builders
Hardware: ASA5505
Crashinfo collected on 11:42:31.539 UTC Thu Aug 21 2008
Traceback:
0: 080587b3
1: 08058844
2: 080588bf
3: 08964eb2
4: dd7a76d5
5: dd6a61e0
6: 080605ea
7: 08060e17
8: 0805d257
9: 0896624d
10: 0896462c
11: dd7a2a1c
12: dd74a7d7
Any ideas?
Thanks,
MB

I used another TFTP-Server and 8.0.3 Image, now I get:
Cisco Security Appliance admin loader (3.0) #0: Tue Nov 6 23:01:24 MST 2007
Loading...
â¬mount: Mounting /dev/hda1 on /mnt/disk0 failed: No such device or address
mount: Mounting /dev/hda1 on /mnt/disk0 failed: No such device or address
Doesn't sound good to me :(

Server doesn't start after applying SP3

Hi,
after applying SP3 the server doesn't start.
I just get the following error within the server log.
Any hints ?
Regards
Gerald Eder
JVMX version - May 20 2007 23:27:34 - 01_REL - optU - windows amd64 - bas2:78002 (mixed mode, sharing)
(CompilerOracle exclude com/sapportals/portal/pb/layout/taglib/ContainerTag addIviewResources)
(CompilerOracle exclude com/sap/engine/services/keystore/impl/security/CodeBasedSecurityConnector getApplicationDomain)
(CompilerOracle exclude com/sap/engine/services/rmi_p4/P4StubSkeletonGenerator generateStub)
(CompilerOracle exclude com/sapportals/portal/prt/util/StringUtils escapeToJS)
(CompilerOracle exclude com/sapportals/portal/prt/core/broker/PortalServiceItem startServices)
(CompilerOracle exclude com/sap/engine/services/webservices/server/deploy/WSConfigurationHandler downloadFile)
(CompilerOracle exclude com/sapportals/portal/prt/jndisupport/util/AbstractHierarchicalContext lookup)
(CompilerOracle exclude com/sapportals/portal/navigation/cache/CacheNavigationNode getAttributeValue)
(CompilerOracle exclude com/sapportals/portal/navigation/TopLevelNavigationiView PrintNode)
(CompilerOracle exclude com/sapportals/wcm/service/ice/wcm/ICEPropertiesCoder encode)
(CompilerOracle exclude com/sap/lcr/pers/delta/importing/ObjectLoader loadObjects)
(CompilerOracle exclude com/sap/engine/services/webservices/jaxrpc/encoding/InstanceBuilder readElement)
(CompilerOracle exclude com/sap/engine/services/webservices/jaxrpc/encoding/InstanceBuilder readSequence)
(CompilerOracle exclude com/sap/engine/services/webservices/jaxrpc/encoding/TypeMappingImpl initializeRelations)
(CompilerOracle exclude com/sap/engine/services/webservices/jaxrpc/encoding/GeneratedComplexType _loadInto)
(CompilerOracle exclude com/sap/lcr/pers/delta/importing/ObjectLoader loadObjects)
The active factory is : com.sap.engine.boot.loader.StandardClassLoaderFactory
Using an index file : D:\usr\sap\TC1\J20\j2ee\cluster\bin\index.list
[GC [ParNew: 14592K->4114K(29120K), 0.0102761 secs] 14592K->4114K(116544K), 0.0103466 secs]
Reading kernel properties from kernelProperties.bin file...
   Checked the data for 32 ms.
   Read the objects for 250 ms.
   Substituted the values for 47 ms.
Finished reading kernel objects for 297 ms.
StartupFramework returned mode [NORMAL]
StartupFramework returned action [NONE]
SAP J2EE Engine Version 7.10.3301.162847.20070927153007 is starting...
Loading: LogManager ... 578 ms.
Loading: PoolManager ... 0 ms.
Loading: ApplicationThreadManager ... Error - ID:000004. System is halted. Exception is:
java.lang.NoClassDefFoundError: com/sap/jvm/Capabilities
     at com.sap.engine.core.thread.impl3.ErrorQueueHandler.<clinit>(ErrorQueueHandler.java:34)
     at com.sap.engine.core.thread.impl3.ThreadManagerImpl.init(ThreadManagerImpl.java:204)
     at com.sap.engine.core.Framework.loadSingleManager(Framework.java:665)
     at com.sap.engine.core.Framework.loadManagers(Framework.java:367)
     at com.sap.engine.core.Framework.start(Framework.java:296)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:585)
     at com.sap.engine.boot.FrameThread.startFramework(FrameThread.java:161)
     at com.sap.engine.boot.FrameThread.run(FrameThread.java:183)
     at com.sap.engine.boot.StartFrame.work(StartFrame.java:101)
     at com.sap.engine.boot.Start.main(Start.java:33)
Caused by: java.lang.ClassNotFoundException: com.sap.jvm.Capabilities
Loader Info -
ClassLoader name: [system:Kernel]
Living status: alive
Direct parent loaders:
   [library:core_lib]
Resources:
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\jenqulib.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcantlr~runtime.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcblcachemgmtapi_for_assembly.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcblcachemgmtimpl.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcblcache_pluginslib.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcblframekrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_cacheimpl.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_classloadkrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_clusterkrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_configurationkrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_databasekrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_licensingkrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_lockingkrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_logkrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_poolkrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_servicekrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcbljkernel_threadkrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcblopensqlkernelimplOpenSQLKrn.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcjeoffline_deployimpl.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcjesessionmgmtimpl.jar
   D:\usr\sap\TC1\J20\j2ee\cluster\bin\kernel\sap.comtcseclikeylikey_assembly.jar
     at com.sap.engine.boot.loader.MultiParentClassLoader.loadClass(MultiParentClassLoader.java:259)
     at com.sap.engine.boot.loader.MultiParentClassLoader.loadClass(MultiParentClassLoader.java:228)
     at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:353)
     ... 13 more

After upgrading the SAPVM the server starts

3750x doesn't boot after upgrade to version15

Due to a problem with POE+ i have tried to upgrade the IOS to Version15.0.2SE2, from 12.2.58. unfortunatly the Switch doesn't boot up anymore. It starts to decompress and install the IOS 2 Times, after the Second try it displays "unable to boot" and the switch goes in Bootloader-mode.
When i look at the version i See that bootloader is still the old version 12.2.58.
It seems that the bootloader doesn't geht upgraded and that's why the Switch can't Boot the new Image.
Is there anything i can do to Upgrade the bootloader seperatly?
It's a 3750X48PF-S
Many thanks
Andy

This is a stack of 2 switches, both have the same problem and they are still running old image (as V15 doesn't work)
cs156005#sh license
Index 1 Feature: ipservices
        Period left: 8 weeks 4 days
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
        License Priority: None
        License Count: Non-Counted
Index 2 Feature: ipbase
        Period left: Life time
        License Type: Permanent
        License State: Active, In Use
        License Priority: Medium
        License Count: Non-Counted
Index 3 Feature: lanbase
        Period left: 0 minute 0 second
cs156005#sh inventory
NAME: "1", DESCR: "WS-C3750X-48P"
PID: WS-C3750X-48PF-S , VID: V02 , SN: FDO1527P0J8
NAME: "Switch 1 - Power Supply 0", DESCR: "FRU Power Supply"
PID: C3KX-PWR-1100WAC , VID: V02L , SN: LIT15060D4H
NAME: "Switch 1 - FRULink Slot 1 - FRULink Module", DESCR: "FRULink 10G ST Module"
PID: C3KX-NM-10G       , VID: V01 , SN: FDO14350PDY
NAME: "GigabitEthernet1/1/3", DESCR: "1000BaseLX SFP"
PID: Unspecified       , VID:      , SN: PR04004346
NAME: "2", DESCR: "WS-C3750X-48P"
PID: WS-C3750X-48PF-S , VID: V04 , SN: FDO1649P24J
NAME: "Switch 2 - Power Supply 0", DESCR: "FRU Power Supply"
PID: C3KX-PWR-1100WAC , VID: V02L , SN: LIT16371ZBN
cs156005#sh version
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 05-May-11 01:56 by prod_rel_team
ROM: Bootstrap program is C3750E boot loader
BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)
cs156005 uptime is 1 hour, 14 minutes
System returned to ROM by power-on
System restarted at 10:11:49 cet Tue Jul 9 2013
System image file is "flash:/c3750e-universalk9-mz.122-58.SE1/c3750e-universalk9-mz.122-58.SE1.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: ipbase
License Type: Permanent
Next reload license Level: ipbase
cisco WS-C3750X-48P (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1527P0J8
Last reset from power-on
2 Virtual Ethernet interfaces
1 FastEthernet interface
104 Gigabit Ethernet interfaces
4 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : A4:93:4C:95:EC:00
Motherboard assembly number     : 73-12553-05
Motherboard serial number       : FDO162001GA
Model revision number           : A0
Motherboard revision number     : D0
Model number                    : WS-C3750X-48PF-S
Daughterboard assembly number   : 800-32727-01
Daughterboard serial number     : FDO16200KPU
System serial number            : FDO1527P0J8
Top Assembly Part Number        : 800-31324-02
Top Assembly Revision Number    : E0
Version ID                      : V02
CLEI Code Number                : COMJZ00ARB
Hardware Board Revision Number : 0x03
Switch Ports Model              SW Version            SW Image
*    1 54    WS-C3750X-48P      12.2(58)SE1           C3750E-UNIVERSALK9-M
     2 54    WS-C3750X-48P      12.2(58)SE1           C3750E-UNIVERSALK9-M
Switch 02
Switch Uptime                   : 1 hour, 14 minutes
Base ethernet MAC Address       : 44:03:A7:58:AC:80
Motherboard assembly number     : 73-12553-08
Motherboard serial number       : FDO164831LB
Model revision number           : K0
Motherboard revision number     : A0
Model number                    : WS-C3750X-48PF-S
Daughterboard assembly number   : 800-32727-03
Daughterboard serial number     : FDO16491JNK
System serial number            : FDO1649P24J
Top assembly part number        : 800-31324-07
Top assembly revision number    : B0
Version ID                      : V04
CLEI Code Number                : COMJZ00ARD
License Level                   : ipbase
License Type                    : Permanent
Next reboot licensing Level     : ipbase
Configuration register is 0xF
cs156005#

Mac doesn't boot after splitting BOOTCAMP drive under Windows 8.1

Macbook pro mid 2012, OS X Mavericks
I've installed Windows 8.1 x64 using Bootcamp assistant. In Windows I went to Disk Management and shrank drive C: from 200 GB to 94 GB and created a new drive D: from unallocated space.
After restart Windows doesn't boot giving some error and quickly restart. If I hold "Option" key I see only Windows. Mac OS X disappeared.
How to fix?

So, I've tried 1001 ways to recover. Nothing worked. Interned Recovery gives -2002F error. Macbook pro 2012 can't boot from bootable DVD to use DiskWarrior, Drive Genius or similar. It can't boot from OS X Lion install DVD. I had only Windows PC to fix this. So
I asked a friend with latest Mavericks(which I had too) to make a Recovery USB and make a DMG file from it and send me over internet. Then I used the TransMac application under Windows and burned DMG on my USB stick. My god it worked. After 2 days of struggle I found this solution. I was able to boot from this USB stick into Recovery Mode and from there I can reinstall Mac Os X Mavericks. Somehow it sees my Ethernet cable and doesn't give error.
Note: that Disk Utility wasn't able to recover partitions. I tried to run DiskWarrior from terminal but it gave me an error. TestDisk didn't run too. So I'm doing a clean installation.
I could recover or backup my files using Paragon Mac Recovery Bootable DVD, but there was no need since it's my new macbook and I didn't have much files there.
Windows had changed the HD partition map from GUID Partition Table(GPD) to MBR. And made HD a "dynamic disk". This is why Mac Os wasn't able to boot.
If anyone knows how to convert a disk back to GPD and make Mac OS able to boot please let me know. I'm still installing Mac Os X on USB stick and didn't change my HD.

BEA WebLogic 8.1 server not booting after adding a security realm

Hi,
I have added my own security realm for BEA WebLogic Server 8.1.
However, when I try to boot the server using this realm, it simply hangs. I cannot
take thread dumps as the server java process does not respond to "kill -3 PID"
(after the server has hung).
When I looked at the server log file, I observed that the server had hung after
initializing the IIOP subsystem.
I have attached herewith the following 3 files:
1. config.xml (the server config file after adding entry for my security realm)
2. default_realm.log (the server log file when booted through the default realm)
3. netpoint_realm.log (the server log file when booted through my realm).
Is there any way, I can debug where the server is exactly hanging?
Thanks and Regards,
Abhinay
[BEA_Files.zip]

is it admin server or Managed server which isnot starting?
Mir

MDM Server doesn't start after upgrade to SP 5

hi,
i'm not used to sap services on windows hosts.
After the Update from 7.1.04 to 7.1.05 the mdm server doesn't start. I found only a few logs (unter c:/usr/sap/SID/MDS00/work). Most of them from sapcpe (without errors or warnings). Only the sapstart.log contains a bit information:
SAP-R/3-Startup Program
Starting at 2010/08/16 21:29:18
Startup Profile: "C:\usr\sap\MDM\SYS\profile\MDM_MDS00_mdmtest"
Starting Programs
(1684) Execute: C:\usr\sap\MDM\SYS\exe\uc\NTAMD64\sapcpe.EXE pf=C:\usr\sap\MDM\SYS\profile\MDM_MDS00_mdmtest list:C:\usr\sap\MDM\SYS\exe\uc\NTAMD64/mds.lst
(976) Execute: C:\usr\sap\MDM\SYS\exe\uc\NTAMD64\sapcpe.EXE pf=C:\usr\sap\MDM\SYS\profile\MDM_MDS00_mdmtest list:C:\usr\sap\MDM\SYS\exe\uc\NTAMD64/shared.lst
(3632) Execute: C:\usr\sap\MDM\SYS\exe\uc\NTAMD64\sapcpe.EXE pf=C:\usr\sap\MDM\SYS\profile\MDM_MDS00_mdmtest list:C:\usr\sap\MDM\SYS\exe\uc\NTAMD64/sapinstance.lst
(2172) Execute: C:\usr\sap\MDM\MDS00\exe\mdmcpc.bat C:\usr\sap\MDM\SYS\profile\MDM_MDS00_mdmtest.INI C:\usr\sap\MDM\MDS00\config\mds.ini
(3652) CreateProcess: C:\usr\sap\MDM\MDS00\exe\mds.EXE
Process 3652 died unexpectedly, restarting process
(3612) Restart CreateProcess: C:\usr\sap\MDM\MDS00\exe\mds.EXE
Process 3612 died unexpectedly, restarting process
(2364) Restart CreateProcess: C:\usr\sap\MDM\MDS00\exe\mds.EXE
Process 2364 died unexpectedly, restarting process
(3576) Restart CreateProcess: C:\usr\sap\MDM\MDS00\exe\mds.EXE
Process 3576 died unexpectedly, restarting process
(3588) Restart CreateProcess: C:\usr\sap\MDM\MDS00\exe\mds.EXE
Process 3588 died unexpectedly, final process restart.
Process will not be restated in the future because of frequent failure.
(1396) Restart CreateProcess: C:\usr\sap\MDM\MDS00\exe\mds.EXE
This isn't really much I can work with. In the sapmmc I found the Option Developer Trace. I try to 'switch it on', but there is no difference.
With 7.1.04 the server was running well.
I happy for any suggestions

Hi,
Please check out Note 1482822 - MDM Server not starting after MDM 7.1 SP05 was installed.
hope it helps you.
Best regards,
sudhanshu

Cisco UCS C220-M3 Server doesn't boot after adding Intel I350 Quad Port NIC

Similar Messages

Maybe you are looking for