Cisco Unified CM Administration is not working in RDP sessions .

Dear all.,
Cisco unified cm administration we are working in sandbox labs connected through vpn of Cisco. But we are not able to access through remote desktop sessions. is it any possible to access through remote desktp sessions..?

Hi
We are getting Cisco Unified CM Administration using sandbox labs. we are having a product for telecommunication . The name is CADEBILL. we are implementing the process from that product. we installed that product in a server. We have VPN through that sandboxlabs. That vpn is installed in local pc. From that local pc we will access the server in Remote desktop . in that server we are not able to install the anyconnect vpn . So this problem.
This is cisco unified CM version. System version: 8.6.1.20000-1

Similar Messages

Is there any option on Cisco Unified CM Administration 9.1.1 to show caller ID number when using MOBILITY option?

Dear All,
I am using Cisco Unified CM Administration 9.1.1 and MOBILITY works fine.
However when somebody calls from external phone number into internal user number and MOBILITY option is ON and obviously, forwards the call for the user's cell.....in this case user can see only main company number, but not a caller number.
So, is there any option to change it?
Thank you

Go to the GW and run some debugs to find out exactly what you're sending, chances are, your telco is overwriting the original called number as it's nor part of your DID range.
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk

UCCX cannot open the "Cisco Unified OS Administration" system

Hi,
When I select "Cisco Unified OS Administration" and click "Go", the system shows below error messages.
Navigation:
Cisco Unified CCX Administration (Can open this webpage)
Cisco Unified CCX Serviceability    (Can open this webpage)
Cisco Desktop Administrator         (Can open this webpage)
Cisco Unified Serviceability           (Can open this webpage)
Cisco Unified OS Administration   (Cannot open, it shows error page)
Disaster Recovery System           (Can open this webpage)
What is the problem?
Please help, thanks.
HTTP Status 500 -
type: Exception report
message:
description: The server encountered an internal error () that prevented it from fulfilling this request.
exception:
org.apache.jasper.JasperException: java.lang.NullPointerException
     org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper.java:418)
     org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:342)
     org.apache.jasper.servlet.JspServlet.service(JspServlet.java:267)
     javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
     sun.reflect.GeneratedMethodAccessor228.invoke(Unknown Source)
     sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     java.lang.reflect.Method.invoke(Method.java:597)
     org.apache.catalina.security.SecurityUtil$1.run(SecurityUtil.java:269)
     java.security.AccessController.doPrivileged(Native Method)
     javax.security.auth.Subject.doAsPrivileged(Subject.java:517)
     org.apache.catalina.security.SecurityUtil.execute(SecurityUtil.java:301)
     org.apache.catalina.security.SecurityUtil.doAsPrivilege(SecurityUtil.java:162)
root cause:
java.lang.NullPointerException
     org.apache.struts.taglib.TagUtils.computeURLWithCharEncoding(TagUtils.java:428)
     org.apache.struts.taglib.TagUtils.computeURLWithCharEncoding(TagUtils.java:311)
     org.apache.struts.taglib.logic.RedirectTag.generateRedirectURL(RedirectTag.java:294)
     org.apache.struts.taglib.logic.RedirectTag.doEndTag(RedirectTag.java:268)
     org.apache.jsp.index_jsp._jspx_meth_logic_005fredirect_005f0(index_jsp.java:89)
     org.apache.jsp.index_jsp._jspService(index_jsp.java:64)
     org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:70)
     javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
     org.apache.jasper.servlet.JspServletWrapper.service(JspServletWrapper.java:374)
     org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:342)
     org.apache.jasper.servlet.JspServlet.service(JspServlet.java:267)
     javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
     sun.reflect.GeneratedMethodAccessor228.invoke(Unknown Source)
     sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     java.lang.reflect.Method.invoke(Method.java:597)
     org.apache.catalina.security.SecurityUtil$1.run(SecurityUtil.java:269)
     java.security.AccessController.doPrivileged(Native Method)
     javax.security.auth.Subject.doAsPrivileged(Subject.java:517)
     org.apache.catalina.security.SecurityUtil.execute(SecurityUtil.java:301)
     org.apache.catalina.security.SecurityUtil.doAsPrivilege(SecurityUtil.java:162)
note: The full stack trace of the root cause is available in the logs.

Hi,
After reinstalling the UCCX system, everything is ok.
Thanks for your help.

Cisco Unified OS Administration Login

I am wondering if it is possible to change how to login to Cisco Unified OS Administration and Disaster Recovery System via the Web front end of Call Manager 6.1.3. Currently you need to login as Administrator to those 2 Web pages, but for Cisco Unified CM Administration, Serviceability, and Reporting you do not. I can login with my Call Manager account. It would be a lot easier if my and the other administrator could just use are Call Manager login for those 2 pages instead of the Administrator account. Is this possible?

No, OS admin and DRS systems are separate from Admin pages.
You need to authenticate to each one because of what privileges each one provides within the system and at which level they're.
HTH
java
if this helps, please rate

Cannot reset user vmail password with Cisco Unified CM Administration

We are using Cisco Unified CM Administration ver 7.1 with Cisco 7945 IP phones. I have a user who came to me saying that they could no longer access voice mail, getting invalid pin. Ichanged the pin with the Cisco Unified CM Administration which accepts the new pin no problem but when we try it from the phone it doesn't work. Any ideas... Thanks Don

Hey Don,
Well, that's no good
There should be no correlation between resetting the user PIN
and the forwarding to voicemail.
Let's say that the user is @ DN/extension 5999.
In CUCM admin go to;
Device>Phone>Find List by Directory number> find 5999
on the DN config page look at the Call Forward sections (all, no answer, busy)
and make sure they are set to forward to VM (usually by using the VM checkbox)
If you need to, have a look at a working phone/DN for comparison
Cheers!
Rob
"Spend your life waiting,
for a moment that just don't come,
Well, don't waste your time waiting"
-Springsteen

Tool(s) in Cisco Unified CM Administration to support Identity Management (IDM)?

Hi,
In our "Cisco Unified CM Administration System version: 7.0.1.11000-2" installation, I can manually create and administrate users information.
But we do also have an identity Management (IDM) system in house, that creates users in Microsoft 2003 Active Directory and some sub-systems with the necessary rights they need.
It would be a lot easier, if our IDM system could create the user in our “Cisco Unified CM Administration System version: 7.0.1.11000-2" when they are created in the MS Active Directory, with the right username, first name, last name, department name and so forth.
Is there any tool that I can use to make this automatic import of user information?
Kind regards,
Carl-Marius

There are couple solutions.
You may integration CUCM with LDAP. Whenever you have a user created in LDAP, CUCM will synchronize that user into CUCM user database. Then you may assign different permissions for different LDAP users.
If you don't want to do LDAP integration, you may also consider using AXL to create users in CM database. AXL is an interface for 3rd-party software to read/write database.
Michael
http://htluo.blogspot.com

Cisco Unified CM Administration ver 7.1 date and time issue

We are using Cisco Unified CM Administration ver 7.1. I think this will be an easy one. I've done it before and need to do it again. Is there an easy way to adjust the time that appears on all our Cisco 7945 phones. It is out by a dozen of minutes... Thanks Don

The latest release of CUCM 7.1.5 is 7.1.5.35901-1, so you can always try that. Link to download:
http://software.cisco.com/download/release.html?mdfid=282421166&flowid=45895&softwareid=282074295&release=7.1(5b)SU6a&relind=AVAILABLE&rellifecycle=&reltype=latest
The latest version of CUCM software is 9.1.2 with 10.0 coming out any day, thought those would be considered major upgrades and would require some planning, on i.e. ensure hardware compatibility, all software compatibilities, ELM licensing migration, etc.
HTH,
Chris

How do I remove the certificat error everytime I try to access the Cisco Unified CM Administration web-page?

Hi,
Every time I want to have access to the Cisco Unified CM Console (System version: 7.0.1.11000-2), I use the https://10.10.x.x/ccmadmin/showHome.do homepage on my client computer, but when I open the page, I get a SSL certificate error, stating no trust to this webpage security certificate and if I those "continue to this page (not recommended)", I get access to the Cisco Unified CM Console web page.
I have tried to add the https://IP-adress to secure web pages in Internet Explorer 7, but this to no avail, it does not help.
How do I add this certificate to a trusted something, so I do not get this warning every time I open the page?
Kind regards,
Carl-Marius

Hi Michael,
It worked when I change the IP-address to the name that was written in the certificate, and imported the certificate to Internet Explorer.
Thank you for your fast and very precise help!
Kind regards,
Carl-Marius

Cisco css http keepalive is not working with GET command

Dear all
i have Cisco Css connected to Dell Server (via switch)
Cisco CSS - 192.168.1.3 and Dell Server - 192.168.1.5
Dell server is setup with windows 2009R2 and Apache HTTPD is version 2.2
This server is dedicated to host multiple doamins with Apache lik
www.abc.co.uk
www.xyz.co.uk
Now the clinet wants to setup the http keepalive with specfic web page like /testpage.html for all these domains. i have teseed with single URI. it is working the comamnds are
config)# service serv1
(config-service[serv1])# ip address 192.168.1.5
(config-service[serv1])# keepalive type http
(config-service[serv1])# keepalive method head    ( get i have not used due to hash mismatch with apche server, if i use GET it is not working)
(config-service[serv1])# keepalive uri "/testpage.html"
(config-service[serv1])# active
It is working with single URI. but how can i do the same thing for multiple doamins ?
for multiple doamins do i need use script ? or can i use with commands ?
if i need to use script the script is
!no echo
! Filename: httptag-test
! Parameters: HostName WebPage HostTag
! Description:
!       This script will connect to the remote host and do an HTTP
!   GET method upon the web page that the user has asked for.
!   This script also adds a host tag to the GET request.
! Failure Upon:
!   1. Not establishing a connection with the host.
!       2. Not receiving an HTTP status "200 OK"
if ${ARGS}[#] "NEQ" "3"
        echo "Usage: httptag-test \'Hostname WebPage HostTag\'"
        exit script 1
endbranch
! Defines:
set HostName "${ARGS}[1]"
set WebPage "${ARGS}[2]"
set HostTag "${ARGS}[3]"
! Connect to the remote Host
set EXIT_MSG "Connection Failure"
socket connect host ${HostName} port 80 tcp
! Send the GET request for the web page
set EXIT_MSG "Send: Failed"
socket send ${SOCKET} "GET ${WebPage} HTTP/1.1\nHost: ${HostTag}\n\n"
! Send the HEAD request for the web page
set EXIT_MSG "Send: Failed"
socket send ${SOCKET} "HEAD ${WebPage} HTTP/1.1\nHost: ${HostTag}\n\n"
! Wait for a good status code
set EXIT_MSG "Waitfor: Failed"
socket waitfor ${SOCKET} "200 OK"
no set EXIT_MSG
socket disconnect ${SOCKET}sh w
exit script 0
in the script i have not used GET becasue, when CSS send GET request to apache it use hash, but apache is not able to respond with same hash and it shows that website is down. more information- click below url
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/css11500series/v7.40/command/reference/CmdKeepC.html#wp1139668
(config-keepalive) method
I have uploaded in CSS with httptag-test file and applied these commands
service comp.brit.co.uk-80
keepalive port 80
ip address 192.168.1.5
keepalive frequency 10
keepalive maxfailure 2
keepalive retryperiod 10
keepalive type script httptag-test "192.168.1.5 /testpage.html www.abc.co.uk
keepalive type script httptag-test "192.168.1.5 /testpage.html www.xyz.co.uk
but this script is not working
my question is:
1.do i need use script only to setup http keepalvie with webpage for multiple domains ?
2.with out using script is there any solution like CICSCO CSS commands to setup http uril for multiple domains which are on 1 singl server.
please help me asap

Hello Muhammad,
If you wish to use multiple domains for a URI keep-alive check, and perform a HEAD request what Daniel mentioned is correct. You have to use a scripted keep-alive check on the service. However, you should not use the default "ap-kal-httptag" script to do so as it's limited to only 1 website (unless you modify the script). You're best bet would be using the "ap-kal-httplist" script on the CSS as it allows the checking of 2 different websites along with a webpage to check for each site using HTTP HEAD method.
!no echo
! Filename: ap-kal-httplist
! Parameters: Site1 WebPage1 Site2 WebPage2 [...]
! Description:
!    This script will connect a list of sites/webpage pairs. The
!   user must simply supply the site, and then the webpage and
!   we'll attempt to do an HTTP HEAD on that page.
! Failure Upon:
!   1. Not establishing a connection with the host.
!   2. Not receiving a status code 200 on the HEAD request on any
!      one site. If one fails, the script fails.
! Make sure the user has a qualified number of arguments
if ${ARGS}[#] "LT" "2"
        echo "Usage: ap-kal-httplist \'WebSite1 WebPage1 WebSite2 WebPage2 ...'"
        exit script 1
endbranch
while ${ARGS}[#] "GT" "0"
        set Site "${ARGS}[1]"
    var-shift ARGS
    if ${ARGS}[#] "==" "0"
        set EXIT_MSG "Parameter mismatch: hostname present but webpage was not"
        exit script 1
    endbranch
    set Page "${ARGS}[1]"
    var-shift ARGS
    no set EXIT_MSG
    function HeadUrl call "${Site} ${Page}"
endbranch
exit script 0
function HeadUrl begin
! Connect to the remote Host
set EXIT_MSG "Connect: Failed to connect to ${ARGS}[1]"
socket connect host ${ARGS}[1] port 80 tcp 2000
! Send the head request
set EXIT_MSG "Send: Failed to send to ${ARGS}[1]"
socket send ${SOCKET} "HEAD ${ARGS}[2] HTTP/1.0\n\n"
! Wait for the status code 200 to be given to us
set EXIT_MSG "Waitfor: Failed to wait for '200' on ${ARGS}[1]"
socket waitfor ${SOCKET} " 200 " 2000
no set EXIT_MSG
socket disconnect ${SOCKET}
function HeadUrl end
Rather then modify the default "ap-kal-httplist" script on the CSS I would simply define the arguments within the service configuration itself.   Something like the following (using your service example):
service dell-192.168.1.5
ip address 192.168.1.5
keepalive type script ap-kal-httplist "www.abc.co.uk /testpage.html www.xyz.co.uk /testpage.html"
active
As long as the server is configured to reply to host headers, and the page is configured to retuen a "200 OK" the above service configuration should work. If there are any errors simply run "show service " to view why there was a failure. If there is a failure, and the output from the command specified shows a line number run the following command against the script to view at what point (line) did the failure occur:
show script ap-kal-httplist line-numbers
Hope this helps!
- Jason Espino

Cisco Ise Central Web authentication not working

Hello Guys,
CWA is not working. It says that authentication suceeded but posture status is pending. No error in my Monitor--authentication. Checking it in my Windows 7, it does not shows the CWA portal.
What might be the possible problem of this.?
thanks

Kindly review the below links:
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080ba6514.shtml
http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml

BIOS Administrator Password Not Working

I just set the BIOS admin password yesterday and today it's not working. What are my options for resetting it?

Logon the computer and use the internal structure to set a password.
Should be via Control Panel, Users.
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

P1102 will not work as RDP printer

P1102 will not print as redirected printer on Windows Server R2 Standard SP1 X64 terminal server.
We have downloaded latest 2008 x64 driver but will not work.
P1102 local network printers will print from network but not as RDP printers from the same terminal.
Tried to instal the P1102 on the actual Server itself but it will not instal as a USB printer on the server?

You have a lot of learning to do. The overlap between interactive PDF and
DPS is not all that great. Start with the DPS help here on Adobe.com and
download Bob Bringhurst's DPS Tips app in the app store.

DBLINK not working in restricted session.

Hi
All,
I have just upgraded database from 9.2.0.6 to 10.2.0.3. everything was working before upgradation but after upgradation DBLINK not working in restricted sesion.
it has all the restricted session privilage. and also like after upgradation it is working without restricted session. when I put in restricted session it's not working .it was working under restricted session in 9.2.0.6.
Thanks,
Vishal

From 9.2.0.6 to 10.2.0.3 there is some difference in the privileges granted to the roles. So you need to be aware of the new features before you upgrade.
For instance, in 10g, the CONNECT role only has the CREATE SESSION privilege and has been striped off the following privileges:
CREATE CLUSTER
CREATE DATABASE LINK
CREATE SEQUENCE
ALTER SESSION
CREATE SYNONYM
CREATE TABLE
CREATE VIEW
So, if your DBLINK user had these privileges via the CONNECT role, you need to grant them the privileges again to be able to carry out any related tasks. it may not just be because of the restricted session.

Cisco AIR-LAP1041N-E-K9 not working with WLC 4402 version 7.0.116.0

Hi All,
appreciate your support for a problem i started facing today. i have a Cisco WLC 4402 running version 7.0.116.0 and it is working great with 25 Cisco 1252 APs. we have recieved a new 20 Cisco 1041N APs today and i installed one in our site but it doesn't work. it worked fine and loaded the image from flash and got the WLC ip address through DHCP option and started showing the below error:
*Mar 1 00:00:10.021: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:10.033: *** CRASH_LOG = YES
*Mar 1 00:00:10.333: Port 1 is not presentSecurity Core found.
Base Ethernet MAC address: C8:9C:1D:53:57:5E
*Mar 1 00:00:11.373: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:11.465: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1088 messages)
*Mar 1 00:00:11.494: status of voice_diag_test from WLC is false
*Mar 1 00:00:12.526: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.594: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.647: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 12:50 by prod_rel_team
*Mar 1 00:00:13.647: %SNMP-5-COLDSTART: SNMP agent on host APc89c.1d53.575e is undergoing a cold start
*Mar 1 00:08:59.062: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:08:59.062: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:08:59.138: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:08:59.837: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:09:00.145: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:09:09.136: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.16.26.81, mask 255.255.255.0, hostname APc89c.1d53.575e
*Mar 1 00:09:17.912: %PARSER-4-BADCFG: Unexpected end of configuration file.
*Mar 1 00:09:17.912: status of voice_diag_test from WLC is false
*Mar 1 00:09:17.984: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:09:19.865: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:09:19.886: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:09:20.873: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:09:20.874: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
Translating "CISCO-CAPWAP-CONTROLLER.atheertele.com"...domain server (172.16.40.240)
*Mar 1 00:09:29.029: %CAPWAP-5-DHCP_OPTION_43: Controller address 172.16.100.102 obtained through DHCP
*May 25 08:27:02.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:02.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:03.175: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:03.177: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:03.177: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:03.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:03.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:03.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:03.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:03.378: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:03.448: status of voice_diag_test from WLC is false
*May 25 08:27:14.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:14.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:15.185: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:15.186: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:15.186: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:15.330: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:15.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:15.334: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:15.334: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:15.379: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:15.450: status of voice_diag_test from WLC is false
*May 25 08:27:26.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:26.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:27.182: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:27.183: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:27.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:27.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:27.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:27.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:27.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:27.377: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:27.433: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*May 25 08:27:27.446: %PARSER-4-BADCFG: Unexpected end of configuration file.
*May 25 08:27:27.447: status of voice_diag_test from WLC is false
*May 25 08:27:27.448: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*May 25 08:27:27.456: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*May 25 08:27:38.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:38.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:39.183: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:39.184: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:39.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:39.326: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:39.329: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:39.329: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:39.330: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:39.375: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:39.446: status of voice_diag_test from WLC is false
*May 25 08:27:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:49.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:50.179: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:50.180: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:50.180: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:50.323: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:50.326: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:50.326: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:50.326: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:50.370: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:50.425: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*May 25 08:27:50.438: %PARSER-4-BADCFG: Unexpected end of configuration file.
i searched for the regulatory domains difference between AIR-LAP1041N-E-K9 and AIR-LAP1041N-A-K9 and didn't find any difference that may affect the operation of this AP.
just to mention that our configuration in WLC for regulatory domains is:
Configured Country Code(s) AR
Regulatory Domain 802.11a: -A
802.11bg: -A
My question is, should i only include my country in the WLC (IQ) to add the requlatry domain (-E) to solve this problem? or changing the country will affect the operation of all working APs??
Appreciate your kind support,
Wisam Q.

Hi Ramon,
thank you for the reply but as shown in the below link:
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7.0.html#wp233793
the WLC in version 7.0.116.0 supports Cisco 1040 seiries APs.
Thanks,
Wisam Q.

CUCI-Lync 9.2 with CUCM 8.6 - Cisco Unity Connection Visual Voicemail Not Working

Hi
I have CUCM and CUC 8.6.2 running and MOC with CUCI-Lync 8.5 (with visual Voicemail) running OK with full registry configuration (see below). We are moving to Lync 2013 and want to use CUCI-Lync 9.2.
A basic install of CUCI-Lync 9.2 works fine with CUCM (with manual setup of TFTP, CCMIP and CTI) but not with CUC. I can only call the VM Pilot but I don't get my visual voicemail. In the CUCI-Lync parameters I type in my CUC server IP adress and credentials but get a message saying that it can't connect.
As the config guide describes a config with CUCM 9 (with UC services) which I don't have in V8.6. I've tried using the old registry configuration or no registry configuration at all, I can't get CUCI-Lync to connect to CUC...
Has anyone done this ? Any suggestions ?
OLD REG Configuration:
Windows Registry Editor Version 5.00
[HKEY_CURRENT_USER\Software\Cisco Systems, Inc.\Unified Communications\CUCIMOC]
"RememberMe"=dword:00000001
"AutoLogin"=dword:00000001
[HKEY_CURRENT_USER\Software\Cisco Systems, Inc.\Client Services Framework\AdminData]
"TftpServer1"="1.1.1.1"
"TftpServer2"="2.2.2.2"
"TftpServer3"=""
"UseCUCMGroupForCti"="1"
"CcmcipServer1"="1.1.1.1"
"CcmcipServer2"="2.2.2.2"
"CcmcipServerValidation"="0"
"CsfStatsServer"=""
"CsfStatsCollectionEnabled"=""
"EnableNativeDirectoryProvider"="1"
"VoicemailPilotNumber"="12345"
"VoiceMailService_UseCredentialsFrom"="PHONE"
"VVM_SystemServer_0"="3.3.3.3"
"VVM_SystemServer_1"="4.4.4.4"
"VVM_SystemServer_VmwsProtocol_0"="HTTP"
"VVM_SystemServer_VmwsProtocol_1"="HTTP"
"VVM_SystemServer_VmwsPort_0"="80"
"VVM_SystemServer_VmwsPort_1"="80"
"VVM_Mailstore_Server_0"="3.3.3.3"
"VVM_Mailstore_Server_1"="4.4.4.4"
"VVM_Mailstore_ImapProtocol_0"=""
"VVM_Mailstore_ImapProtocol_1"=""
"VVM_Mailstore_ImapPort_0"="143"
"VVM_Mailstore_ImapPort_1"="143"
"VVM_Mailstore_InboxFolderName"=""
"VVM_Mailstore_EncryptedConnection"=""
"VVM_Mailstore_PollingInterval"=""
"AutomaticDeviceSelectionMode"="0"
"SSO_Enabled_CUCM"="false"
"DeviceProviderServer1"="1.1.1.1"
"DeviceProviderServer2"="2.2.2.2"
"DeviceProviderServerValidation"="0"
"DeviceProviderType"="CCMIP"

The UC Services are a CUCM 9.0 feature. In 8.x these existed within CUPS under Applications > CUPC/Jabber > CTI Gateway and Profile. Other things that frequently cause this to break: 1) deskphone not associated to your end user object; 2) primary extension not set; 3) standard cti enabled and standard ccm end users group membership missing; 4) the IP/FQDN of the CTI Gateway is not a CUCM node running CTI Manager.
Please remember to rate helpful responses and identify helpful or correct answers.

Cisco Unified CM Administration is not working in RDP sessions .

Similar Messages

Maybe you are looking for