Cisco View Device Manager

Hi,
is there anybody who can tell me how to bring the Cisco View Device manager for 6500er up? I've installed the CVDM V.1.1 in the bootflash of my 6500er, IOS version is 12.2(18)SXF4 enterprise services. Installed java on the client is v.1.4.2_06. After launching the CVDM whithout proxy settings the windows starts gathering information, after a few seconds it stops with an error "java.lang.NullPointerException". This failure appeared with Mozilla 2.0.0.8 and IE 6.0, on the 6500er all vty lines are idle. Is anybody here who can help to solve the problem?

Here the text from the readme file; try to get the zip-file via the Bug-Id:
09-December-2005
This patch provides fix for the following bug:
CSCsc10956 - CVDM 1.1 does not work with 12.2(18)SXF
SUPPORTED IOS VERSION:
12.2(18)SXF
SIZE:
5,593,057 Bytes
DOWNLOADING AND MOVING FILES TO TFTP SERVER:
cvdm-c6500-1.1-CSCsc10956.zip contains the following two files
* cvdm-c6500-1.1.tar and
* cvdm-c6500-1.1_K9.tar (for Cisco IOS Cryptographic software)
Unzip cvdm-c6500-1.1-CSCsc10956.zip and copy one of the tar files to a TFTP server
Make sure to enter filenames exactly as they appear; (filenames are case-sensitive).
TRANSFERRING FILES TO YOUR SWITCH:
Step 1 : Access the switch CLI using a Telnet connection or the console port.
Step 2 : Transfer the files from the TFTP server to the bootflash of the switch. Issue
the following command:
# archive tar /xtract tftp:// / bootflash:
where is the filename of the CVDM-C6500 tar file you want to install
and is the IP address of the TFTP server. Make sure to enter filenames
exactly as they appear (filenames are case-sensitive). Make sure you are not in
configuration mode when issuing the archive command.
Step 3 : If you are not in configuration mode, issue the following command:
# configure terminal
Step 4 : Set HTTP server and path. For example:
# ip http path bootflash:
Please refer cvdm-c6500-1_1_readme.pdf in http://www.cisco.com/cgi-bin/tablebuild.pl/cvdm-6k for
further details on CVDM-C6500.

Similar Messages

Cisco PIX Device Manager Version 3.0(2)

Hi
I have a PIX 515E:
Cisco PIX Firewall Version 6.3(4)
Cisco PIX Device Manager Version 3.0(2)
Compiled on Fri 02-Jul-04 00:07 by morlee
CCP-Firewall001 up 2 years 65 days
Hardware: PIX-515E, 32 MB RAM, CPU Pentium II 433 MHz
Flash E28F128J3 @ 0x300, 16MB
BIOS Flash AM29F400B @ 0xfffd8000, 32KB
0: ethernet0: address is 0012.80be.450d, irq 10
1: ethernet1: address is 0012.80be.450e, irq 11
Licensed Features:
Failover: Disabled
VPN-DES: Enabled
VPN-3DES-AES: Disabled
Maximum Physical Interfaces: 3
Maximum Interfaces: 5
Cut-through Proxy: Enabled
Guards: Enabled
URL-filtering: Enabled
Inside Hosts: Unlimited
<--- More ---> Throughput: Unlimited
IKE peers: Unlimited
This PIX has a Restricted (R) license.
Serial Number: 808480455 (0x30306ec7)
Running Activation Key: 0xac646fed 0xf8b86795 0xc3951ec2 0xb32aed09
It's operate with Java plug in 1.4.1 y I have a PC with IE 7 and Plug in 1.6.0 y doesn't download the PDM.
Are there a solution for it?

Try Disable Java on Internet Options. This issue oculd be releated to Java version also.

Windows 7 64-bit Cisco Fabric/Device Manager Installer

Does anyone know if there is Cisco Device Manager Installer compatible with Windows 7 (64-bit)? I'm trying to install Device Manager onto my Windows 7 PC. this may happen on my Fabricv Manager Installer, as well. Any help would be appreciated.
Thanks

Senthil, Horacio,
I would not recommend using a 8.5(x) client against a 8.0(x) server (the OP suggests UCCE 8.0 is used). Even though they _should_ be compatible, they usually are not.
Upgrading the server side to 8.5 is the way to go IMHO.
G.

Does Cisco Fabric/Device Manager 5.0(4d) run under VM?

I'd like to upgrade the OS on our W2k3 to W2K8 64-bit via virtual machine. First, is it possible to run Cisco Fabric and Device Manager under VM 2K8 64-bit? Has there been any issues reported running these tools, on VM?
Thanks

Hello Jayson,
Yes, Cisco Fabric Manager and Nevice Managercan run on W2k3 to W2K8 64-bit VM
http://www.cisco.com/en/US/partner/docs/switches/datacenter/mds9000/sw/5_0/release/notes/fm/fm_rel_notes_504d.html
VMs:
VMs that run any qualified or supported operating system version can run Cisco Fabric Manager.
Thanks

SW download: unable to download Cisco View device packages and CVW patches

With the current Software Download frontend I cannot find a way to download ciscoview device packages and software patches; I can get these files through the "Software Search" feature but that's hardly what I need. To update a LMS server that is not allowed to connect to the internet it is necessary to have the option to download these device packages and patches in a bulk....
just tell me where to click.... :-)

Hi Martin,
Is this better? http://www.cisco.com/cgi-bin/tablebuild.pl/cview50

Uploading/Installing procedure for device packages in Cisco View/RME

Hi,
Running LMS3.2 with HUM 1.2.
In cisco view when we tried for below mwntioned devices it says "Device Package for these device is not available".
WS-C2960S
CISCO2921
CISCO3945E.
Please let me know the link to download the device packages for above devices and the procedure to install it on LMS.
Thanks & Regards,
Krishna

Hi Krishna,
Replace the attached file (vds.properties) in the below location :
NMSROOT\CSCOpx\lib\classpath\com\cisco\nm\xms\vds
then Restart the Daemon Manager ..
NOTE : Please take the Bcakup of your Existing file (vds.properties)
--Then go to common service > software center > device update >> check for the Device Pcakages , you will be able to see the Device Packages now..
Thanks--
Afroj
If this post answers your question, please click the "Correct Answer" button"

Unable to open 2 9509 switches at the same time in Cisco Device Manager

Dear Friends,
There are a pair of MDS 9509 switches whose management addresses are 172.16.2.197 and 172.16.2.198.
When we try to manage these Devices through Cisco device manager, the first device opens up without any problem, but when the second 9509 is opened in Cisco Device Manager, it fails giving the following error message:
"Open udp transport failed: Address already in use: Cannot bind"
To get around this issue, if we close the first interface to the 9509 switch, then we are able to open up the second 9509 in Device Manager.
We have this problem only in Cisco device manager. If we open one switch in Cisco device manager and the other switch in Cisco Fabric Manager, it works.
Also, we can telnet to both the devices successfully at a time.
The device manager in use is 4.1.
Please find enclosed the sh version outputs for your kind reference.
Can you please help me understand the cause of this issue?
Thanks a lot
Gautam

Is it always the same MDS that fails to open, or can you open either one first, and then the second one poses the problem (no matter which one is second)?
Can you try from a second work station and see if you can open DM to both switched at the same time? I suspect the address it is complaining about is the local workstation IP, not the MDS IP.
If you open the FM map, then you click on the MDS ICONs, can you open DM to both MDS?
- Mike

Cisco Prime Infrastructure - I can't see the hardware virtual image when I selected a device managed by Prime Infrastructure. See attached picture

My Cisco Prime Infrastructure ver. 1.2.1.12
Cisco Prime Infrastructure - I can't see the hardware virtual image when I selected a device managed by Prime Infrastructure. See attached picture.
Please let me know how to access or enable the feature.
Thanks,
Tek

This is by no means a full solution, but deleting and re-adding only takes a few minutes if you use the "Export Device" and "Bulk Import" features from the Device Work Center. You can export the desired devices to a CSV file, delete them, then import from the CSV.
Of course, you might lose historical data when deleting the devices, but I'm guessing that's not as relevant since the devices themselves have been replaced by different hardware.

Quick Question about Cisco 3560 and the Web Device Manager

Alright, I have a quick question that I am curious about but I haven't found any information
about it.
When I log into my Cisco 3560 using the web portal to get to the Device Manager. Below the
diagram of the switch, then under the Dashboard there is section called Switch
Health, Port Utilization.
Under the Switch Health there is Bandwidth Used, Packet Error. Those two options just sit
at zero and do not move. The Port tilization graph is also sitting at zero.
Is there a way to make them functional?

Anyone notice performance increase or decrease of their HD when using the nVidia IDE SW drivers? particularly with a 74GB Raptor? I've also heard of burner issues when installing the IDE SW but have not used my burner yet.

View-only access to Catalyst 2960/2960S device manager

I have noticed that when I access the (Web-based) device manager on a Catalyst 2960 or 2960S switch, the authentication prompt (from within IE, at least) includes the phrase, "The server <switch-hostname> at level_15_or_view_access requires a username and password." This would seem to imply that it's possible to configure view-only (a.k.a. read-only) access to the device manager, which would be perfect for first-level support personnel (in our environment). I reviewed the information on how to configure local authentication for the Web server (leveraging "ip http authentication local" among other commands), but the examples are a bit too broad for me understand how to specifically (and only) allow someone coming in via HTTP(S) to gain read-only access to the device manager. (Command line access should be denied entirely for the view-only user, if possible, or at least limited to commands that can't modify the switch's configuration.) Assuming this is possible, could someone cite the command sequence required?
Thanks,
Mike

Hi,a customer want a user which has view-only rights on his catalyst switches. I created a user whit privilige level 7.If you log into the CLI everything is fine. But by trying to log into the web page the system wants a level 15 user.Is their any possibility to grant the level 7 user "view-only" rights on the Catalyst Device Manager?Thanks.Thanks.
Hi,
Check out the below link for SDM for read only user configuration
http://conft.com/en/US/docs/routers/access/cisco_router_and_security_device_manager/application/notes/SDMcli.pdf
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

I can no longer use all of the "Computer Management" tools against a remote computer. "Local Users and Groups", "Event Viewer", "Performance Logs and Alerts" and "Device Manager"

Hello All,
I can no longer use all of the "Computer Management" tools against a remote
computer. "Local Users and Groups", "Event Viewer", "Performance Logs and
Alerts" and "Device Manager"
kindly see the below snapshot for assistance
REGARDS DANISH DANIE

This link may help....
http://windowsxp.mvps.org/admintools.htm
Freeman

How to trigger other devices by Cisco Physical Access Management?

Hi all,
A question about Cisco Physical Access Management(PAM) here. We will achieve a goal like this:
step 1. A staff swipe the badge and get into the room;
step 2. The device in this room will be triggered to set up or to turn on at the same time, such as Ip-phone, light, screen of DMP...
step 3.(optional) When the staff exits the room and swipes the badge, all the devices will be turned off.
Is this dorable for PAM to finish this trigger? Or some more work of developing need to do based on PAM?
Thanks!
Ziwei Fan

Hi Bharaty,
thanks for your suggestion. I tried adding the tag as you suggested, sadly it does not work for me.
I had a little look at the coding in the tag, as I hope for the solution being in there. What makes me wonder is that I can specify the attribute TIMER in the tag, but the coding does not access it. The amount of time the "Please wait..." is shown is read from the technical profile.Which is 0 in my case.
Thus I tried setting it to 5000 in the debugger, but still no spinning thingy locking the UI.
Anyhow in the Scripts repository I found the JS functions usually used to trigger the functionality:
showSubmitInProgress(show, delay)
Even calling it directly does not work for me
I really suppose it has something to do with the area frame tag and the late rendering. It still keeps me wondering why I can not trigger server round trips from JS as I can normally do.
cheers Carsten

Can Cisco Device Manager Support ACS Authentication?

Background:
My company has approximately 500+ devices all across the country (mainly 2801's, 2924's, 2950's, and 2960's) and approx 3 people that have a real idea of how to configure the devices, and 2 or 3 that have a general clue about how to do it. I am in the process of moving all of these devices to use ACS authentication for signing into the device. While I am doing this I am establishing a strong password for the secret password to provide as a backup.
Problem:
My supervisor would like the cisco device manager to be available to the people that don't have the in depth cli experience. However in my testing, it will only accept the strong password for its authentication, and does not try the ACS server for authentication. Is this possible?

Hi,
Actually, there is a difference as from where the authentication is picked from for HTTP authentication,
With HTTP v1 server, same method list is picked, that is used by VTY lines.
With HTTP v1.1 server, but before the integration of fix for bug CSCeb82510, the method list defined for console is checked.
After the fix of the above mentioned bug, we have some different sent of commands that we can use.
I would suggest you to give this a try,
aaa authentication login CONSOLEandHTTP tacacs+ local
aaa authorization exec CONSOLEandHTTP if-authenticated
ip http authentication aaa
line con 0
login authentication CONSOLEandHTTP
authorization exec CONSOLEandHTTP
For detail please refer,
http://www.cisco.com/en/US/tech/tk59/technologies_tech_note09186a008069bdc5.shtml
Regards,
Prem

Devices in cisco view

Hi
what is the reason if can see , cisco devices in cisco view while you can't see some of these devices in topology service?
thanks in advance
Ibrahim

Ibrahim,
As you know some devices may not show up as connected to others due to their CDP neighbor adjacency not being determined for various reasons.
Please look under unconnected devices view on Topology to see if your "missing" devices are there. Another place you can check the same thing is within Device Center - click on the "Topology" tab near the top of the page and you should see the topology specific to that device. For something like and ASA (which doesn't support CDP), it will always show as "alone" and always be put into the Unconnected Devices view.

Ask the Expert : Call Recording with Cisco Unified Communication Manager (UCM)

Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about Cisco Unified CM call recording solution that provides the ability to record customer conversations for compliance purpose. This topic will cover an overview, configuration and troubleshooting of the call recording feature.
Monday, January 19th, 2015 to Friday, January 30th, 2015
Harmit Singh is a technical leader with the High Touch Technical Services (HTTS) and Technical Assistance Center (TAC) Unified Communications teams based in Bangalore. He has broad experience in Cisco Unified Communications infrastructure solutions. He has 10 years of experience working with large enterprise and service provider networks. He also holds CCIE certifications (#20012) in Voice and Collaboration as well as Red Hat and VMware certifications.
Mohammed Noorulla Khan is a customer support engineer in High-Touch Technical Services (HTTS) Unified Communications teams based in Bangalore. His areas of expertise include Cisco Unified Communications Manager, Gateways, and Jabber. He has over 6 years of industry experience working with large enterprise and service provider networks. He also holds CCIE certifications (#35741) in Voice and VMware certifications.
** Remember to use the rating system to let Mohammed and Harmit know if you've received an adequate response. **
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Collaboration, Voice and Video community, subcommunity, IP Telephony, shortly after the event. This event lasts through January 30th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.

Hi Maheshwar,
Thank you for your query. Please find my response below:
1> Do we support recording with HCS environment and which 3rd party vendors are validated with HCS based call control 10.1.1?
Answer: Whether you use a standalone UCM cluster, UCCE or HCS, call recording would be supported across the board in the same manner.
Please refer to the following link:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cust_contact/contact_center/hcs-cc/10_0_1/Install_and_Config/CHCS_BK_ICC270D0_00_installing-and-configuring-cisco-hcs/CHCS_BK_ICC270D0_00_installing-and-configuring-cisco-hcs_chapter_011.html#CHCS_RF_T1105284_00
Option
Notes
Recording
All Recording applications that are supported by Unified CCE are supported on HCS for CC. For details, see Recording section in Agent and Supervisor Capabilities.
With respect to which 3rd party vendors have been validated, marketplace.cisco.com is a good place to crosscheck this info. You will find a Cisco Compatible Logo against the partners listed there. The logo is used to signify that the PARTNER product has undergone technical interoperability testing with the Cisco product specified. The interoperability testing is conducted by a third party laboratory based on testing criteria set forth by Cisco. PARTNER is solely responsible for the support and warranty of its product. Placement of the PARTNER product or information pertaining thereto, on the Cisco Marketplace website does not constitute an offer to sell the PARTNER product in any way. For further information on the PARTNER products, please visit the PARTNER company website.
Please refer to the following link and use the search field under Collaboration Technology:
https://marketplace.cisco.com/catalog/search?utf8=%E2%9C%93&search[q]=&search[technology_category_ids]=23%2C24%2C197%2C1940%2C1941%2C1921%2C1576%2C1897%2C1983%2C2418%2C26%2C198%2C1904&search[order]=tier&per_page=20&_=1421663854257&ts=1421663855441
2> Which end points are supported for recording via HCS call control?
Answer: The following link should help clarify this:
http://solutionpartner.cisco.com/web/sip/wiki/-/wiki/Main/Unified+CM+Silent+Monitoring+Recording+Supported+Device+Matrix
Please let us know if you have any follow up questions. Hope this is helpful.
Regards,
Harmit Singh.

Cisco View Device Manager

Similar Messages

Maybe you are looking for