Cisco wap321 not responding

We have one WAP321 which stopping responding after being online for 24hrs. Currently we are just rebooting the device to get it up and running. However I would like to find a permanent fix.

Hi Martin,
Please do some changes in your AP and monitor unit 24 hours. Access unit GUI and do this following
go to Wireless --> Radio
in redio change
Channel to 1, 6, or 11
change Beacon Interval to 400
change DTIM Period to 4
Lefact Rate Sets:  uncheck 1 up and down, uncheck 2 up and down
click SAVE
monitor unit 24 hours
Thanks,
Moh

Similar Messages

  • Cisco ASA Not Responding to SNMP

    Hi All,
    I have a Cisco ASA that I am trying to discover with SNMP (Solar Winds). The Solarwinds server can ping the ASA on the E1 interface (on the same network as the server), yet it cannot be discovered using SNMP, it fails every time.
    This is the config I have for the ASA.
    interface GigabitEthernet0/0.224
    description NMS
    vlan 224
    nameif NMS
    security-level 100
    ip address 10.11.120.225 255.255.255.240
    snmp-server host NMS 10.11.120.235 community *****
    no snmp-server location
    no snmp-server contact
    snmp-server community *****
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    The server trying to discover the ASA is 10.11.120.235 and the community string is public.
    Also, I do not know how you add a RW string to a Cisco ASA - it seems to only let you add a single string.
    Thanks in advance.
    Dan

    Hi Daniel,
    The ASA supports only SNMP read-only access. SNMP write access is not allowed, so you cannot make changes with SNMP.
    Have you tried to manualy pool the ASA using snmpget or some other tools. One issue might be the community used by Solarwinds.
    Regards
    Dan

  • Cisco IPS Error -- errsystemerror-ct-sensorapp.333 not responding

    Hi Team,
    I am getting the below error while accessing IDM. I rebooted the device, after some times i get the same type of messages..
    error connecting to sensor + failed to load sensor. errsystemerror-ct-sensorapp.333 not responding. please check system processes- the connect to the specified lo::clientpipe failed.
    Will be appreciated for the quick reply on priority...
    regards
    Rajesh

    Hi,
    Pls find the below show version..
    Looks like all the processes are running..
    Application Partition:
    Cisco Intrusion Prevention System, Version 5.1(5)E1
    Host:
    Realm Keys key1.0
    Signature Definition:
    Signature Update S323.0 2008-03-24
    Virus Update V1.2 2005-11-24
    OS Version: 2.4.26-IDS-smp-bigphys
    Platform: IPS-4240-K9
    Serial Number: xxxxxxxxxxxx
    Licensed, expires: 01-Dec-2009 UTC
    Sensor up-time is 14:55.
    Using 512040960 out of 1454153728 bytes of available memory (35% usage)
    system is using 17.4M out of 29.0M bytes of available disk space (60% usage)
    application-data is using 44.1M out of 166.8M bytes of available disk space (28%
    usage)
    boot is using 35.3M out of 68.6M bytes of available disk space (54% usage)
    MainApp 2007_FEB_02_15_58 (Release) 2007-02-02T16:04:00-0600 Runn
    ing
    AnalysisEngine 2007_FEB_02_15_58 (Release) 2007-02-02T16:04:00-0600 Runn
    ing
    CLI 2007_FEB_02_15_58 (Release) 2007-02-02T16:04:00-0600
    Upgrade History:
    * IPS-K9-sp-5.1-5-E1 10:28:00 UTC Fri Feb 02 2007
    IPS-sig-S323-req-E1.pkg 07:26:42 UTC Tue Mar 25 2008
    Recovery Partition Version 1.1 - 5.1(5)E1

  • Cisco ips 4200 - errsystemerror-ct-sensorapp.443 not responding

    Hi team,
    Does anyone have come across the below error while accessing the cisco ips 4200 running with 7.0 version. The Gui closes automatically after this message.
    errsystemerror-ct-sensorapp.443 not responding, clientpipe failed.
    regards()

    Problem resolved by rebooting the device.. It is documented in cisco.
    http://www.cisco.com/en/US/products/hw/vpndevc/ps4077/products_qanda_item09186a008025c533.shtml
    When I attempt to log in to IPS, I receive this error message:
    errSystemError-ct-sensorAPP.450 not responding, clientpipe failed
    . How can I resolve this error?
    A. In order to resolve this error, use the reset command in order to reboot the IPS.
    Rate of this was helpful...

  • Cisco nexus 7706 Module x not responding... resetting

    Hello every body,
    we have in our data center 2 switches 7706 running NX-OS version 6.2(6a). One of them has notified that module 1 was not responding and rebooting it.
    2015 Mar 22 14:28:55 N7K-1 %MODULE-2-MOD_NOT_ALIVE: Module 1 not responding... resetting (Serial number: xxxx)
    2015 Mar 22 14:29:13 N7K-1 %PLATFORM-2-MOD_DETECT: Module 1 detected (Serial number xxxx) Module-Type 1/10 Gbps Ethernet Module Model N77-F348XP-23
    2015 Mar 22 14:29:13 N7K-1 %PLATFORM-2-MOD_PWRUP: Module 1 powered up (Serial number xxxx)
    2015 Mar 22 14:29:13 N7K-1 %PLATFORM-5-MOD_STATUS: Module 1 current-status is MOD_STATUS_POWERED_UP
    2015 Mar 22 14:30:50 N7K-1 %BIOS_DAEMON-SLOT1-5-BIOS_DAEMON_LC_PRI_BOOT:  System booted from Primary BIOS Flash
    2015 Mar 22 14:32:09 N7K-1 %VDC_MGR-5-VDC_STATE_CHANGE: vdc 1 state changed to updating
    2015 Mar 22 14:32:09 N7K-1 %VDC_MGR-5-VDC_STATE_CHANGE: vdc 1 state changed to active
    2015 Mar 22 14:32:33 N7K-1 %PLATFORM-5-MOD_STATUS: Module 1 current-status is MOD_STATUS_ONLINE/OK
    2015 Mar 22 14:32:33 N7K-1 %MODULE-5-MOD_OK: Module 1 is online (Serial number: xxxx)
    2015 Mar 22 14:32:33 N7K-1 %SYSMGR-SLOT1-5-MODULE_ONLINE: System Manager has received notification of local module becoming online.
    Fiew months ago we have the same symptom with module 6 instead of 1.
    Note that the VPC peer-link is connected over 2x10G interfaces on each of these 2 modules.
    Is there any known issue with this NX-OS version 6.2(6a)?

    Hi,
    I see that the module reloaded  to recover from a EOBC heartbeat failure.
    108) At 955385 usecs after Sun Mar 22 14:28:55 2015
        Sequence initiation: LC removal
    109) At 955209 usecs after Sun Mar 22 14:28:55 2015
        Sending MTS_OPC_LC_STATUS_CHANGE to Registry
    110) At 955206 usecs after Sun Mar 22 14:28:55 2015
        Received MTS_OPC_LCP_NOT_RESPONDING from Line card manager
    111) At 955148 usecs after Sun Mar 22 14:28:55 2015
        Sending MTS_OPC_LCP_NOT_RESPONDING to Line card manager
    112) At 458025 usecs after Sun Mar 22 14:28:19 2015
        Warning on ports: 1-0 due to EOBC heartbeat failure in device 10
    Device error code: 0xc0a0
    113) At 457788 usecs after Sun Mar 22 14:28:19 2015
        Received MTS_OPC_LC_RUNTIME_DIAG_FROM_SUP from EOBC monitor kernel SAP
    114) At 435569 usecs after Sun Mar 22 14:28:19 2015
        Warning on ports: 1-0 due to EOBC heartbeat failure in device 10
    Device error code: 0xc0a0
    115) At 435312 usecs after Sun Mar 22 14:28:19 2015
        Received MTS_OPC_LC_RUNTIME_DIAG_FROM_SUP from EOBC monitor kernel SAP
    N7K-1# show module internal exceptionlog module 1
    ********* Exception info for module 1 ********
    exception information --- exception instance 1 ----
    Module Slot Number: 1
    Device Id         : 10
    Device Name       : eobc
    Device Errorcode  : 0xc0a0314f
    Device ID         : 10 (0x0a)
    Device Instance   : 03 (0x03)
    Dev Type (HW/SW)  : 01 (0x01)
    ErrNum (devInfo)  : 79 (0x4f)
    System Errorcode  : 0x4042004e EOBC heartbeat failure
    Error Type        : Warning
    PhyPortLayer      : Ethernet
    Port(s) Affected  :
    DSAP              : 0 (0x0)
    UUID              : 0 (0x0)
    Time              : Sun Mar 22 14:28:19 2015
                        (Ticks: 550EC373 jiffies)
    exception information --- exception instance 2 ----
    Module Slot Number: 1
    Device Id         : 10
    Device Name       : eobc
    Device Errorcode  : 0xc0a0314d
    Device ID         : 10 (0x0a)
    Device Instance   : 03 (0x03)
    Dev Type (HW/SW)  : 01 (0x01)
    ErrNum (devInfo)  : 77 (0x4d)
    System Errorcode  : 0x4042004e EOBC heartbeat failure
    Error Type        : Warning
    PhyPortLayer      : Ethernet
    Port(s) Affected  :
    DSAP              : 0 (0x0)
    UUID              : 0 (0x0)
    Time              : Sun Mar 22 14:28:19 2015
                        (Ticks: 550EC373 jiffies)
    The EOBC is Ethernet Out of Band Channel.  
    There are regular keepalives or 'heartbeats' going between the sup and line cards.  The error messages you received indicate a heartbeat went missing between SUP and linecard. 
    If a single heartbeat went missing, it will be corrected automatically, however if multiple heartbeats are lost simultaneously then the line card would be reset (sup would power off and power on that slot in attempt to resolve a diagnostic issue).
    So if the card is stable after that you can consider this as a one time (transient) issue.
    You can also check EOBC stats to see if any error increasing.
    show hardware internal eobc stats
    show hardware internal eobcsw stats
    show hardware internal cpu-mac eobc stats
    show hardware internal cpu-mac eobc events
    show hardware capacity eobc
    Hope this helps. 
    PS : Please grade all posts which are useful.
    Thanks,
    Madhu.

  • TAC+: TCP/IP open to 10.20.17.2/49 failed -- Connection timed out; remote host not responding

     TACACS+ configured on router and router is in ACS.  I can ping the ACS but the router cannot establish a connection to authenticate users.
    aaa group server tacacs+ hq_acs-1
    server 10.20.17.2
    ip tacacs source-interface GigabitEthernet0/0
    aaa authentication login default group tacacs+ local
    aaa authorization config-commands
    aaa authorization exec default group tacacs+ local
    aaa authorization commands 10 default group tacacs+ local
    aaa authorization commands 15 default group tacacs+ local
    aaa accounting nested
    aaa accounting update newinfo periodic 60
    aaa accounting auth-proxy default start-stop group tacacs+
    aaa accounting exec default start-stop group tacacs+
    aaa accounting commands 15 default start-stop group tacacs+
    aaa accounting network default start-stop group tacacs+
    aaa accounting connection default start-stop group tacacs+
    aaa accounting system default start-stop group tacacs+
    aaa accounting resource default start-stop group tacacs+
    BigTree_3945#sh ip int br
    Interface                  IP-Address      OK? Method Status                Protocol
    GigabitEthernet0/0         10.4.3.1        YES NVRAM  down                  down
    GigabitEthernet0/1         10.12.10.26     YES NVRAM  up                    up 
    Serial0/2/0                unassigned      YES NVRAM  down                  down
    Serial0/2/0.602            10.12.15.10     YES NVRAM  down                  down
    Apr 13 11:08:13.673: TPLUS: Queuing AAA Authentication request 79 for processing
    Apr 13 11:08:13.673: TPLUS: processing authentication start request id 79
    Apr 13 11:08:13.675: TPLUS: Authentication start packet created for 79(cisscdb)
    Apr 13 11:08:13.675: TPLUS: Using server 10.20.17.2
    Apr 13 11:08:13.675: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: Started 5 sec timeout
    Apr 13 11:08:18.676: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out
    Apr 13 11:08:18.676: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out, clean up
    Apr 13 11:08:18.676: TPLUS(0000004F)/0/1BDD9C34: Processing the reply packet
    Apr 13 11:08:25.834: TPLUS: Queuing AAA Authentication request 79 for processing
    Apr 13 11:08:25.834: TPLUS: processing authentication start request id 79
    Apr 13 11:08:25.834: TPLUS: Authentication start packet created for 79(cisscdb)
    Apr 13 11:08:25.834: TPLUS: Using server 10.20.17.2
    Apr 13 11:08:25.834: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: Started 5 sec timeout
    Apr 13 11:08:30.836: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out
    Apr 13 11:08:30.836: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out, clean up
    Apr 13 11:08:30.836: TPLUS(0000004F)/0/1BDD9C34: Processing the reply packet
    Apr 13 11:08:43.689: TAC: Using default tacacs server-group "tacacs" list.
    Apr 13 11:08:43.689: TAC+: Opening TCP/IP to 10.20.17.2/49 timeout=5
    Apr 13 11:08:51.057: TPLUS: Queuing AAA Authentication request 79 for processing
    Apr 13 11:08:51.057: TPLUS: processing authentication start request id 79
    Apr 13 11:08:51.057: TPLUS: Authentication start packet created for 79(cisscdb)
    Apr 13 11:08:51.057: TPLUS: Using server 10.20.17.2
    Apr 13 11:08:51.057: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: Started 5 sec timeout
    Apr 13 11:08:54.692: TAC+: TCP/IP open to 10.20.17.2/49 failed -- Connection timed out; remote host not responding
    Apr 13 11:08:54.692: TPLUS: Queuing AAA Accounting request 76 for processing
    Apr 13 11:08:54.692: TPLUS: processing accounting request id 76
    Apr 13 11:08:54.692: TPLUS: Sending AV task_id=332
    Apr 13 11:08:54.692: TPLUS: Sending AV timezone=EDT
    Apr 13 11:08:54.692: TPLUS: Sending AV service=shell
    Apr 13 11:08:54.692: TPLUS: Sending AV start_time=1334329734
    Apr 13 11:08:54.692: TPLUS: Sending AV priv-lvl=15
    Apr 13 11:08:54.692: TPLUS: Sending AV cmd=show logging <cr>
    Apr 13 11:08:54.692: TPLUS: Accounting request created for 76(n20j03t)
    Apr 13 11:08:54.692: TPLUS: Using server 10.20.17.2
    Apr 13 11:08:54.692: TPLUS(0000004C)/1/NB_WAIT/20FD90EC: Started 5 sec timeout
    Apr 13 11:08:56.058: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out
    Apr 13 11:08:56.058: TPLUS(0000004F)/0/NB_WAIT/1BDD9C34: timed out, clean up
    Apr 13 11:08:56.058: TPLUS(0000004F)/0/1BDD9C34: Processing the reply packet
    Apr 13 11:08:59.693: TPLUS(0000004C)/1/NB_WAIT/20FD90EC: timed out
    Apr 13 11:08:59.693: TPLUS(0000004C)/1/NB_WAIT/20FD90EC: timed out, clean up
    Apr 13 11:08:59.693: TPLUS(0000004C)/1/20FD90EC: Processing the reply packet
    BigTree_3945#
    AAA Client IP Address
    10.4.3.* 10.12.15.10
    Key
    Network Device Group
    Test    
    NJT    
    AccessLink    
    (Not Assigned)    
    Authenticate Using
    TACACS+ (Cisco IOS)    
    RADIUS (Cisco Aironet)    
    RADIUS (Cisco BBSM)    
    RADIUS (Cisco IOS/PIX)    
    RADIUS (Cisco VPN 3000)    
    RADIUS (Cisco VPN 5000)    
    RADIUS (IETF)    
    RADIUS (Ascend)    
    RADIUS (Juniper)    
    RADIUS (Nortel)    
    RADIUS (iPass)    
    Single Connect TACACS+ AAA Client (Record stop in accounting on failure).
    The 10.12.10.* range is listed under the HQ site.
    Your help is greatly appreciated.

    You stated that you can ping ACS from the router, did you try sourcing the packets from the GigabitEthernet 0/0 interface (which is the one TACACS+ will try to use, given the configuration that you posted)?
    What does the network path between the router and ACS look like (ie, any firewalls, NAT, etc)?
    Can you connect to port 49 at the ACS IP address from the router sourcing the packets from GigabitEthernet 0/0 ?
    Are you using VRFs?
    What version of IOS?

  • WLS 10.3 Does not respond to GET requests (HTTP/1.0)

    Hi All,
    I have 2 WLS servers running on separate physical hosts behind a cisco CSS load balancer. The keep-alive method the Cisco CSS uses is HTTP GET messages. This keep-alive method does not appear to work, because my WLS servers are not responding to the GET requests with HTTP 200 OKs (as would be expected). These GET messaged appear in the access logs, as follows, but from traces taken on the host, there are no HTTP 200 messages ever transmitted. I see no exceptions or errors related to this in the server or access logs.
    WLS access log:
    192.168.1.1 - - [14/Dec/2011:18:23:35 +0000] "HEAD /APPDIR/index.jsp HTTP/1.0" 200 0
    192.168.1.1 - - [14/Dec/2011:18:23:45 +0000] "HEAD /APPDIR/index.jsp HTTP/1.0" 200 0
    192.168.1.1 - - [14/Dec/2011:18:23:55 +0000] "HEAD /APPDIR/index.jsp HTTP/1.0" 200 0
    Interestingly, If i use a http-ping tool to send HEAD messages, the server correctly responds with the 200. A major difference between the CSS and the ping-tool, is that the CSS is using HTTP/1.0 where the ping tool uses HTTP/1.1. The GET requests are formatted a bit differently too. Below is how the different GET messages are formatted. Is it possible that WLS 11g does not support HTTP/1.0? Is there any method of debugging that I can employ to troubleshoot this further? As mentioned I do not see any errors or exceptions in the server logs or access logs....
    Many thanks, in advance.
    HTTP-PING TOOL HEAD MESSAGE - weblogic responds to this message
    HEAD /APPDIR/index.jsp HTTP/1.1
    Host: myhost.domain.com:7005
    Accept: */*
    LOAD BALANCER HEAD MESSAGE -weblogic does not respond to this message
    HEAD /APPDIR/index.jsp HTTP/1.0
    Connection: Keep-Alive
    User-Agent: Mozilla/4.06 [en] (WinNT; I)
    Accept: image/gif, image/x-bitmap, image/jpeg, image/pjpeg, image/png, */*
    Accept-Language: en
    Accept-Charset: iso-8859-1,*,utf-8
    Host: 192.168.1.66

    Other than failing the base address test, does the device seem to work in the test panels? One quick test would be to open the digital I/O panel, change some of the lines to output, toggle the logic levels, and see if the line states track the logic levels. Also, you can switch to the Counter I/O panel, change the mode to simple event counting, set the event source to the internal 100KHz clock, and start the counter. If the counter is working properly, you should see the counter value increase at a rate of 100000/second.
    If the test panels seem to work OK, you may still be able to use the board, despite the resource test failing. I still can't explain why the test fails, though.
    Joe

  • 'User did not respond' - Has something changed with ichat?

    This seems to be an issue for nearly everyone. I have been using ichat video succesfully for over a year now. For some reason, in the last month or so, the video has stopped working on all three of my macs (powerbook G4 Tit, new mbpro, and imac g5 at home)
    From my tibook (10.3.9)...I can sucessfully connect to the apple test video without problem. The person I am trying to videochat with can also connect to the same apple test video with no problem. However, we cannot chat with video OR audio with each other.
    I have done a bandwidth test, and I am on a 1.5 T1. I am behind a company NAT (cisco 1700 router, Novell server handling the nat/pat) He is in LA and has succesfully be chatting with people on the east coast, so I don't think he is the issue.
    Here is the log from the connection doctor:
    2006-05-16 09:33:45 -0700: REMOTE USER NAME HERE did not respond.
    Tried to send UDP SIP "invite" to the following IP addresses and ports:
    69.229.11.215:5060, 192.168.15.100:5060, 172.16.1.35:5060
    2006-05-16 09:40:51 -0700: REMOTE USER NAME HERE did not respond.
    Tried to send UDP SIP "invite" to the following IP addresses and ports:
    69.229.11.215:5060, 192.168.15.100:5060, 172.16.1.35:5060
    2006-05-16 09:47:26 -0700: REMOTE USER NAME HERE did not respond.
    Tried to send UDP SIP "invite" to the following IP addresses and ports:
    69.229.11.215:5060, 192.168.15.100:5060, 172.16.1.35:5060
    2006-05-16 09:53:33 -0700: REMOTE USER NAME HERE did not respond.
    Tried to send UDP SIP "invite" to the following IP addresses and ports:
    69.229.11.215:5060, 192.168.15.100:5060, 172.16.1.35:5060
    As it has been for nearly everyone else on the list, I am extremely frustrated. I have never had an issue using ichat, but now I can't get it to work from anywhere. I have been able to get everyone in my family to switch to imacs so they can chat with my kids....and now we can't get it to work at all.
    What am I missing? I find it hard to believe that this is so hard to use that so many people are not able to use it.
    Any help or new suggestions would be most appreciated.
    sqe

    I'm new to Macs and bought a MacBook Pro for myself and partner mostly for the iChat AV feature. Neadless to say, I'm frustrated beyond belief. I've spent over 25 hours trying to get it to work to no avail.
    Each of us can connect with the Apple test buddies with no problem. We can't connect with each other though, except for two times that it actually worked.
    I've troubleshooted everything I can think of. I've called my ISP (Verizon), Netgear (my wireless router), and just this morning I called Apple. I was at work so, I'll have to call them back when I get home but they don't seem to even know about the problem. Which is astonishing considering how many people are reporting this on the forum.
    I can connect to anyone while on my office wi-fi but only to the Apple test buddies when at home. That's why I called my ISP and Netgear. I took the router out of the picture and still had the same problem at home.
    It makes no sense that the Apple test buddies do work but not real people.

  • VSAN Isolation due to domain manager other side not responding

    I am trying to configure VE port between Cisco nexus 7K and 5K switches but the vfc is not operational as VSAN isolation.
    I have bind the VSAN 100 to VLAN 100 and add vfc into vsan database, but the VSAN 100 is still operational down                  
    error msg shown: VSAN Isolation due to domain manager other side not responding?
    StorageVDC# show vlan fcoe
    Original VLAN ID        Translated VSAN ID      Association State
          100                       100              Operational
    vsan 100 information
             name:VSAN0100  state:active
             interoperability mode:default
             loadbalancing:src-id/dst-id/oxid
             operational state:down <<<<
    StorageVDC# show vlan
    VLAN Name                             Status    Ports
    1    default                          active    Eth2/5
    100  VLAN0100                         active    Po401, Eth2/3, Eth2/4
    StorageVDC# show int vfc-port-channel 401
    vfc-po401 is trunking (Not all VSANs UP on the trunk)
        Bound interface is port-channel401
        Hardware is Ethernet
        Port WWN is xxxxx
        Admin port mode is E, trunk mode is on
        snmp link state traps are enabled
        Port mode is TE
        Port vsan is 100
        Speed is 20 Gbps
        Trunk vsans (admin allowed and active) (100)
        Trunk vsans (up)                       ()
        Trunk vsans (isolated)                 (100) <<<<<
        Trunk vsans (initializing)             ()
        608 fcoe in packets
        51072 fcoe in octets
        1762 fcoe out packets
        135612 fcoe out octets
        Interface last changed at Thu Jan 10 10:47:27 2013

    Well, it wasn't a DNS issue, it was a routing issue that affected ISP customers in half of the country. https://community.shaw.ca/thread/9284?start=0&tstart=0
    I can confirm that iTunes will now open and is functional. It seems that if the application can't access some internet resource immediately when it launches it will immediately lock up and never come back! No offline mode??!?!

  • AUSST fresh synchronization - server not responding ...

    Hello. We have just subscribed a number of people to CCT. I have created the necessary packages successfully. Now, I am in the process of setting up AUSST for the first time. I have tried on both a Windows Server 2003 SP3 and Windows Server 2008R2 server with the same results. It gets to a certain point and then seems to timeout. See command prompt text below.
    Is this simply network conjestion somewhere and I just have to keep trying until I jag it sometime? We have a 10Mb Fibre connection and I am doing it at a quiet time of the evening. Therefore, I don't think its my end.
    Any other ideas?
    Here is a copy of the command prompt:
    C:\Documents and Settings\Administrator.BW\My Documents\Downloads\AUSST>AdobeUpdateServerSetupTool --root="\websites\adobeupdates\cct"
    Choose one of the following options  :
    1. Fresh Synchronization.
    2. Incremental Synchronization.
    3. Generate Client Configuration XML.
    4. Migrate to an In-House Server.
    5. Exit.
    Your choice: 1
    Fresh Synchronization chosen.
    Folder exists at given root path! All the contents of the folder will be deleted.
    Enter 'Y' to continue or any other key to exit: Y
    Processed 21 out of Server not responding.                                    1048 items. \
    Processed 25 out of 1048 items.
    Error in 2 items.
    AdobeUpdateServerSetupTool returned with code: 5.
    For more information refer AdobeUpdateServerSetupTool.log at C:\DOCUME~1\ADMINI~1.BW\LOCALS~1\Temp\1\ .
    Here is a copy of the log:
    09/03/13 17:51:58:102 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2780 | Rootpath = \websites\adobeupdates\cct
    09/03/13 17:52:09:868 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2780 | Folder exists at given root path! All the contents of the folder will be deleted.
    09/03/13 17:52:13:337 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2780 | Item downloaded \websites\adobeupdates\cct\webfeed\oobe\aam10\win\.
    09/03/13 17:52:13:837 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2780 | Item downloaded \websites\adobeupdates\cct\webfeed\oobe\aam10\win\.
    09/03/13 17:52:14:650 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2780 | Item downloaded \websites\adobeupdates\cct\webfeed\oobe\aam20\win\.
    09/03/13 17:52:15:134 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2780 | Item downloaded \websites\adobeupdates\cct\webfeed\oobe\aam10\mac\.
    09/03/13 17:52:15:618 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2780 | Item downloaded \websites\adobeupdates\cct\webfeed\oobe\aam20\mac\.
    09/03/13 17:52:16:056 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2796 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\PhotoshopCameraRawForElements10-6.4\6.7 .040\.
    09/03/13 17:52:16:056 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2792 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\PhotoshopCameraRaw-6.0\6.7.040\.
    09/03/13 17:52:16:087 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2788 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AdobeDrive3-3.0.0\3.2.0\.
    09/03/13 17:52:17:368 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\PhotoshopCameraRawForElements10-6.4-x64 \6.7.040\.
    09/03/13 17:52:18:634 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AAMEE-2.0\2.1.0\.
    09/03/13 17:52:23:306 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AAMEE-2.0\2.1.0\.
    09/03/13 17:52:24:353 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11cs_CZ\2.0.1\.
    09/03/13 17:52:25:134 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11de_DE\2.0.1\.
    09/03/13 17:52:26:134 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11en_US\2.0.1\.
    09/03/13 17:52:28:588 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11es_ES\2.0.1\.
    09/03/13 17:52:29:322 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11fr_FR\2.0.1\.
    09/03/13 17:52:30:619 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11it_IT\2.0.1\.
    09/03/13 17:52:31:400 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11ja_JP\2.0.1\.
    09/03/13 17:52:32:588 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11ko_KR\2.0.1\.
    09/03/13 17:52:34:010 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11nl_NL\2.0.1\.
    09/03/13 17:52:37:651 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11pl_PL\2.0.1\.
    09/03/13 17:52:38:697 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11pt_BR\2.0.1\.
    09/03/13 17:52:40:072 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11ru_RU\2.0.1\.
    09/03/13 17:52:41:151 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11sv_SE\2.0.1\.
    09/03/13 17:52:41:526 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11tr_TR\2.0.1\.
    09/03/13 17:52:41:901 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11zh_CN\2.0.1\.
    09/03/13 17:52:42:698 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIR2ForFlashPro11zh_TW\2.0.1\.
    09/03/13 17:52:43:401 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIRforIOSFlashBuilder2.6\2.6.1\.
    09/03/13 17:53:33:824 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AIRforIOSFlashBuilder2.6\2.6.1\.
    09/03/13 17:53:35:027 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AdobeAPE3_Win64_NoLocale\3.1\.
    09/03/13 17:54:32:465 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2788 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AdobeDrive3-3.0.0\3.2.0\.
    09/03/13 17:54:32:840 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2788 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AdobeAPE3_Win_NoLocale\3.1\.
    09/03/13 17:54:32:996 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AdobeAPE3_Win64_NoLocale\3.1\.
    09/03/13 17:54:34:231 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AdobeAfterEffectsCS5-10-Retail\10.0.1\.
    09/03/13 17:54:39:637 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2796 | Item failed \websites\adobeupdates\cct\updates\oobe\aam10\win\PhotoshopCameraRawForElements10-6.4\6.7 .040\Setup.zip.
    09/03/13 17:54:39:778 | [WARN] |  | AAMEE | Utilities | AUSST |  |  | 2796 | Unable to download update file \websites\adobeupdates\cct\updates\oobe\aam10\win\PhotoshopCameraRawForElements10-6.4\6.7 .040\Setup.zip
    09/03/13 17:54:39:778 | [ERROR] |  | AAMEE | Utilities | AUSST |  |  | 2796 | Server not responding.                                   
    09/03/13 17:55:00:731 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2788 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\AdobeAPE3_Win_NoLocale\3.1\.
    09/03/13 17:55:58:029 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Item failed \websites\adobeupdates\cct\updates\oobe\aam10\win\AdobeAfterEffectsCS5-10-Retail\10.0.1\S etup.zip.
    09/03/13 17:55:58:154 | [WARN] |  | AAMEE | Utilities | AUSST |  |  | 2800 | Unable to download update file \websites\adobeupdates\cct\updates\oobe\aam10\win\AdobeAfterEffectsCS5-10-Retail\10.0.1\S etup.zip
    09/03/13 17:55:58:748 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2792 | Item downloaded \websites\adobeupdates\cct\updates\oobe\aam10\win\PhotoshopCameraRaw-6.0\6.7.040\.
    09/03/13 17:55:58:748 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2780 | Item: \websites\adobeupdates\cct\updates\oobe\aam10\win\PhotoshopCameraRawForElements10-6.4\6.7 .040\
    09/03/13 17:55:58:748 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2780 | Item: \websites\adobeupdates\cct\updates\oobe\aam10\win\AdobeAfterEffectsCS5-10-Retail\10.0.1\
    09/03/13 17:55:58:748 | [INFO] |  | AAMEE | Utilities | AUSST |  |  | 2780 | AdobeUpdateServerSetupTool Returned with code: 5.
    Regards
    Ian.

    Thanks Sumita and Philadendron.
    I have tried both fresh and incremental sync at various times of the day up to about 11pm AEST. They have all failed at around the 20 items mark.
    As 99.9% of our staff work 8am to 6pm, bandwidth after 6pm is not a problem. As i indicated before, we also have a 10Mb Ethernet over Fibre connection. My firewall (pfsense) graphs the bandwidth in realtime. When I start AUSST, I see the bandwidth reach 10Mb until AUSST fails and the bandwidth use returns to its normal very low level.
    I usually have no problems downloading large programs from companies such as Autodesk or Linux (4GB) DVD ISO files from CentOS etc. This is something I usually do during the evening and find the bandwidth available more than adequate.
    I think my setup is somewhat different to yours, Philadendron. Here are some details:
    Our fibre terminates at a Cisco router (don't recall model) configured as a bridge. This is connected to a dedicated NIC on one our ESX4 hosts. Our firewall is pfSense 2.0.3 running as a VM on the ESX host. Our ESX hosts connect to the LAN through a HP 2810-24G switch. Our ESX hosts are HP DL380G6's with a mix of Intel and Broadcom NICs. I'm not sure which NIC is dedicated to the WAN.
    The first machine i tried AUSST on was Windows Server 2003 running as a KVM VM on a CentOS 6.4 (x64) host. This host hardware is an old Dell Poweredge 840. It is connected to the same HP2810 switch as the ESX hosts.
    The other machine I have tried is a HP Probook 6560b laptop running Windows 7 Pro x64. It is connected to a small desktop switch in my office. This in turn is connected to LAN switch in the server room. The LAN switch is connected to the HP2810 via 2 x 1Gb aggregated links.
    In both cases, the LAN IP of both machines is configured to completely bypass the firewall proxy server (squid). In fact, I have even disabled squid completely to see if this made any difference. It didn't.
    There is no bandwidth throttling. In fact, I was wondering if bandwidth throttling might work. Perhaps the adobe update server is getting overwhelmed by the speed of the requests. That doesn't seem plausible but when nothing else seems to be working, I usually start looking at the less plausible options. When I get a chance, I may try AUSST from a regional office using a Telstra ADSL2+ WAN link. These are considerably slower than our 10Mb fibre link. However, I don't really expect any difference.
    I also don't want our staff all downloading the updates individually. However, at this stage we only have 4. So it is somewhat easier to manage than 20+!
    If I think of anything, I will update this thread. However, I don't believe it is at our end unless something is going on with our service provider (Telstra). This is highly unlikely though.
    Regards
    Ian.

  • Cisco WAP321 Captive Portal Redirect

    Hi I have setup a Cisco WAP321 as an Internet Cafe Captive Portal. When initially switched on clients connect and are redirected to the Log on page where they can add their name and tick to say they agree with the usage policy.
    Works great, unfotunately the next day when the clients connect again they are never redirected to the logon page so cant access the internet.
    I have tried putting in the redirect url and if i do that it works fine.
    I have checked all my settings but cant find out why.
    Anyone know why im not getting the redirect?
    Thanks
    Darren

    Hi Luis
    Thanks for the reply. I have been reading up on possible issues and just need to clarify whether the Guest WIFI has to be on VAP0? I have it configured on VAP2 and as i said initially it works OK and gives me the Redirect.
    My WAP321 is connected to a Cisco 887 Router with the Port set to Trunk and the VAP2 is set to Vlan2.
    VLAN 1 set to 192.168.192.1 255.255.255.128 and VLAN2 set to 192.168.192.193 255.255.255.224. DHCP scope on the Router is from 192.168.192.194 to 192.168.192.220.
    Im back on site again this morning and its working after a reset. Ill monitor over the next day or so and see what happens
    Regards
    Darren

  • RV220W reports the remote gateway is not responding.

    Hi, I've just set-up one of the RV220W VPN solutions.
    This worked fine for a while, but now it reports the remote gateway is not responding.
    Other clients can connect, but not the computer I'm using at home.
    Logfile reports:
    2011/08/31 21:10:31 [STATUS]Success to connect.
    2011/08/31 21:10:31 [STATUS]Tunnel is configured. Ping test is about to start.
    2011/08/31 21:10:31 [STATUS]Verifying Network...
    2011/08/31 21:10:37 [WARNING]Failed to ping remote VPN Router!
    2011/08/31 21:10:40 [WARNING]Failed to ping remote VPN Router!
    2011/08/31 21:10:43 [WARNING]Failed to ping remote VPN Router!
    2011/08/31 21:10:46 [WARNING]Failed to ping remote VPN Router!
    2011/08/31 21:10:49 [WARNING]Failed to ping remote VPN Router!
    2011/08/31 21:11:01 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
    2011/08/31 21:11:03 [STATUS]Disconnecting...
    2011/08/31 21:11:07 [STATUS]Success to disconnect.
    2011/08/31 21:15:07 [STATUS]OS Version: Windows 7
    2011/08/31 21:15:07 [STATUS]Windows Firewall Domain Profile Settings: ON
    2011/08/31 21:15:07 [STATUS]Windows Firewall Private Profile Settings: ON
    2011/08/31 21:15:07 [STATUS]Windows Firewall Private Profile Settings: ON
    2011/08/31 21:15:07 [STATUS]One network interface detected with IP address 192.168.2.2
    2011/08/31 21:15:07 [STATUS]Connecting...
    2011/08/31 21:15:07 [DEBUG]Input VPN Server Address = 81.167.1.1
    2011/08/31 21:15:07 [STATUS]Connecting to remote gateway with IP address: 81.167.1.1
    2011/08/31 21:15:07 [WARNING]Server's certificate doesn't exist on your local computer.
    2011/08/31 21:15:09 [STATUS]Remote gateway was reached by https ...
    2011/08/31 21:15:09 [STATUS]Provisioning...
    2011/08/31 21:15:17 [STATUS]Success to connect.
    2011/08/31 21:15:17 [STATUS]Tunnel is configured. Ping test is about to start.
    2011/08/31 21:15:17 [STATUS]Verifying Network...
    2011/08/31 21:15:22 [WARNING]Failed to ping remote VPN Router!
    2011/08/31 21:15:25 [WARNING]Failed to ping remote VPN Router!
    2011/08/31 21:15:28 [WARNING]Failed to ping remote VPN Router!
    2011/08/31 21:15:31 [WARNING]Failed to ping remote VPN Router!
    2011/08/31 21:15:34 [WARNING]Failed to ping remote VPN Router!
    2011/08/31 21:15:46 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
    2011/08/31 21:16:49 [STATUS]Disconnecting...
    2011/08/31 21:16:53 [STATUS]Success to disconnect.
    I've tried the most common stuff.
    Enabling ICMP, checked that remote administration runs on port 443, changed MTU to 1400 manually, It allows fragmented packages too.
    Checked that IKE and IPSec services are running.
    I've also tried both with windows firewall ON and OFF.
    A collegue of mine had the same problem in the same timeframe as me, but after a while - he suddently was able to connect.
    I still can't!!
    Firmware Version:        1.0.2.4
    Anyone got a fix for this?    
    Edit: IP is not real.   

    Ok, so I had a chat with Cisco - and it seems like the setup on the RV220W was done correctly and was working fine.
    Showed me a few things that could come in handy checking out when running diag on the quickvpn.
    I disabled all antivirus realtime checks, opened 443 and 500 inbound to my computer - checked that the QuickVPN.exe had an exception in the windows firewall, and that the firewall was enabled.
    Also checked that the services was set tu Auto and Started.
    Rebooted computer, and I was able to connect!
    Now I'm working my way back to the setup I had, to figure out what went wrong in the first place.

  • Loginwindow (Not Responding) after iTunes & Quicktime update

    In order to activate my new iPhone this morning I needed to upgrade to iTunes 7.5 and the corresponding Quicktime update. After a reboot and logging in I was presented with the desktop, the dock and a spinning beachball . . . which still hadn't gone away after 10 minutes.
    After a while I tried a few things and noticed that the dock was working, until I ctrl clicked on the finder icon that is. After that the dock froze and I rebooted with a long power button press. After logging again I had the same problem, desktop, working dock and spinning beachball.
    This time I hit one of my dock stacks and launched the Activity Monitor, only to discover that a process called 'loginwindow' was Not Responding. On force quitting this everything went away and I was back to the login prompt. I logged in again and found the same thing - I can use all the applications I can get to through the dock but have no finder . . .
    Any ideas?? HELP!!

    OK, here's /var/log/system.log from boot. Are the following two lines significant??
    Nov 10 21:40:43 Macintosh com.apple.launchd[1] (com.apple.UserEventAgent-LoginWindow[119]): Exited: Terminated
    Nov 10 21:40:43 Macintosh com.apple.launchctl.Aqua[131]: launchctl: Couldn't stat("/etc/machinit_peruser.d"): No such file or directory
    Nov 10 21:39:57 localhost kernel[0]: Darwin Kernel Version 9.0.0: Tue Oct 9 21:37:58 PDT 2007; root:xnu-1228~1/RELEASE_PPC
    Nov 10 21:39:47 localhost com.apple.launchctl.System[2]: /dev/disk0s3 on / (hfs, local, journaled)
    Nov 10 21:39:49 localhost com.apple.launchctl.System[2]: launchctl: Please convert the following to launchd: /etc/mach_init.d/dashboardadvisoryd.plist
    Nov 10 21:39:49 localhost com.apple.launchd[1] (org.cups.cupsd): Unknown key: SHAuthorizationRight
    Nov 10 21:39:49 localhost com.apple.launchd[1] (org.ntp.ntpd): Unknown key: SHAuthorizationRight
    Nov 10 21:39:54 localhost fseventsd[31]: event logs in /.fseventsd out of sync with volume. destroying old logs. (19369 21 20061)
    Nov 10 21:39:58 localhost kernel[0]: standard timeslicing quantum is 10000 us
    Nov 10 21:39:54 localhost fseventsd[31]: log dir: /.fseventsd getting new uuid: C00E1A09-A514-48BA-A79D-C46786E0EE9E
    Nov 10 21:39:58 localhost kernel[0]: vmpagebootstrap: 380993 free pages and 12223 wired pages
    Nov 10 21:39:58 localhost kernel[0]: migtable_maxdispl = 79
    Nov 10 21:39:58 localhost kernel[0]: 105 prelinked modules
    Nov 10 21:39:58 localhost kernel[0]: Loading security extension com.apple.security.TMSafetyNet
    Nov 10 21:39:58 localhost kernel[0]: calling mpopolicyinit for TMSafetyNet
    Nov 10 21:39:58 localhost kernel[0]: Security policy loaded: Safety net for Time Machine (TMSafetyNet)
    Nov 10 21:39:58 localhost kernel[0]: Loading security extension com.apple.nke.applicationfirewall
    Nov 10 21:39:58 localhost kernel[0]: Loading security extension com.apple.security.seatbelt
    Nov 10 21:39:58 localhost kernel[0]: calling mpopolicyinit for mb
    Nov 10 21:39:58 localhost kernel[0]: Seatbelt MACF policy initialized
    Nov 10 21:39:58 localhost kernel[0]: Security policy loaded: Seatbelt Policy (mb)
    Nov 10 21:39:58 localhost kernel[0]: Copyright (c) 1982, 1986, 1989, 1991, 1993
    Nov 10 21:39:58 localhost kernel[0]: The Regents of the University of California. All rights reserved.
    Nov 10 21:39:58 localhost kernel[0]: MAC Framework successfully initialized
    Nov 10 21:39:58 localhost kernel[0]: using 7864 buffer headers and 4096 cluster IO buffer headers
    Nov 10 21:39:58 localhost kernel[0]: IOPCCard info: Intel PCIC probe: TI 1510 rev 00
    Nov 10 21:39:58 localhost kernel[0]: FireWire (OHCI) Apple ID 31 built-in now active, GUID 001124fffe75e670; max speed s800.
    Nov 10 21:39:58 localhost kernel[0]: mbinit: done
    Nov 10 21:39:58 localhost kernel[0]: Security auditing service present
    Nov 10 21:39:58 localhost kernel[0]: BSM auditing present
    Nov 10 21:39:58 localhost kernel[0]: rooting via boot-uuid from /chosen: BAD0DFF0-4023-381B-8C51-E904679A62CC
    Nov 10 21:39:58 localhost kernel[0]: Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
    Nov 10 21:39:58 localhost kernel[0]: Got boot device = IOService:/MacRISC2PE/pci@f4000000/AppleMacRiscPCI/ata-6@D/AppleKauaiATA/ATADev iceNub@0/AppleATADiskDriver/IOATABlockStorageDevice/IOBlockStorageDriver/ST91008 23A ST9100823A/IOApplePartitionScheme/Untitled@3
    Nov 10 21:39:58 localhost kernel[0]: BSD root: disk0s3, major 14, minor 2
    Nov 10 21:39:58 localhost kernel[0]: jnl: unknown-dev: replay_journal: from: 6728192 to: 4701696 (joffset 0x8601000)
    Nov 10 21:39:58 localhost kernel[0]: CSRHIDTransitionDriver::start []
    Nov 10 21:39:58 localhost kernel[0]: CSRHIDTransitionDriver::switchToHCIMode legacy
    Nov 10 21:39:58 localhost kernel[0]: USBF: 22.539 CSRHIDTransitionDriver[0x2a10f00](IOUSBCompositeDevice) GetFullConfigDescriptor(0) returned NULL
    Nov 10 21:39:58 localhost kernel[0]: CSRHIDTransitionDriver... done
    Nov 10 21:39:58 localhost kernel[0]: E:[AppleUSBBluetoothHCIController][FindInterfaces] mInt0InterruptMaxPacketSize = 16
    Nov 10 21:39:58 localhost kernel[0]: jnl: unknown-dev: journal replay done.
    Nov 10 21:39:58 localhost kernel[0]: HFS: Removed 5 orphaned unlinked files or directories
    Nov 10 21:39:58 localhost kernel[0]: Jettisoning kernel linker.
    Nov 10 21:39:58 localhost rpc.statd[22]: statd.notify - no notifications needed
    Nov 10 21:39:59 localhost bootlog[39]: BOOT_TIME: 1194730773 0
    Nov 10 21:40:00 localhost kernel[0]: Resetting IOCatalogue.
    Nov 10 21:40:00 localhost kextd[12]: 0 cached, 423 uncached personalities to catalog
    Nov 10 21:40:08 localhost DirectoryService[35]: Launched version 5.0 (v514)
    Nov 10 21:40:08 localhost /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[27]: Login Window Application Started
    Nov 10 21:40:08 localhost DirectoryService[35]: WARNING - dsTouch: file was asked to be opened </Library/Preferences/DirectoryService/.DSIsRunning>: (File exists)
    Nov 10 21:40:09 localhost kernel[0]: UniNEnet: Ethernet address 00:11:24:75:e6:70
    Nov 10 21:40:09 localhost blued[50]: Apple Bluetooth daemon started.
    Nov 10 21:40:11 localhost /usr/sbin/ocspd[55]: starting
    Nov 10 21:40:11 localhost ifcstart[29]: 3891612: (CGSLookupServerRootPort) Untrusted apps are not allowed to connect to or launch Window Server before login.
    Nov 10 21:40:11 localhost com.apple.IFCStart[29]: Sat Nov 10 21:40:11 localhost ifcstart[29] <Warning>: 3891612: (CGSLookupServerRootPort) Untrusted apps are not allowed to connect to or launch Window Server before login.
    Nov 10 21:40:11 localhost ifcstart[29]: kCGErrorRangeCheck : On-demand launch of the Window Server is allowed for root user only.
    Nov 10 21:40:11 localhost com.apple.IFCStart[29]: Sat Nov 10 21:40:11 localhost ifcstart[29] <Error>: kCGErrorRangeCheck : On-demand launch of the Window Server is allowed for root user only.
    Nov 10 21:40:11 localhost ifcstart[29]: kCGErrorRangeCheck : Set a breakpoint at CGErrorBreakpoint() to catch errors as they are returned
    Nov 10 21:40:11 localhost com.apple.IFCStart[29]: Sat Nov 10 21:40:11 localhost ifcstart[29] <Error>: kCGErrorRangeCheck : Set a breakpoint at CGErrorBreakpoint() to catch errors as they are returned
    Nov 10 21:40:11 localhost /usr/libexec/ifcstart[29]: _RegisterApplication(), FAILED TO establish the default connection to the WindowServer, _CGSDefaultConnection() is NULL.
    Nov 10 21:40:11 localhost com.apple.IFCStart[29]: _RegisterApplication(), FAILED TO establish the default connection to the WindowServer, _CGSDefaultConnection() is NULL.
    Nov 10 21:40:12 localhost mDNSResponder mDNSResponder-161.1 (Oct 11 2007 00:22:27)[26]: starting
    Nov 10 21:40:13 localhost mDNSResponder[26]: Adding registration domain jodrell.members.mac.com.
    Nov 10 21:40:20 localhost kernel[0]: Matching service count = 0
    Nov 10 21:40:21: --- last message repeated 5 times ---
    Nov 10 21:40:21 localhost kernel[0]: wl0: Broadcom BCM4320 802.11 Wireless Controller
    Nov 10 21:40:21 localhost kernel[0]: 4.170.25.8.2
    Nov 10 21:40:21 localhost kernel[0]: AirPort_Brcm43xx: Ethernet address 00:11:24:8e:52:78
    Nov 10 21:40:21 Macintosh configd[37]: setting hostname to "Macintosh.local"
    Nov 10 21:40:22 Macintosh configd[37]: ipconfigd: method requires address and mask
    Nov 10 21:40:26 Macintosh kernel[0]: SetCryptoKey T: len 16, idx 0
    Nov 10 21:40:26 Macintosh configd[37]: AppleTalk startup
    Nov 10 21:40:26 Macintosh kernel[0]: SetCryptoKey R: len 16, idx 1
    Nov 10 21:40:27 Macintosh SystemStarter[19]: "/System/Library/StartupItems/NMPCCardOption3gDaemonVF" failed security check: world writable
    Nov 10 21:40:27 Macintosh SystemStarter[19]: "/System/Library/StartupItems/NMPCCardOption3gDaemonVF" failed security check: group writable
    Nov 10 21:40:27 Macintosh SystemStarter[19]: "/System/Library/StartupItems/NMPCCardOption3gDaemonVF" failed security check: not owned by UID 0
    Nov 10 21:40:27 Macintosh com.apple.SystemStarter[19]: Starting MySQL database server
    Nov 10 21:40:27 Macintosh com.apple.SystemStarter[19]: Starting Cisco Systems VPN Driver
    Nov 10 21:40:27 Macintosh com.apple.SystemStarter[19]: Tuning TCP/IP stack for 2.5G/3G performance
    Nov 10 21:40:27 Macintosh com.apple.SystemStarter[19]: kern.ipc.maxsockbuf: 8388608 -> 1048576
    Nov 10 21:40:27 Macintosh com.apple.SystemStarter[19]: Starting NMPCCardDaemonVMC
    Nov 10 21:40:27 Macintosh com.apple.SystemStarter[19]: Starting NMPPPMonitor
    Nov 10 21:40:27 Macintosh com.apple.SystemStarter[19]: net.inet.tcp.slowlink_wsize: 8192 -> 65535
    Nov 10 21:40:27 Macintosh com.apple.launchd[1] (0x10c1b0.nohup[102]): Could not setup Mach task special port 9: (os/kern) no access
    Nov 10 21:40:27 Macintosh /System/Library/StartupItems/NMPCCardDaemonVMC/NMPCCardDemonVMC[89]: Version 2.1.6 will start in 30 seconds.
    Nov 10 21:40:27 Macintosh com.apple.launchd[1] (0x10c1b0.nohup[104]): Could not setup Mach task special port 9: (os/kern) no access
    Nov 10 21:40:27 Macintosh com.apple.launchd[1] (0x10c1b0.nohup[112]): Could not setup Mach task special port 9: (os/kern) no access
    Nov 10 21:40:28 Macintosh com.apple.SystemStarter[19]: kextload: extension /System/Library/Extensions/CiscoVPN.kext is already loaded
    Nov 10 21:40:28 Macintosh kernel[0]: CiscoVPN : attempting to attach to all available ethernet interfaces.
    Nov 10 21:40:28 Macintosh kernel[0]: CiscoVPN : interface: en1, filter attached.
    Nov 10 21:40:28 Macintosh kernel[0]: CiscoVPN : en1
    Nov 10 21:40:28 Macintosh kernel[0]: CiscoVPN : current MTU for en1 is 1500, saving it.
    Nov 10 21:40:28 Macintosh kernel[0]: CiscoVPN : interface: en0, filter attached.
    Nov 10 21:40:28 Macintosh kernel[0]: CiscoVPN : en0
    Nov 10 21:40:28 Macintosh kernel[0]: CiscoVPN : current MTU for en0 is 1500, saving it.
    Nov 10 21:40:28 Macintosh kernel[0]: CiscoVPN : loading cisco ipsec kernel module.
    Nov 10 21:40:32 Macintosh configd[37]: AppleTalk startup complete
    Nov 10 21:40:33 Macintosh loginwindow[27]: Login Window Started Security Agent
    Nov 10 21:40:36 Macintosh kextd[12]: writing kernel link data to /var/run/mach.sym
    Nov 10 21:40:42 Macintosh authorizationhost[124]: MechanismInvoke 0x130e00 retainCount 2
    Nov 10 21:40:42 Macintosh SecurityAgent[125]: MechanismInvoke 0x103e40 retainCount 1
    Nov 10 21:40:42 Macintosh SecurityAgent[125]: NSSecureTextFieldCell detected a field editor ((null)) that is not a NSTextView subclass designed to work with the cell. Ignoring...
    Nov 10 21:40:43 Macintosh SecurityAgent[125]: MechanismDestroy 0x103e40 retainCount 1
    Nov 10 21:40:43 Macintosh loginwindow[27]: Login Window - Returned from Security Agent
    Nov 10 21:40:43 Macintosh authorizationhost[124]: MechanismDestroy 0x130e00 retainCount 2
    Nov 10 21:40:43 Macintosh loginwindow[27]: USER_PROCESS: 27 console
    Nov 10 21:40:43 Macintosh com.apple.launchd[1] (com.apple.UserEventAgent-LoginWindow[119]): Exited: Terminated
    Nov 10 21:40:43 Macintosh com.apple.launchctl.Aqua[131]: launchctl: Couldn't stat("/etc/machinit_peruser.d"): No such file or directory
    Nov 10 21:40:58 Macintosh /System/Library/StartupItems/NMPCCardDaemonVMC/NMPCCardDemonVMC[89]: Starts...
    Nov 10 21:40:58 Macintosh /System/Library/StartupItems/NMPCCardDaemonVMC/NMPCCardDemonVMC[89]: Looking for supported device 'VMC3G pccard'...
    Nov 10 21:40:58 Macintosh /System/Library/StartupItems/NMPCCardDaemonVMC/NMPCCardDemonVMC[89]: Looking for supported device 'Fusion Lite Quad pccard'...
    Nov 10 21:40:58 Macintosh Dock[139]: _DESCRegisterDockExtraClient failed 268435459
    Nov 10 21:40:58 Macintosh /System/Library/StartupItems/NMPCCardDaemonVMC/NMPCCardDemonVMC[89]: Looking for supported device 'Novatel Merlin U740 pccard'...
    Nov 10 21:41:00: --- last message repeated 1 time ---
    Nov 10 21:40:58 Macintosh /System/Library/StartupItems/NMPCCardDaemonVMC/NMPCCardDemonVMC[89]: Looking for supported device 'Huawei DATA PCCard'...
    Nov 10 21:41:10 Macintosh Dock[139]: [QL ERROR] Generator database update takes too long... we will use what we currently have
    Nov 10 21:41:58 Macintosh mdworker[147]: CFPropertyListCreateFromXMLData(): Old-style plist parser: missing semicolon in dictionary.
    Nov 10 21:42:00 Macintosh mdworker[149]: CFPropertyListCreateFromXMLData(): Old-style plist parser: missing semicolon in dictionary.

  • MSE not responding

      Hi all
    I am currently having trouble adding an MSE to NCS.
    I get a message from the NCS to say that the MSE server will not respond when I try to add it.
    I have verified that the NCS has IP connectivity to the MSE by switching my laptop for the MSE and taking its IP address.
    I have also verifed that the service is running with the command /etc/init.d/msed status
    Starting MSE Platform, Waiting to check the status.
    MSE Platform is up, getting the status
    Server Config
    Product name: Cisco Mobility Service Engine
    Version: 7.0.201.204
    Hw Version: V01
    Hw Product Identifier: AIR-MSE-3310-K9
    Hw Serial Number: FTX1604M05C
    Use HTTP: false
    Legacy HTTPS: false
    Legacy Port: 8001
    Log Modules: -1
    Log Level: INFO
    Days to keep events: 2
    Session timeout in mins: 30
    DB backup in days: 2
    Services
    Service Name: Context Aware Service
    Service Version: 7.0.200.204
    Admin Status: Enabled
    Operation Status: Up
    Service Name: Wireless Intrusion Protection Service
    Service Version: 1.0.2077.0
    Admin Status: Enabled
    Operation Status: Up
    Server Monitor
    Server start time: Fri Jul 13 13:30:25 BST 2012
    Server current time: Fri Jul 13 13:31:06 BST 2012
    Server timezone: GB-Eire
    Server timezone offset: 0
    Restarts: 22
    Used Memory (bytes): 41991360
    Allocated Memory (bytes): 158859264
    Max Memory (bytes): 954466304
    DB virtual memory (kbytes): 0
    DB virtual memory limit (bytes): 0
    DB disk memory (bytes): 1913046656
    DB free size (kbytes): 0
    Context Aware Service
    Total Active Elements(Wireless Clients, Tags, Rogue APs, Rogue Clients, Interfer
    ers, Wired Clients): 0
    Active Wireless Clients: 0
    Active Tags: 0
    Active Rogue APs: 0
    Active Rogue Clients: 0
    Active Interferers: 0
    Active Wired Clients: 0
    Active Elements(Wireless Clients, Rogue APs, Rogue Clients, Interferers, Wired C
    lients, Tags) Limit: 1000
    Active Sessions: 0
    Wireless Clients Not Tracked due to the limiting: 0
    Tags Not Tracked due to the limiting: 0
    Rogue APs Not Tracked due to the limiting: 0
    Rogue Clients Not Tracked due to the limiting: 0
    Interferers Not Tracked due to the limiting: 0
    Wired Clients Not Tracked due to the limiting: 0
    Total Elements(Wireless Clients, Rogue APs, Rogue Clients, Interferers, Wired Cl
    ients) Not Tracked due to the limiting: 0
    Context Aware Sub Services
    Subservice Name: Aeroscout Tag Engine
    Admin Status: Disabled
    Operation Status: Down
    Subservice Name: Cisco Tag Engine
    Admin Status: Enabled
    Operation Status: Up
    [root@HS-SR1-MSE-1 ~]# /etc/init.d/msed status
    [root@HS-SR1-MSE-1 ~]# /etc/init.d/msed status
    STATUS:
    Starting MSE Platform, Waiting to check the status.
    MSE Platform is up, getting the status
    Server Config
    Product name: Cisco Mobility Service Engine
    Version: 7.0.201.204
    Hw Version: V01
    Hw Product Identifier: AIR-MSE-3310-K9
    Hw Serial Number: FTX1604M05C
    Use HTTP: false
    Legacy HTTPS: false
    Legacy Port: 8001
    Log Modules: -1
    Log Level: INFO
    Days to keep events: 2
    Session timeout in mins: 30
    DB backup in days: 2
    Services
    Service Name: Context Aware Service
    Service Version: 7.0.200.204
    Admin Status: Enabled
    Operation Status: Up
    Service Name: Wireless Intrusion Protection Service
    Service Version: 1.0.2077.0
    Admin Status: Enabled
    Operation Status: Up
    Server Monitor
    Server start time: Fri Jul 13 13:30:25 BST 2012
    Server current time: Fri Jul 13 13:41:33 BST 2012
    Server timezone: GB-Eire
    Server timezone offset: 0
    Restarts: 22
    Used Memory (bytes): 53046040
    Allocated Memory (bytes): 192217088
    Max Memory (bytes): 954466304
    DB virtual memory (kbytes): 0
    DB virtual memory limit (bytes): 0
    DB disk memory (bytes): 1913046656
    DB free size (kbytes): 0
    Context Aware Service
    Total Active Elements(Wireless Clients, Tags, Rogue APs, Rogue Clients, Interfer
    ers, Wired Clients): 0
    Active Wireless Clients: 0
    Active Tags: 0
    Active Rogue APs: 0
    Active Rogue Clients: 0
    Active Interferers: 0
    Active Wired Clients: 0
    Active Elements(Wireless Clients, Rogue APs, Rogue Clients, Interferers, Wired C
    lients, Tags) Limit: 1000
    Active Sessions: 0
    Wireless Clients Not Tracked due to the limiting: 0
    Tags Not Tracked due to the limiting: 0
    Rogue APs Not Tracked due to the limiting: 0
    Rogue Clients Not Tracked due to the limiting: 0
    Interferers Not Tracked due to the limiting: 0
    Wired Clients Not Tracked due to the limiting: 0
    Total Elements(Wireless Clients, Rogue APs, Rogue Clients, Interferers, Wired Cl
    ients) Not Tracked due to the limiting: 0
    Context Aware Sub Services
    Subservice Name: Aeroscout Tag Engine
    Admin Status: Disabled
    Operation Status: Down
    Subservice Name: Cisco Tag Engine
    Admin Status: Enabled
    Operation Status: Up
    Has anybody else experienced these problems that can help, or could someone help with trouble shooting it.
    Many Thanks
    Simon

    When you said this:
    I have verified that the NCS has IP connectivity to the MSE by switching my laptop for the MSE and taking its IP address.
    Are you saying that when the MSE is connected you can't ping the MSE from the WCS or vice versa? Can you ping the gateway of the MSE when consoled from the MSE? The issue with the MSE is that depending on what network port the MSE brings up first during the boot up, that will be the active interface. Also the mse script does not work too well. After you run the initial script in the MSE you need to restart the network services.
    /etc/init.d/network restart
    Enter the following commands after you complete the startup wizard. This is an example. You will hard set your gateway and the Mac address to eth0 port. This way eth0 will have that ip address all the time and the OS will not have a decision on what interface will have that ip address.
    /etc/init.d/network restart
    echo GATEWAY=10.7.6.1 >> /etc/sysconfig/network-scripts/ifcfg-eth0
    echo HWADDR=00:1E:67:15:B8:59 >> /etc/sysconfig/network-scripts/ifcfg-eth0
    ifconfig eth0
    Verify the configuration for eth0
    Check system status
    start|stop|restart|reload|status
    /etc/init.d/msed status
    Sent from Cisco Technical Support iPhone App

  • WLC is not responding to SNMP requests.

    Customer is using a 4400 WLC.
    He has a management tool that works using the SNMP logs from the controller, he can ping the
    controller using this management tool, but when he sends SNMP requests from the management tool the
    WLC doesn't reply.
    The SNMP server IP address is 192.168.122.11 and the WLC's IP address is  10.20.1.31.
    I have the following debug taken from the switchport where the WLC is connected.
    'debug snmp agent' shows some interesting messages that confirms that the WLC is not sending a packet back.
    Cisco Controller) >debug  snmp agent enable
    (Cisco Controller) >*SNMPTask: Feb 06 14:38:44.616: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 59
    *SNMPTask: Feb 06 14:38:44.616: SNMPD: Failed to build in SnmpMessage.
    1145 Debug Messages have been dropped*SNMPTask: Feb 06 14:38:44.616: SNMPD: *NOT* sending out packet, out_packet_len = 0
    *SNMPTask: Feb 06 14:38:47.621: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 59
    *SNMPTask: Feb 06 14:38:47.621: SNMPD: Failed to build in SnmpMessage.
    *SNMPTask: Feb 06 14:38:47.621: SNMPD: *NOT* sending out packet, out_packet_len = 0
    *SNMPTask: Feb 06 14:38:50.652: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 59
    *SNMPTask: Feb 06 14:38:50.652: SNMPD: Failed to build in SnmpMessage.
    *SNMPTask: Feb 06 14:38:50.652: SNMPD: *NOT* sending out packet, out_packet_len = 0
    *SNMPTask: Feb 06 14:38:53.684: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 50
    *SNMPTask: Feb 06 14:38:53.684: SNMPD: Failed to build in SnmpMessage.
    *SNMPTask: Feb 06 14:38:53.684: SNMPD: *NOT* sending out packet, out_packet_len = 0
    *SNMPTask: Feb 06 14:38:56.715: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 50
    *SNMPTask: Feb 06 14:38:56.715: SNMPD: Failed to build in SnmpMessage.
    *SNMPTask: Feb 06 14:38:56.715: SNMPD: *NOT* sending out packet, out_packet_len = 0
    *SNMPTask: Feb 06 14:38:59.747: SNMPD: Packet from: 192.168.122.11:2509, in_packet_len = 50
    *SNMPTask: Feb 06 14:38:59.747: SNMPD: Failed to build in SnmpMessage.
    *SNMPTask: Feb 06 14:38:59.747: SNMPD: *NOT* sending out packet, out_packet_len = 0
    I have also a packet capture taken from the same switchport, I attach it here.
    What could be the reason for not responding?

    You need to add the management tool in the WLC as a trap reciever.
    Thanks,
    Scott
    *****Help out other by using the rating system and marking answered questions as "Answered"*****

Maybe you are looking for

  • Problem in NSU 1.2.20en

    hello all, hereby, I am newbie in nokia software updater. I am user of nokia n70. here some information about my phone : Nokia N70-1 V 2.0536.0.2 12-09-05 RM-84 code : 0524118 the problem is, my nsu hang at starting application, I tried to wait almos

  • Import Files to Final Cut Pro X

    Hi I wanted to know if there is any way to import .avi's or .MTS's to Final Cut Pro X or if there is any special software I need. The .avi if coming from Dxtory, a windows program (http://dxtory.com/v2-home-en.html), and the .MTS is coming from an AV

  • Asset Purchase Requisition

    Hello, I would like to know what is the correct process of creating an asset purchase requisition. How does a user open a requisition for an asset (which has not been created yet) ? It makes sense that he actually has to request for the creation of a

  • Only one app asks for wrong id

    my mac book keeps asking me to update my imovies which i would but my mothers id comes up and does not let me delete id and put mine in why can i not delete it and update it. i updated my mums phone on this mac book pro as she didnt now how to why wo

  • Combine iPhoto library with two sessions.

    On my new iMac, I made tree sessions and would like to combine the iPhoto library with two, non Admin sessions. Is this possible? Thanks