CISCO WAP4410N/CISCO AP 541N

Can any one help me if we compare the 2 AP Which one is better .
if we not consider the cluster function of ap541n.
i got some info from blog the device wap 4410n got hanged .
Thanks,
Saroj

HI Eric Moyers,
I have seen iN Some Cisco Datasheets,and i Came to know that these Accesspoints Operate in Both BAnds.But as per your documentation wap4410 N Operates in Singal Band such as 2.4 GHZ, but which i followed the datasheet, in that These Accesspoints operate in Both The Frequency Bands. Culd you please remove this Confusion.
Below is red marked for your reference.
http://www.cisco.com/en/US/products/ps10047/prod_models_comparison.html.
RAM Installed ( Max )
64 MB
N/A
Flash Memory Installed (Max)
32 MB
N/A
Hard Drive
None.
None.
Networking
Form Factor
External
External
Connectivity Technology
Wireless
Wireless
Data Transfer Rate
300 Mbps
300 Mbps
Data Link Protocol
IEEE 802.11b, IEEE 802.11a, IEEE 802.11g, IEEE 802.11n (draft 2.0)
IEEE 802.11b, IEEE 802.11g, IEEE 802.11n (draft)
Spread Spectrum Method
OFDM, DSSS
OFDM, DSSS
Remote Management Protocol
SNMP 1, SNMP 2, SNMP 3
SNMP 1, SNMP 2c, HTTP, HTTPS
Frequency Band
2.4 GHz, 5 GHz
2.4 GHz, 5 GHz
Status Indicators
Port status, port transmission speed, power
Link activity, power, link OK
Features
DHCP support, load balancing, VLAN support, Syslog support, firmware upgradable, MIMO technology, Wi-Fi Multimedia (WMM) support, Quality of Service (QoS), wireless bridge mode, clustering technology
DHCP support, power over Ethernet (PoE), load balancing, VLAN support, Syslog support, E-mail alert, MAC address filtering, IPv6 support, Wireless Distribution System (WDS) support, firmware upgradable, MIMO technology, Spanning Tree Protocol (STP) support, Wi-Fi Multimedia (WMM) support, event log, Quality of Service (QoS), RADIUS support, Wi-Fi Protected Setup (WPS), wireless bridge mode
Encryption Algorithm
64-bit WEP, WPA-PSK, 128-bit AES, WPA2-PSK, WPA-Enterprise, WPA2-Enterprise
128-bit WEP, 64-bit WEP, WPA, WPA-PSK, WPA2-PSK, WPA-Enterprise, WPA2-Enterprise
Authentication Method
RADIUS, Basic Service Set Identifier (BSSID)
RADIUS, Radio Service Set ID (SSID), Basic Service Set Identifier (BSSID)
Compliant Standards
IEEE 802.3, IEEE 802.3u, IEEE 802.1D, IEEE 802.1Q, IEEE 802.11b, IEEE 802.11a, IEEE 802.3af, IEEE 802.11d, IEEE 802.11g, IEEE 802.1x, IEEE 802.11i, Wi-Fi CERTIFIED, IEEE 802.11n (draft 2.0)
IEEE 802.3, IEEE 802.3u, IEEE 802.1Q, IEEE 802.1p, IEEE 802.11b, IEEE 802.3af, IEEE 802.11d, IEEE 802.11g, IEEE 802.1x, IEEE 802.11i, IEEE 802.11n (draft), Wi-Fi Protected Setup
Line Coding Format
N/A
OFDM
Network / Transport Protocol
N/A
DHCP
Antenna
Antenna
External detachable
External detachable
Antenna Qty
3
3
Directivity
Omni-directional
Omni-directional
Gain Level
2 dBi
2 dBi
Expansion / Connectivity
Interfaces
1 x network / power - Ethernet 10Base-T/100Base-TX/1000Base-T - RJ-45
1 x network / power - Ethernet 10Base-T/100Base-TX/1000Base-T - RJ-45
Miscellaneous
Cables Included
1 x network cable
1 x network cable
Compliant Standards
CE, EN 300.328, EN 301.489.1, EN 301.489.17, RSS-210, IC, ICES-003 Class A, FCC, UL 60950-1, IEC 60950-1, EN 60950-1, AS/NZS 4268, EN 301.893
CE, IC, FCC
Power
Power Over Ethernet (PoE) Supported
Yes
Yes
Power Device
Power adapter - external
Power adapter - external
Voltage Required
AC 120/230 V ( 50/60 Hz )
N/A
Software / System Requirements
OS Provided
Linux
Linux
Manufacturer Warranty
Service & Support
Limited lifetime warranty
3 years warranty
Service & Support Details
Limited warranty - replacement - lifetime
Limited warranty - replacement - 3 years,
New releases update - 90 days,
Technical support - phone consulting - 1 year
Environmental Parameters
Min Operating Temperature
32 °F
32 °F
Max Operating Temperature
104 °F
104 °F
Humidity Range Operating
10 - 85%
10 - 85%
Product Image
AP541N
WAP4410N
Regards,
Prakash@CIL.

Similar Messages

Cisco AP 541N

Hello all
I am trying to configure the the PA for guest and secure local access. I am unsure on how to accomplish this on the AP541N Dual Band Single Radio AP. Is there a document out there.
This is what I would like to do
Guess comes in and be able to horseshoe out to the internet via WEP
Local network user who are mobile should be able to connect to the other secure SSID using WPA2 to the internal network

Hi,
Below links could be of some help :
Admin guide : http://www.cisco.com/en/US/docs/wireless/access_point/csbap/AP541N/administration/guide/AP541Nadmin.pdf
Quick start guide : http://www.cisco.com/en/US/docs/wireless/access_point/csbap/AP541N/quick_start/guide/AP541N_QSG.pdf
Regards,
Madhuri

Any new firmware for the Cisco AP541N access points.

Do you know if Cisco has come out with any new firmware for the Cisco AP541N access points.

Latest release is 1.8.0 from Jan 25, 2010:
http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=1.8.0&mdfid=282790482&sftType=Small+Business+Pro+Wireless+Software&optPlat=&nodecount=2&edesignator=null&modelName=Cisco+AP+541N+Wireless+Access+Point&treeMdfId=278875243&treeName=Wireless&modifmdfid=null&imname=&hybrid=null&imst=null&lr=Y

Cisco 526 controller and AP541N

Hello,
I have a cisco 526 controller. Since this device is EOL. Can I still use 526 controller with AP541N? What are the limitations and problem configuring with
AP541N?
Thanks.
Dipendra

Hi Dipendra,
The 541N is NOT supported via the 526 Controller
With the Cisco AP 541N, you can:
• Easily set up, configure, and manage multiple wireless access points, without the need to invest in a wireless controller
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10492/data_sheet_c78-566239.html
Cheers!
Rob

Firmware for the Cisco 3G Wireless HWIC

Is it FW K2.0.7.19 compatible with EHWIC-3G-HSPA+7?

Latest release is 1.8.0 from Jan 25, 2010:
http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=1.8.0&mdfid=282790482&sftType=Small+Business+Pro+Wireless+Software&optPlat=&nodecount=2&edesignator=null&modelName=Cisco+AP+541N+Wireless+Access+Point&treeMdfId=278875243&treeName=Wireless&modifmdfid=null&imname=&hybrid=null&imst=null&lr=Y

AP 541N - Problems with Clustering Function

Hi,
we have got 3 Cisco APs 541N with firmware version 9.2.2 and want to set up the cluster function for those APs.
Here is the problem:
Before enabling the cluster you can ping all three APs located in the same local network with a delay of 1ms or below.
If the cluster is enabled the pings for one AP rise above 200 ms in a random way (see attached file).
Moreover users connected to that AP are more likely to lose the connection or experience delay.
Do the APs communicate through LAN or WLAN ?
Does anyone know what could be the cause of the problem?
Thanks.
Regards Richard

Hi NIC, the clusters communicate through the WLAN (a poe switch is not required for network connectivity). Looking at the ping, this seems pretty normal. Most of the time as 1 ms and a few spike up. You may even see 1 packet drop out of every 100-200. Which is also normal.
If you feel there is a problem, you may not be getting a weak enough signal to fall to the next device, therefore, sort of hitting a void zone where your signal is good enough to hold on to the original connection but not weak enough to resume on the closest vicinity AP.
You can try to test this theory by moving to close proximity of each AP, disconnect from the wireless and reconnect. Ultimately, I think you will see the same behavior.
If you feel it is firmware related, since the 9.2.0.2 was released April of this year, try the previous release and test this. However, I don't feel it is a firmware issue, since I've had these working fine in the previous months with up to 8 devices at customer premises.
http://www.cisco.com/cisco/software/release.html?mdfid=282790482&flowid=&softwareid=282804210&os=null&release=2.0.1&relind=null&rellifecycle=null&reltype=null
-Tom
Please rate helpful posts

Cisco linksys WAP4410N WPS problem

dear all
i have two AP i set one as AP mode and another as WDS repeater
i disable WPS via ssh ad when i see wi-fi protected setup wps shown disabled
the problem until now when some body try to connect to the AP there is a message shown that addtional logon required
how can i solve this so any one can connect with no need only for wifi pass
in past i set the first ssid as default and not broadcast it and create second ssid that i can broadcast it
now i cannot only broadcast one ssid because the mode AP with alowed some repeaters
firmware version
2.0.6.1

Please check the below video link which can helpful for you in configuration:
Link-1: http://www.youtube.com/watch?v=C96Gdd_18G0
Link-2:
http://www.cisco.com/en/US/docs/wireless/access_point/csbap/wap4410n/administration/guide/WAP4410N_Admin_Guide.pdf

Attach WAP4410N as WGB to Cisco 5760 WLC with LWAP 3702

I have 5760 WLC with 3702 wireless infrastructure. Can i connect a WAP4410N AP as WGB to be attached to my current wifi network so i can provide connectivity to some wired devices? Any tips on doing so? And any limitation can be imposed for using this WAP instead of any other AP that are supported by WLC5760? If the wired clients are passive, configuring passive-client on WLC will work normally?

Thanks Eric for the reply, however, this AP is not expected to be controlled by WLC as you mentioned since it is not lightweight and not supported by this WLC for compatibility. But in this scenario, i'm talking about operating it in WGB mode to be attached to the unified wireless infrastructure. In this scenario, it is just attached as a client that pass the traffic of its clients to the other side.
I have noticed the below statement in this guide page (539)
http://hcsdemo.com/c/en/us/td/docs/switches/lan/catalyst3650/software/release/37e/consolidated_guide/b_37e_consolidated_3650_cg.pdf
When non-Cisco WGBs are used, the switch has no information about the IP address of the clients on the wired segment behind the WGB. Without this information, the switch drops the following types of messages:
• ARP REQ from the distribution system for the WGB client.
• ARP RPLY from the WGB client.
• DHCP REQ from the WGB client.
• DHCP RPLY for the WGB client.
Accordingly, if the switch will drop all this traffic, then no traffic will be passed from the WGB clients to the network ! what I’m missing here?!!!

Linksys E1200 Connecting with Cisco WAP4410n Wirelssly

I have a Linksys E1200 Wifi Router which is connected on LAN Port 1 with Switch. I have enable DHCP through my Server with Internet Connection Sharing.
Now I want to expand my wireless range with 5 WAP4410n in a building.
Can I connect Cisco WAP4410n with E1200 Router? If yes then what will be the WAP4410n AP Mode?
How can I Connect all 5 APs' with same SSID to expand my wireless range?
Moreover, I can access easily to Linksys E1200 on my machines easily within the range but I want to expand the range without the cable.

You might post a direct link to this forum or particular thread if there is informaton on it available.
Jcol wrote:
Hi! I actually have a similar concern with my Ciscobusiness class device before, but I went to a different forum. Try community.cisco.com and I think they have the answers to your question. Hope this helps!

CISCO WAP4410N Access Point disconnect after a short while

Dear Sir,
i bought one access point then we configured as Wireless Client/Repeater but wireless connection disconnecting and connecting after a short while
i tried 4 more different ADSL and different IP range ADSL model showing same.
so please advice on this matter ASAP.
Thanks.
Rahmath.CK

My name Eric Moyers. I am an Engineer in the Small Business Support Center.
I am sorry that no one has responded before now. What is the router that you are trying to repeat?
What were the steps you went through to do this?
According to the Admin Guide for the WAP4410N it will only repeat the WRVS4400N and another WAP4410N.
Eric Moyers
.:|:.:|:. CISCO | Cisco Presales Technical Support | Wireless Subject Matter Expert
Please rate helpful Posts and Let others know when your Question has been answered.

Does anyone know of a phone tech service that can help me set up my Cisco WAP4410N pre-owned router?

I am not a tech personality and need a bit of hand holding in setting up my WAP4410N device. My old router Linksys 1500 seems to be having dropping signal issues and I purchased this WAP4410N online to replace it. I need to know if I made the right choice in the purchase and how to set it up.
Tony

Hello,
I'm a Cisco Engineer and I'm sorry, I don't have a phone number to give you but I actually replied to this post to clarify something:
The WAP4410N is not a router, it is just an Access Point, so if you are trying to replace a router, this is really not the right device. As you can see this unit has a single port on the back as opposed to 4 LAN ports and 1 Internet port.
If you are correct o the model number then my advice is for you to look for another device, an actual router so that you can replace your Linksys unit.
I hope this was helpful

Necesito configurar un Cisco sb WAP4410N

Necesito configurar un Cisco sb WAP4410N y no se cual es el usuario y clave por defecto en el sshh. He probado con admin-admin o cisco-cisco y nada. Estoy usando la ultima version del Cisco SDM. Gracias de antemano.

You will get solution at this link please follow this:
https://supportforums.cisco.com/discussion/11176981/wap-4410-n-setup

Does Cisco WAP4410N work as repeater for Linksys E4200 ?

Does Cisco WAP4410N work as repeater for Linksys E4200 ?
Hi,
i have Linksys E4200 and I need repeater for it ...
Can anybody help me with this issue ?
BR

Thx for answer
I tested it and it works as Wireless Client - computer connected by ethernet wire is OK, everything works (DHCP etc)
but when i turn on " Allow wireless station to associate" in WAP4410N settings of "Wireless Client/Repeater" it doesn't work at all
I mean clients on wireless side and on wire side too ( DHCP doesnt work , there is no communication )

Cisco WAP4410N - not configurable as Wireless Client with WRT610N?

Hi!
On several workstations I use multiple network to
1 - access Internet and share Printers
2 - communicate within the local area
The second WLAN I need for several NDAS devices.
Due to their own LPX-Protocol these NDAS devices don't work properly with MAC address cloning. In combination with several access points or clients from other manufacturers Wireless N transmission does not work.
So in WLAN 2 I use the Cisco Linksys WRT 610N Router with 2.4 Ghz WLAN.
I intended to use the Cisco WAP4410N in Client Mode to connect a workstation with this router and set up NDAS connection.
Other workstations will directly connect to the router via Cisco Linksys WUSB-600N.
The connection from WUSB-600N to WRT610N works perfectly.
My problem is:
The WAP4410N does not connect to a wireless Network in Client Mode.
(It is not a problem of Channel configuration, Security or Signal strength - because if I connect my workstation via WUSB-600 this works instantly.)
If setup as an access Point it will start up sending competing to my router.
In Network Status it shows no received packages.
In Wireless Client/Repeater Mode there is no connection either.
My question is:
Is the WAP4410N not designed to be used as a Wireless Client?
An if it was - how is it to be set up as one?
Thanks
ando_user

Hi!
On several workstations I use multiple network to
1 - access Internet and share Printers
2 - communicate within the local area
The second WLAN I need for several NDAS devices.
Due to their own LPX-Protocol these NDAS devices don't work properly with MAC address cloning. In combination with several access points or clients from other manufacturers Wireless N transmission does not work.
So in WLAN 2 I use the Cisco Linksys WRT 610N Router with 2.4 Ghz WLAN.
I intended to use the Cisco WAP4410N in Client Mode to connect a workstation with this router and set up NDAS connection.
Other workstations will directly connect to the router via Cisco Linksys WUSB-600N.
The connection from WUSB-600N to WRT610N works perfectly.
My problem is:
The WAP4410N does not connect to a wireless Network in Client Mode.
(It is not a problem of Channel configuration, Security or Signal strength - because if I connect my workstation via WUSB-600 this works instantly.)
If setup as an access Point it will start up sending competing to my router.
In Network Status it shows no received packages.
In Wireless Client/Repeater Mode there is no connection either.
My question is:
Is the WAP4410N not designed to be used as a Wireless Client?
An if it was - how is it to be set up as one?
Thanks
ando_user

ASA5505 And Cisco WAP4410N

Hello,
A couple of days ago, my old access point burned out. It was a proxim ap-700. Anyway, I bought a new ap and recieve it today. I have been having trouble getting it up and going. I was wondering if anybody might have any idea what I'm messing up on.
Now the 5505 has already been configured for dmz, ip 10.10.10.1/24, vlan id 13--- But when I try to input information into the ap and save it from it being connected to my laptop.. Then after that I unplug it and plug it into my 5505 in the same port as the other dead ap was in... It takes a long time to connect to it, then when I do.... I can't connect to the Internet or anything.
ip: 10.10.10.245
sub: 255.255.255.0
gate: 10.10.10.1
dns1: 8.8.8.8
dns2 8.8.4.4

Yes, I'm sure.
I followed these steps to get it going. But I'm faced with something stupid... I can connect to the ap and it says I have Internet, but when I try to go to google or anything, my browser tells me it can't connect.
I'm trying to figure out what happened.
http://www.mailbeyond.com/adding-dmz-to-cisco-asa5505
Link I used to figure most of it out..

CISCO WAP4410N/CISCO AP 541N

Similar Messages

Maybe you are looking for