Cisco WCS --- Load threat violation

Hi ,
I need a WCS report that will actually give me the top n Wireless Access points that have too many clients trying to authenticte to them. We have some serious capacity issue in meeting rooms but we need figure of how many WAPs might be affected.   I know I can interogate the WCS to drill down and find out that WAPs are exceeding their threshold I just need to have a decent report ...

Problem : Too many clients associated with this radio interface
Solution:
1) Verify the clients counts on this radio interface. If the threshold for this trap is too low, you may need to re-adjust it.
2)Add new capacity  to the physical loaction  if the clients counts is a frequency issue on this radio
I got guys.. ;-)

Similar Messages

  • What does Load threshold violation reported by '802.11b/g' mean?

    I am assuming it is too many laptops on an access point. This environment has 24 laptops on a cart used in 1 room so shouldn't the controler divy them up between the 2 antennas  in the 1142 which is sitting right above them?
    thanks
    Gary

    Hi Gary,
    Just to add a note here to the good info from my friend Leo (+5 ponts L-Man)
    You are most correct about the nature of this alarm;
    WCS Message AP ''{0}'', interface ''{1}." Load threshold violated.
    Symptoms A radio interface of an access point is reporting that the client load has
    crossed a configured threshold.
    WCS Severity Minor.
    Probable Causes There are too many clients associated with this radio interface.
    Recommended Actions Verify the client count on this radio interface. If the threshold for this
    trap is too low, you may need to readjust it.
    Add new capacity to the physical location if the client count is a frequent
    issue on this radio.
    As Leo noted, the dual antennas in "Diversity" mode won't help to mitigate
    this issue. Only adding another AP can help load balance the client load
    Cheers!
    Rob
    Please support CSC Helps Haiti
    https://supportforums.cisco.com/docs/DOC-8895
    https://supportforums.cisco.com/docs/DOC-8727

  • Load threshold violation

    I see many "Load threshold violation" messages in NCS server. any idea why and how can i fix it?

    Thresholds are usually set on the WLC. Its up to you to leave it at default or you can adjust that.
    Sent from Cisco Technical Support iPad App

  • Load threshold violation - gap in voice audio

    Hello,
    I have a lot of 7925 Phones, two 3750 with integrated WLC (6.0.188).
    The Costumer says that he has a lot of gaps in voice audio. I have testet it and can't recognize any gap.
    I said to the customer that he has to write down the time when there are any problems with the audio stream.
    I could recognize that there is a minor alarm in the wcs at the same time when the problems occur.
    I could also see in the log of the ap that there is an reset of the a radio after the alarm is generated
    The WCS Error message is
    Load threshold violation reported by '802.11a' interface of AP 'AP-DE-HQ-033', connected to Controller.....
    What could be the reason of these error message? Wich kind of treshold is meant and where i can configure it.
    I hope someone can help me

    Sir,
         The load threshold violation is generated because of client count on a given AP, I am not aware of any bugs or features that would cause this to occurr in correctly. basically this alarm is triggered when the client count exceeds the preset threshold value which I believe is 12. You can find this threshold under Wireless> 802.11a> RRM>General (on WLC 6.0.118.0 code, it'll be in the same general area on 4.2; Don't confuse it with the coverage hole threshold which is usually 3).  Definitely check the client counts on the access points have the issues.
         If you are violating this threshold there are a couple of options:  1) raise the threshold to a higher value; the downside to this is if you get too many clients on a single AP it can have adverse effects on all the clients.  2) add more access points to lower the possibility of all clients being on 1 AP..
    Hope this helps,
    Kayle

  • Error Message - java.lang.LinkageError: loader constraint violation

    Hi
    I get the following errormessage if I try to apply a more recent build of the JPA Toplink Essentials.
    If I use the glassfish-persistence-installer-v2-b45.jar all things work fine, but if a try to upgrade my program will fail. I tried the glassfish-persistence-installer-v2-b54.jar, all also tried all builds between?!
    I have no idea how I may resolve the problem?!
    Any ideas?
    Thanks
    Marcel
    (I am using Java 6, Netbeans 5.5)
    Exception in thread "AWT-EventQueue-0" java.lang.LinkageError: loader constraint violation in interface itable initialization: when resolving method "DatenStruktur.ConditionBasic.getCouplingElement()LDatenStruktur/CouplingElement;" the class loader (instance of oracle/toplink/essentials/internal/ejb/cmp3/JavaSECMPInitializer$TempEntityLoader) of the current class, DatenStruktur/ConditionBasic, and the class loader (instance of sun/misc/Launcher$AppClassLoader) for interface DatenStruktur/Conditionable have different Class objects for the type DatenStruktur/CouplingElement used in the signature
    at java.lang.Class.getDeclaredFields0(Native Method)
    at java.lang.Class.privateGetDeclaredFields(Class.java:2291)
    at java.lang.Class.getDeclaredFields(Class.java:1743)
    at oracle.toplink.essentials.internal.security.PrivilegedAccessHelper.getDeclaredFields(PrivilegedAccessHelper.java:204)
    at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataHelper.getFields(MetadataHelper.java:443)
    at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataDescriptor.usesPropertyAccess(MetadataDescriptor.java:1081)
    at oracle.toplink.essentials.internal.ejb.cmp3.metadata.accessors.ClassAccessor.processAccessors(ClassAccessor.java:564)
    at oracle.toplink.essentials.internal.ejb.cmp3.metadata.accessors.ClassAccessor.process(ClassAccessor.java:498)
    at oracle.toplink.essentials.internal.ejb.cmp3.metadata.accessors.MetadataAccessor.processAccessor(MetadataAccessor.java:514)
    at oracle.toplink.essentials.internal.ejb.cmp3.metadata.accessors.ClassAccessor.processTableAndInheritance(ClassAccessor.java:1388)
    at oracle.toplink.essentials.internal.ejb.cmp3.metadata.accessors.ClassAccessor.process(ClassAccessor.java:484)
    at oracle.toplink.essentials.internal.ejb.cmp3.metadata.MetadataProcessor.processAnnotations(MetadataProcessor.java:240)
    at oracle.toplink.essentials.ejb.cmp3.persistence.PersistenceUnitProcessor.processORMetadata(PersistenceUnitProcessor.java:370)
    at oracle.toplink.essentials.internal.ejb.cmp3.EntityManagerSetupImpl.predeploy(EntityManagerSetupImpl.java:600)
    at oracle.toplink.essentials.internal.ejb.cmp3.JavaSECMPInitializer.callPredeploy(JavaSECMPInitializer.java:169)
    at oracle.toplink.essentials.internal.ejb.cmp3.JavaSECMPInitializer.initPersistenceUnits(JavaSECMPInitializer.java:237)
    at oracle.toplink.essentials.internal.ejb.cmp3.JavaSECMPInitializer.initialize(JavaSECMPInitializer.java:253)
    at oracle.toplink.essentials.ejb.cmp3.EntityManagerFactoryProvider.createEntityManagerFactory(EntityManagerFactoryProvider.java:140)
    at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java):96)
    at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java):73)
    at MainProgramManagement.ProgramMain.getEntityManagerFactory(ProgramMain.java:347)
    at MainProgramManagement.ProgramMain.persistData(ProgramMain.java:788)

    upgrade to cf8, which supports jdk 1.6.
    mx7 does not support 1.5 or 1.6
    Azadi Saryev
    Sabai-dee.com
    http://www.sabai-dee.com/

  • Cisco WCS integration with SNMP based monitoring

    I am looking for a solution to integrate Cisco WCS with any SNMP based monitoring solution.  My requirement is below,
    - Alerts for Access points up/down should be picked up by an alerting system in its console through SNMP.
    - I dont want all access points to be monitored, but only a critical group.
    Currently all access points are configured on LWAP mode under a wireless controller.  Can i configure APs individually for SNMP and get it monitored through the 3rd party monitoring tool.
    Can anyone please guide me to find a solution for this.

    http://www.cisco.com/en/US/docs/wireless/mse/3350/6.0/CAS/configuration/guide/msecg_ch2_CAS.html

  • Cisco WCS Date Format mm/dd/yyyy

    We have implemented Cisco WCS Guest Portal and when we create a new account for a visitor the date format is mm/dd/yyyy.
    Does anyone know if this can be changed to UK format: ddmm/yyyy??
    Thanks In advance for your replies.

    Hi Saurav
    Thanks for your reply but when I try to do search on bug on cisco.com, I got the following message.

  • Retrive load threshold violation reports using NCS 1.0.2.29?

    Hello!
    I would like to retrive some specific reports from the NCS regarding load threshold violation on some specific 1142N accesspoints. Using the alarm browser don´t help me that much because you cant see the history of how many alarms each AP has generated, only cleared alarms. The reason to this is that I would like to see if there is any issues in different system campus with APs that report this alarm.
    Most of the APs are associated to maps. The NCS version that I run is 1.0.2.29. WLCs are running 7.0.220.0.
    If there is any other way to see this information I´m happy to get that information.
    Thanks!
    /Johan Jongen

    Hello!
    I would like to retrive some specific reports from the NCS regarding load threshold violation on some specific 1142N accesspoints. Using the alarm browser don´t help me that much because you cant see the history of how many alarms each AP has generated, only cleared alarms. The reason to this is that I would like to see if there is any issues in different system campus with APs that report this alarm.
    Most of the APs are associated to maps. The NCS version that I run is 1.0.2.29. WLCs are running 7.0.220.0.
    If there is any other way to see this information I´m happy to get that information.
    Thanks!
    /Johan Jongen

  • Disabling the unlimited Lifetime option in Cisco WCS Guest User Creation

    Is there  a way to disable the unlimited Lifetime option in Cisco WCS Guest User Add/Schedule tab.If i make those fields uneditable, it just takes out the option to schedule any meetings in future.Using Cisco WCS version 7.0.220.0.

    i'm also searching for an solution to disable the unlimited lifetime button for the Lobby Ambassador.
    could it that Cisco introduces this maybe a future release?
    couldn't be that there are only few people who are disappointed with this solution.
    My Customer is thinking now that cisco isn't the right solution for him.

  • Using Cisco WCS with Microsoft IAS

    Hi.
    I have two 5508 and WCS 7.0.172. I want to user Active Directory users credintals to login on ther WCS. Have a configurated NPS role on server with windows 2008 r2.
    I have read this http://zmq503o1.wordpress.com/2008/01/06/using-cisco-wcs-with-microsoft-ias/ and done the same.
    I dont't agree with "on the "Encryption" tab and clear all the checkboxes except "No encryption" - wants an encryption connection but this didn't work till in user's properites in AD permit "Reversible encryption". This is not what that I want.  Would I need to generate ssl-cert for the wcs as wroted this?http://www.cisco.com/en/US/docs/wireless/wcs/7.0MR1/configuration/guide/hard.html#wp1042471
    or doing smth else? thx

    Camera is only supported for use with CUVA. Any other application attempting to utilize the camera is not tested and is not supported.

  • Java.lang.LinkageError: loader constraint violation

    I am using ToplinkEssentials as a persistence provider in a J2SE desktop application. I've encountered the following error.
    java.lang.LinkageError: loader constraint violation: loader (instance of sun/misc/Launcher$AppClassLoader) previously initiated loading for a different type with name "expendituretracking/Employee"
    I have unsuccessfully searched for a clue as to what is causing this problem. Any help is appreciated.

    Hello,
    Could this be related to the bug described at:
    https://glassfish.dev.java.net/issues/show_bug.cgi?id=2625
    If you have an interface involved, try adding them to the persistence.xml's list of classes.
    Best Regards,
    Chris

  • Cisco WCS and VMware

    I need to update my WCS server running VMware to the following:
    Cisco WCS can be run on VMware ESX Server 3.0.1 or later. The minimum hardware requirements for a dedicated and guaranteed VMware server are Intel? Xeon Quad CPU; 3.15 GHz, 8 GB RAM, 200 GB HDD.
    I would like to know is this only for the virtual server or must it be done on the host for complete Cisco support?
    Thx

    Hi,
    Here is it running on VMWare 3.01 on a quad-core Xeon with 16GB. We gave the server 2GB of memory. It uses 800Mhz CPU. We have about 60 Lwapp 1231 ap's and the wcs is a 4.0.179 version (need to upgrade ;-))

  • Cisco WCS Server unable to login

    Hi ,
    I have a Cisco WCS 4.x Server installed on Windows Server.I am not able to login to the WCS Server through Root username password. I have recover the root password through WCS password recovery procedure.After the password recovery i was able to login to the WCS and it started working with the new password.
    The problem repeats everytime.I have recovered password around 4 to 5 times and after some days again the same issue means i am not able to login to the server.
    I wanted to know whether the password gets expired automatically or is there any issue with the database due to which password gets reset automatically.
    One thing i have observed if i change the password through recovery procedure it works for some time and again after some days i am not able to login.
    Please advice me in this issue.
    Thanks & Regds,
    Lalit

    Hi,
    please do the password recovery and forward the log "wcs-0-0.log".
    Lets see from the logs!!
    Regards
    Surendra

  • Difference between cisco prime NCS and cisco WCS

    hello
    i have a question. I am just started with testing cisco prime ncs
    i have worked with cisco WCS
    now i was wondering wat the difference is between these two
    can someone please explain it.
    thanks allot

    They are both very similiar in functionality.  The major difference is that NCS offers a basic switch management front end and allows you to see your wired clients just as you would your wireless.  Other then that, the I've found the latest version of NCS to run quite a bit smoother and faster then my WCS install of several years, slicker graphics.  I would recommend using NCS in Chrome for the best view.

  • Want to change the hostname of cisco WCS on Windows

    Hi
    We have cisco WCS and by default hostname is nonwmonitor .
    Now we need to generate the certificate that will match with Hostname and so want to change the hostname.
    Please help me for providing the process to change the histname for windows 2003

    One thing to remember is the WCS license is tied to the sever name. So if you change the name if the server, you will have to rehost the WCS license.
    Sent from Cisco Technical Support iPhone App

Maybe you are looking for

  • Changing the Header in a Hybrid Web Container app on BlackBerry

    Hello Experts! I am trying to add a custom header to Hybrid Web Container Apps on SUP 2.0.  It would be nice to add branding or additional text - even the ability to center the text would be nice.  I have tried various jQuery approaches and can see t

  • Bank charges-CM

    Hi, Just want to know the process of & pre requisites of transfering Bank charges from Cash Management to General Ledger in Oracle 11i Thanks Arun

  • How to have fonts display properly in iTunes?

    I have a lot of foreign songs that are named in non-latin alphabet. iTunes displays gibberish.Is there a way for them to display properly?

  • Error when executing SAP_PD with rule for infotype

    HI, I am doing create organizational unit using SAP_PD generic service. I have defined a rule in HRASR_DT transaction to restrict address info type 1028. Infotype should trigger based on the conditions only. when i execute the complete form and click

  • Method to browse/edit  the user/group in SunOne DS  on client side

    I had installed a sunone directory server in a window 2003 server. I want to allow user/client to edit the group/user attribute, how can I do that? Exclude writing a java program to retrieve the information from the sun one directory server, are ther