Cisco wireless mobility 521

Hi
Can somebody help me i am trying to set the wpa security on a wireless 521 access point, but it is just unable to accept the key!!!!!! Any ideas.

The current security standard for wpa security is EAP/802.1x authentication. Following links may help you
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c40b6.shtml
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item0900aecd801e3e59.shtml

Similar Messages

Compare and Contrast :- Mobile Networks(GSM/CDMA) and CISCO Wireless-Mobility

Hi,
I am a CCNA certified Electronics and Communications Engineering Graduate from India.
Nowdays the market here is up in mobile networking driven by companies like Nokia-Siemens Networks, Ericsson, etc.
Wireless Mobile Networks are all geared up for 3G UMTS(Universal Mobile Telecommunications System) architecture.(in GSM).
* My question is how are the above mentioned networks different from the Cisco Wireless Mobility concepts?
* What is common in them?
I know that these mobile networks are converting to packet-switched systems from legacy circuit ones.
* Does cisco come in only as a backbone Routing and Switching hardware providerfor this area,
Or does it offer a complete Unified End-to-End Solution in this domain?
is the difference just size??

Neal,
I do not think that in a forum like this we will be able to provide you a full answer. I recommend that you contact your Cisco account team as they will be able to work through all of the details to your design and fill the requirements of your customer.
A few things for you to look into and ask your account team.
The CDMA2000 1x RTT gateway is the PDSN this gateway is very similar to the GPRS gateway
The MWR 1900 is designed for an IPRAN network design and may or may not fall into what you have describe but your account team can help you with that
The Cisco MAR3200 is a mobile router that is designed to route between various radio access methods such as CDMA or GSM or WLAN etc. It will also do mobile IP.
Cisco has an extensive solution range for both the access gateways and back end services such as service selection authentication accounting and billing.
What you are asking for can be done using Cisco products but, it is a complex network design so please contact your account team for full details.
I am sorry I could not answer your question 100% but hope I have given you enough leads to get the design sorted
David

Wireless Internet Access (Cisco IP NGN or Cisco Wireless Mesh Networkin)??

Dear Cisco Wireless Team
Please educate us on where to start, or the CISCO product we might need to purchase
We are trying to branch out a new Internet wireless access and wireless phone service business in our company, and presently looking for the right Cisco product solution to purchase to enable us offer this service in LAGOS, NIGERIA.
The service will be rendered in Africa, the country NIGERIA, and the city LAGOS.
We would like to mount or install the product in Lagos, Nigeria.
As we are new to this kind of service. We would appreciate if the Cisco wireless team can work with us in pointing or directing on the right product to purchase and what are required. We understand the Cisco Wireless Mesh Networking Solution, Cisco IP Generation Network, Cisco 12416 or 7600 Series Router might be the right products to purchase, but we are not sure on what needed or what are required to meet our service need.
Possibly we would like to offer Wireless Internet Access to unlimited subscribers, and also Wireless or Mobile Phone service to unlimited subscribers in Nigeria.
Anticipating your reply

I suppose Cisco Wireless Mesh Networking would be a good choice.The Cisco mesh architecture makes it easy to scale coverage as capacity needs dictate, including increasing access point density; adding wired connections, controllers, and radios; and using dual high-powered, high-sensitive radios and a selection of high-gain antennas.Refer the document for IP NGN in the following URL http://www.cisco.com/en/US/netsol/ns537/networking_solutions_solution_category.html

Cisco 3850 Mobility Agent unable to connect clients

Hi
We are trying to use Cisco 3850 as Mobility agents with 5760. We can't seem to get the clients to authenticate to the radius server. We don't even see them appear in the radius logs.
We have defined the radius server and the profile
wlan Wireless 2 WAP
aaa-override
accounting-list Radius
client vlan wireless
security dot1x authentication-list Radius
session-timeout 1800
no shutdown
radius server Primary
address ipv4 x.x.x.x auth-port 1812 acct-port 1813
timeout 5
retransmit 2
key 7 ........
radius server Primary
address ipv4 x.x.x.x port 1812 acct-port 1813
timeout 5
retransmit 2
key 7 .........
The client appears to connect to the AP but can't authenticate so gets kicked off
If we do a test aaa group username password then it says that it's sucessful.
In the debug we get 802.1X required but then it never seems to get any further.

Alright, so I finally figured out the issue with this. I had a Mobility Anchor set on the guest WLAN and once I removed that all started working again.
What is Mobility Anchor?
A. Mobility Anchor, also referred to as Guest tunneling or Auto Anchor Mobility, is a feature where all the client traffic that belongs to a WLAN (Specially Guest WLAN) is tunneled to a predefined WLC or set of controllers that are configured as Anchor for that specific WLAN. This feature helps to restrict clients to a specific subnet and have more control over the user traffic. Refer to the Configuring Auto-Anchor Mobility section of Cisco Wireless LAN Controller Configuration Guide, Release 7.0 for more information on this feature.

Interoperability of cisco wireless products?

I've been doing a lot of research on various Cisco wireless products and the options are kind of confusing.
I'll start with my deployment; I have two locations both of which have a manufacturing and warehouse environments (no climate control) and regular offices.
Location 1 needs 3 APs on the production floor and 1 in the offices.
Location 2 needs 5 APs on the warehouse floor and 4 for the offices.
I was thinking about using the Cisco 521 APs for both the production floor and offices and the Cisco 526 Wireless Controller for Location 1. I figure that will give them room for expansion and keep the costs low.
For location 2 I was thinking about the Aironet 1240AG APs for the warehouse floor, Aironet 1140AG APs for the offices and then a Cisco 2112 Wireless Controller to manage all the APs.
Both locations require WPA (or WPA2) encryption and roaming.
My questions are:
Will the 521 APs work with the 2112 controller? For that matter, what sort of interoperability is there with the APs and controllers? Can I manage any Cisco AP with any Cisco Controller?
Are there any cheaper APs than the 1140AG that will work with the 2112 controller?
Is the 1240AG a good choice for a non-climate controlled warehouse environment? The APs are going to be mounted on the ceiling which is roughly 50 feet high and I'm going to be very upset if I deploy these APs and then have one fail during the summer 6 months later because it wasn't made for volatile environments.
The 521 APs are only going to be about 15 feet up so they can be accessed with a ladder so I'm not so worried about them.
Thanks!

Will the 521 APs work with the 2112 controller?
No.
Are there any cheaper APs than the 1140AG that will work with the 2112 controller?
You could try the 1130. 1140 supports 802.11n while 1130 is a/b/g only.
Is the 1240AG a good choice for a non-climate controlled warehouse environment?
The 1240, like the 1130, supports a/b/g only while the 1250 supports a/b/g/n. The newer 1260 is controller-based only. The 1240, 1250 and 1260 use external antennae that's an OPTION.

Cisco wireless and Apple Mac woes

Hello all,
I've been working with Cisco wireless and WLC's for a couple of years now but the recent onslaught of Apple Mac's is giving me heart burn. I've seen this at numerous sites now and need to throw it to eht community for guidance.
Basically we have had a number of instances where the Macs just fall off the wifi. Sometimes it's when they wake from sleep and other times when roaming between AP's (1131s with same SSID's). Our standard install is WPA2 and per ap local authentication. PC's work fine and never an issue.
We have completed a survey with a spectrum analyser and no RF interefence is present nor errors on the radio interface.
Questions:
- Is there a preferred Cisco config/setup for Mac's to work reliably? I've heard loads of rumors but nothing concrete and nor can I find anything specific.
- Should I be setting up WDS in case there is an authenticating issue.
- For those who are Mac gurus and happen to be reading. What Mac options we should look at?
This has all come to a head because the clients IT company who recommended the Macs (different from us doing the network infrastructure) are insisting that the problem is Cisco incompatibility and that we should rip out the Cisco kit and install airports (what tha!!!).
Thanks in advance for any pointers.
For those who like a config here it is .... Vanilla stuff really
Building configuration...
Current configuration : 2236 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP4
no logging console
enable secret xxxxxxxxxxxxxxxxx
no aaa new-model
dot11 syslog
dot11 ssid Home
   vlan 1
   authentication open
   authentication key-management wpa
   guest-mode
   mbssid guest-mode
   wpa-psk ascii xxxxxxxxxxxx
dot11 ssid avnet
   vlan 2
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii xxxxxxxxxxxxxxxx
username abcd password 1234
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers tkip
encryption vlan 2 mode ciphers tkip
ssid Home
mbssid
speed basic-1.0 basic-2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2412
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
hold-queue 80 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface BVI1
ip address 192.168.10.54 255.255.255.0
no ip route-cache
ip default-gateway 192.168.10.1
no ip http server
no ip http secure-server
bridge 1 route ip
line con 0
line vty 0 4
login local
end

Yeah!! even i have come across multiple issue with MAC and Cisco.. these are the below settings which i normally do on the cisco gears and most of the times this solved the issue..
on the IOS AP disable Aironet Extentions and set the poer local and ofdm to max
no dot11 extension aironet
power local cck max
power local ofdm max
end
On the WLC, disable Aironet IE..
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

I have a Cisco wireless router. Can I buy an Airport Express plug in booster for a distant part of my house or do I need an Airport Extreme base station instead to make the Airport Express plug in booster work?

Can I buy an Airport Express plug-in wifi signal booster to connect to a Cisco wireless router, or do I have to buy an Airport Extreme base station to make the Airport Express plug-in work?

You would need either an AirPort Extreme or an AirPort Express connected to the Cisco router, with a permanent Ethernet cable connection.
Configure the Extreme or Express that is connected to the Cisco router to "create a wireless network".
Then, you could add an AirPort Express to "extend a wireless network" to provide more wireless coverage for the network that the Extreme or Express would be creating.
Remember that the Express can only "extend" the quality of signal that it receives, so it must be located where it can receive a strong signal from the "main" AirPort.
If you don't need the Cisco wireless signal, you could turn it off.....or use that network for guests or something similar.
The bottom line here......you always need two Apple routers if you want to extend the network wirelessly.

MacBook Pro will not connect to Cisco Wireless Network

I have just bought a brand new MacBook Pro, running Leopard (OSX 10.5.1) and I just cannot get it to connect to the Wireless Network at my workplace.
The MBP connects to wireless network and authenticates just fine, but will not obtain an IP address from the DHCP server.
The wireless network consists of 16 Cisco Aironet 1200 Access Points controlled by a Cisco Wireless Network Controller. It does not broadcast its SSID and is WEP 128-bit hex protected.
Changing the network from WEP to WPA is out of the question for me as this is under the control of my customers IT Department and they do not have any problems with their PCs connecting to the network. It appears to be an Apple issue.
For reference, my old Vaio PC, my Nokia N95 and my iPod Touch ALL connect to the same wireless network without any problems whatsoever, first time, every time!
If I boot into Windows XP from my Boot Camp partition, XP can connect wirelessly to the network without any problems, so it is not MacBook hardware related...
It has to be a bug in Mac OSX... doesn't it?!?
Things I have already tried (following suggestions on many forums):
* Switching Airport off/on
* Deleting various network-related Plist files and rebooting
* Manually assigning an IP Address (not really permitted but doesn't work anyway!)
* Disabling all network adaptors except Airport
AP Grapher shows that the MBP is connected to the wireless network, at good strength, and packets are being sent and received, but Internet Access is not possible as no IP Address has been assigned. Instead, my MBP shows a 169.* IP Address (self-assigned). It should be a 10.1.255.* address.
Can anybody please help? Thank you.

i posted this same reply elsewhere because it worked for me for my Buffalo wireless router: try manually setting your IP address instead of relying on DHCP, which sometimes (I don't know why) doesn't work well with Macs. It's a good get around. I am a happy Mac user but nothing is perfect on earth, and when the Mac gives problems, it does give a lot of frustration. Macs are not as easy to troubleshoot as Win because a Mac is built to be user friendly(and it works most of the time), meaning a lot of the background computing stuff is hidden away from users to avoid user accidentally upsetting some settings.
Unfortunately, the highly automated troubleshooting wizards provided by OS X are not perfect so when these software wizards fail to resolve the problem, like my Network Diagnostics, I have to spend more time tinkering around. There's "Terminal" of course but then most of us, especially PC converts to Macs, don't know how to use it.
You should also try updating your MBP, see if there are any new updates being released.

Warning page on Cisco Wireless Lan Controller for guest access

Hi,
We have an Cisco wireless LAN controller 4400 in our organization, and lots of guest using our Wi-Fi network.
I would like to configure a warning and terms and condition page when guest using first time our network.
Can you please let me know is that possible without adding external web server and how to configure.
Many Thanks in Advance
Amit Sharma

Hi Amit,
Hope you are doing great!!
the below link will help you in getting the issue resolved!!
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00809bdb5f.shtml
Please dont forget to rate the usefull posts!!
Regards
Surendra

Cisco Wireless AP Report.

I would like to develop a report package for Cisco Wireless device using the SNMP (MIB Objects) access. Can anyone suggest me what are all kind of report i can produce ..?
Like, CPU Usage, Memory and Buffer Usage, Process utilization and Conne cted Nodes. etc.,
Does this device suppor to get all kind of information from MIBs?.
Thanks,
Moorthy,

You can get the Aironet MIBs from: http://www.cisco.com/public/sw-center/sw-wireless.shtml but will have to look at the MIB definitions to find out which ones to use. There's no short cut.

Is it possible to use a Linksys By Cisco Wireless-G Internet Home Monitoring Camera with Labview

I was wondering if it is possible to use a 'Linksys By Cisco Wireless-G Internet Home Monitoring Camera' with Labview
http://www.dabs.com/productview.aspx?Quicklinx=53PX&SearchType=1&SearchTerms=network+cameras&PageMod...
I wan't to be able to get the raw data from the camera and analyse it.
Message Edited by Jam.hall on 03-25-2009 09:03 AM
Solved!
Go to Solution.

Hi Jam.Hall
I am somewhat hesitant to say you will be able to use this camera with LabVIEW. It all depends on what functionality you are wanting to utilise on the camera, and how much video you want to analyze.
- If you want to use the wireless functionality, I am concered that the on board web server will compress and embed the video stream. I do not beleive this is something we can access in LabVIEW.
- If you wish to use the ethernet connection, if it is Gigabit Ethernet, then you should be able to use our IMAQ for GigE driver to bring in the feed, but looking at the specs for the camera, I'm not sure that this is an option.
- My other suggestion might be to utilise the record video stream function that the camera has. Depending on the format of the video file, you may be able to read in the recorded file and analyse it in LabVIEW.
If you could explain the purpose of your application, and what you would like to achieve with the system, there may be more suitable products that you can use.
Kind regards,
Sheela Sujeeun
Applications Engineer
National Instruments UK

Microsoft wireless mobile mouse 4000 issue

My wife has a 4-year old MacBook Pro running 10.6 (can't get her to change...). We recently had to replace her MS Wireless Mobile Mouse 4000--we've both used these for years. We're having an issue with hers...the left button won't go "back" in Safari (or any other program for that matter) and I've tried everything, including assigning the proper keystroke to the button, etc. When I look at her Microsoft Mouse preference panel, it does not show the correct mouse, having an extra button. I've downloaded the latest version of their intellimouse software and it doesn't matter. When I try to get mouse info from the preference panel it tells me it can't see a mouse connected. Anyone got any ideas?
Thanks in advance.
Rocketman

" When I try to get mouse info from the preference panel it tells me it can't see a mouse connected. "
Did you replace the USB receiver as well? The receiver needs to be paired with the new mouse.

Cisco wireless control system

we are using cisco wireless control system i need block some MAC address or devices how can i do it

Hi,
Yes you can block the specific client using MAC Address filtering option in WCS
This option is avialbe in Configure> Security >MAC Filtering
here you can create new template as per your requirement
Go through below link for detail knowledge.
http://www.cisco.com/c/en/us/td/docs/wireless/wcs/7-0/configuration/guide/WCS70cg/7_0temp.html#wp1095263

Cisco Wireless Location Appliance

dear
i have WCS with 500 ap License
i need to have Cisco Wireless Location Appliance what lisens i need for 500 ap
please explain to me that

Hi Ahmed,
This is the upgrade License SKU for upgrading WCS to WCS Location;
WCS-LOC-UPG-K9
Supports deployment of Cisco WCS on a single server only.
For customers upgrading from their existing Cisco WCS base licenses to equivalent Cisco WCS location licenses running Cisco WCS Software Release 4.1 or later.
Available as Cisco WCS location in increments of 50, 100, or 500 lightweight access points.
Customers currently using this license with Cisco WCS Software Release 4.0 are encouraged to upgrade to Cisco WCS Software Release 4.1, but they are not required to do so.
Order the Correct Cisco WCS SKUs
The process to order Cisco WCS SKUs for WCS-STANDARD-K9, WCS-LOC-UPG-K9, WCS-WLSE-UPG-K9 and WCS-ENT-K9 is presented below. To request help with ordering, please contact Cisco Customer Service: http://www.cisco.com/go/customerservice.
1. Login to the Cisco Ordering Tool.
2. Enter the family SKU of WCS-STANDARD-K9 or WCS-LOC-UPG-K9 or WCS-WLSE-UPG-K9 or WCS-ENT-K9 into "Enter Product" in the Ordering Tool and then press "Enter."
3. The family SKU will display in the ordering area. (Figure 6).
4. Select the "Line" for the family SKU
5. Once you have been taken to the configuration screen, select one of these options from the left side (Figure 7):
For WCS-STANDARD-K9 select one of the sub-SKUs based on the following:
Base: WCS Standard AP Base Option
Location: WCS Standard AP Location Option
For WCS-WLSE-UPG-K9 select one of the sub-SKUs based on the following:
Base: WLSE to WCS AP Base Upgrade Option
Location: WLSE to WCS AP Location Upgrade Option
**For WCS-LOC-UPG-K9 select the sub-SKU:
**WCS AP Location Upgrade Option
For WCS-ENT-K9 select the sub-SKU:
WCS Enterprise AP Location Option
For the WCS-STANDARD-K9 or **WCS-LOC-UPG-K9 SKU families, customers are prompted to order the optional CD (WCS-CD-K9), for a nominal charge, during the ordering process. The WCS-CD-K9 contains one software image of Cisco WCS Software Release 4.1 on a CD for Windows and Linux. This CD is shipped by U.S. mail to the purchaser's address. The optional CD is not available for WCS-WLSE-UPG-K9 because this SKU family already ships in CD format.
6. The right side of the screen will display the licenses available (Figure 7). The price for each SKU is displayed in the Ordering Tool.
7. Each license is orderable in a quantity of one (1) for the quantity blocks specified. To add multiple quantities of license blocks, you must go back to the main screen and order additional family SKUs and then select the sub-SKU option and license quantity block required. Repeat this process as needed, until the correct quantity of license blocks for your sub-SKU have been ordered.
From this good doc;
http://www.cisco.com/en/US/products/ps6305/pro ducts_data_sheet0900aecd804b4646.html
Hope this helps!
Rob

Cisco Wireless Control System need wireless Lan Controller ?

Cisco Wireless Control System need wireless Lan Controller , for Rogue detection

Hi Joao,
The WCS is used in conjuntion with the WLC (Wireless Lan Controller) for Rogue Detection. It is not a must for this function but more of an add-on :)
The Cisco WCS is an optional network component that works in conjunction with Cisco Aironet Lightweight Access Points, Cisco wireless LAN controllers and the Cisco Wireless Location Appliance.
From this doc;
http://www.cisco.com/en/US/products/ps6305/index.html
Overview of WCS
The Cisco Wireless Control System (WCS) is a Cisco Unified Wireless Network Solution management tool that adds to the capabilities of the web user interface and command line interface (CLI), moving from individual controllers to a network of controllers. WCS includes the same configuration, performance monitoring, security, fault management, and accounting options used at the controller level and adds a graphical view of multiple controllers and managed access points.
WCS runs on Windows 2003 and Red Hat Enterprise Linux ES 4.0 and AS 4.0 servers. On both Windows and Linux, WCS can run as a normal application or as a service, which runs continuously and resumes running after a reboot.
The WCS user interface enables operators to control all permitted Cisco Unified Wireless Network Solution configuration, monitoring, and control functions through Internet Explorer 6.0 or later. Operator permissions are defined by the administrator using the WCS user interface Administration menu, which enables the administrator to manage user accounts and schedule periodic maintenance tasks.
WCS simplifies controller configuration and monitoring while reducing data entry errors with the Cisco Unified Wireless Network Controller autodiscovery algorithm. WCS uses the industry-standard SNMP protocol to communicate with the controllers.
From this good doc;
http://www.cisco.com/en/US/products/ps6305/products_configuration_guide_chapter09186a00806b7270.html#wp1131195
Detect and Locate Rogue Access Points
From this WCS doc;
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806f070a.shtml#new5
Rogue Detection under Unified Wireless Networks
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_white_paper09186a0080722d8c.shtml
Hope this helps!
Rob

Cisco wireless mobility 521

Similar Messages

Maybe you are looking for