Cisco WLC 5508 Mac Filtering

Hi Group, how are you?.
I know as Mac filtering feature works, but I need the opposite. I need to filter some mac-address to a particular SSID and permit all the other mac-address.
Please, has anyone any ideas?.
Thanks.
Andrés.

Hi Andres,
I think stephan was talking about vlan based access control via RADIUS:
check this document:
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
Regards
Dont forget to rate helpful posts

Similar Messages

  • Cisco WLC 5508 - NPS Radius

    Cisco WLC 5508
    Software Version: 7.4.100.0
    Windows Server 2008R2
    I've got everything setup on the Windows Server 2008 side of things (certificates, radius clients, etc)
    I added the radius server on the WLC, and configured a new WLAN to use it.
    Both are on the same subnet.
    When trying to conect to the WLAN it kept failing.  I installed wireshark on the server to monitor the radius traffic, and to my surprise there was no radius traffic showing up on the server.  The radius statistics on the WLC are at 0 as well, so it's like the WLC isn't even attempting Radius.
    I reverified that the server was enabled on both the security tab and the WLAN itself on the WLC.  Rebooted the controller and the server, all to no avail.  I used a radius test client, and can successfully send radius commands to the server using that utility.
    Frustrated, I just kept trying to reconnect on my wireless device, and after about the 15th try, finally I saw radius activity on wireshark.  It rejected my access, but at least I saw activity.  It also registerd radius statistcs on the WLC as well.
    So now if I keep trying to connect repeatedly, about every dozen or so times the WLC actually will send a radius request to the server.
    What in the world is going on here?

    I do have local management users on the controller.
    Some hours later I added the option of authenticating management users, for the NPS server. Then logged inn to the management GUI using NPS radius, worked just fine.
    However, these commands have been useful to me several times, to make sure unsuccessful requests appear in the Windows Event log:
    auditpol /get /subcategory:"Network Policy Server"
    If it shows ‘No auditing’ or just "Success", you can run this command to enable it:
    auditpol /set /subcategory:"Network Policy Server" /success:enable /failure:enable
    So now I know that the NPS radius server works, for management access. I will go to the customer's site some other day to test it for 802.1x authentication. If not, I'll do some debugging to decide wihich to blame - the WLC or NPS.

  • Cisco WLC 5508 not sending SNMP Traps

    Hello Everyone.
    I'm having a weird error on our WLC environment. We have an HA with two cisco WLC 5508 and i cannot get SNMP Traps working on a Windows PC running Kiwi Syslog server (free ed.).
    I can receive correctly Syslog messages, but not traps.
    I Tried also to send SNMP Traps from WLC to a different PC using Linux with snmptrapd and it works fine.
    I tried then to send from my Linux box a snmp trap to my Windows PC, and it works fine, but i still cannot receive anything from WLC.
    Using Wireshark to detect traffic, i cannot see any packet on udp port 162.
    I cannot figure out any problem with my scenario, but i can see the following errors on syslog:
    *rmgrTrasport: Mar 30 16:08:22.602: #RMGR-3-INVALID_PING_RESPONSE: rmgr_utils.c:270 Ping response from <my_windows_PC> is invalid. Ip address do not match.
    My WLC Version is 7.6.130.0
    Thank you for your support.

    I have gone through your query and found the following fruitful links ,please let me know if it helps and mark it correct answer if it is.
    https://www.manageengine.com/network-monitoring/help/userguide/processing_traps.html
    https://rscciew.wordpress.com/2014/10/12/snmp-configuration-on-wlc/
    Thanks :)

  • Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users

    Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users
    I've been given a fantastic "opportunity" by my boss to use our existing wireless infrastructure to provide internet access to potentially upto 2000 VIP guests arriving with BYOD devices, in a very densely populated area for a 3 day event. We are talking an area of approx 200m x 15m. Think of it as an awards ceremony/concert. The solution will also be mobile so we will be using internet breakout from different telcos as it will move to approx 20 countries. The area is also incredibly densely populated with other wifi APs. I did a brief site survey and AirMagnet could detect over 2500 other 'rogue' APs from where I was stood! I hope CleanAir works!
    We need a simple authentication method for them to connect with zero admin from our side. We don't want to just offer up a rolling daily PSK as that's a bit amateur and we don't really want the VIP guests sharing the PSK with others during their stay. Ideally they could self-provision by providing an email address.
    I know the WLC can handle webauth for local users but I don't think it scales very well. ie I don't think I can offer the account to several hundred people.
    Cisco ISE looks a very expansive (and expensive) product but I don't think we need all it's capabilities (do I?). It would be nice to just ask a potential user for their email address and grant them access and email them next year. I've seen Cisco NAC but that looks over the top too for just guest users who will only be accessing a shared internet connection.
    I've seen 3rd party supposed software solutions from Kiosk Antamedia etc do they work with Cisco Enterprise WLC solutions?
    We'd like to limit users to a certain (low) bandwidth and block (say) torrent traffic to keep the general user experience worthwhile.
    Does anybody have any case study documents or experience of such a project? As well as the authentication it's how well the APs will handle the dense potential number of clients trying to connect in such a confined space. 
    Any suggestions would be gratefully appreciated from the knowledgeable community.
    Cheers,
    Mike

    Hi Rasika,
    We are having WLC 5508 model with software version running 7.4.121.0. AP Models are AIR-CAP2602I.
    Normally our WAN links are good even while the issue pertains. We are connected to remote offices over ipsec site to site vpn for WAN. The link latency in WLC between the AP and the controller shows  <1ms.
    currently the Guest network is using WPA2-PSK auth given in the controller. we are trying to find a option to make the Guest wireless auth local to the office, and see if this solves the problem. 
    any suggestions,
    Thank you,
    Arjun

  • Cisco WLC 5508 in HA mode error

    Hai ,
    I am Getting the below Error in Cisco WLC 5508, Version 7.4.100.0 in HAmode. The WLC contains Access Points having in local and Flex Connect Mode.
    RF failure notification ErrorType: 32 Reason :Error: Config Sync failed on Standby for the usmdb:HA_send_usmDbApfMsDelete,
    I sam a same bug in Cisco WLC 7.4.100.0 release notes similar to the error like
    RF failure notification ErrorType: 32 Reason :Error: Config Sync failed on Standby for the usmdb:HA_send_usmDbSpamSetRadSlotAntennaType.
    Any Ideas?

    HI Mohamed,
    its a open Caveats  in 7.4.100.0
    CSCud26632
    Symptom: The following SNMP trap appears on the controller when you change the channel width number to 40-MHz:
    RF failure notification ErrorType: 32 Reason :Error: Config Sync failed on Standby for the usmdb:HA_send_usmDbSpamSetRadSlotAntennaType.
    Conditions: Controller is in an HA pair. Join the 802.11n access point to the controller and change the channel width to 40-MHz and channel number to 157.
    Workaround: None
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn74.html
    Reagrds
    Please rate helpful posts

  • Need Information of cisco WLC 5508 LAG Interface

    HI
    We have cisco WLC 5508 in our network and right now ,this WLC is connected to two ports of each core switches.Both CORP and GUEST SSID are configured on this WLC.
    Now we want to segregate the trafffic og GUEST to on core switches from WLC. SO my question is ,how can we achieve this without using guest anchor controller ?
    Can i use one interfcae cisco WLC 5508 and connect it to the firewall or any device ?
    Thanks
    Puneet

    Hi
    Thanks ...I am using WLC as a DHCP server for Guest.
    So  i want to know ,is there any requirement that GUEST subnet should be pingable from WLC management IP address.
    my topology is here...
    Corp network and management network are reachable however management metwork is not pinagble from guest netowrk.

  • Cisco wlc 5508 with 30 Vlan

    Hello
    i need your help
    i want to configure Cisco WLC 5508 whith 03 vlans, 3750 as core swich
    - management Vlan
    - local-user vlan
    - Guest Vlan
    i want to know all steps or config to do on WLC 
    thx

    Hi,
    Just check this.
    It may help u.
    Wireless LAN Controller and Lightweight Access Point Basic Configuration Example
    http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/69719-wlc-lwap-config.html
    http://rscciew.wordpress.com/2014/01/22/configure-dynamic-interface-on-wlc/
    Webauth for guest users:
    http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html
    http://rscciew.wordpress.com/2014/06/19/wlc-webauth-configuration/
    Regards

  • Cisco WLC 5508 with Nexus 5048 CDP error

    Hello,
    We got cisco WLC 5508 running 74.121.0
    The WLC is connected to Nexus 5548 with dual-homed.
    We receive CDP duplex mismatch from the Nexus switches.
    Any ideas?

    Can you check the duplex info. of the neighbor using
    router#show cdp neighbors detail

  • Error APF_HA-3-SYNC_RETRANSMIT_FAIL - Controller Cisco WLC 5508

    hello,
    I have two controllers on Cisco WLC 5508 HA version 7.5.
    I'm having several sync error logs:
    *haSSOServiceTask3: Jan 22 09:22:51.637: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (00:0b:6b:b3:d4:6b )data sync. Retry after 300 secs.
    *haSSOServiceTask4: Jan 22 09:22:51.037: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (60:67:20:fa:19:04 )data sync. Retry after 300 secs.
    *haSSOServiceTask2: Jan 22 09:22:50.838: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (04:fe:31:3b:7d:ca )data sync. Retry after 300 secs.
    *haSSOServiceTask2: Jan 22 09:22:50.838: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (88:9b:39:c3:cf:42 )data sync. Retry after 270 secs.
    *haSSOServiceTask3: Jan 22 09:22:50.838: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (18:e2:c2:c0:9b:5b )data sync. Retry after 300 secs.
    *haSSOServiceTask0: Jan 22 09:22:50.837: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (08:70:45:77:36:60 )data sync. Retry after 240 secs.
    *haSSOServiceTask0: Jan 22 09:22:50.837: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (20:64:32:cb:13:a8 )data sync. Retry after 180 secs.
    *haSSOServiceTask0: Jan 22 09:22:50.837: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (8c:70:5a:2e:36:e0 )data sync. Retry after 300 secs.
    *haSSOServiceTask4: Jan 22 09:22:50.837: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (58:94:6b:65:ad:0c )data sync. Retry after 300 secs.
    *haSSOServiceTask1: Jan 22 09:22:50.836: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (40:2b:a1:53:8d:a9 )data sync. Retry after 300 secs.
    *haSSOServiceTask4: Jan 22 09:22:50.836: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (a4:17:31:16:19:2c )data sync. Retry after 300 secs.
    *haSSOServiceTask1: Jan 22 09:22:50.836: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (04:1e:64:7e:19:31 )data sync. Retry after 300 secs.
    *haSSOServiceTask4: Jan 22 09:22:50.639: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (60:67:20:33:7c:74 )data sync. Retry after 300 secs.
    *haSSOServiceTask4: Jan 22 09:22:50.639: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (00:26:c6:57:61:34 )data sync. Retry after 300 secs.
    Has anyone had something similar?

    Hi Valerio, did you ever find out what this error was. I am seeing the same  error but on 7.6
    #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2966 Maximum retransmission exceeded for client (8c:00:6d:16:7b:3d )data sync

  • Cisco ISE 1.2 & Cisco WLC 5508 v7.6

    Hi all,
    we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
    Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
    I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
    Thanks all
    Mario De Rosa

    Hi Neno,
    right I have this almost working now.
    I have simplified the setup. I am not going to do any client provisioning at the moment.
    So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
    Now I am trying to introduce the posture element & per user ACLs.
    I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
    DNS resolution seems to be working fine.
    VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
    VLAN10 is the branch DATA VLAN.
    below is some output to give you some more details...
    (Cisco Controller) >show client detail 00:24:d6:97:b3:be
    Client MAC Address............................... 00:24:d6:97:b3:be
    Client Username ................................. [email protected]
    AP MAC Address................................... 18:33:9d:f0:21:80
    AP Name.......................................... test-flex-ap
    AP radio slot Id................................. 0
    Client State..................................... Associated
    Client NAC OOB State............................. Access
    Wireless LAN Id.................................. 2
    Hotspot (802.11u)................................ Not Supported
    BSSID............................................ 18:33:9d:f0:21:81
    Connected For ................................... 128 secs
    Channel.......................................... 6
    IP Address....................................... 10.130.130.120
    Gateway Address.................................. 10.130.130.1
    Netmask.......................................... 255.255.255.0
    IPv6 Address..................................... fe80::f524:1910:69f0:9482
    Association Id................................... 1
    Authentication Algorithm......................... Open System
    Reason Code...................................... 1
    Status Code...................................... 0
    Client CCX version............................... 4
    Client E2E version............................... 1
    --More-- or (q)uit
    Re-Authentication Timeout........................ 1651
    QoS Level........................................ Silver
    Avg data Rate.................................... 0
    Burst data Rate.................................. 0
    Avg Real time data Rate.......................... 0
    Burst Real Time data Rate........................ 0
    802.1P Priority Tag.............................. disabled
    CTS Security Group Tag........................... Not Applicable
    KTS CAC Capability............................... No
    WMM Support...................................... Enabled
      APSD ACs.......................................  BK  BE  VI  VO
    Power Save....................................... OFF
    Current Rate..................................... m13
    Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
        ............................................. 12.0,18.0,24.0,36.0,48.0,
        ............................................. 54.0
    Mobility State................................... Local
    Mobility Move Count.............................. 0
    Security Policy Completed........................ No
    Policy Manager State............................. POSTURE_REQD
    Policy Manager Rule Created...................... Yes
    AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
    AAA Override ACL Applied Status.................. Yes
    --More-- or (q)uit
    AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
    AAA Override Flex ACL Applied Status............. Yes
    AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
    Audit Session ID................................. c8dc800a00000005b3e7e953
    AAA Role Type.................................... none
    Local Policy Applied............................. none
    IPv4 ACL Name.................................... none
    FlexConnect ACL Applied Status................... Yes
    IPv4 ACL Applied Status.......................... Unavailable
    IPv6 ACL Name.................................... none
    IPv6 ACL Applied Status.......................... Unavailable
    Layer2 ACL Name.................................. none
    Layer2 ACL Applied Status........................ Unavailable
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ none
    No. of mDNS Services Advertised.................. 0
    Policy Type...................................... WPA2
    Authentication Key Management.................... 802.1x
    Encryption Cipher................................ CCMP (AES)
    Protected Management Frame ...................... No
    Management Frame Protection...................... No
    EAP Type......................................... EAP-TLS
    FlexConnect Data Switching....................... Local
    --More-- or (q)uit
    FlexConnect Dhcp Status.......................... Local
    FlexConnect Vlan Based Central Switching......... No
    FlexConnect Authentication....................... Central
    Quarantine VLAN.................................. 0
    Access VLAN...................................... 220
    Client Capabilities:
          CF Pollable................................ Not implemented
          CF Poll Request............................ Not implemented
          Short Preamble............................. Implemented
          PBCC....................................... Not implemented
          Channel Agility............................ Not implemented
          Listen Interval............................ 10
          Fast BSS Transition........................ Not implemented
    Client Wifi Direct Capabilities:
          WFD capable................................ No
          Manged WFD capable......................... No
          Cross Connection Capable................... No
          Support Concurrent Operation............... No
    Fast BSS Transition Details:
    Client Statistics:
          Number of Bytes Received................... 33698
          Number of Bytes Sent....................... 19397
          Total Number of Bytes Sent................. 19397
    --More-- or (q)uit
          Total Number of Bytes Recv................. 33698
          Number of Bytes Sent (last 90s)............ 19397
          Number of Bytes Recv (last 90s)............ 33698
          Number of Packets Received................. 283
          Number of Packets Sent..................... 147
          Number of Interim-Update Sent.............. 0
          Number of EAP Id Request Msg Timeouts...... 0
          Number of EAP Id Request Msg Failures...... 0
          Number of EAP Request Msg Timeouts......... 0
          Number of EAP Request Msg Failures......... 0
          Number of EAP Key Msg Timeouts............. 0
          Number of EAP Key Msg Failures............. 0
          Number of Data Retries..................... 53
          Number of RTS Retries...................... 0
          Number of Duplicate Received Packets....... 2
          Number of Decrypt Failed Packets........... 0
          Number of Mic Failured Packets............. 0
          Number of Mic Missing Packets.............. 0
          Number of RA Packets Dropped............... 0
          Number of Policy Errors.................... 0
          Radio Signal Strength Indicator............ -42 dBm
          Signal to Noise Ratio...................... 41 dB
    Client Rate Limiting Statistics:
    --More-- or (q)uit
          Number of Data Packets Recieved............ 0
          Number of Data Rx Packets Dropped.......... 0
          Number of Data Bytes Recieved.............. 0
          Number of Data Rx Bytes Dropped............ 0
          Number of Realtime Packets Recieved........ 0
          Number of Realtime Rx Packets Dropped...... 0
          Number of Realtime Bytes Recieved.......... 0
          Number of Realtime Rx Bytes Dropped........ 0
          Number of Data Packets Sent................ 0
          Number of Data Tx Packets Dropped.......... 0
          Number of Data Bytes Sent.................. 0
          Number of Data Tx Bytes Dropped............ 0
          Number of Realtime Packets Sent............ 0
          Number of Realtime Tx Packets Dropped...... 0
          Number of Realtime Bytes Sent.............. 0
          Number of Realtime Tx Bytes Dropped........ 0
    Nearby AP Statistics:
          test-flex-ap(slot 0)
            antenna0: 14 secs ago.................... -51 dBm
            antenna1: 14 secs ago.................... -37 dBm
          test-flex-ap(slot 1)
            antenna0: 14 secs ago.................... -51 dBm
            antenna1: 14 secs ago.................... -54 dBm
    --More-- or (q)uit
    DNS Server details:
          DNS server IP ............................. 10.0.17.31
          DNS server IP ............................. 10.0.17.43
    Assisted Roaming Prediction List details:
     Client Dhcp Required:     False
    Allowed (URL)IP Addresses
    (Cisco Controller) >
    (Cisco Controller) >show wlan 2
    WLAN Identifier.................................. 2
    Profile Name..................................... Demo1x
    Network Name (SSID).............................. Demo1x
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Enabled
    Network Admission Control
    Client Profiling Status
        Radius Profiling ............................ Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
        Local Profiling ............................. Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
      Radius-NAC State............................... Enabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    --More-- or (q)uit
    Number of Active Clients......................... 1
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    User Idle Timeout................................ Disabled
    Sleep Client..................................... disable
    Sleep Client Timeout............................. 12 hours
    User Idle Threshold.............................. 0 Bytes
    NAS-identifier................................... mario-test-flex-vwlc
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    WLAN Layer2 ACL.................................. unconfigured
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    Quality of Service............................... Silver
    Per-SSID Rate Limits............................. Upstream      Downstream
    Average Data Rate................................   0             0
    --More-- or (q)uit
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Per-Client Rate Limits........................... Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    --More-- or (q)uit
    Radius Servers
       Authentication................................ 10.0.16.111 1812
       Accounting.................................... 10.131.16.111 1813
          Interim Update............................. Disabled
          Framed IPv6 Acct AVP ...................... Prefix
       Dynamic Interface............................. Disabled
       Dynamic Interface Priority.................... wlan
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       FT Support.................................... Disabled
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Disabled
             AES Cipher.............................. Enabled
                                                                   Auth Key Management
             802.1x.................................. Enabled
             PSK..................................... Disabled
             CCKM.................................... Disabled
    --More-- or (q)uit
             FT-1X(802.11r).......................... Disabled
             FT-PSK(802.11r)......................... Disabled
             PMF-1X(802.11w)......................... Disabled
             PMF-PSK(802.11w)........................ Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-DS mode........................ Enabled
          GTK Randomization.......................... Disabled
          SKC Cache Support.......................... Disabled
          CCKM TSF Tolerance......................... 1000
       WAPI.......................................... Disabled
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       FlexConnect Local Switching................... Enabled
       flexconnect Central Dhcp Flag................. Disabled
       flexconnect nat-pat Flag...................... Disabled
       flexconnect Dns Override Flag................. Disabled
       flexconnect PPPoE pass-through................ Disabled
    --More-- or (q)uit
       flexconnect local-switching IP-source-guar.... Disabled
       FlexConnect Vlan based Central Switching ..... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional
       PMF........................................... Disabled
       PMF Association Comeback Time................. 1
       PMF SA Query RetryTimeout..................... 200
       Tkip MIC Countermeasure Hold-down Timer....... 60
       Eap-params.................................... Disabled
    AVC Visibilty.................................... Disabled
    AVC Profile Name................................. None
    Flow Monitor Name................................ None
    Split Tunnel (Printers).......................... Disabled
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Disabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Assisted Roaming Prediction Optimization......... Disabled
    802.11k Neighbor List............................ Disabled
    802.11k Neighbor List Dual Band.................. Disabled
    Band Select...................................... Disabled
    --More-- or (q)uit
    Load Balancing................................... Disabled
    Multicast Buffer................................. Disabled
     Mobility Anchor List
     WLAN ID     IP Address            Status
    802.11u........................................ Disabled
    MSAP Services.................................. Disabled
    Local Policy
    Priority  Policy Name
    (Cisco Controller) >
    when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
    (Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1) 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE  statusCode is 0 and status is 0 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates  statusCode is 0 and gotSuppRatesElement is 1 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name: 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
    *spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
        MAC: 00:24:d6:97:b3:be, source 4
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410:      [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for  mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header: 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00                                       .._.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410:      [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header: 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00                                       .._.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
    apfMsEntryType = 0 apfMsEapType = 13
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 ACL ID = 255, IPv
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 ACL ID = 255, 
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
    apfMsEntryType = 0 pmkLen = 32
    *DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
      type = Airespace AP Client - ACL passthru
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 A
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile 
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
    *pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
    *IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
    *IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
    *DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    Can you see any obvious reason why the NAC agent wont pop up?
    Thanks
    Mario

  • Cisco WLC 5508 simultaneous Web Auth Users logins?

    Hi there,
    We have 2 WLC5508 (7.2.111.3) with several SSID's.
    One of them is configured as Passthrough with an external splash server. Works fine.
    Now we want to use the "On MAC Filter failure".
    If the client MAC-adresse is configured under MAC Filtering on the WLC, the authentication is done without WebAuth.
    If MAC-adress is not known, the client will be redirect to the external WebAuth server for authentication.
    To keep the Passthrough functionality for the user, we hardcoded an username&password in the splash-page.
    So, every client WebAuth uses the same username&password for authentication against the WLC.
    User Login Policies is set to unlimited.
    So far so good, it seems to work, but I have read, that Cisco 5500 controllers supports only 150 simultaneous Web Auth Users logins.
    The two WLC's have abount 100-170 clients connected.
    Question:
    - Will these be an issue with the 150 simultaneous logins, despited when usin only one user for all Wifi-clients?
    - Can the user WebAuth be done with a Cisco ISE like Passthrough, no username&password should be entered by the user.
      If yes, some guide information wolud be great.
    - When successfully authenticated, a logout screen shows on the Windows client. Can this be hidden some how?
    Thanks for the answers ;-)
    Kind regards,
    Norbert

    Question:
    - Will these be an issue with the 150 simultaneous logins, despited when usin only one user for all Wifi-clients?
    > I believe this means at the same time... I have clients doing the same thing with hundreds or more of guest users
    - Can the user WebAuth be done with a Cisco ISE like Passthrough, no username&password should be entered by the user.
      If yes, some guide information would be great.
    > ISE is really used to login with a username and password and to be able to profile.  You would need to ask that on the Security forum to get their input if this is something then would do or just leave it on the WLC
    - When successfully authenticated, a logout screen shows on the Windows client. Can this be hidden some how?
    > Not really... some machines with popup blocker does block this and you don't see the logout, but you can't remove this.
    Thanks,
    Scott
    *****Help out other by using the rating system and marking answered questions as "Answered"*****

  • Cisco WLC Client MAC address backup to new Controller & ISE

    Hi All,
    We have an existing 4400 controller with MAC filtering for clients configured. Right Now, we are migrating to 5500 WLC and ISE setup.
    We want to use MAC filtering due to company policies on the new Controller as well as ISE.
    Is there a way (from GUI/CLI) that we can export the client MAC Addresses into an Excel file from existing WLC to new WLC & ISE?
    Thanks,
    CJ

    On the CLI issue a show macfilter summary and then import that into excel or a text editor.
    Sent from Cisco Technical Support iPhone App

  • Wlc 2006 mac filtering

    I would like to allow client to access wireless lan based on the client mac-address.
    How I config it on WLC 2006 locally (not using radius server)? If yes, How mnay mac-address can be configured on the wlc2006?
    Thanks.
    Douglas

    Hi Douglas,
    Just wanted to add a note to Ankurs good info;
    Maximum MAC Filter Entries
    The controller database can contain up to 2048 MAC filter entries for local netusers. The default value is 512. To support up to 2048 entries, you must enter this command in the controller CLI:
    config database size MAC_filter_entry
    where MAC_filter_entry is a value from 512 to 2048.
    From this good doc;
    http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a0080813b1c.html#wp42756
    MAC Filtering
    http://www.cisco.com/en/US/products/ps6366/products_user_guide_chapter09186a00805a6ad0.html#wp1040588
    Hope this helps!
    Rob

  • WLC 5760 - MAC Filtering wireless clients

    Hi,
    Does anyone ever deployed mac-filtering authentication to wireless clients in the WLC 5760?
    I've configured a WLAN for Mac-filtering authentication only (named it as "macauth"):
    wlan RNVDOS 4 RNVDOS
    aaa-override
    no broadcast-ssid
    client vlan RNVDOS
    mac-filtering macauth
    no security wpa
    no security wpa akm dot1x
    no security wpa wpa2
    no security wpa wpa2 ciphers aes
    session-timeout 1800
    no shutdown
    Then, below Configuration->Security->MAC Filtering I've added several MAC addresses i.e. :
    MAC Address: 88532e9ef70a  Attribute List: macauth
    Which turned out to be display in the CLI as:
    username 88532e9ef70a mac aaa attribute list macauth
    The problem is that whenever I try to associate the wireless client 88532e9ef70a, the client passes to the exclusion list.:
    Sep 16 10:54:55.603: 8853.2E9E.F70A Adding mobile on LWAPP AP  0C68.03EA.4070 (1)  1 wcm: E9E.F70A (.t^GwtSessionID: 0afe01fbtQ^GwH^Cnz^Gw00dd) was added to ^G$h\225v^K
    Sep 16 10:54:55.603: 8853.2E9E.F70A  Creating WL station entry for client -  rc 0 1 wcm:
    Sep 16 10:54:55.603: 8853.2E9E.F70A Association received from mobile on AP  0C68.03EA.4070  1 wcm: (.t^GwtSessionID: 0afe01fbtQ^GwH^Cnz^Gw00dd) was added to ^G$h\225v^K
    Sep 16 10:54:55.603: 8853.2E9E.F70A qos upstream policy is unknown and downstream policy is unknown 1 wcm: ssionID: 0afe01fbtQ^GwH^Cnz^Gw00dd) was added to ^G$h\225v^K
    Sep 16 10:54:55.603: 8853.2E9E.F70A apChanged 0 wlanChanged 0 mscb ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0 1 wcm: H^Cnz^Gw00dd) was added to ^G$h\225v^K
    Sep 16 10:54:55.603: 8853.2E9E.F70A Applying WLAN policy on MSCB. 1 wcm:  ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:55.603: 8853.2E9E.F70A Applying WLAN ACL policies to client 1 wcm:  0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:55.603: 8853.2E9E.F70A No Interface ACL used for Wireless client in WCM(NGWC) 1 wcm: usOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:55.603: 8853.2E9E.F70A Applying site-specific IPv6 override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm:  ^G$h\225v^K
    Sep 16 10:54:55.603: 8853.2E9E.F70A Applying local bridging Interface Policy for station  8853.2E9E.F70A  - vlan 4, interface 'RNVDOS' 1 wcm: ce 'RNVDOS'
    Sep 16 10:54:55.603: 8853.2E9E.F70A Applying site-specific override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: DOS'
    Sep 16 10:54:55.603: 8853.2E9E.F70A STA - rates (8): 1 wcm:  140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    Sep 16 10:54:55.603: 8853.2E9E.F70A new capwap_wtp_iif_id a45d40000000a5, sm capwap_wtp_iif_id 0 1 wcm: - vapId 4, site 'renova', interface 'RNVDOS'
    Sep 16 10:54:55.603: 8853.2E9E.F70A apfProcessAssocReq (apf_80211.c: 1 wcm: 5137) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from Idle to AAA Pending
    Sep 16 10:54:55.603: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:55.604: 8853.2E9E.F70A
    client incoming attribute size are 0 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:55.604: 8853.2E9E.F70A Sending Assoc Response to station on BSSID  0C68.03EA.4070  (status 256) ApVapId 2 Slot 1 1 wcm: 68.03EA.4070  from Idle to AAA Pending
    Sep 16 10:54:55.604: 8853.2E9E.F70A apfProcessRadiusAssocResp (apf_80211.c: 1 wcm: 2149) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from AAA Pending to Authenticated
    Sep 16 10:54:55.604: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 18) in 10 seconds
    Sep 16 10:54:55.813: 8853.2E9E.F70A Association received from mobile on AP  0C68.03EA.4070  1 wcm: n.t^Gwseconds
    Sep 16 10:54:55.813: 8853.2E9E.F70A qos upstream policy is unknown and downstream policy is unknown 1 wcm: onds
    Sep 16 10:54:55.813: 8853.2E9E.F70A apChanged 0 wlanChanged 0 mscb ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0 1 wcm: H^Cnz^Gw  0C68.03EA.4070  f^G$h\225v^K
    Sep 16 10:54:55.813: 8853.2E9E.F70A Applying WLAN policy on MSCB. 1 wcm:  ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:55.813: 8853.2E9E.F70A Applying WLAN ACL policies to client 1 wcm:  0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:55.813: 8853.2E9E.F70A No Interface ACL used for Wireless client in WCM(NGWC) 1 wcm: usOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:55.813: 8853.2E9E.F70A Applying site-specific IPv6 override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: f^G$h\225v^K
    Sep 16 10:54:55.813: 8853.2E9E.F70A Applying local bridging Interface Policy for station  8853.2E9E.F70A  - vlan 4, interface 'RNVDOS' 1 wcm: ce 'RNVDOS'
    Sep 16 10:54:55.813: 8853.2E9E.F70A Applying site-specific override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: DOS'
    Sep 16 10:54:55.813: 8853.2E9E.F70A STA - rates (8): 1 wcm:  140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    Sep 16 10:54:55.813: 8853.2E9E.F70A new capwap_wtp_iif_id a45d40000000a5, sm capwap_wtp_iif_id 0 1 wcm: - vapId 4, site 'renova', interface 'RNVDOS'
    Sep 16 10:54:55.813: 8853.2E9E.F70A apfProcessAssocReq (apf_80211.c: 1 wcm: 5137) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from Authenticated to AAA Pending
    Sep 16 10:54:55.813: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:55.814: 8853.2E9E.F70A
    client incoming attribute size are 0 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:55.814: 8853.2E9E.F70A Sending Assoc Response to station on BSSID  0C68.03EA.4070  (status 256) ApVapId 2 Slot 1 1 wcm: 68.03EA.4070  from Authenticated to AAA Pending
    Sep 16 10:54:55.814: 8853.2E9E.F70A apfProcessRadiusAssocResp (apf_80211.c: 1 wcm: 2149) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from AAA Pending to Authenticated
    Sep 16 10:54:55.814: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 18) in 10 seconds
    Sep 16 10:54:56.520: 8853.2E9E.F70A Association received from mobile on AP  0C68.03EA.4070  1 wcm: n.t^Gwseconds
    Sep 16 10:54:56.520: 8853.2E9E.F70A qos upstream policy is unknown and downstream policy is unknown 1 wcm: onds
    Sep 16 10:54:56.520: 8853.2E9E.F70A apChanged 0 wlanChanged 0 mscb ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0 1 wcm: H^Cnz^Gw  0C68.03EA.4070  f^G$h\225v^K
    Sep 16 10:54:56.520: 8853.2E9E.F70A Applying WLAN policy on MSCB. 1 wcm:  ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:56.520: 8853.2E9E.F70A Applying WLAN ACL policies to client 1 wcm:  0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:56.520: 8853.2E9E.F70A No Interface ACL used for Wireless client in WCM(NGWC) 1 wcm: usOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:56.520: 8853.2E9E.F70A Applying site-specific IPv6 override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: f^G$h\225v^K
    Sep 16 10:54:56.520: 8853.2E9E.F70A Applying local bridging Interface Policy for station  8853.2E9E.F70A  - vlan 4, interface 'RNVDOS' 1 wcm: ce 'RNVDOS'
    Sep 16 10:54:56.520: 8853.2E9E.F70A Applying site-specific override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: DOS'
    Sep 16 10:54:56.520: 8853.2E9E.F70A STA - rates (8): 1 wcm:  140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    Sep 16 10:54:56.520: 8853.2E9E.F70A new capwap_wtp_iif_id a45d40000000a5, sm capwap_wtp_iif_id 0 1 wcm: - vapId 4, site 'renova', interface 'RNVDOS'
    Sep 16 10:54:56.520: 8853.2E9E.F70A apfProcessAssocReq (apf_80211.c: 1 wcm: 5137) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from Authenticated to AAA Pending
    Sep 16 10:54:56.520: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:56.521: 8853.2E9E.F70A
    client incoming attribute size are 0 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:56.521: 8853.2E9E.F70A Sending Assoc Response to station on BSSID  0C68.03EA.4070  (status 256) ApVapId 2 Slot 1 1 wcm: 68.03EA.4070  from Authenticated to AAA Pending
    Sep 16 10:54:56.521: 8853.2E9E.F70A apfProcessRadiusAssocResp (apf_80211.c: 1 wcm: 2149) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from AAA Pending to Authenticated
    Sep 16 10:54:56.521: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 18) in 10 seconds
    Sep 16 10:54:56.729: 8853.2E9E.F70A Association received from mobile on AP  0C68.03EA.4070  1 wcm: n 10 seconds
    Sep 16 10:54:56.729: 8853.2E9E.F70A qos upstream policy is unknown and downstream policy is unknown 1 wcm: onds
    Sep 16 10:54:56.729: 8853.2E9E.F70A apChanged 0 wlanChanged 0 mscb ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0 1 wcm: A  on AP  0C68.03EA.4070  from AAA Pending to Authenticated
    Sep 16 10:54:56.729: 8853.2E9E.F70A Applying WLAN policy on MSCB. 1 wcm:  ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:56.729: 8853.2E9E.F70A Applying WLAN ACL policies to client 1 wcm:  0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:56.729: 8853.2E9E.F70A No Interface ACL used for Wireless client in WCM(NGWC) 1 wcm: usOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:56.729: 8853.2E9E.F70A Applying site-specific IPv6 override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: from AAA Pending to Authenticated
    Sep 16 10:54:56.729: 8853.2E9E.F70A Applying local bridging Interface Policy for station  8853.2E9E.F70A  - vlan 4, interface 'RNVDOS' 1 wcm: ce 'RNVDOS'
    Sep 16 10:54:56.729: 8853.2E9E.F70A Applying site-specific override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: DOS'
    Sep 16 10:54:56.729: 8853.2E9E.F70A STA - rates (8): 1 wcm:  140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    Sep 16 10:54:56.729: 8853.2E9E.F70A new capwap_wtp_iif_id a45d40000000a5, sm capwap_wtp_iif_id 0 1 wcm: - vapId 4, site 'renova', interface 'RNVDOS'
    Sep 16 10:54:56.729: 8853.2E9E.F70A apfProcessAssocReq (apf_80211.c: 1 wcm: 5137) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from Authenticated to AAA Pending
    Sep 16 10:54:56.729: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:56.730: 8853.2E9E.F70A
    client incoming attribute size are 0 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:56.730: 8853.2E9E.F70A Sending Assoc Response to station on BSSID  0C68.03EA.4070  (status 256) ApVapId 2 Slot 1 1 wcm: 68.03EA.4070  from Authenticated to AAA Pending
    Sep 16 10:54:56.730: 8853.2E9E.F70A apfProcessRadiusAssocResp (apf_80211.c: 1 wcm: 2149) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from AAA Pending to Authenticated
    Sep 16 10:54:56.730: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 18) in 10 seconds
    Sep 16 10:54:56.937: 8853.2E9E.F70A Association received from mobile on AP  0C68.03EA.4070  1 wcm: n.t^Gwseconds
    Sep 16 10:54:56.937: 8853.2E9E.F70A qos upstream policy is unknown and downstream policy is unknown 1 wcm: onds
    Sep 16 10:54:56.937: 8853.2E9E.F70A apChanged 0 wlanChanged 0 mscb ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0 1 wcm: H^Cnz^Gw  0C68.03EA.4070  f^G$h\225v^K
    Sep 16 10:54:56.937: 8853.2E9E.F70A Applying WLAN policy on MSCB. 1 wcm:  ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:56.937: 8853.2E9E.F70A Applying WLAN ACL policies to client 1 wcm:  0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:56.937: 8853.2E9E.F70A No Interface ACL used for Wireless client in WCM(NGWC) 1 wcm: usOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:56.937: 8853.2E9E.F70A Applying site-specific IPv6 override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: f^G$h\225v^K
    Sep 16 10:54:56.937: 8853.2E9E.F70A Applying local bridging Interface Policy for station  8853.2E9E.F70A  - vlan 4, interface 'RNVDOS' 1 wcm: ce 'RNVDOS'
    Sep 16 10:54:56.937: 8853.2E9E.F70A Applying site-specific override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: DOS'
    Sep 16 10:54:56.937: 8853.2E9E.F70A STA - rates (8): 1 wcm:  140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    Sep 16 10:54:56.937: 8853.2E9E.F70A new capwap_wtp_iif_id a45d40000000a5, sm capwap_wtp_iif_id 0 1 wcm: - vapId 4, site 'renova', interface 'RNVDOS'
    Sep 16 10:54:56.937: 8853.2E9E.F70A apfProcessAssocReq (apf_80211.c: 1 wcm: 5137) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from Authenticated to AAA Pending
    Sep 16 10:54:56.937: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:56.937: 8853.2E9E.F70A
    client incoming attribute size are 0 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:56.937: 8853.2E9E.F70A Sending Assoc Response to station on BSSID  0C68.03EA.4070  (status 256) ApVapId 2 Slot 1 1 wcm: 68.03EA.4070  from Authenticated to AAA Pending
    Sep 16 10:54:56.937: 8853.2E9E.F70A apfProcessRadiusAssocResp (apf_80211.c: 1 wcm: 2149) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from AAA Pending to Authenticated
    Sep 16 10:54:56.937: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 18) in 10 seconds
    Sep 16 10:54:57.143: 8853.2E9E.F70A Association received from mobile on AP  0C68.03EA.4070  1 wcm: n.t^Gwseconds
    Sep 16 10:54:57.143: 8853.2E9E.F70A qos upstream policy is unknown and downstream policy is unknown 1 wcm: onds
    Sep 16 10:54:57.143: 8853.2E9E.F70A apChanged 1 wlanChanged 0 mscb ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0 1 wcm: H^Cnz^Gw  0C68.03EA.4070  f^G$h\225v^K
    Sep 16 10:54:57.143: 8853.2E9E.F70A Applying WLAN policy on MSCB. 1 wcm:  ipAddr 0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:57.143: 8853.2E9E.F70A Applying WLAN ACL policies to client 1 wcm:  0.0.0.0, apf RadiusOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:57.143: 8853.2E9E.F70A No Interface ACL used for Wireless client in WCM(NGWC) 1 wcm: usOverride 0x0, numIPv6Addr=0
    Sep 16 10:54:57.143: 8853.2E9E.F70A Applying site-specific IPv6 override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: f^G$h\225v^K
    Sep 16 10:54:57.143: 8853.2E9E.F70A Applying local bridging Interface Policy for station  8853.2E9E.F70A  - vlan 4, interface 'RNVDOS' 1 wcm: ce 'RNVDOS'
    Sep 16 10:54:57.143: 8853.2E9E.F70A Applying site-specific override for station  8853.2E9E.F70A  - vapId 4, site 'renova', interface 'RNVDOS' 1 wcm: DOS'
    Sep 16 10:54:57.143: 8853.2E9E.F70A STA - rates (8): 1 wcm:  130 132 139 150 12 18 24 36 0 0 0 0 0 0 0 0
    Sep 16 10:54:57.143: 8853.2E9E.F70A STA - rates (12): 1 wcm:  130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
    Sep 16 10:54:57.144:  8853.2E9E.F70A  0.0.0.0 START (0) Deleted mobile LWAPP rule on AP [ 0C68.03EA.4070 ] 1 wcm:  site 'renova', interface 'RNVDOS'
    Sep 16 10:54:57.144: 8853.2E9E.F70A Updated location for station old AP  0C68.03EA.4070 -1, new AP  0C68.03EA.4070 -0 1 wcm: va', interface 'RNVDOS'
    Sep 16 10:54:57.144: 8853.2E9E.F70A new capwap_wtp_iif_id a45d40000000a5, sm capwap_wtp_iif_id 0 1 wcm: P  0C68.03EA.4070 -0
    Sep 16 10:54:57.144: 8853.2E9E.F70A apfProcessAssocReq (apf_80211.c: 1 wcm: 5137) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from Authenticated to AAA Pending
    Sep 16 10:54:57.144: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:57.144: 8853.2E9E.F70A
    client incoming attribute size are 0 1 wcm:   (callerId: 20) in 10 seconds
    Sep 16 10:54:57.145: 8853.2E9E.F70A Sending Assoc Response to station on BSSID  0C68.03EA.4070  (status 256) ApVapId 2 Slot 0 1 wcm: 68.03EA.4070  from Authenticated to AAA Pending
    Sep 16 10:54:57.145: 8853.2E9E.F70A apfBlacklistMobileStationEntry2 (apf_ms.c: 1 wcm: 6129) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from AAA Pending to Exclusion-list (1)
    Sep 16 10:54:57.145: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 44) in 10 seconds
    Sep 16 10:54:57.145: 8853.2E9E.F70A client is added to the exclusion list, reason 1 1 wcm: d: 44) in 10 seconds
    Sep 16 10:54:57.145: *apfReceiveTask: 1 wcm:  %APF-4-ADD_TO_BLACKLIST_REASON: Client 8853.2E9E.F70A (AuditSessionID: 0afe01fb5236e37f000000de) was added to exclusion list. Reason: 802.11 association failure 
    Sep 16 10:54:57.836: 8853.2E9E.F70A Ignoring assoc request due to mobile in exclusion list or marked for deletion  1 wcm: fbtQ^GwH^Cnz^Gw00de) was added to ^G$h\225v^K
    Sep 16 10:54:58.533: 8853.2E9E.F70A Ignoring assoc request due to mobile in exclusion list or marked for deletion  1 wcm: fbtQ^GwH^Cnz^Gw00de) was added to ^G$h\225v^K
    Sep 16 10:54:59.231: 8853.2E9E.F70A Ignoring assoc request due to mobile in exclusion list or marked for deletion  1 wcm: fbtQ^GwH^Cnz^Gw00de) was added to ^G$h\225v^K
    Sep 16 10:54:59.922: 8853.2E9E.F70A Ignoring assoc request due to mobile in exclusion list or marked for deletion  1 wcm: fbtQ^GwH^Cnz^Gw00de) was added to ^G$h\225v^K
    Sep 16 10:55:06.972: 8853.2E9E.F70A apfMsExpireCallback (apf_ms.c: 1 wcm: 664) Expiring Mobile!
    Sep 16 10:55:06.972: 8853.2E9E.F70A Scheduling deletion of Mobile Station: 1 wcm:   (callerId: 46) in 60 seconds
    Sep 16 10:55:06.972: 8853.2E9E.F70A apfMsExpireMobileStation (apf_ms.c: 1 wcm: 7067) Changing state for mobile  8853.2E9E.F70A  on AP  0C68.03EA.4070  from Exclusion-list (1) to Exclusion-list (2)
    Sep 16 10:55:06.972:  8853.2E9E.F70A  0.0.0.0 START (0) Deleted mobile LWAPP rule on AP [ 0C68.03EA.4070 ] 1 wcm: 3.2E9E.F70A  on AP  0C68.03EA.4070  from Exclusion-list (1) to Exclusion-list (2)
    Sep 16 10:55:06.972:  8853.2E9E.F70A  0.0.0.0 START (0) FastSSID for the client [ 0C68.03EA.4070 ] NOTENABLED 1 wcm: E9E.F70A  on AP  0C68.03EA.4070  from Exclusion-list (1) to Exclusion-list (2)
    Sep 16 10:55:06.972: 8853.2E9E.F70A Incrementing the Reassociation Count 1 for client (of interface RNVDOS) 1 wcm: D
    Sep 16 10:55:06.972: 8853.2E9E.F70A Clearing Dhcp state for station  ---  1 wcm:  for client (of interface RNVDOS)
    WLC1#
    WLC1#
    Kind Regards,
    Vasco

    Hi Patrick,
    Thank you for sharing your solution. It didn't solved entirely the problem but you pointed to the right direction!
    They are caused, because the system searches for an aaa authorization list, which is not configured.
    To resolve this configure the following
    aaa authorization network mac-filter local
    where mac-filter is the name you defined in the SSID.
    I've used your sugestion to create an aaa local authorization list but instead of naming it with the SSID, I've used the name of the attribute list ( macauth ) and it solved the problem:
    aaa authorization network macauth local
    username 88532e9ef70a mac aaa attribute list macauth
    wlan RNVDOS 4 RNVDOS
    client vlan RNVDOS
    mac-filtering macauth
    WLC1#sh wireless client summ
    Number of Local Clients : 1
    MAC Address    AP Name                          WLAN State              Protocol
    8853.2e9e.f70a APf872.ead7.31da                 4    UP                 11n(5)  
    Cheers,
    Vasco

  • Cisco WLC 5508 V 7.0.116.0 Help

    I have a WLC 5508, that has been working with AIR LAP 1522 AG-E-K9 and AIR LAP 1142N E K9 access points. I have deployed two
    AIR-CAP1552E-A-K9 AP's on the WLC. I had to upgrade to Version 7.0.116.0, and had to set the country code to US ( Was ZA). The good news is that on US country code the new 1552's works great.
    My problem now is to get the existing 1522 and 1142 AP's to work in conjunction with the 1552's on US country code.
    Any information would be greatly appreciated.
    Thank You in advance.

    George:
    Multiple country codes are not supported for MESH APs.
    You can only choose one country if you are using MESH APs whatever the model is.
    If you have MESH APs with multiple country regulatories I think the only way to go is to replace your APs so all of them to be under same regulatory.
    Features Not Supported on Mesh NetworksThese controller features are not supported on mesh networks:
    Multi-country support
    Load-based CAC (Mesh networks support only bandwidth-based, or static, CAC.)
    High availability (fast heartbeat and primary discovery join timer)
    EAP-FASTv1 and 802.1X authentication
    EAP-FASTv1 and 802.1X authentication
    Locally significant certificate
    Location-based services
    Reference: http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008072ea79.shtml
    HTH
    Amjad

Maybe you are looking for

  • Check and validate the characteristic row in query

    Hi Gurus, I am really new to BW, may be a silly question. I Have requirement where I have query, which had characteristic  status having value for open closed items as O and C. Now i need the query to look if status is O,then it should move amount fe

  • Which set of LayoutManagers?

    I have a JPanel (ListPanel) in a JScrollPane. The ListPanel can contain any number of JPanels (NodePanel). Each NodePanel contains a JTextPane as well as other JComponents (JLabel, etc). I want each NodePanel to be displayed with word wrap for the JT

  • Why do we register products with Apple?

    I've just registered my new iPhone 3G with Apple and like all registrations, it's a satisfying feeling when I get the email that confirms the registration. But what I want to know is, why do we even register with Apple? There seems to be no benefit f

  • I cannot get my password accepted to enter my nnotebook HP G62

    I have had the same password since purchase.but now I cannot get my HP G62  to accepr it. Have tried to correct on F10 but no good.

  • Where does a site get saved?

    Hi. When we save a site on iWeb where does it exactly save them? this is one feature I wished iWeb would include in its Preferences settings so that we could at least find it easily or choose where we would prefer to save the site. Thanks for your co