Cisco wlc 5508 with 30 Vlan

Hello
i need your help
i want to configure Cisco WLC 5508 whith 03 vlans, 3750 as core swich
- management Vlan
- local-user vlan
- Guest Vlan
i want to know all steps or config to do on WLC 
thx

Hi,
Just check this.
It may help u.
Wireless LAN Controller and Lightweight Access Point Basic Configuration Example
http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/69719-wlc-lwap-config.html
http://rscciew.wordpress.com/2014/01/22/configure-dynamic-interface-on-wlc/
Webauth for guest users:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html
http://rscciew.wordpress.com/2014/06/19/wlc-webauth-configuration/
Regards

Similar Messages

  • Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users

    Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users
    I've been given a fantastic "opportunity" by my boss to use our existing wireless infrastructure to provide internet access to potentially upto 2000 VIP guests arriving with BYOD devices, in a very densely populated area for a 3 day event. We are talking an area of approx 200m x 15m. Think of it as an awards ceremony/concert. The solution will also be mobile so we will be using internet breakout from different telcos as it will move to approx 20 countries. The area is also incredibly densely populated with other wifi APs. I did a brief site survey and AirMagnet could detect over 2500 other 'rogue' APs from where I was stood! I hope CleanAir works!
    We need a simple authentication method for them to connect with zero admin from our side. We don't want to just offer up a rolling daily PSK as that's a bit amateur and we don't really want the VIP guests sharing the PSK with others during their stay. Ideally they could self-provision by providing an email address.
    I know the WLC can handle webauth for local users but I don't think it scales very well. ie I don't think I can offer the account to several hundred people.
    Cisco ISE looks a very expansive (and expensive) product but I don't think we need all it's capabilities (do I?). It would be nice to just ask a potential user for their email address and grant them access and email them next year. I've seen Cisco NAC but that looks over the top too for just guest users who will only be accessing a shared internet connection.
    I've seen 3rd party supposed software solutions from Kiosk Antamedia etc do they work with Cisco Enterprise WLC solutions?
    We'd like to limit users to a certain (low) bandwidth and block (say) torrent traffic to keep the general user experience worthwhile.
    Does anybody have any case study documents or experience of such a project? As well as the authentication it's how well the APs will handle the dense potential number of clients trying to connect in such a confined space. 
    Any suggestions would be gratefully appreciated from the knowledgeable community.
    Cheers,
    Mike

    Hi Rasika,
    We are having WLC 5508 model with software version running 7.4.121.0. AP Models are AIR-CAP2602I.
    Normally our WAN links are good even while the issue pertains. We are connected to remote offices over ipsec site to site vpn for WAN. The link latency in WLC between the AP and the controller shows  <1ms.
    currently the Guest network is using WPA2-PSK auth given in the controller. we are trying to find a option to make the Guest wireless auth local to the office, and see if this solves the problem. 
    any suggestions,
    Thank you,
    Arjun

  • Cisco WLC 5508 with Nexus 5048 CDP error

    Hello,
    We got cisco WLC 5508 running 74.121.0
    The WLC is connected to Nexus 5548 with dual-homed.
    We receive CDP duplex mismatch from the Nexus switches.
    Any ideas?

    Can you check the duplex info. of the neighbor using
    router#show cdp neighbors detail

  • Trying to get home shaing working on apple tv using Cisco Access points and a Cisco WLC 5508 with 7.2.110 code.  I can get devices working individually but they never see each other.  I can ping the apple tv from my laptop and ipad.

    Trying to get home sharing working on a corporate wireless network.  Cisco wireless.
    WLC5508 controller
    Cisco 3502 access points
    All apple devices on same WLAN - security WPA2-PSK
    ITunes account up to date
    All devices laterst software.
    Can ping apll tv from laptop
    can ping apple tv from ipad
    Can ping ipad from laptop
    can ping laptop from ipad.
    Apple tv never sees any other device.
    Any ideas?

    Fascinating just reading about your setup. I have a WRT350N and have noticed that it will drop its speed, sometimes down to 1Mbps. It seems to do so at about the same time every day, but usually comes back to speed in about 5 minutes. In my experience, the Apple TV will disconnect if the speed falls this low. Try monitoring the Linksys with Netstumbler, Vistumbler, or just in the Windows Network utility.
    Check the "lease obtained" and "lease expired" times for your router to see if that is when the network fails. I've just finished reading an angry thread over at the Linksys forum about the WRT330N where someone mentioned that the router wasn't renewing its lease.
    "I cannot set it run off automatic DHCP from the WRT330N, the router will not assign it an IP every time the lease expires, causing me to have to manually set an IP on the Print server. That's annoying. Having the router drop IP's to individual machines after 12-48 hours...very annoying."
    http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread .id=67412
    If that is the problem, then I would consider setting up a Static IP address for your Apple TV. You can do that through the user interface -> Settings -> Network -> Configure ... (Quite intuitive as you only have change IP address and the subsequent details remain the same.)
    My router assigns IP Addresses in the ranges of 192.168.1.100 ->149. The idea here is to choose an address outside of that range but is not greater than 192.168.1.253 (and should not end in the number 1). You shouldn't have to change the linksys router as long as 50 clients are assigned in that range. You'll have to figure that out by accessing your router webpage at browser address 192.168.1.1 -> the default password is "admin" (without the quotes).
    Good luck.

  • Deployment of WLC-5508 with 2702i-D have performance issue.

    Hi Team,
    We have centrally deployed WLC-5508 with 50 AP licence along with HA scenario. we have 3 locations.
    1- HQ. have 26 AP with POWINJ5.
    2- Branch location A- 8 AP with POWINJ5.
    3. Branch location B have 8 AP with POWINJ4.
    my exception is to achieve that  single SSID with dynamic VLAN from group police (NPS). MY HO have 26 AP and those are working in local mode.
    and branches are connected through flexconnect mode. and all are working with different-2 NPS. 
    Now i am facing a problem with this deployment are following.
    1- branch A have performance issue.
    2- HQ have performance issue.
    3- i don't want to go with dedicated NPS for every location. 
    In order to achieve this deployment i want only single SSID with primary and secondary NPS at my HQ with dynamic VLAN for respective departmental users vlans..
    above is my problem and concern. otherwise i am successfully achieving this solution with dedicated NPS with single group policy. but when i am going forward to achieve my expectation that time i am facing authentication issue at my HQ and sometimes am not able to get proper VLAN IPs. at my HQ. 
    kindly help me in that to understand where I am doing wrong things to achieve my expectation. 
    Thanks.
    Nalin    

    I am facing 2 different problems.
    1st issue- in existing setup we have throughput issue. (while downloading or uploading any data from the internet or Intranet,  that time wireless clients are facing slowness of the Speed. and same time when i am trying from LAN i am not facing any issue)
    2nd Issue- I want to achieve only single SSID with primary and secondary NPS (AD group is bind with vlan Attributes) with dynamic VLAN for respective departmental users.
    for Issue no 2 i have created SSID to achieve the single ssid parameter for every location. in order to achieve i have change all access points mode local to Flexconnect mode after that i have created AP groups location wise and then create flexconnect Groups where i have mapped all the vlan through AAA VLAN-ACL mapping. created interface group and mapped all the vlans in that group. 
    for more understanding please go through the below mentioned CLI view.
    Cisco Controller) >show wlan apgroups
    Total Number of AP Groups........................ 4
    Site Name........................................ GURGAON-AP-GROUP
    Site Description................................. GURGAON-AP-GROUP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Pol                                                                                        icy
     3               gurgaon-interface    Disabled                          None
    --More-- or (q)uit
     4               gurgaon-guest        Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    GUR-AP-01            2     AIR-CAP2702I-D-K9    f4:4e:05:78:ae:e4  default location  1     IN       1
    GUR-AP-05            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b5:18  default location  1     IN       1
    GUR-AP-03            2     AIR-CAP2702I-D-K9    bc:16:65:13:71:00  default location  1     IN       1
    GUR-AP-07            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b3:f8  default location  1     IN       1
    GUR-AP-06            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b3:e0  default location  1     IN       1
    GUR-AP-08            2     AIR-CAP2702I-D-K9    f4:4e:05:45:78:98  default location  1     IN       1
    GUR-AP-02            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b3:2c  default location  1     IN       1
    GUR-AP-04            2     AIR-CAP2702I-D-K9    f4:4e:05:78:ae:64  default location  1     IN       1
    GUR-AP-09            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b4:44  default location  1     IN       1
    Site Name........................................ MUMBAI-AP-GROUP
    Site Description................................. MUMBAI-AP-GROUP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    --More-- or (q)uit
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     1               group for mumbai     Disabled                          None
     2               guest wifi           Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    FAL-7-AP08           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:24:d8         7th Floor  1     IN       3
    --More-- or (q)uit
    FAL-7-AP10           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:18         7th Floor  1     IN       1
    FAL-7-AP14           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:ad:e8         7th Floor  1     IN       1
    FAL-7-AP01           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:b0:4c         7th Floor  1     IN       1
    FAL-7-AP07           2     AIR-CAP2702I-D-K9    f0:7f:06:30:92:bc         7th Floor  1     IN       1
    FAL-7-AP13           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:80         7th Floor  1     IN       1
    FAL-7-AP02           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:94         7th Floor  1     IN       1
    FAL-7-AP05           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:e8         7th Floor  1     IN       1
    FAL-7-AP12           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:f0         7th Floor  1     IN       3
    FAL-7-AP03           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:e4         7th Floor  1     IN       1
    FAL-7-AP06           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:84         7th Floor  1     IN       3
    FAL-7-AP04           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:b0:14         7th Floor  1     IN       1
    FAL-7-AP09           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:c8         7th Floor  1     IN       3
    FAL-7-AP11           2     AIR-CAP2702I-D-K9    f0:7f:06:30:93:08         7th Floor  1     IN       1
    Site Name........................................ MUMBAI-THIRD-FLOOR-AP
    Site Description................................. MUMBAI-THIRD-FLOOR-AP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    --More-- or (q)uit
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     1               group for mumbai     Disabled                          None
     2               guest wifi           Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    FAL-3-AP07           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:a4         3rd Floor  1     IN       3
    FAL-3-AP09           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:94         3rd Floor  1     IN       3
    FAL-3-AP11           2     AIR-CAP2702I-D-K9    f4:0f:1b:73:00:74  3rd Floor- Eurek  1     IN       3
    FAL-3-AP06           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:ae:d0         3rd Floor  1     IN       3
    --More-- or (q)uit
    FAL-3-AP10           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b5:88         3rd Floor  1     IN       3
    FAL-3-AP08           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:9c         3rd Floor  1     IN       3
    FAL-3-AP03           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:af:a0         3rd Floor  1     IN       1
    FAL-3-AP12           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b3:fc  3rd Floor- Eurek  1     IN       3
    FAL-3-AP02           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:28         3rd Floor  1     IN       3
    FAL-3-AP01           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:f4         3rd Floor  1     IN       3
    FAL-3-AP04           2     AIR-CAP2702I-D-K9    f0:7f:06:30:92:8c         3rd Floor  1     IN       2
    FAL-3-AP05           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:f4         3rd Floor  1     IN       3
    Site Name........................................ RAHEJA-AP-GROUP
    Site Description................................. RAHEJA-AP-GROUP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    --More-- or (q)uit
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     5               raheja-interface     Disabled                          None
     2               raheja-guest         Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    FAL-RAHEJA-AP04      2     AIR-CAP2702I-D-K9    f0:7f:06:8d:24:1c  Near Meeting Roo  1     IN       3
    FAL-RAHEJA-AP02      2     AIR-CAP2702I-D-K9    f0:7f:06:8d:37:3c   Confrennce Room  1     IN       3
    FAL-RAHEJA-AP03      2     AIR-CAP2702I-D-K9    f0:7f:06:30:93:48  Near Confrence R  1     IN       3
    FAL-RAHEJA-AP05      2     AIR-CAP2702I-D-K9    f0:7f:06:bf:ae:c0  Near Meeting Roo  1     IN       3
    FAL-RAHEJA-AP06      2     AIR-CAP2702I-D-K9    f0:7f:06:92:b3:a0  Near Server Room  1     IN       3
    FAL-RAHEJA-AP01      2     AIR-CAP2702I-D-K9    f0:7f:06:92:b3:20    Reception Area  1     IN       3
    FAL-RAHEJA-AP08      2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:68  USER BAY ROAD si  1     IN       1
    FAL-RAHEJA-AP09      2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:d4     Training Room  1     IN       1
    --More-- or (q)uit
    Site Name........................................ default-group
    Site Description................................. <none>
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     1               group for mumbai     Disabled                          None
     2               guest wifi           Disabled                          None
     3               gurgaon-interface    Disabled                          None
     4               gurgaon-guest        Disabled                          None
     5               raheja-interface     Disabled                          None
     6               test                 Disabled                          None
    Cisco Controller) >show flexconnect group summary
    FlexConnect Group Summary: Count: 4
    Group Name                # Aps
    Gurgaon-AP                         9
    HQ-3RD-FLR-AP-GROUP                        12
    HQ-7THFLR-AP-GROUP                         14
    Raheja-AP-Group                            8
    (Cisco Controller) >show flexconnect group detail Gurgaon-AP
    Number of AP's in Group: 9
    bc:16:65:13:71:00    GUR-AP-03     Joined    Flexconnect
    f4:4e:05:45:78:98    GUR-AP-08     Joined    Flexconnect
    f4:4e:05:78:ae:64    GUR-AP-04     Joined    Flexconnect
    f4:4e:05:78:ae:e4    GUR-AP-01     Joined    Flexconnect
    f4:4e:05:80:b3:2c    GUR-AP-02     Joined    Flexconnect
    f4:4e:05:80:b3:e0    GUR-AP-06     Joined    Flexconnect
    f4:4e:05:80:b3:f8    GUR-AP-07     Joined    Flexconnect
    f4:4e:05:80:b4:44    GUR-AP-09     Joined    Flexconnect
    f4:4e:05:80:b5:18    GUR-AP-05     Joined    Flexconnect
    Efficient AP Image Upgrade ..... Disabled
    Master-AP-Mac     Master-AP-Name                    Model      Manual
    Group Radius Servers Settings:
    Type           Server Address    Port
                                             Primary       Unconfigured      Unconfigured
                                                                                          Secondary     Unconfigured      Unconfigured
    --More-- or (q)uit
    Group Radius AP Settings:
    AP RADIUS server............ Disabled
    EAP-FAST Auth............... Disabled
    LEAP Auth................... Disabled
    EAP-TLS Auth................ Disabled
    EAP-TLS CERT Download....... Disabled
    PEAP Auth................... Disabled
    Server Key Auto Generated... No
    Server Key..................     <hidden>
    Authority ID................ 436973636f0000000000000000000000
    Authority Info.............. Cisco A_ID
    PAC Timeout................. 0
    Multicast on Overridden interface config: Disabled
    DHCP Broadcast Overridden interface config: Disabled
    Number of User's in Group: 0
    Vlan :........................................... 203
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 205
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 204
    --More-- or (q)uit
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 206
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 207
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 208
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 209
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 210
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 211
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 212
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    --More-- or (q)uit
    Vlan :........................................... 216
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 217
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 218
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Group-Specific FlexConnect Wlan-Vlan Mapping:
    WLAN ID     Vlan ID
    WLAN ID   SSID                            Central-Dhcp  Dns-Override  Nat-Pat
    (Cisco Controller) >
    (Cisco Controller) >show wlan summary
    Number of WLANs.................................. 6
    WLAN ID  WLAN Profile Name / SSID               Status    Interface Name        PMIPv6 Mobility
    1        FRACTAL-EMP-MUMBAI / FRACTAL           Enabled   group for mumbai      none
    2        FRACTAL-GUEST / FRACTAL-GUEST          Enabled   guest wifi            none
    3        FRACTAL-EMP-GURGAON / FRACTAL-GURGAON  Enabled   gurgaon-interface     none
    4        GURGAON-GUEST / FRACTAL-GUEST-GURGAON  Enabled   gurgaon-guest         none
    5        RAHEJA-EMP-WIRELESS / FRACTAL-R        Enabled   raheja-interface      none
    6        TEST-SSID / TEST-SSID                  Enabled   test                  none
    hope this will give you proper understanding.  

  • WLC 5508 with LAP-1142n - Several Errors

    Hello all,
    I had installed a WLC 5508 with 7 LAP 1142n and 2 converted AP 1131abg.
    I am seeing some errors relating 2 issues.
    1st- One particular AP 1142 is disassociating and reseting the radios.
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman","serif";}
    Thu Oct 28 11:50:49 2010
    AP's Interface:0(802.11b)   Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
    Thu Oct 28 11:50:49 2010
    AP's Interface:0(802.11b)   Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
    Thu Oct 28 11:50:49 2010
    AP's Interface:1(802.11a)   Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
    Thu Oct 28 11:50:49 2010
    AP's Interface:1(802.11a)   Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
    Thu Oct 28 11:50:46 2010
    AP's Interface:1(802.11a) Operation   State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to Init.   Status:NA
    Thu Oct 28 11:50:46 2010
    AP's Interface:0(802.11b)   Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to   Init. Status:NA
    Thu Oct 28 11:50:46 2010
    AP 'AP3', MAC:   e8:04:62:23:ac:e0 disassociated previously due to AP Reset. Uptime: 1 days,   10 h 24 m 23 s . Last reset reason: operator changed 11g mode.
    Thu Oct 28 11:50:35 2010
    AP Disassociated. Base Radio   MAC:e8:04:62:23:ac:e0
    Thu Oct 28 11:50:35 2010
    AP's Interface:1(802.11a)   Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
    Thu Oct 28 11:50:35 2010
    AP's Interface:0(802.11b) Operation   State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
    I had some search, and the new discovery cause, might be that the AP didnt know what WLC do associate, in a multi-controller environment. This is not the case. I only have one WLC in the same management vlan.
    2st-The Radius server is beeing related in the logs as been deactivated. I raise the server time-out on Radius configuration option, but it still continues to do it.
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman","serif";}
    Thu Oct 28 10:24:41 2010
    RADIUS server 10.67.128.36:1812 deactivated in global list
    Thu Oct 28 10:24:41 2010
    RADIUS server 10.67.128.36:1812 failed to respond to request (ID 172)   for client e8:06:88:51:c0:2b / user 'unknown'
    Is this meaning the WLC stop sending request to the Radius Server ? We dont have BackUp Radius.
    As far as i know, its always the same mac-address client that is associated to that error, maybe a iphone.
    I had so many clients in that SSID and they are all working good.
    The Radius server is a NPS from windows Server 2008
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman","serif";}
    , and the client says that the medium response time is 0,02 sec, so im wondering why the controller is not getting response from Radius for a particular client?! My client also says, that didnt found any log related to that mac-address client ... what is weird...
    WLC with last software available 7.0.164
    Hope some one help me here.
    Best Regards,
    Bruno Petrónio

    Thanks Scott,
    I understand what you are mentioning, and i really didnt do it yet.
    I realize that the primary controller was not configured on the
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman","serif";}
    Wireless –> All APs –> High Availability tab, and did it only to the AP that is taking this beahviour.
    Is this mandatory for a 1 controller only ?
    No mather what the manual say, after that the AP is rebooting 2 mins in 2 mins... with the same kind of messages.
    The interface on the switch is getting a few input errors and the same numbers of crc... but are so few...
    Next step ... i will change it to another one's place/pathing cable.
    Regarding the Radius messages... any ideas ?
    I'm already on 30 sec's of server timeout.
    Best Regards,
    Bruno Petrónio

  • WLC 5508 with version 7.0.98.0 and AIR-LAP1242ag

    hi, recently i have deployed wlc 5508 with ap 1262. initially i had trouble with the existing version on the wlc (6..0.199.0) which AIR-LAP1262N-E-K9 was not registering with wlc. i have upgraded the wlc to 6.0.199.4 ver still it was not registering. finally i have upgraded to 7.0.98.0 and all the 40 AP's ( AIR-LAP1262N-E-K9 ) are addedd and its working fine.
    Now my issue is, at the same site i have 12 nos of AIR-LAP1242ag autnomous AP's which i need to convert to lightweight ap and register with wlc. where i am stuck currently. after loading the recovery image (c1240-rcvk9w8-tar.123-7.JX9.tar) the ap reboots and can see it register with wlc within seconds contollers pushed the new image and once the ap reboots, never register again.
    does anyone has any idea?

    After adding the country codes GB and RU.. in my test setup 1242 is registered...i will have it run for couple hours and see the result
    ref: below
    (Cisco Controller) >show ap uptime
    Number of APs.................................... 2
    Global AP User Name.............................. Not Configured
    Global AP Dot1x User Name........................ Not Configured
    AP Name              Ethernet MAC       AP Up Time               Association Up Time
    AP1cdf.0f66.79ca     1c:df:0f:66:79:ca  0 days, 00 h 43 m 35 s   0 days, 00 h 42 m 36 s
    AP001e.be27.a7e6     00:1e:be:27:a7:e6  0 days, 00 h 16 m 56 s   0 days, 00 h 07 m 15
    This issue sorted...thanks

  • Cisco WLC 5508 not sending SNMP Traps

    Hello Everyone.
    I'm having a weird error on our WLC environment. We have an HA with two cisco WLC 5508 and i cannot get SNMP Traps working on a Windows PC running Kiwi Syslog server (free ed.).
    I can receive correctly Syslog messages, but not traps.
    I Tried also to send SNMP Traps from WLC to a different PC using Linux with snmptrapd and it works fine.
    I tried then to send from my Linux box a snmp trap to my Windows PC, and it works fine, but i still cannot receive anything from WLC.
    Using Wireshark to detect traffic, i cannot see any packet on udp port 162.
    I cannot figure out any problem with my scenario, but i can see the following errors on syslog:
    *rmgrTrasport: Mar 30 16:08:22.602: #RMGR-3-INVALID_PING_RESPONSE: rmgr_utils.c:270 Ping response from <my_windows_PC> is invalid. Ip address do not match.
    My WLC Version is 7.6.130.0
    Thank you for your support.

    I have gone through your query and found the following fruitful links ,please let me know if it helps and mark it correct answer if it is.
    https://www.manageengine.com/network-monitoring/help/userguide/processing_traps.html
    https://rscciew.wordpress.com/2014/10/12/snmp-configuration-on-wlc/
    Thanks :)

  • Cisco WLC 5508 - NPS Radius

    Cisco WLC 5508
    Software Version: 7.4.100.0
    Windows Server 2008R2
    I've got everything setup on the Windows Server 2008 side of things (certificates, radius clients, etc)
    I added the radius server on the WLC, and configured a new WLAN to use it.
    Both are on the same subnet.
    When trying to conect to the WLAN it kept failing.  I installed wireshark on the server to monitor the radius traffic, and to my surprise there was no radius traffic showing up on the server.  The radius statistics on the WLC are at 0 as well, so it's like the WLC isn't even attempting Radius.
    I reverified that the server was enabled on both the security tab and the WLAN itself on the WLC.  Rebooted the controller and the server, all to no avail.  I used a radius test client, and can successfully send radius commands to the server using that utility.
    Frustrated, I just kept trying to reconnect on my wireless device, and after about the 15th try, finally I saw radius activity on wireshark.  It rejected my access, but at least I saw activity.  It also registerd radius statistcs on the WLC as well.
    So now if I keep trying to connect repeatedly, about every dozen or so times the WLC actually will send a radius request to the server.
    What in the world is going on here?

    I do have local management users on the controller.
    Some hours later I added the option of authenticating management users, for the NPS server. Then logged inn to the management GUI using NPS radius, worked just fine.
    However, these commands have been useful to me several times, to make sure unsuccessful requests appear in the Windows Event log:
    auditpol /get /subcategory:"Network Policy Server"
    If it shows ‘No auditing’ or just "Success", you can run this command to enable it:
    auditpol /set /subcategory:"Network Policy Server" /success:enable /failure:enable
    So now I know that the NPS radius server works, for management access. I will go to the customer's site some other day to test it for 802.1x authentication. If not, I'll do some debugging to decide wihich to blame - the WLC or NPS.

  • Cisco WLC 5508 and AP 2702i

    Hello,
    i'm tryin to install a WLC 5508 with version 7.6.120 and with AP 2702i with the follwing firmware ap3g2-rcvk9w8-xx ( 15.2(4)JB5), i've configured saticly the capwapp with the follwwing configuration:
    IP Address         172.17.255.234
    IP netmask         255.255.0.0
    Default Gateway    172.17.255.254
    Primary Controller 172.17.255.239
    The controller iw the IP 172.17.255.239 and i've connectivity between the both equipments, there's no firewalls between them, however i can't register the AP with the controller, anyone have some idea?

    Hi,
    May be AP comes with mesh image: You cans ee in logs
    If it is with mesh image then use this:
    1. Log into your Wireless LAN Controller.
    Select the Security tab.
    Expand AAA and select AP Policies.
    Click the Add button in the far right.
    Under Add AP to Authorization List, enter the MAC Address of the Access Point in the MAC Address text box.
    Click the Add button.
    Click the Apply button
    Now your AP must be in downloding state.
    2. When the AP finally show up under the Wireless tab, check the AP Mode . It may operating in ‘Bridge’ mode. This is incorrect. It should be in ‘Local’ mode.
    If your AP is in ‘Bridge’click the name of the AP under the AP Name column. Under the General tab, click the AP Mode drop down box and select ‘Local’. Click the Apply button in the top right.
    Now AP should now be working fine.
    Hope it helps.
    Regards
    Dont forget to rate helpful posts

  • Cisco WLC 5508 in HA mode error

    Hai ,
    I am Getting the below Error in Cisco WLC 5508, Version 7.4.100.0 in HAmode. The WLC contains Access Points having in local and Flex Connect Mode.
    RF failure notification ErrorType: 32 Reason :Error: Config Sync failed on Standby for the usmdb:HA_send_usmDbApfMsDelete,
    I sam a same bug in Cisco WLC 7.4.100.0 release notes similar to the error like
    RF failure notification ErrorType: 32 Reason :Error: Config Sync failed on Standby for the usmdb:HA_send_usmDbSpamSetRadSlotAntennaType.
    Any Ideas?

    HI Mohamed,
    its a open Caveats  in 7.4.100.0
    CSCud26632
    Symptom: The following SNMP trap appears on the controller when you change the channel width number to 40-MHz:
    RF failure notification ErrorType: 32 Reason :Error: Config Sync failed on Standby for the usmdb:HA_send_usmDbSpamSetRadSlotAntennaType.
    Conditions: Controller is in an HA pair. Join the 802.11n access point to the controller and change the channel width to 40-MHz and channel number to 157.
    Workaround: None
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn74.html
    Reagrds
    Please rate helpful posts

  • Need Information of cisco WLC 5508 LAG Interface

    HI
    We have cisco WLC 5508 in our network and right now ,this WLC is connected to two ports of each core switches.Both CORP and GUEST SSID are configured on this WLC.
    Now we want to segregate the trafffic og GUEST to on core switches from WLC. SO my question is ,how can we achieve this without using guest anchor controller ?
    Can i use one interfcae cisco WLC 5508 and connect it to the firewall or any device ?
    Thanks
    Puneet

    Hi
    Thanks ...I am using WLC as a DHCP server for Guest.
    So  i want to know ,is there any requirement that GUEST subnet should be pingable from WLC management IP address.
    my topology is here...
    Corp network and management network are reachable however management metwork is not pinagble from guest netowrk.

  • Error APF_HA-3-SYNC_RETRANSMIT_FAIL - Controller Cisco WLC 5508

    hello,
    I have two controllers on Cisco WLC 5508 HA version 7.5.
    I'm having several sync error logs:
    *haSSOServiceTask3: Jan 22 09:22:51.637: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (00:0b:6b:b3:d4:6b )data sync. Retry after 300 secs.
    *haSSOServiceTask4: Jan 22 09:22:51.037: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (60:67:20:fa:19:04 )data sync. Retry after 300 secs.
    *haSSOServiceTask2: Jan 22 09:22:50.838: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (04:fe:31:3b:7d:ca )data sync. Retry after 300 secs.
    *haSSOServiceTask2: Jan 22 09:22:50.838: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (88:9b:39:c3:cf:42 )data sync. Retry after 270 secs.
    *haSSOServiceTask3: Jan 22 09:22:50.838: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (18:e2:c2:c0:9b:5b )data sync. Retry after 300 secs.
    *haSSOServiceTask0: Jan 22 09:22:50.837: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (08:70:45:77:36:60 )data sync. Retry after 240 secs.
    *haSSOServiceTask0: Jan 22 09:22:50.837: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (20:64:32:cb:13:a8 )data sync. Retry after 180 secs.
    *haSSOServiceTask0: Jan 22 09:22:50.837: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (8c:70:5a:2e:36:e0 )data sync. Retry after 300 secs.
    *haSSOServiceTask4: Jan 22 09:22:50.837: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (58:94:6b:65:ad:0c )data sync. Retry after 300 secs.
    *haSSOServiceTask1: Jan 22 09:22:50.836: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (40:2b:a1:53:8d:a9 )data sync. Retry after 300 secs.
    *haSSOServiceTask4: Jan 22 09:22:50.836: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (a4:17:31:16:19:2c )data sync. Retry after 300 secs.
    *haSSOServiceTask1: Jan 22 09:22:50.836: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (04:1e:64:7e:19:31 )data sync. Retry after 300 secs.
    *haSSOServiceTask4: Jan 22 09:22:50.639: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (60:67:20:33:7c:74 )data sync. Retry after 300 secs.
    *haSSOServiceTask4: Jan 22 09:22:50.639: #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2939 Maximum retransmission exceeded for client (00:26:c6:57:61:34 )data sync. Retry after 300 secs.
    Has anyone had something similar?

    Hi Valerio, did you ever find out what this error was. I am seeing the same  error but on 7.6
    #APF_HA-3-SYNC_RETRANSMIT_FAIL: apf_ha.c:2966 Maximum retransmission exceeded for client (8c:00:6d:16:7b:3d )data sync

  • Configuration of Cisco WLC 2504 with Local LAN static IP and DHCP

    I want to configure Cisco WLC 2504 with Local LAN static IP and WLC 2504 with DHCP so that APs can be connect with controller.
    Currently i am using WLC 2504 with DHCP so can anyone suggest how to do that..

    Hi Sandeep
    The info is correct, if we're using code below 7.3.101.0.
    This issue is fixed via the below bug id.
    CSCto01390 Unable to ping AP's directly connected to a 2500 controller
    check the fix that is updated on 7.4, 7.5 RNE.
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn75.html
    Note
    Directly connected APs are supported only in Local mode.
    http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps11630/data_sheet_c78-645111.html
    For quick and easy deployment Access Points can be connected directly to 2504 Wireless LAN Controller via two PoE (Power over Ethernet) ports
    Thanks
    Saravanan

  • Cisco ISE 1.2 & Cisco WLC 5508 v7.6

    Hi all,
    we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
    Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
    I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
    Thanks all
    Mario De Rosa

    Hi Neno,
    right I have this almost working now.
    I have simplified the setup. I am not going to do any client provisioning at the moment.
    So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
    Now I am trying to introduce the posture element & per user ACLs.
    I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
    DNS resolution seems to be working fine.
    VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
    VLAN10 is the branch DATA VLAN.
    below is some output to give you some more details...
    (Cisco Controller) >show client detail 00:24:d6:97:b3:be
    Client MAC Address............................... 00:24:d6:97:b3:be
    Client Username ................................. [email protected]
    AP MAC Address................................... 18:33:9d:f0:21:80
    AP Name.......................................... test-flex-ap
    AP radio slot Id................................. 0
    Client State..................................... Associated
    Client NAC OOB State............................. Access
    Wireless LAN Id.................................. 2
    Hotspot (802.11u)................................ Not Supported
    BSSID............................................ 18:33:9d:f0:21:81
    Connected For ................................... 128 secs
    Channel.......................................... 6
    IP Address....................................... 10.130.130.120
    Gateway Address.................................. 10.130.130.1
    Netmask.......................................... 255.255.255.0
    IPv6 Address..................................... fe80::f524:1910:69f0:9482
    Association Id................................... 1
    Authentication Algorithm......................... Open System
    Reason Code...................................... 1
    Status Code...................................... 0
    Client CCX version............................... 4
    Client E2E version............................... 1
    --More-- or (q)uit
    Re-Authentication Timeout........................ 1651
    QoS Level........................................ Silver
    Avg data Rate.................................... 0
    Burst data Rate.................................. 0
    Avg Real time data Rate.......................... 0
    Burst Real Time data Rate........................ 0
    802.1P Priority Tag.............................. disabled
    CTS Security Group Tag........................... Not Applicable
    KTS CAC Capability............................... No
    WMM Support...................................... Enabled
      APSD ACs.......................................  BK  BE  VI  VO
    Power Save....................................... OFF
    Current Rate..................................... m13
    Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
        ............................................. 12.0,18.0,24.0,36.0,48.0,
        ............................................. 54.0
    Mobility State................................... Local
    Mobility Move Count.............................. 0
    Security Policy Completed........................ No
    Policy Manager State............................. POSTURE_REQD
    Policy Manager Rule Created...................... Yes
    AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
    AAA Override ACL Applied Status.................. Yes
    --More-- or (q)uit
    AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
    AAA Override Flex ACL Applied Status............. Yes
    AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
    Audit Session ID................................. c8dc800a00000005b3e7e953
    AAA Role Type.................................... none
    Local Policy Applied............................. none
    IPv4 ACL Name.................................... none
    FlexConnect ACL Applied Status................... Yes
    IPv4 ACL Applied Status.......................... Unavailable
    IPv6 ACL Name.................................... none
    IPv6 ACL Applied Status.......................... Unavailable
    Layer2 ACL Name.................................. none
    Layer2 ACL Applied Status........................ Unavailable
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ none
    No. of mDNS Services Advertised.................. 0
    Policy Type...................................... WPA2
    Authentication Key Management.................... 802.1x
    Encryption Cipher................................ CCMP (AES)
    Protected Management Frame ...................... No
    Management Frame Protection...................... No
    EAP Type......................................... EAP-TLS
    FlexConnect Data Switching....................... Local
    --More-- or (q)uit
    FlexConnect Dhcp Status.......................... Local
    FlexConnect Vlan Based Central Switching......... No
    FlexConnect Authentication....................... Central
    Quarantine VLAN.................................. 0
    Access VLAN...................................... 220
    Client Capabilities:
          CF Pollable................................ Not implemented
          CF Poll Request............................ Not implemented
          Short Preamble............................. Implemented
          PBCC....................................... Not implemented
          Channel Agility............................ Not implemented
          Listen Interval............................ 10
          Fast BSS Transition........................ Not implemented
    Client Wifi Direct Capabilities:
          WFD capable................................ No
          Manged WFD capable......................... No
          Cross Connection Capable................... No
          Support Concurrent Operation............... No
    Fast BSS Transition Details:
    Client Statistics:
          Number of Bytes Received................... 33698
          Number of Bytes Sent....................... 19397
          Total Number of Bytes Sent................. 19397
    --More-- or (q)uit
          Total Number of Bytes Recv................. 33698
          Number of Bytes Sent (last 90s)............ 19397
          Number of Bytes Recv (last 90s)............ 33698
          Number of Packets Received................. 283
          Number of Packets Sent..................... 147
          Number of Interim-Update Sent.............. 0
          Number of EAP Id Request Msg Timeouts...... 0
          Number of EAP Id Request Msg Failures...... 0
          Number of EAP Request Msg Timeouts......... 0
          Number of EAP Request Msg Failures......... 0
          Number of EAP Key Msg Timeouts............. 0
          Number of EAP Key Msg Failures............. 0
          Number of Data Retries..................... 53
          Number of RTS Retries...................... 0
          Number of Duplicate Received Packets....... 2
          Number of Decrypt Failed Packets........... 0
          Number of Mic Failured Packets............. 0
          Number of Mic Missing Packets.............. 0
          Number of RA Packets Dropped............... 0
          Number of Policy Errors.................... 0
          Radio Signal Strength Indicator............ -42 dBm
          Signal to Noise Ratio...................... 41 dB
    Client Rate Limiting Statistics:
    --More-- or (q)uit
          Number of Data Packets Recieved............ 0
          Number of Data Rx Packets Dropped.......... 0
          Number of Data Bytes Recieved.............. 0
          Number of Data Rx Bytes Dropped............ 0
          Number of Realtime Packets Recieved........ 0
          Number of Realtime Rx Packets Dropped...... 0
          Number of Realtime Bytes Recieved.......... 0
          Number of Realtime Rx Bytes Dropped........ 0
          Number of Data Packets Sent................ 0
          Number of Data Tx Packets Dropped.......... 0
          Number of Data Bytes Sent.................. 0
          Number of Data Tx Bytes Dropped............ 0
          Number of Realtime Packets Sent............ 0
          Number of Realtime Tx Packets Dropped...... 0
          Number of Realtime Bytes Sent.............. 0
          Number of Realtime Tx Bytes Dropped........ 0
    Nearby AP Statistics:
          test-flex-ap(slot 0)
            antenna0: 14 secs ago.................... -51 dBm
            antenna1: 14 secs ago.................... -37 dBm
          test-flex-ap(slot 1)
            antenna0: 14 secs ago.................... -51 dBm
            antenna1: 14 secs ago.................... -54 dBm
    --More-- or (q)uit
    DNS Server details:
          DNS server IP ............................. 10.0.17.31
          DNS server IP ............................. 10.0.17.43
    Assisted Roaming Prediction List details:
     Client Dhcp Required:     False
    Allowed (URL)IP Addresses
    (Cisco Controller) >
    (Cisco Controller) >show wlan 2
    WLAN Identifier.................................. 2
    Profile Name..................................... Demo1x
    Network Name (SSID).............................. Demo1x
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Enabled
    Network Admission Control
    Client Profiling Status
        Radius Profiling ............................ Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
        Local Profiling ............................. Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
      Radius-NAC State............................... Enabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    --More-- or (q)uit
    Number of Active Clients......................... 1
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    User Idle Timeout................................ Disabled
    Sleep Client..................................... disable
    Sleep Client Timeout............................. 12 hours
    User Idle Threshold.............................. 0 Bytes
    NAS-identifier................................... mario-test-flex-vwlc
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    WLAN Layer2 ACL.................................. unconfigured
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    Quality of Service............................... Silver
    Per-SSID Rate Limits............................. Upstream      Downstream
    Average Data Rate................................   0             0
    --More-- or (q)uit
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Per-Client Rate Limits........................... Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    --More-- or (q)uit
    Radius Servers
       Authentication................................ 10.0.16.111 1812
       Accounting.................................... 10.131.16.111 1813
          Interim Update............................. Disabled
          Framed IPv6 Acct AVP ...................... Prefix
       Dynamic Interface............................. Disabled
       Dynamic Interface Priority.................... wlan
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       FT Support.................................... Disabled
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Disabled
             AES Cipher.............................. Enabled
                                                                   Auth Key Management
             802.1x.................................. Enabled
             PSK..................................... Disabled
             CCKM.................................... Disabled
    --More-- or (q)uit
             FT-1X(802.11r).......................... Disabled
             FT-PSK(802.11r)......................... Disabled
             PMF-1X(802.11w)......................... Disabled
             PMF-PSK(802.11w)........................ Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-DS mode........................ Enabled
          GTK Randomization.......................... Disabled
          SKC Cache Support.......................... Disabled
          CCKM TSF Tolerance......................... 1000
       WAPI.......................................... Disabled
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       FlexConnect Local Switching................... Enabled
       flexconnect Central Dhcp Flag................. Disabled
       flexconnect nat-pat Flag...................... Disabled
       flexconnect Dns Override Flag................. Disabled
       flexconnect PPPoE pass-through................ Disabled
    --More-- or (q)uit
       flexconnect local-switching IP-source-guar.... Disabled
       FlexConnect Vlan based Central Switching ..... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional
       PMF........................................... Disabled
       PMF Association Comeback Time................. 1
       PMF SA Query RetryTimeout..................... 200
       Tkip MIC Countermeasure Hold-down Timer....... 60
       Eap-params.................................... Disabled
    AVC Visibilty.................................... Disabled
    AVC Profile Name................................. None
    Flow Monitor Name................................ None
    Split Tunnel (Printers).......................... Disabled
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Disabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Assisted Roaming Prediction Optimization......... Disabled
    802.11k Neighbor List............................ Disabled
    802.11k Neighbor List Dual Band.................. Disabled
    Band Select...................................... Disabled
    --More-- or (q)uit
    Load Balancing................................... Disabled
    Multicast Buffer................................. Disabled
     Mobility Anchor List
     WLAN ID     IP Address            Status
    802.11u........................................ Disabled
    MSAP Services.................................. Disabled
    Local Policy
    Priority  Policy Name
    (Cisco Controller) >
    when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
    (Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1) 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE  statusCode is 0 and status is 0 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates  statusCode is 0 and gotSuppRatesElement is 1 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name: 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
    *spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
        MAC: 00:24:d6:97:b3:be, source 4
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410:      [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for  mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header: 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00                                       .._.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410:      [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header: 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00                                       .._.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
    apfMsEntryType = 0 apfMsEapType = 13
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 ACL ID = 255, IPv
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 ACL ID = 255, 
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
    apfMsEntryType = 0 pmkLen = 32
    *DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
      type = Airespace AP Client - ACL passthru
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 A
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile 
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
    *pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
    *IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
    *IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
    *DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    Can you see any obvious reason why the NAC agent wont pop up?
    Thanks
    Mario

Maybe you are looking for

  • Why did my iPod stop working?

    My new fifth gen ipod is barely a few weeks old and already is having trouble. Previously it wouldn't turn on, and resetting it worked, but now the same thing is happening but without anything working. I tried the five R's and EVERYTHING else the app

  • Final Cut Pro 7 - Share - Blu-ray - ERROR

    Fresh install of OS and FCS. Ran a quick test to make sure this would work: File - Share - Blu-ray Burned to disc then and there, and it was successful on an eleven second portion of the clip with an in and out point on the timeline. The result was a

  • How to create Factory Default Recovery Disc with OneKey Recovery 4.0

    I have a K430 and before I use it it (as with any machine I have bought) I wanted to make my recovery disc(s). Throughout this website there are guides to do this with version 7, but this desktop has version 4.0 of OKR I can save an image of my syste

  • Disable iSight camera and use external USA webcam

    We have a macbook and use a large monitor for managing brochures etc. I would like to mount an external USB webcam on the monitor and use it with Skype. However, whenever I open Skype it turns on the iSight camera (which is facing a wall). Is there a

  • Creating statistics based on two or more fields

    Hi! Curious if the functionality of Adobe Forms has the same possibilities with calculating stats based on several fields as one can do with Excel. For example, can I create a SUMPRODUCT formula to find all the replies that meet two or more critieria