Cisco Works Error

Hi ,
I have a Cisco work server and i am facing problem with the Netconfig job failure.It fails the job with following error.
" ERROR:RME_CDL1032:Synchronization of the running configuration before deply,has failed" and also i am seeing the following error as " cm0012:Unable to create new version on archive $1 " Action : Check if disk space is available and directory has required permission.
LMS version  : 2.6
RME Version : 4.0.5
Please let me know if you have any idea on this error.
Thanks in advance
Thanks & Regds,
Lalit

CM0012 error is a bug - "CSCsh39475    ConfigMgmt CM0012: Unable to create new version on archive". The patch is posted on CCO.

Similar Messages

  • Cisco Works error URN_NOT_FOUND : urn "JRM":Not found !!

    Hi,
    I have a Cisco works server running LMS 2.6 version.Server was working fine without any issues.Suddenly i started facing an issue when i try to create a Netconfig Job.The error i am facing  is " Error occured while processing.Possible Cause: URN_NOT_FOUND : urn "JRM":Not found !!   
    Also observed CWCS cmf database engine, dfmFh database engine and dfmInv database engine servives are not starting.The pdshow output is also not giving any output.It end with error GetReply failed.
    Please let me know if you have any idea on this error.
    Thanks & Regds,
    Lalit

    Hi Afroj,
    I have tried the procedure which you have mentioned but it didnt work.I tried removing the ctmregistry file and started the serices.But the Cisco works server still has issues.
    LMS is not integrated with ACS.Its a standalone server.(Non ACS )
    pdshow output does not give any output.It comes as error as " GetReply Failed " I am not getting any output from pdshow.
    Please find the attached screen shot of services.msc and common service home page.
    Please let me know if you have any suggestions.
    Thanks & Regds,
    Lalit

  • Cisco works error messages

    Posted by: alphaomegait - Aug 15, 2005, 7:00am PST
    I get messages this, “ InCharge Domain : DFM Clear: Router FALSE 172.16.1.17 PerformanceException - System is experiencing Port or Interface performance problems.”
    all day long from Cisco Works.
    I have not been able to find anything in technical support on the Cisco site to help with this. Can anyone give me a push in the right direction?
    Thanks up front.

    I think you have QOS setup on the interface it is possible that this is causing the drops and to rule it out we should try removing "service-policy output llq " from the interface and see if the drops still increment.

  • Error Message in Cisco Works

    I am running device troubleshooting in cisco works on a 1200 series acces point.
    I am getting the followinf error message:
    VTP Disconnected Domain DomainName:NO_VTP
    Do I need to upgrade IOS on all AP's??

    It seems like that Link in a VTP domain is not set to trunk. Verify the trunk.

  • Cisco 3945 Router error while adding in Cisco Works

    Hi,
    I have a Cisco 3945 Router and when we try to add the same into the Cisco Works it gives me an error saying " CM0056 Config fetch failed for 192.168.xx.xx Cause: CM0204 Could not create DeviceContext for 1238 Cause: CM0206 Could not get the config transport implementation for 192.168.xx.xx Cause: UNKNOWN Action: Check if required device packages are available in RME. Action: Check if protocol is supported by device and required device package is installed.
    We are using LMS version 2.6. Please let me know the latest router 3945 with support or not.
    Thanks in advance.
    Thanks & Regds,
    Lalit

    Hi Joe,
    Thanks for the quick reply.The following version we are using :
    LMS 2.6 , RME : 4.0.5.
    Is this confirm Joe that Older verison will not support new Cisco devices ie 3945 Router.Any documents will be more helpful with regard to the same.
    Thanks & Regds,
    Lalit

  • Cisco Works LMS 4.0 doesn´t start

    Hello All
    i have big trouble with me LMS 4.0 installation. I did an Upgrade from LMS 3.2 to LMS 4.0. After that the Works was running without any problems. After some days i´d tried to login on the LMS and it told me something like my lincens where corrupt or so. I´d tried to start the CiscoWorks Demon Manger but he didn´t start. OK after some investigation at the i-net i decided to perform a clean installation of the Server an Cisco Works.
    So after i do thes i´d perform a restore of my old Data from LMS 3.2. Now i investicated that my ANI Server Falied to start. OK than i tried to restart the Works Demon ... f... and what will happend ?!?!?! The demon doesn´t start. Can someone help me ?!?! Please i will not perform a new istallation again.
    C:\Windows\system32>net start crmdmgtd
    The CiscoWorks Daemon Manager service is starting.
    The CiscoWorks Daemon Manager service could not be started.
    The service did not report an error.
    More help is available by typing NET HELPMSG 3534.
    Thanks
    Mario
    Hi i have an update for this issues ... After i´d tried to start all Works- Services be hand ... all Services will start execpt the deamon ... When i loged in i get messages "License Server/Deamon Manager is down. Please  check license.log for more information."
    Thats the same situtaion befor the new installation.

    Hi Afroj
    i´d just have an update for you and maybe for Martin. I´d checked the services and investigate that the ANIDatabase Engine
    was not stoped. After i stoped the service "by Hand". I tried to reinalize the Database and see ... IT WORKS ...
    D:\CiscoWorks\CSCOpx\bin>perl.exe dbRestoreOrig.pl dsn=ani dmprefix=ANI
    WARNING: Existing contents of ani database will be lost.
    Do you want to continue [y/n]?y
    INFO: Starting the DataBase
        Starting database engine aniEng
    INFO: Process created
    INFO: Started the Database engine : aniEng Retry 0
    INFO: Started the Database engine : aniEng Retry 1
    INFO: Started the Database engine : aniEng Retry 2
    INFO: Started the Database engine : aniEng Retry 3
    INFO: Started the Database engine : aniEng Retry 4
    INFO: Started the Database engine : aniEng Retry 5
    INFO: Started the Database engine : aniEng Retry 6
    INFO: Started the Database engine : aniEng Retry 7
    INFO: Started the Database engine : aniEng Retry 8
    INFO: Started the Database engine : aniEng Retry 9
    INFO: Getting message
    INFO: Connect the database dsn=ani
    INFO: Connected the Database
    INFO: Command Executed
    INFO: Connecting the Database ani
    INFO: Company=Cisco Systems;Application=NMTG;Signature=010fa55157edb8e14d818eb4f
    e3db41447146f1571g32125eb777a87cbf8b29a954f559d4221b792ff8
    INFO: Preparing AUTH cmd
    INFO: AUTH Executed
    INFO: AUTH cmd finished
    INFO: Stopping the Database engine ani
        Stopping database engine aniEng
    INFO: File not exists.SQL Anywhere Command File Hiding Utility Version 10.0.1.40
    51
    INFO: Database [ani] authenticated successfully.
    ani database initialization is completed.
    D:\CiscoWorks\CSCOpx\bin>
    D:\CiscoWorks\CSCOpx\bin>pdshow ANIServer
            Process= ANIServer
            State  = Running with busy flag set
            Pid    = 11136
            RC     = 0
            Signo  = 0
            Start  = 8/22/2011 1:01:29 PM
            Stop   = Not applicable
            Core   = Not applicable
            Info   = ANIServer started.
    Many Thanks for your help ...
    Regards
    Mario

  • Cisco works LMS 3.0.1 does not archiever configuration for cisco 7201 router

    Hi All,
    We have Cisco works LMS 3.0.1 and it does not archiever configuration for cisco 7201 router.
    Any help would be appriciated.
    Thanks in advance
    Samir

    Hi,
    *** Device Details for d0151-100 ***
    Protocol ==> Unknown / Not Applicable
    Selected Protocols with order ==> TFTP,SSH,HTTPS
    Execution Result:
    Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
    This is the error while doing syn archieve.
    I am not sure about Rtr7000 version but we have latest Rtr7000.
    Waiting for your kind reply.
    Samir

  • Cisco Works LMS HUM issue

    Hi,
    I am using Cisco works LMS 3.1 with HUM 1.1.0. I am receiving thresold and job schedule mail alert from HUM.
    It is showing error in JOB history  “Not able to connect the mail server” while alerts from RME,IPM,CS,DFM are coming on mail.
    I have Configured HUM just 3 days back and all others application had been configure 4 months back.
    Please help.
    Regards,
    DJ

    Hi Clarke,
    Thanks for response. Please see the attached HUM smtp error. I have tried the HUM JOB with sniffer to filter smtp port 25 traffic but nothing is reflecting
    in sniffer when trying to send mail through HUM while DFM,RME IPM mail are showing in sniffer and we are getting mail as well.
    I have upgraded HUM version from 1.1.0 to 1.1.2 but the error is same.
    Regards,
    Dinesh Joshi

  • Cisco Works tftp download config

    I have a Cisco Works server that appears to be backing up config files from the routers.  If I needed to restore a startup-config, how do I do it?
    I tried "copy tftp start"
    But I have no idea what it has named the file, where it is stored, it appears to be stored here:
    E:\PROGRA~1\CSCOpx\files\rme\dcma
    But I could be wrong about that, there is an extremely convoluted file directory scheme there that seems to have numbered the devices and has multiple backups of each with no common router name to see.
    tells me:
    %Error opening tftp://*.*.*.*/router-confg (Permission denied)
    Probably have the wrong file name since I can not figure out what the file name is supposed to be or where it is.

    Ok, figured it out:
    %Program Files%\CSCOpx\tftpboot
    TFTP server will allow you to download any file in the above directory.

  • Cisco works windows 2000 server (IDS)

    I installed cisco works prepared for monitoring IDS Sensor, but i have some problem Access Apache windows folders
    Error: The requested URL cannot be reached because client denied by server configuration: c:/program files/cscopx/htdocs/csconm
    Description: 403 Forbidden is the HTTP status code returned by the Apache web server when either the user or the server itself has insufficient access rights to the URL.
    You are not allowed access to this URL due to insufficient access rights. This may be due to an incorrect installation of the product. Please refer to your product's installation guide.

    Please try the following:
    Stop Daemon Manager. Type in "c:\net stop crmdmgtd " in the Windows command line
    Then go to: NMSROOT\lib\web\conf\allow_files.conf (where NMSROOT is Progra~1\CSCOpx)
    Please check if this file has the following entries
    /index.html
    /login.html
    /mainPanel.html
    /JSP/cmf/admin/index.jsp
    /login1.html
    Afterwards, restart Daemon Manager. Type in "c:\ net start crmdmgtd" in the CLI.
    And try to access the server again.
    HTH,
    -J

  • Cisco Works SNMP write community string Incorrect

    Hi,
    I have installed Cisco Works at my organisation. Under RME -> Inventory -> Import status -> Device Attribute Error: I am getting: Incorrect SNMP write community strings. Even though i know perfectly well the SNMP write community string is correct. To prove that, if I delete the device and then add the same device using the same SNMP write community string it works fine. then a couple of days later, it comes up with the same message "SNMP write community string is incorrect". I have increased the time and retries for the SNMP settings at the ANI server, still it has not resolved the issue.
    Please help

    I have sharched the CCO bug toolkit and according them, it was a know issue for verion 3.4 but it has been fixed for Ver RME 3.5. But we are currently running RME 3.5, therefore it does not make any sense.

  • Cisco Works LMS R3.1 with ACS R5.1

    I search on internet about the AAA integration between LMS R3.1 y ACS R5.1, and all the information that I found it's related to ACS R4.1. It's possible to integrate with ACS R5.1.
    Regards and thanks in advanced
    Luis Martinez

    Nael,
    Sorry to batter you, but I was trying to migrate my Cisco Works LMS R3.1 to R3.2 and from the support page of CISCO I just can donwload the following version LMS R3.2.1 (LMS R3.2 service pack 1). I tried to install that version but i got an error that saids "LMS R3.2.1 needs LMS R3.2 installed on the server"
    Could you please tell me where can I download the complete and initial LMS R3.2.
    Thanks in advanced for your kindly help.
    Luis Martinez

  • Problems Installing Cisco Works 4.2 Evaluation Version

    Hello, I'm trying to test Cisco Works LAN Management Solution 4.2
    I have a partition in my laptop to test this software but after the installation process i'm unable to access via http to the server,
    I does not display anything.
    Please help me!

    Doublecheck your prerequisites as Vinod suggested. LMS is very particular about you meeting ALL the prerequisites exactly. If some are missing it will notify you during installation. Others may not generate an error but will leave you with a non-working setup.
    When you machine starts, it takes as long as 15-20 minutes for LMS to be fully functional. There are many background processes started by the daemon manager. There is a shortcut to see if all are finished starting by watching for the "ready" folder (NMSROOT\objects\dmgt\ready is the default location) to be empty. As CiscoWorks LMS starts up, that folder will at various times have lock files put into it as the processes start.
    The pdshow command enumerates the status all of the background processes.
    Yes, NMSROOT is the parent folder for your installation. The default location for NSMROOT in Windows is under C:\Program Files\CSCOpx. You can confirm on your installation by checking your environment variables under Windows Server.

  • IDS & Cisco Works SIMS

    Hello,
    I try to integrate a IDS 4.1 appliance to Cisco Works SIMS 3.1 (Netforensics) . But I fail for 2 days now. I can see that the CSIDS4 agent tries to connect to the IDS sensor with TCP port 443 but in the logs I always can see a "failed to conntect host".
    I configured the "NF CSIDS Agent":
    "Date Processor Data1" -> "CSIDS4 AGENT PROTOCOL" -> "MODE = SECURE"
    There is a field: "signature"
    Do I need fill out that field? What is the correct input for that field?
    Or ist "mode" secure the wrong mode?
    Has anybody integrated a Cisco IDS 4.1 to NetForensics 3.1 successfully?
    PLEASE HELP!
    Thanks a lot
    Markus

    Hello,
    On the IDS Sensor I found that error events:
    evError: eventId=1050261859615885102 severity=error
    originator:
    hostId: idssensorgraz01
    appName: cidwebserver
    appInstanceId: 11821
    time: 2004/10/18 07:28:23 2004/10/18 09:28:23
    errorMessage: name=errUnclassified srvcReq protoErr: unexpected_message [10,0]
    2. evError: eventId=1050261859615885103 severity=error
    originator:
    hostId: idssensorgraz01
    appName: cidwebserver
    appInstanceId: 1153
    time: 2004/10/18 07:28:23 2004/10/18 09:28:23
    errorMessage: name=errTransport WebSession::sessionTask(4) TLS connection exception: handshake incomplete.
    Maybe that helps?
    Markus

  • Configure vpn 3030 snmp for cisco works 2000

    vpn 3030 snmp error in cisco works 2000
    I want to monitor vpn3030 through vpn monitor,so do some config on vpn3030:
    1)Configuration | System | Management Protocols | SNMP
    enabled port 161
    2)Configuration | System | Management Protocols | SNMP Communities
    public
    3)Administration | Access Rights | Administrators | Modify Properties
    snmp modify config
    I can telent & http vpn3030,but when I run test in in cisco works 2000(server
    configuration|diagnostics|connectivity tools|management station to device)
    it said:
    Interface Status Test Results
    172.16.8.1 DOWN SNMPR failed
    sent: 5 recvd: 0 min: 0 max: 0 avg: 0 timeout: 2 size: 91 protocol: snmp_get port: 161
    SNMPW failed
    sent: 0 recvd: 0 min: 0 max: 0 avg: 0 timeout: 2 size: 0 protocol: snmp_set port: 161
    about my vpn3030
    Monitoring | System Status Thursday, 10 October 2002 16:40:16
    VPN Concentrator Type: 3030
    Bootcode Rev: Cisco Systems, Inc./VPN 3000 Concentrator Series Version 2.5.Rel Jun 21 2000
    18:57:52
    Software Rev: Cisco Systems, Inc./VPN 3000 Concentrator Series Version 3.0.2.Rel Apr 05 2001
    20:50:58
    Up For: 6d 0:04:27
    Up Since: 10/04/2002 16:35:49
    RAM Size: 128 MB
    There is only a 6509 between cisco works 2000 server and vpn3030,and no restrictions on tcp/ip
    flow.
    Please help me .thanks in advance.

    I test it in cw2000 cdone.
    This is really a strange question.
    the cw2000 server ip address is 10.8.1.122
    the vpn3030 's ip address is 172.16.8.1
    between them is a 6509, ip address is 10.8.1.201
    when I test connectivity between cw2000 server and 6509, everything is good,snmp is ok.
    when i test connectivity between cw2000 server and vpn3030, everything is good,except snmp is not response,while use third party snmp program,snmp status is ok!
    when I change the cw2000 server's ip address to 172.16.8.3 and connect it directly to vpn3030,test connectivity between cw2000 server and vpn3030 ,everything is good,snmp is ok.

Maybe you are looking for