Cisco Works upgrade

I'm currently running LMS3.2 and ordered an upgrade, Cisco sent me an electronic version of L-CWLMS-4.0-1.5KUP with a PAK in it but I was expecting a DVD version. I assume that I need to download/install an eval version and then enter the PAK to make it permanenet, please correct me if I'm wrong. I don't think I can upgrade over my existing LMS3.2, I beleive I will need to wipe out my existing LMS and start from the fresh.
Thank you all.

In addition to Michel's correct answer, I would add two things:
1. The current LMS version is 4.1, not 4.0. If you're going to the trouble to upgrade, it should be to the current version.
2. You can preserve your device list and other settings by backing up your LMS 3.2 and then restoring the data into the new LMS 4 installation. Follow the procedures here.
Whether or not you migrate your data, you should be reading and closely following the Installation Guide. LMS is very unforgiving of one not having all of the prequisites correctly established and procedure not followed.

Similar Messages

  • Attempting to upgrade Switch IOS with Cisco Works 2.06

    I am running RME version 4.05 and am trying to test pushing IOS images on a 3560 48port PS switch running 128mb ram and 16mb flash. When I run an analysis on Cisco works it states I only have 127mb of ram and 15 mb of flash. Is this a known bug in Cisco works. I am concerned if I upgrade with the current ram I have it will not work.

    Which report are you running specifically? I have seen something like this before.

  • Cisco Works LMS 4.0 doesn´t start

    Hello All
    i have big trouble with me LMS 4.0 installation. I did an Upgrade from LMS 3.2 to LMS 4.0. After that the Works was running without any problems. After some days i´d tried to login on the LMS and it told me something like my lincens where corrupt or so. I´d tried to start the CiscoWorks Demon Manger but he didn´t start. OK after some investigation at the i-net i decided to perform a clean installation of the Server an Cisco Works.
    So after i do thes i´d perform a restore of my old Data from LMS 3.2. Now i investicated that my ANI Server Falied to start. OK than i tried to restart the Works Demon ... f... and what will happend ?!?!?! The demon doesn´t start. Can someone help me ?!?! Please i will not perform a new istallation again.
    C:\Windows\system32>net start crmdmgtd
    The CiscoWorks Daemon Manager service is starting.
    The CiscoWorks Daemon Manager service could not be started.
    The service did not report an error.
    More help is available by typing NET HELPMSG 3534.
    Thanks
    Mario
    Hi i have an update for this issues ... After i´d tried to start all Works- Services be hand ... all Services will start execpt the deamon ... When i loged in i get messages "License Server/Deamon Manager is down. Please  check license.log for more information."
    Thats the same situtaion befor the new installation.

    Hi Afroj
    i´d just have an update for you and maybe for Martin. I´d checked the services and investigate that the ANIDatabase Engine
    was not stoped. After i stoped the service "by Hand". I tried to reinalize the Database and see ... IT WORKS ...
    D:\CiscoWorks\CSCOpx\bin>perl.exe dbRestoreOrig.pl dsn=ani dmprefix=ANI
    WARNING: Existing contents of ani database will be lost.
    Do you want to continue [y/n]?y
    INFO: Starting the DataBase
        Starting database engine aniEng
    INFO: Process created
    INFO: Started the Database engine : aniEng Retry 0
    INFO: Started the Database engine : aniEng Retry 1
    INFO: Started the Database engine : aniEng Retry 2
    INFO: Started the Database engine : aniEng Retry 3
    INFO: Started the Database engine : aniEng Retry 4
    INFO: Started the Database engine : aniEng Retry 5
    INFO: Started the Database engine : aniEng Retry 6
    INFO: Started the Database engine : aniEng Retry 7
    INFO: Started the Database engine : aniEng Retry 8
    INFO: Started the Database engine : aniEng Retry 9
    INFO: Getting message
    INFO: Connect the database dsn=ani
    INFO: Connected the Database
    INFO: Command Executed
    INFO: Connecting the Database ani
    INFO: Company=Cisco Systems;Application=NMTG;Signature=010fa55157edb8e14d818eb4f
    e3db41447146f1571g32125eb777a87cbf8b29a954f559d4221b792ff8
    INFO: Preparing AUTH cmd
    INFO: AUTH Executed
    INFO: AUTH cmd finished
    INFO: Stopping the Database engine ani
        Stopping database engine aniEng
    INFO: File not exists.SQL Anywhere Command File Hiding Utility Version 10.0.1.40
    51
    INFO: Database [ani] authenticated successfully.
    ani database initialization is completed.
    D:\CiscoWorks\CSCOpx\bin>
    D:\CiscoWorks\CSCOpx\bin>pdshow ANIServer
            Process= ANIServer
            State  = Running with busy flag set
            Pid    = 11136
            RC     = 0
            Signo  = 0
            Start  = 8/22/2011 1:01:29 PM
            Stop   = Not applicable
            Core   = Not applicable
            Info   = ANIServer started.
    Many Thanks for your help ...
    Regards
    Mario

  • Error Message in Cisco Works

    I am running device troubleshooting in cisco works on a 1200 series acces point.
    I am getting the followinf error message:
    VTP Disconnected Domain DomainName:NO_VTP
    Do I need to upgrade IOS on all AP's??

    It seems like that Link in a VTP domain is not set to trunk. Verify the trunk.

  • Cisco works LMS 4.0 ,Apache HTTP Server CVE-2011-3192 Denial Of Service Vulnerability

    Cisco works LMS 4.0 ,Apache HTTP Server CVE-2011-3192 Denial Of Service Vulnerability
    This vulnerability has been fixed in release apache 2.2.20 and further corrected
    in 2.2.21. You are advised to upgrade to version 2.2.21 (or newer) or the
    legacy 2.0.65 release,
    Can any one give the steps to upgrade the apache http server 2.2.10 to 2.2.21 in windows 2008 server?

    For the following PSIRT:
    http://www.cisco.com/en/US/products/csa/cisco-sa-20110830-apache.html
    Download the following patch "lms40-win-Oct2011-su1-0.zip" :
    http://www.cisco.com/cisco/software/release.html?mdfid=283434800&flowid=19062&softwareid=280775103&os=Windows&release=4.0&relind=AVAILABLE&rellifecycle=&reltype=latest
    The instructions should be in the zip file how to install the patch.
    This should cover all theses bugs that you can query in the bug tool kit:
    http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs
    CSCte45565
    CSCto12712
    CSCto23584
    CSCto23622
    CSCto35544
    CSCto35577
    CSCtq48990

  • Cisco Works LMS HUM issue

    Hi,
    I am using Cisco works LMS 3.1 with HUM 1.1.0. I am receiving thresold and job schedule mail alert from HUM.
    It is showing error in JOB history  “Not able to connect the mail server” while alerts from RME,IPM,CS,DFM are coming on mail.
    I have Configured HUM just 3 days back and all others application had been configure 4 months back.
    Please help.
    Regards,
    DJ

    Hi Clarke,
    Thanks for response. Please see the attached HUM smtp error. I have tried the HUM JOB with sniffer to filter smtp port 25 traffic but nothing is reflecting
    in sniffer when trying to send mail through HUM while DFM,RME IPM mail are showing in sniffer and we are getting mail as well.
    I have upgraded HUM version from 1.1.0 to 1.1.2 but the error is same.
    Regards,
    Dinesh Joshi

  • Cisco Works server install

    All,
    does anyone know the best practise install in respect to partitions, O/S, and what locations the log files should be placed? We recently upgraded from an old Cisco Works platform and now our full CW is broke
    So can anyone recommend any best practise scenarios?
    We have 4 x 146 gb disks that we could utilise.
    Thanks in advance,
    Tam.

    Is your environment Windows or Solaris? Did you upgrade your hardware platform only or also change from an earlier LMS version to the lastest (4.0)?
    Generally speaking, the installation guide has a good number of details. If you follow it carefully, your should have a successful installation. As with many products, when upgrading it is usually most successful to back up the data on the old system and do a clean install on the new, restoring the data after verifying a basic working system.

  • Cisco Works does note recognise 7204VXR NPE-G2 variant IOS

    I am trying to load a 7200 NPE-G2 variant IOS into our Cisco Works software repository in order to then upload it to a 7204VXR.  When browsing to the folder containing the IOS and then attempting load, Ciso Works does not recognise the NPE-G2 variants (with file names starting c7200p), however it does recognise vanilla c7200 variants.
    We  are running with LMS 2.6, RME 4.0.5, DFM 2.0.6
    Do we need to upgrade?

    You will need to update your RME device packages to the latest versions.  Go to Common Services > Software Center > Device Update, and check the boxes next to RME and Common Services.  Download and install all available packages, then you should be able to add the c7200p image to the repository.

  • How to install Cisco Work 3.2 on Windows 2008 Server Standard R2

    Hi Everyone,
    I have got Cisco Works LAN Management 3.2. But the problem is that i have a Windows 2008 Server Standard R2 and when i try to install, it fails. What I read from the below link is that it supports
    "Windows 2008 Server Standard and Enterprise Edition with Service Pack 1 and 2. Both 32-bit and 64-bit operating systems are supported on the above versions."
    http://www.cisco.com/en/US/partner/prod/collateral/netmgtsw/ps6504/ps6528/ps2425/data_sheet_c78-534877.html
    Please help me out on how i should install on the Windows 2008 Server Standard R2. If there is any patch or any other way out.
    Awaiting your response.
    Farid

    Hi ,
    LMS 3.2 is not supported on Windows 2008 Server Standard R2.
    here is the supported platoform for LMS 3.2
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/install/guide1/prereq.html#wp1110367
    Thanks,
    Gaganjeet

  • Cisco Works - need to re-use a 3560, how to delete and re-add in Cisco Works

    Hello.  I did not see a cisco works section on the forum, forgive me if it's there and I missed it.  I have removed a 3560 switch from one location and am going to rename it (same IP though) and deply it in a different department.  We have cisco works sending critical and informational alerts as well as backup the configs on Sunday mornings.  I think I was able to get it to stop sending alerts when I unplugged and unhooked the switch.  I want to give the switch a new host name and re-deploy it.  I assume it will be easier to delete and then re-add the switch to cisco works.  Is the a document where I can follow steps to remove it from cisco works?  I have the documentation, but it is hard to read and they don't really have an area that specifically says "remove a switch from cisco works", and I don't want to break everything for the other 55 switches that cisco works does do the alerts and backups for.  I know cisco works is full of different modules, so I was wondering if there was a document or some type of help I could get for doing this.  Any help would be greatly appreciated.  Thanks.  Mike Baker

    Hi,
    It sounds like a tutorial may be what you are looking for. Here is one based on LMS 3.1.
    https://learningnetwork.cisco.com/docs/DOC-4031
    To remove a device from DCR (Device & Credential Repository) navigate to Common Services > Device and Credentials > Device Management.
    Thanks,
    Nick

  • Cisco Works Integration with MARS

    Can cisco works be integrated with MARS. I mean cisco works is acting as a syslog server for some switches. Can mars pull the records from Cisco Works and use it for its co-relation

    As Michael pointed out, configuring two syslog destinations on your switch is possible, and allows the switch to send to both CiscoWorks and CS-MARS simultaneously.  This affords the safety that should one system be down, the other system will continue to receive syslog events from the switches.  Should you not wish to configure two logging destinations on your switch, you could configure your switches to send their syslogs to CS-MARS and configure CS-MARS to relay the received syslog messages to CiscoWorks.  This options is outlined in the CS-MARS user guide:
    http://www.cisco.com/en/US/docs/security/security_management/cs-mars/6.0/user/guide/combo/cfgOver.html#wpmkr181270
    Scott

  • Cisco Work (LMS 2.6) Device Configuration

    Hi,
    Can anyone tell me where is the default location of device configuration ( Running conf ) saved in Cisco Work (LMS 2.6) Server.
    Thanks & Regds,
    Lalit

    if you enable the so called shadow directory feature under:  Admin -> Config Mgmt -> Archive Mgmt -> Archive Settings
    then the defaut location is \CSCOpx\files\rme\dcma
    Cheers,
    Michel

  • Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

    Hi All,
    Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
    Any help would be greatly appreciated.
    Thanks in advance.
    Samir

    Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices.  RME will only use HTTPS to fetch VPN concentrator configurations.

  • Cisco works LMS 3.0.1 does not archiever configuration for cisco 7201 router

    Hi All,
    We have Cisco works LMS 3.0.1 and it does not archiever configuration for cisco 7201 router.
    Any help would be appriciated.
    Thanks in advance
    Samir

    Hi,
    *** Device Details for d0151-100 ***
    Protocol ==> Unknown / Not Applicable
    Selected Protocols with order ==> TFTP,SSH,HTTPS
    Execution Result:
    Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
    This is the error while doing syn archieve.
    I am not sure about Rtr7000 version but we have latest Rtr7000.
    Waiting for your kind reply.
    Samir

  • Cisco Wireless LAN Controller 4402 under Cisco Works RME 4.0?

    I am trying to manage a Cisco 4402 using non-default snmp communities from Cisco Works RME 4.0.  RME Credential Verification fails with “Device Not Supported” recorded against selected option; however, the controller does respond to snmp queries.  The 4402 has snmpv1 through snmpv3 enabled; and the snmp communities are associated with the correct client IP.  Is the WLC only responsive to snmp from the WLS and should the box be manageable via it’s management interface.  ICMP and telnet to the WLC from RME works OK.
    Advice and Guidance would be greatly appreciated.

    What firmware version are on the WLC's..... minimum is 5.0.148 per the RME Table.
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_resource_manager_essentials/4.0.5/device_support/table/RME405.html

Maybe you are looking for