CiscoView 5.3 and Catalyst 4506 issues.

Hi,
I cannot display on CiscoView 5.3 the Cat4506 device.
So, when i m trying to access to this equipement by IP address, i've got a warning message "Device package not installed"
I was checking in the device package installed in my CiscoWorks 6.1 and i found that it is already installed.
Any comments ??
Can you tell me which device package i need to display this device on CiscoView 5.3
Thanks for your response.

I have the same message with this package Cat4000IOS-14.0 , it seems that one should be updated;
But if the version 50 has the same message, it seems to be something else.

Similar Messages

  • Catalyst 4506 and Modules in Pwr Over state

    Hello,
    First of all, my excuses for my bad english.
    I am experiencing a problem with a Cisco Catalyst 4506.
    The switch is filled with 48 port PoE blades (WS-X4248-RJ45V).
    The error we receive is:
    Sept 5 15:40:12: %C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Inline power exceeds threshold: Module status changed to 'Pwr Over'
    Sept 5 16:37:04: %C4K_IOSMODPORTMAN-6-INLINEPOWEROK: Inline power within limits: Module status changed to 'Ok'
    Sept 5 16:37:04: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 6 (WS-X4248-RJ45V S/N: JAB080609GN Hw: 2.0) is online
    According to the Cisco website:
    Explanation
    This message indicates that the measured PoE is at least 50 w higher than the configured value. The switch has either misconfigured PoE or an unauthorized powered device that is connected to the switch and is drawing a lot of PoE.
    Out put for the commands sh power details and sh module all are attached.
    The switch has no PoE devices on the specific blade.
    Atleast not that we know.
    Does any one know some other solution?
    Thanks in advance.
    Martijn Groenleer

    Well, blade six went offline on the first row of the log i posted earlier.
    The problem is, the log doesn't mention in the message which module went offline.
    About the 'efficiency' i noticed this also, what could be causing this? Power supplies are already replaced. PoE is on default settings currently.
    A full log related to these power over warnings:
    Aug 30 23:27:00: %C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Inline power exceeds threshold: Module status changed to 'Pwr Over'
    Aug 30 23:39:34: %C4K_IOSMODPORTMAN-6-INLINEPOWEROK: Inline power within limits: Module status changed to 'Ok'
    Aug 30 23:39:34: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 6 (WS-X4248-RJ45V S/N: JAB080609GN Hw: 2.0) is online
    Sep 3 08:45:46: %C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Inline power exceeds threshold: Module status changed to 'Pwr Over'
    Sep 3 08:57:49: %C4K_IOSMODPORTMAN-6-INLINEPOWEROK: Inline power within limits: Module status changed to 'Ok'
    Sep 3 08:57:49: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 6 (WS-X4248-RJ45V S/N: JAB080609GN Hw: 2.0) is online
    Sep 4 01:53:04: %C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Inline power exceeds threshold: Module status changed to 'Pwr Over'
    Sep 4 02:23:16: %C4K_IOSMODPORTMAN-6-INLINEPOWEROK: Inline power within limits: Module status changed to 'Ok'
    Sep 4 02:23:16: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 6 (WS-X4248-RJ45V S/N: JAB080609GN Hw: 2.0) is online
    Sep 4 16:10:58: %C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Inline power exceeds threshold: Module status changed to 'Pwr Over'
    Sep 4 17:20:23: %C4K_IOSMODPORTMAN-6-INLINEPOWEROK: Inline power within limits: Module status changed to 'Ok'
    Sep 4 17:20:23: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 6 (WS-X4248-RJ45V S/N: JAB080609GN Hw: 2.0) is online
    Sep 4 17:58:14: %C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Inline power exceeds threshold: Module status changed to 'Pwr Over'
    Sep 4 18:09:37: %C4K_IOSMODPORTMAN-6-INLINEPOWEROK: Inline power within limits: Module status changed to 'Ok'
    Sep 4 18:09:37: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 6 (WS-X4248-RJ45V S/N: JAB080609GN Hw: 2.0) is online
    Sep 4 19:13:15: %C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Inline power exceeds threshold: Module status changed to 'Pwr Over'
    Sep 4 19:56:11: %C4K_IOSMODPORTMAN-6-INLINEPOWEROK: Inline power within limits: Module status changed to 'Ok'
    Sep 4 19:56:11: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 6 (WS-X4248-RJ45V S/N: JAB080609GN Hw: 2.0) is online
    Sep 5 09:02:16: %C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Inline power exceeds threshold: Module status changed to 'Pwr Over'
    Sep 5 09:10:46: %C4K_IOSMODPORTMAN-6-INLINEPOWEROK: Inline power within limits: Module status changed to 'Ok'
    Sep 5 09:10:46: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 6 (WS-X4248-RJ45V S/N: JAB080609GN Hw: 2.0) is online
    Sep 5 15:40:12: %C4K_IOSMODPORTMAN-4-INLINEPOWEROVERWARNING: Inline power exceeds threshold: Module status changed to 'Pwr Over'
    Sep 5 16:37:04: %C4K_IOSMODPORTMAN-6-INLINEPOWEROK: Inline power within limits: Module status changed to 'Ok'
    Sep 5 16:37:04: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 6 (WS-X4248-RJ45V S/N: JAB080609GN Hw: 2.0) is online

  • LMS 3.2 and Catalyst 4500 WS-X4648-RJ45-E module card

    Hi all,
    I have a rpoblem with a specific client with LMS 3.2. We are using LMS 3.2 on Windows 2008 and everything seem to be working OK. The issue is in the CiscoView with the 4500 switches. CiscoView can see the supervisors on all 4500 switches (6); but cannot see the switchcards when the switchcards are WS-X4648-RJ45-E. Find the sh inv output below:
    CSR-D1#sh inventory
    NAME: "Switch System", DESCR: "Cisco Systems, Inc. WS-C4507R-E 7 slot switch "
    PID: WS-C4507R-E       , VID: V01, SN: FOX1152GKR1
    NAME: "Clock Module", DESCR: "Clock Module"
    PID: WS-X4K-CLOCK-E    , VID: V01, SN: JAE120354DD
    NAME: "Linecard(slot 1)", DESCR: "10/100/1000BaseT (RJ45) with 48 10/100/1000 baseT "
    PID: WS-X4648-RJ45-E   , VID: V01, SN: JAE14410NLT
    NAME: "Linecard(slot 2)", DESCR: "6 Dual media SFP or 10/100/1000BaseT (RJ45)V voice power ports (Cisco/IEEE)"
    PID: WS-X4506-GB-T     , VID: V05, SN: JAE120351NC
    NAME: "Linecard(slot 3)", DESCR: "Supervisor 6-E 10GE (X2), 1000BaseX (SFP) with 2 10GE X2 ports"
    PID: WS-X45-SUP6-E     , VID: V01, SN: JAE120576HG
    NAME: "TenGigabitEthernet3/1", DESCR: "10Gbase-LRM"
    PID: FTLX1341E2-C1     , VID: A  , SN: FNS1352175M
    NAME: "TwinGig Converter 3/2", DESCR: "TwinGig Converter Module"
    PID: 800-27645-01      , VID: A0 , SN: CAT1147H2WK
    NAME: "Linecard(slot 4)", DESCR: "Supervisor 6-E 10GE (X2), 1000BaseX (SFP) with 2 10GE X2 ports"
    PID: WS-X45-SUP6-E     , VID: V07, SN: JAE14080NL2
    NAME: "TwinGig Converter 4/2", DESCR: "TwinGig Converter Module"
    PID: 800-27645-01      , VID: A0 , SN: CAT1147H2BV
    NAME: "Linecard(slot 7)", DESCR: "10/100/1000BaseT (RJ45) with 48 10/100/1000 baseT "
    PID: WS-X4648-RJ45-E   , VID: V01, SN: JAE14420A2F
    I have updated the s/w to 12.2(53) SG1 with no luck.
    Any ideas?

    Hi Nicos,
    I have exactly the same issue with LMS 3.2 CiscoView under Windows 2003 and catalyst switch 4506-E.
    4506-E are in IOS 12.2(53)SG2.
    I installed latest 4500IOS V 19.0 ciscoview device package without success.
    Did you fix your problem ?

  • Monitoring Cisco Catalyst 4506

    Hello
    I am looking Cisco SNMP MIB or some Nagios plugin that allow to monitoring PoE status on Cisco Catalyst 4506 modules and check Led indicator status  simmilar I can do it by coomand "show enviroment "
    Module 2 Status Led Color : Green    PoE Led Color: Orange
    Module 3 Status Led Color : Green    PoE Led Color : Green
    Thank you very much

    Hi jon.marshall,
    Thanks for you reply. I'll explain how the traffic flows:
    1. Client boot up workstation
    2. After booting up, client obtain IP addressing through DHCP service from a remote DHCP server using gateway of VLAN210 (172.18.212.1)
    3. IP addressing issued to client (for e.g 172.18.212.128) and open web browser (HTTP) using a proxy (proxy.skynet.gov) with a DNS setting of skynet.gov.
    4. Next hop is a Juniper Enforcer (a.k.a firewall) with IP address 172.18.221.234 (Enforcer 1 - Master) and 172.18.221.235 (Enforcer 2 - Backup) which have a policy rule stating that the client range of 172.18.212.0 to 172.18.212.255 wanting to contact the proxy (proxy.skynet.gov), the next hop would be the Juniper UAC Host checker (with IP address of 172.18.223.254).
    Note: There are 2x physical Junpier Enforcer and only 1x Juniper Host Checker
    5. Juniper UAC Host Checker checks client workstation to ensure that minimum requirements are met before allowing client to go to internet
    6. Once clients pass the Juniper UAC Host Checker, traffic to the internet is then allowed.
    7. Clients surf the internet.
    8. End
    To answer your questions:
    i. The UAC is not on the same subnet however, all routing is done on the Cisco Catalyst 4506 and the UAC and VLAN are all on the 4506 too.
    ii. I'm not sure if the Juniper UAC is the one that makes all Http request of VLAN210 (172.18.212.0 to 172.18.212.255) or it will let the client make its on Http request after it passes the host checker.
    iii. Yes. I have 2x Cisco Catalyst 4506 and they are connected to each other through HSRP
    iv. The proxy (proxy.skynet.gov) is configured on the clients browser.
    Note: Is the DNS name of the proxy server, NOT the IP address of the proxy server.
    I hope the above provided information is sufficient for you reference to provide me the actual syntax for my requirement. Thanks.
    Cheers!!!

  • No GLX on latest kernel, X, and catalyst

    local/catalyst 11.7-1
    local/catalyst-utils 11.6-1
    local/lib32-catalyst-utils 11.6-1 (lib32)
    local/xorg-server 1.10.3.901-1 (xorg)
    local/linux 3.0.1-1 (base)
    01:00.0 VGA compatible controller: ATI Technologies Inc RV770 [Radeon HD 4870]
    [max@gayforcetwo Steam]$ glxinfo
    name of display: :0.0
    X Error of failed request: BadRequest (invalid request code or no such operation)
    Major opcode of failed request: 136 (GLX)
    Minor opcode of failed request: 19 (X_GLXQueryServerString)
    Serial number of failed request: 18
    Current serial number in output stream: 18
    [max@gayforcetwo Steam]$ fglrxinfo
    X Error of failed request: BadRequest (invalid request code or no such operation)
    Major opcode of failed request: 136 (GLX)
    Minor opcode of failed request: 19 (X_GLXQueryServerString)
    Serial number of failed request: 18
    Current serial number in output stream: 18
    Section "ServerLayout"
    Identifier "aticonfig Layout"
    Screen 0 "aticonfig-Screen[0]-0" 0 0
    EndSection
    Section "Module"
    EndSection
    Section "Monitor"
    Identifier "aticonfig-Monitor[0]-0"
    Option "VendorName" "ATI Proprietary Driver"
    Option "ModelName" "Generic Autodetecting Monitor"
    Option "DPMS" "true"
    EndSection
    Section "Device"
    Identifier "aticonfig-Device[0]-0"
    Driver "fglrx"
    BusID "PCI:1:0:0"
    EndSection
    Section "Screen"
    Identifier "aticonfig-Screen[0]-0"
    Device "aticonfig-Device[0]-0"
    Monitor "aticonfig-Monitor[0]-0"
    DefaultDepth 24
    SubSection "Display"
    Viewport 0 0
    Depth 24
    EndSubSection
    EndSection
    What's going on?
    Last edited by synthead (2011-08-11 17:53:31)

    I don't know how you updated, but I use the catalyst repository, and in the last big update, there was an issue in the order of installing linux 3 and catalyst 11.7 (?), such that the fglrx hook failed. I had to redo building the image, whereupon the hook worked. Did you check for messages as it rebuilt the image?
    Sorry if this was obvious, but I am not arch-guts/catalyst savvy.
    HTH

  • Dacl on ACS 5.1 and Catalyst switch 3560

    Dear all
    I have ACS 5.1 and Catalyst switch 3560 with version 12.2(53)SE. I configure a dacl on the ACS and I use it on authorization profile.
    This authrization profile is used on access policy.
    I tried the authentication but it doesn't work. I checked the ACS logs and I found that the user is authenicated successfuly but the dacl gives this error (The Access-Request for the requested dACL is missing a cisco-av-pair attribute with the value aaa:event=acl-download. The request is rejected)
    Steps:
    11001  Received RADIUS Access-Request
    11017  RADIUS created a new session
    11025  The Access-Request for the requested dACL is missing a cisco-av-pair attribute with the value aaa:event=acl-download. The request is rejected
    11003  Returned RADIUS Access-Reject
    DACL:
    deny ip host 1.2.3.4 1.2.3.0 0.0.0.255 log
    permit ip any any log
    Thanks on advance,

    Dear Tiago
    I applied the command "radius-server vsa send". Now I can see the dacl is applied but I can't see it on the switch and even the authentication is succueeded ont the ACS logs but it give me unauthoized on the switchport. You can see the logs( started with the username acstest and the access-list is applied but it doesn't work and you can see theat it goes for mab after eap timed out). I hope you can help on this issue.
    Dec 13,10 10:29:00.513 AM
    00-23-AE-7A-58-A6
    00-23-AE-7A-58-A6
    Default Network Access
    Lookup
    Dot1x-3560-Switch
    1.2.3.4
    FastEthernet0/5
    TESTACS
    22056 Subject not found in the applicable identity store(s).
    Dec 13,10 10:28:29.186 AM
    #ACSACL#-IP-Guest-4cfcc14d
    Dot1x-3560-Switch
    1.2.3.4
    TESTACS
    Dec 13,10 10:28:28.726 AM
    acstest
    00-23-AE-7A-58-A6
    Default Network Access
    PEAP (EAP-MSCHAPv2)
    Dot1x-3560-Switch
    1.2.3.4
    FastEthernet0/5
    TESTACS
    Thanks,

  • Trying to interconnect Catalyst 4506 (IOS) & Catalyst 6509 (CatOS) using FS

    Hey all,
    I'm currently having a problem interconnecting a Catalyst 4506 using IOS and a Catalyst 6509 using CatOS via FSO. The FSO is all setup and they show that they are talking but when we plug the fiber optic cables into the switches, we get a notconnect status on the switches. The link lights on both switches don't light up either. I have configured both sides as follows
    6509 (the Gigabit Port is 2/6):
    set port negotiation 2/6 disable
    set trunk 2/6 nonegotiate dot1q 1-1005,1025-4094
    4506 (the Gigabit Port is 1/1):
    interface GigabitEthernet 1/1
    switchport trunk encapsulation dot1q
    switchport mode trunk
    switchport nonegotiate
    speed nonegotiate
    We were told by the FSO company that both ends must turn off negotiation in order for it to work. On the end with the Catalyst 6509, I have tried plugging another known working fiber optic line into the 2/6 port and the link light lights up so we know that the port isn't broken. Any ideas? I am lost.
    Background:
    We currently have a T1 line that serves as a point to point between the two buildings. We were trying to get rid of it and go with Free Space Optics (FSO) to increase bandwidth between the two buildings. We have 5 VLANs on each side (on the 4506 side, Vlans 110, 120, 132, 140, & 104 and on the 6509 side, Vlan 10, 20, 32, 40, 4) and the point to point is on the 200 network to interconnect the switches.

    Hie David,
    Just to start with are we sure that Rx of one switch terminates on Tx of other and vice versa. The fiber cable which is plugged in the trnasmitter of one switch must go to the receiver of another switch. You can just try swapping the TX and RX points at one switch.
    I doubt this because as you have said even the link light is not coming up.

  • Wccp catalyst 4506

    Hi..
    I have been trying to configure wccp on catalyst 4506 switches running VSS but unable to complete setup config. I need your help in configuring wccp.
    i want ports www/https to be redirected to proxy server. And want to enable wccp on vlan interface. Pls help me in configuring it. Also any config example will be really helpful and appreciated.

    Your switch is crashing due to multibit ECC errors. Upgrade your ROMMON to 12.1(20r)EW2. You might want to also upgrade IOS to 12.2(18)EW4
    http://www.cisco.com/cgi-bin/bugtool/onebug.pl?bugid=CSCed25996
    You can download it from
    http://www.cisco.com/kobayashi/sw-center/lan/cat4000.shtml

  • Do Cisco router 2811 and Catalyst 3750 support SNMPv3?

    Hi,
    Do Cisco router 2811, IOS 12.4(20)Ti, and Catalyst 3750, IOS 12.2.(53)SE, support SNMPv3?
    Attached file contains my SNMPv3 configurations and "show snmp" results.  Would you please give me your advice?  Thanks.
    Hugh

    Hugh
    Certainly both the 2811 and the 3750 do support SNMPv3. So support for the feature is not an issue in your situation.
    I have looked at the config that you attached and believe that it looks reasonable. You have not told us about the SNMP server that will communicate with these devices. So we have no way to know if the details of the configuration are correct.
    Have you attempted to discover these devices with an SNMP server that is configured to use SNMPv3 and has this user and passwords configured? If it does not work my first suggestion would be to check to verify that the passwords configured are exactly the same on the clients and on the server (and perhaps re-configure the passwords just to be sure). If the passwords are not a problem my second suggestion would be to check and verify that the authentication and encryption parameters match between the server and the clients.
    HTH
    Rick

  • [solved] lib32-mesa-libgl and catalyst-total are in conflict

    Steam now depends on lib32-mesa-libgl which is in conflict with catalyst-total.
    lib32-mesa-libgl and catalyst-total are in conflict (lib32-libgl)
    I'm not sure where to go from here.
    EDIT:
    catalyst-total was updated 5 minutes after I made this post. The issue has been resolved.
    Last edited by beardedlinuxgeek (2013-02-26 19:32:00)

    I have the same problem, please help

  • My website and catalyst admin is down!!!!! Please help

    My website and catalyst admin has been down for the last two hours. I have contacted you by ticket and email with no reply.
    This time of year is very busy for us and our customers canot access our online sales through links on our website.
    Please help and advise on issues.

    Hi,
    Nothing has been changed easy space end….
    I looked on your link
    Only Domains - Global Domain Name Registrar
    and they seem to be pointing to the correct location?
    Domain Name: SPENCERBROWNPHOTOGRAPHY.COM
    Registrar: EASYSPACE LTD.
    Whois Server: whois.easyspace.com
    Referral URL: http://www.easyspace.com
    Name Server: ns1.worldsecuresystems.com
    Name Server: ns2.worldsecuresystems.com
    Name Server: ns3.worldsecuresystems.com
    Status: clientHold
    Status: clientTransferProhibited
    Status: clientUpdateProhibited
    Updated Date: 27-sep-2014
    Creation Date: 11-jan-2007
    Expiration Date: 11-jan-2015
         PLUS I CAN NOT LOGIN TO THE BUSINESS CATALYST AFDMIN AREA FOR THIS SITE? - SO IT LOOKS LIKE THIS IS A PROBLEM YOUR END.
    Please please help as i am getting customers calling me as they can’t order there school photos.
    Many thanks
    Spencer Brown
    Director
    E: [email protected]
    W: www.spencerbrownphotography.co.uk
    T:  01359 240351
    M: 07940 749761
    LIKE US on Facebook
    Office/Studio: 1st Floor, The Co-operative, The Street, Woolpit, Bury St Edmunds, IP30 9SA
    Studio Terms & Conditions
    This e-mail is private and confidential and is for the addressee only.
    You are strictly prohibited from copying, disclosing, using, printing, or distributing it or any information contained in it. All images contained in this email are the copyright of Spencer Brown Photography. Any attachment received in the e-mail should be virus checked by the recipient before being opened. Spencer Brown Photography does not accept liability (for negligence or otherwise) for passing on viruses in e-mails.

  • Gmail/Exchange email and calendar syncing issues

    I have wiped my email accounts several times and entered in my data in the various ways as shown through the forums but my email accounts do no sync properly whether it is manual or active synced.
    I read my emails in my gmail and my Microsoft exchange account and will delete or file them away but then when I check my accounts on my desktop, they are not synced as I've done so on my phone. I've also noticed that my calendars are not synced correctly either.
    Could someone help me understand why and how these issues can be fixed? I'm in meetings for most of the day so I rely on my phone to keep me mobile. Was this a bad purchase?!?!

    Hi JadeyMU,
    How do you have your Microsoft Exchange account configured on your BlackBerry Z10? Are you using ActiveSync, BlackBerry Enterprise Server (BES), IMAP or POP?
    Thanks.
    -CptS
    Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
    Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

  • My experience with Apple TV and HDMI/HDCP issues

    I am convinced that it is the software update to 4.2.2 from 4.2.1 that is causing this issue.  All forms of applications only worked once for me and then it reverted back to HDCP issues.  I read several postings everywhere including plenty at Apple's forum and AVS where people were very frustrated with this HDCP issues.  Anyways, here is what I did before taking it back to Apple store....I bought AUVIO high speed cables from Radio Shack which is rated very high and tried that and I still got HDCP issues when using NetFlix or AirPlay from iPad.  Youtube from Apple TV always worked well without HDCP complaints.
    I packed everything back and took it to Apple Store (you can return without re-stocking fee up to 14 days from the day of purchase).  After 14 days, you cannot even return it and you can ONLY fix it.  I waited for a Technician.  They heard my complaints but didn't refute any of it (possibly because they have had numerous complaints on this product).  It took 5 minutes inside for them to test and see similar issues with the box that I had.  So, they have swapped it for a new box.  Before I left the store, I checked the settings including software version and Audio/Video settings in the Apple TV that is connected at the store.  I found three main differences none of which the Apple customer service staff agreed could be the reason for my problems (surprise!!)
    1.  The software update from the shelf and the one they were using was NOT updated to 4.2.2 (it was still running 4.2.1)
    2.  Because of the software update, the Audio/Video setting for HDMI had the options to toggle between Auto, RGBy, RGBhi & RGBlo bandwidth.  I believe this was in place to make the HDMI interface output as component with higher or lower bandwidth but the newer update will ONLY give you the Auto option (!!!)
    3.  They had this directly Ethernet wired and not through Wireless network and were recieving the all the full bar strength signals.  On the box that I returned, eventhough I have 18 Mbps speed at the house (any given time of the day), the Network speed test was taking a long time.  Moreover, after the Apple TV network test, it doesn't spit out the outcome of the tests (a BIG bummer and useless for testing).
    Anyways, I took the new box and hooked it up directly to my SONY BRAVIA XBR3 TV to one of the HDMI ports, disabled the feature to send or recieve data to Apple directly and did NOT update the software.  It worked fine and have tested all of the options.  From what I have read so far (I have only spent 30 hours of my weekend on this when Apple product hookups are supposed to take 5 minutes ONLY), there is NO guarantee that it will work continuously as people have had things work on them for 6 months and then suddenly have the HDCP issues.
    Will wait to see....if it continues to work....

    I figured it out. Had to go to general settings on the main screen and restart. Synch of audio is much better.

  • I have a serious (and bizarre!) issue with my novation impulse (Although i've tried it with two other keyboards and i still have the same problem) and its compatibility with mainstage 3

    i have a serious (and bizarre!) issue with my novation impulse (Although i've tried it with two other keyboards and i still have the same problem) and its compatibility with mainstage 3.
    the problem is best explained on the following one - page thread: 
    https://discussions.apple.com/thread/3951518?start=0&tstart=0
    (Clearly i'm not alone in this problem, although i think i figured out what's going wrong a little more than he did...read on!)
    his solution, to put mainstage in jump mode, is very unsatisfactory to me, as it bounces all of a sudden to drastically different settings.
    basically, my analysis is that my controller is NOT receiving MIDI date from mainstage.  in other words, mainstage knows what my controller is doing, but my controller doens't know what mainstage is doing.
     let's say i turn the knob all the way to the right ... 127...and the virtual fader goes to the right like it's supposed to. 
    now...next...let's say i change to a different patch, where that same VIRTUAL fader is not at the max clockwise position..maybe it's only at 1pm.  now when i turn the physical knob to the RIGHT, the midi data is still at 127 on the controller!  it didn't "reset" to sync up with the new level (say 80 or so) setting on the new patch.  so i can't increase that new setting of 80 by continuing to turn the knob to the right.  i have to turn it all the way to zero,...and then continue PAST zero until the controller thinks that IT is at 0...at that point the controller and mainstage are in agreement, and things work fine....so bascially, the keyboard thinks the level is at max...but mainstage thinks the level is at 1pm.
    i am using Logic 9, and i have a macbook pro 2.9 Ghz I7 with 8 gigs of memory and OS X 10.8.4

    Hi Josh,
    Thanks for taking the time to contact us here a Novation for technical support. Lets continue to correspond via email so we can get your issue resolved.
    Thanks.
    Mike Towns

  • Interesting and an  imporatant issue at sales order schedule line.

    hi all,
    interesting and an  imporatant issue at sales order schedule line.
    i created a sales order with 10 qty.and the system proposed a two schedule lines.
    let's say to order created date is 27.11.2008.and the requested delivery date is 27.11.2008.
    but the stock is not available today then the system proposed two more schedule lines apart from the 27.11.2008.so now there are three schedule lines like below.
    schedule line date                      Material availabilyt date   delivery date                   
    27.10.2008 with zero quantity.     
    28.10.2008 with 5 qty.                28.10.2008                     29.10.2008
    02.10.2008 with 5 qty.                02.10.2008                     03.10.2008
    now the delivery and pgi already for the schedule line 28.10.2008.
    then when i run the availability check on 01.11.2008 system is over writing the material vailability date as today at the scheduleline number two.
    now i can able to view only two schedule lines only.
    schedule line date                      Material availabilyt date   delivery date                   
    28.10.2008 with 5 qty.                01.11.2008                     29.10.2008
    02.10.2008 with 5 qty.                01.11.2008                     02.11.2008
    now my concern when we reschedule the avalability check it should notchange the Material availability date of the schedule line which i already delivered.
    Regards,
    sheshukumar

    can any one repsond for this.....

Maybe you are looking for