Ciscoworks - devices "not configured in ACS"
Hi all,
Can anyone explain why Ciscoworks places some new devices in the above category even when the device config, ACS, etc is all configured correctly? I have a handful of devices that keep going into this category and there is nothing I can do to stop it happening - it is a real hassle as you have to then set CW to non ACS mode restart the daemon, delete the entries etc etc.
If anyone can describe how I can get CW to manage such devices properly and possibly even tell me how to stop it happening in the future it would be of great help.
Many thanks in advance (though I know some of you would rather have points ;-)
Scott
Hi Scott ,
Device will fall to " Devices not Configured in ACS " only in 2 condition :
1. Device is actually does not Exist in ACS
2. It EXist in ACS with different IPADDRESS or HOST NAME.
There is no direct way to delete these devices once they are on the Not Configured
in ACS list. However, one workaround is:
Step 1. Create a dummy NDG group in ACS to include these devices.
Step 2. Delete the devices in DCR and then in ACS.
Note: In order to delete a device from DCR we need to follow this procedure:
1.- Go to Common Services >> Devices and Credentials >> Reports >>
Devices that are not configured in ACS and generate a report.
2.- Now that we have all the devices that we want to delete, please go to
Common Services
>> Device and Credentials >> Device Management and select all the devices
from CS (Common Services database).
3.- Click on Delete and a confirmation message will pop, agree to this.
I hope this will help you
Thanks
Afroj
Similar Messages
-
Cisco Works "Devices not configured in ACS"
Hi!
I have instaled Cisco Works ver. 4.3.1
I have added using the Device Discovery, my devices. Some of them where not configured already on ACS with the loopback address, that was the one on the discovery configurations. Because of that, i could not manage those devices, althoug i could authenticate on them. I then updated the ACS with the loopback address, and configured the router's to authenticate using the source-interface of the loopback.
The problem is that i keep not being able to manage this devices on the cworks, because the are still as "Devices not configured in ACS".
Can anyone help me here?
Regard's
Miguel AmaralHi,
This happens, when you integrate the ciscoworks with ACS and Router/switches not configured with ACS. Try to reconfigure the device in ACS, try removing and adding it again in common services...Try for a single device and check it out... Try stopping/starting cw services after that // net stop crmdmgtd, net start crmdmgtd. Revert with the results.. -
I have some devices in my LMS 3.2 Master-Slave ACS-mode, that are, according to the DCR and AAA portlet, not configured in ACS
However I have checked that the devices are in ACS (in NDG and based on ip addresses, unique or by using wildcards)
What could be the reason why LMS can't find the devices in ACS?Hi,
If you have configured the devices in ACS and the LMS and ACS intergrity has been done then we need to break the integrity and redo it once again.
break the ACS and cisco works integrity, restart the deamons and then integrate it once again.
Please let me know if it helps.
Regards,
podhillo -
All DMG files "device not configured"??
Alright, this just did start happening. All the dmg files that i try to open, i get the same error. A warning box comes up, and it says, "The following disk images failed to mount" Then it lists the name of the device, example..."vlc-0.8.5.dmg"...and then shows a reason, which is, for all of them, "device not configured". I also get errors when trying to update to the newest os x as well. Anyone know what to do?
HELP!!!!!!!!! PLEASE!!!!!!!!!!!!!
I've mis-read your post, had similar issues to the person who wrote the original querie, copied these items;
/System/Library/Extension.kextcache
and
/System/Library/Caches/com.apple.kernalcaches/
to my desktop, removed them from their folders and restarted. Well, tried to restart.
The grey screen came up with the spinning gear and apple logo, then black text over laying that saying something about a stack error. I can't start my machine at all, not even from the OSx disk. It gets to Preparing Installation and keeps on spinning!
If any one can help I'd be eternally grateful. I can't believe this has happened!
Cheers
Kirstin -
hi
ive recently downloaded firefox 2.0 and some openoffice onto my ibook, but when I try to launch the .dmg files i get a 'device not configured' error message. can anyone help? apologies if this is far too easy.
thanks in advance
johnNot sure about FireFox specifically, but .dmg files should open and expand/mount automatically when you double-click on them. Make sure FireFox completely downloaded the file, and use Get Info from the File menu to check permissions to make sure you have read/write access to the file. If that doesn't work, try launching Disk Utility to see if it will recognize and mount the file from there, or see if you can verify the CheckSum (basically make sure the file is not corrupt).
Other than that, I'm stumped. -
Open Error 6: Device not configured
I recently had my hard drive replaced and restored to factory settings. I then used a time machine backup and the Migration Assistant to get everything I had back to where it belonged.
Things worked for a day or so, but with a few crashes here and there. Yesterday, I tried to use iTunes and kept getting an error message about the database (-50, unable to mount database). The problem is that the whole system would freeze and I had to shut down and restart every time. Sometimes I could load the OS, sometimes not. This morning I ran Disk Utility to verify the disk (it passed) and the permissions. When I tried to repair permissions, I got hundreds of messages like this : "Open Error 6: Device not configured on" and then a list of paths, such as "System/Library/Perl/5.10.0/darwin-thread-multi-2level/auto/POSIX/getgrgld.al", and "System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/share/ri/....." etc. Literally hundreds of those messages.
Does anyone know what this means? And how should I fix it?!?
Thanks!I'm going to suggest that you ask in the Snow Leopard forums here:
http://discussions.apple.com/category.jspa?categoryID=263
This is likely a system software error, and the SL gurus that hang out over there might have suggestions for you.
Good luck! -
Disk Utility Restoring Error - Device not Configured
Hi all,
A mate has given me a USB flash drive that doesn't work. I tried to create an backup image using Resuce Pro from SanDisk and it came up with a NDIF file. What I then did was partioned an external hard drive and restore using the image as source and the new partition as destination. 2 seconds later an error comes up saying restore error, could not validate source - device not configured. Am I the only one that has this problem or have I done anything wrong during the process?
Cheers,
KeefeNDIF is an obsolete format. You'd probably have to convert it to some kind of DMG first (Images > Convert.)
-
Ciscoworks: Device not appearing in Campus Manager
Hello,
I have added 3 new devices in CS and then create a group in RME then add the 3 devices in this group. Then I have run the credential check added devices in inventory and backup the configuration successfully.
Problem:
These devices are not appearing in the CM, In can see a new group but when I generate a User Tracking Report in Campus Manager, I am getting a popup saying "no end host found"
Device type are one 3750g-24ts switch and two 2611 routers.
I have restarted the services twice via net stop crmdmgtd; net start crmdmgtd, but no gain.
Please guide me that how I can make the devices appear in CM, there are many other devices already exist in CM. Also we only add devices manually, bot via discovery.
I am using
LMS: 3.2
CM: 5.2.1
RME: 4.3.1I have run the Data Collection in Campus Manager 3 times but still unable to see the 3 devices in campus manager.
Also it seems that CM is talking with CS as for trial I have deleted 1 switch from CS and it also get deleted in CM & RME
Please advise any other solution. -
GONE FROM DEVICE NOT CONFIGURED TO BROKEN MACHINE. PLEASE HELP!
HELP!!!!!!!!! PLEASE!!!!!!!!!!!!!
I read a post in response to a query from someone who I had similar issues to and copied these items;
/System/Library/Extension.kextcache
and
/System/Library/Caches/com.apple.kernalcaches/
to my desktop, removed them from their folders and restarted. Well, tried to restart.
The grey screen came up with the spinning gear and apple logo, then black text over laying that saying something about a stack error. I can't start my machine at all, not even from the OSx disk. It gets to Preparing Installation and keeps on spinning!
If any one can help I'd be eternally grateful. I can't believe this has happened!
Cheers
KirstinYou would have to boot in single-user mode, mount the filesystem and copy the files back into the extensions fiolder. I'm not going to type the whole procedure out here but some Googling will get you the exact instructions.
If you have your OSX installer disk "System Restore" might fix it. If not, there is a Terminal application on the Installer disk that would be easier to use than Single-user mode.
In any case, you are really dealing with one file since the cached file is probably irrelevant. -
HP 4385 all in one returns message "This device not configured for networking"
This happens just after the point in the install when I have attached USB and wireless data seemingly has been transferred to the Printer. This all started when I needed to do a re-install after a Vista upgrade.
I did reset the printer to Factory settings. I am using latest install software from HP Site. I have tried to resolve this with HP CHAT with no luck. Obviously I have tried this install several times now I even tried it with the printer within inches of my router.
Help PleasePrint a Wireless Test from the front of the printer. It will self-test the components of the printer, including its radio.
1. Press the Wireless button on the front of the HP All-in-One.
2. Press the button next to the icon on the display until Wireless Network Test is highlighted, and then press the button next to OK. The Wireless Network Test prints.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
hi team,
I am runing ACS 5.3 version and i am getting error messages like below
System Alarm [Database Purging]
Mon Sep 09 04:00:00
Incremental Backup Not Configured
System Alarm [Database Purging]
Sun Sep 08 04:00:00
Purge Configuration Repository not configured
Cause:
Purge Configuration Repository not configured
Details:
Configure Remote Repository under Purge Configuration which is used to take a backup of data before purge.
Cause:
Incremental Backup Not Configured
Details:
Incremental backup is not configured. Configuring incremental backup is necessary to make the database purge successful. This will help to avoid disk space issues. View database Size is 1.27GB and size it occupies on the harddisk is 1.22GB.
Could any one provide solution to overcome this issue.Hi,
I guess I've seen this before even we've repository and incremental backup configured fine on ACS. One reason could be for the above alarms is the configuration on the GUI might not have taken over completely in the database and alarms will trigger due to that. Please restart the services of the ACS or reload the ACS in off production hours.
acs stop
acs start
OR
reload
~BR
Jatin Katyal
**Do rate helpful posts** -
Error 633: The modem (or other connecting device) is already in use or is not configured properly.
Hi all,
I recently got that a new USB CDMA modem which works fine on Windows 7 system but when I try connecting to my other laptop which runs on Windows 8.1, it keeps giving the error:
Error 633: The modem (or other connecting device) is already in use or is not configured properly. I've most of the links and solutions shared but none seems to work. I've generated diagnostic logs which are as follows. I interpreted some and most probably
it seems like an issue of incompatible driver, but does anyone else sees any issues in these diagnostic logs. Looking forward to your suggestions.
[4724] 06-01 20:01:56:314: ENTRY: Reading "Reliance Netconnect+"
[4724] 06-01 20:01:56:315:
Before LoadPortsList2 in ReadEntryList()
[4724] 06-01 20:01:56:315: LoadPortsList2
[4724] 06-01 20:01:56:315: GetRasPorts
[4724] 06-01 20:01:56:315: RasPortEnum...
[4724] 06-01 20:01:56:315: RasPortEnum=603,c=10
[4724] 06-01 20:01:56:315: RasPortEnum...
[4724] 06-01 20:01:56:315: RasPortEnum=0,c=10
[4724] 06-01 20:01:56:315: RasGetDevConfig
[4724] 06-01 20:01:56:316: RasGetDevConfig=603
[4724] 06-01 20:01:56:316: RasGetDevConfig
[4724] 06-01 20:01:56:316: RasGetDevConfig=0
[4724] 06-01 20:01:56:316: SanitizeUnimodemBlob: mdm prot=0
[4724] 06-01 20:01:56:316: Port=COM17,fHw=0,fEc=0,bps=921600,fSp=0,prot=0
[4724] 06-01 20:01:56:316: StringCchCopy failed due to error 0x8007007a
[4724] 06-01 20:01:56:317: LoadPortsList=0
[4724] 06-01 20:01:56:317: successfully finished LoadPortsList2 in ReadEntryList()
[4724] 06-01 20:01:56:317: Reading media group "serial"
[4724] 06-01 20:01:56:317: New link format
[4724] 06-01 20:01:56:317:
DUPTEST:Port in this media
[4724] 06-01 20:01:56:317: Port=COM17
[4724] 06-01 20:01:56:317:
Trying to match the phonebook port in the system ports
[4724] 06-01 20:01:56:318: Port configured
[4724] 06-01 20:01:56:318: SetDefaultModemSettings(bps=921600)=1
[4724] 06-01 20:01:56:318: Reading device group "modem"
[4724] 06-01 20:01:56:318: Device List after deleting dupe
[4724] 06-01 20:01:56:318: StringCchCopy failed due to error 0x8007007a
[4724] 06-01 20:01:56:318: Fix entry type, 0 to 1
[4724] 06-01 20:01:56:318: Device List after deleting dupe
[4724] 06-01 20:01:56:318: ReadRasFile: ReadEntryList returned 0
[4724] 06-01 20:01:56:318: RASSQM: In ReadPhonebookFile Number of myuse profiles set 1
[4724] 06-01 20:01:56:318: ReadPhonebookFile returns 0
[4724] 06-01 20:01:56:318: RasGetAutodialAddressW
[4724] 06-01 20:01:56:318: RasGetAutodialAddressW
[4724] 06-01 20:01:56:318: DwEnumEntryDetails done. 0
[4724] 06-01 20:01:56:318: RasGetEntryPropertiesW
[4724] 06-01 20:01:56:318: IsRasmanServiceRunning=1
[4724] 06-01 20:01:56:318: IsRasmanServiceRunning=1
[4724] 06-01 20:01:56:318: GetPbkAndEntryName
[4724] 06-01 20:01:56:318: ReadPhonebookFileEx: called for pbk C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk, flags 8
[4724] 06-01 20:01:56:318: IsPublicPhonebook=0
[4724] 06-01 20:01:56:318: path=C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:56:318: full path=C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:56:318: IsVirtualizationNeeded: return value = 0
[4724] 06-01 20:01:56:319: ENTRY: Reading "Reliance Netconnect+"
[4724] 06-01 20:01:56:319:
Before LoadPortsList2 in ReadEntryList()
[4724] 06-01 20:01:56:319: LoadPortsList2
[4724] 06-01 20:01:56:319: GetRasPorts
[4724] 06-01 20:01:56:319: RasPortEnum...
[4724] 06-01 20:01:56:319: RasPortEnum=603,c=10
[4724] 06-01 20:01:56:319: RasPortEnum...
[4724] 06-01 20:01:56:319: RasPortEnum=0,c=10
[4724] 06-01 20:01:56:319: RasGetDevConfig
[4724] 06-01 20:01:56:320: RasGetDevConfig=603
[4724] 06-01 20:01:56:320: RasGetDevConfig
[4724] 06-01 20:01:56:320: RasGetDevConfig=0
[4724] 06-01 20:01:56:320: SanitizeUnimodemBlob: mdm prot=0
[4724] 06-01 20:01:56:320: Port=COM17,fHw=0,fEc=0,bps=921600,fSp=0,prot=0
[4724] 06-01 20:01:56:320: StringCchCopy failed due to error 0x8007007a
[4724] 06-01 20:01:56:322: LoadPortsList=0
[4724] 06-01 20:01:56:322: successfully finished LoadPortsList2 in ReadEntryList()
[4724] 06-01 20:01:56:322: Reading media group "serial"
[4724] 06-01 20:01:56:322: New link format
[4724] 06-01 20:01:56:322:
DUPTEST:Port in this media
[4724] 06-01 20:01:56:322: Port=COM17
[4724] 06-01 20:01:56:322:
Trying to match the phonebook port in the system ports
[4724] 06-01 20:01:56:322: Port configured
[4724] 06-01 20:01:56:322: SetDefaultModemSettings(bps=921600)=1
[4724] 06-01 20:01:56:322: Reading device group "modem"
[4724] 06-01 20:01:56:322: Device List after deleting dupe
[4724] 06-01 20:01:56:322: StringCchCopy failed due to error 0x8007007a
[4724] 06-01 20:01:56:322: Fix entry type, 0 to 1
[4724] 06-01 20:01:56:322: Device List after deleting dupe
[4724] 06-01 20:01:56:322: ReadRasFile: ReadEntryList returned 0
[4724] 06-01 20:01:56:322: RASSQM: In ReadPhonebookFile Number of myuse profiles set 1
[4724] 06-01 20:01:56:322: ReadPhonebookFile returns 0
[4724] 06-01 20:01:56:322: DuplicatePhoneNode
[4724] 06-01 20:01:56:322: GetPbkAndEntryName. rc=0x0
[4724] 06-01 20:01:56:322: GetInstalledProtocolsEx=0xc.
[4724] 06-01 20:01:57:690: DwEnumEntryDetails
[4724] 06-01 20:01:57:690: IsRasmanServiceRunning=1
[4724] 06-01 20:01:57:690: IsRasmanServiceRunning=1
[4724] 06-01 20:01:57:690: ReadPhonebookFileEx: called for pbk C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk, flags 8
[4724] 06-01 20:01:57:690: IsPublicPhonebook=1
[4724] 06-01 20:01:57:690: path=C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:690: full path=C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:690: IsVirtualizationNeeded: return value = 1
[4724] 06-01 20:01:57:690: GetLUAPhonebookPath: Return value 0 hiddenpbk path C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\_hiddenPbk\rasphone.pbk
[4724] 06-01 20:01:57:690: ReadRasFile: ReadEntryList returned 0
[4724] 06-01 20:01:57:690: SyncMasterPhonebookFile:++
[4724] 06-01 20:01:57:690: IsPublicPhonebook=1
[4724] 06-01 20:01:57:690: path=C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:690: full path=C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:690: FindFirstFile failed with 0x2
[4724] 06-01 20:01:57:690: ReadRasFile: File C:\ProgramData\Microsoft\Network\Connections\Pbk\rasphone.pbk does not exist
[4724] 06-01 20:01:57:690: DeleteEntriesOnlyInHiddenPhonebookFile ++
[4724] 06-01 20:01:57:690: WritePhonebookFile
[4724] 06-01 20:01:57:690: ModifyEntryList: Number of connections written 0
[4724] 06-01 20:01:57:690: RASSQM: In WritePhonebookFile Number of alluser profiles set 0
[4724] 06-01 20:01:57:690: DeleteEntriesOnlyInHiddenPhonebookFile : WritePhonebookFile failed with 0
[4724] 06-01 20:01:57:690: RASSQM: In ReadPhonebookFile Number of alluser profiles set 0
[4724] 06-01 20:01:57:690: ReadPhonebookFile returns 0
[4724] 06-01 20:01:57:691: IsRasmanServiceRunning=1
[4724] 06-01 20:01:57:691: IsRasmanServiceRunning=1
[4724] 06-01 20:01:57:691: ReadPhonebookFileEx: called for pbk C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk, flags 8
[4724] 06-01 20:01:57:691: IsPublicPhonebook=0
[4724] 06-01 20:01:57:691: path=C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:691: full path=C:\Users\lavi\AppData\Roaming\Microsoft\Network\Connections\Pbk\rasphone.pbk
[4724] 06-01 20:01:57:691: IsVirtualizationNeeded: return value = 0Hi,
We could get more information about your problem through this log. While, for your problem, first of all, it would be better to contact USB Modem manufacture to confirm its compatibility with Windows edition.
After that, make sure its driver was upgraded to be latest.
Roger Lu
TechNet Community Support -
Configuring Device - Device not reachable
My new Envy 4500 _IS_ on my network.
My new MacBook Pro _IS_ on my network.
I get to the configuration step and all looks good until I get the response below:
"Configuring Device
0 Select Device
0 Confirm Wreless Settings
O Select Network
Configuring Device
Configuration Results
Device Not Reachable
Th) wireless network settings were successfully downloaded to your device. However, your Mac
was unable to locate the device on the network.
Please make sure that:
• Your Mac is connected to a wired or wireless network that has access to your device.
• Your device is connected to the wireless network "AC Network".
Fomore information online, visithftp://www.hp.com/o/wirelessprinting"
This is the second HP printer that I am trying to configure that is doing the same darn thing. I thought the first one was faulty, so I exchanged for a slightly different printer. This one has a control screen, so I KNOW that it's on the network. And I KNOW my computer is on the network, or I wouldn't be able to write this.
But they refuse to talk with each other. SO frustrating. I'm ready to give up on HP.
Joe
This question was solved.
View Solution.Found the problem. HP printers don't support AC Wifi. That would have been nice to know before I wasted 4 hours on 2 printers......
-
Import Configuration as real device not simulated
Hoping there is a way for this.
We have multiple DAQs and multiple computers that can be used in any configuration at any time. One computer has all the DAQs in NIMAX loaded. We would like to be able to grab any computer use any VI and use it with no worries of configuration (DAQ1 is DAQ1 on each computer).
I backed up the configuration file on the main computer, and attempted to export it on another. It states that all the devices will be simulated on the new computer. If they are simulated in NIMAX, correct me if I'm wrong, when I connect the real daq to that computer it will create a new device assigning it a new number, and therefore not allow the VI to work without re-configuration. Am I correct on this? How do I get around this?NIerrors wrote:
I backed up the configuration file on the main computer, and attempted to export it on another. It states that all the devices will be simulated on the new computer. If they are simulated in NIMAX, correct me if I'm wrong, when I connect the real daq to that computer it will create a new device assigning it a new number, and therefore not allow the VI to work without re-configuration. Am I correct on this? How do I get around this?
When you add a read card, just delete the simulated device and configure the real one to be whatever name you need it to be. Shouldn't take more than 2 minutes (including the loading of MAX).
Or if you really want to play it safe, delete the simulated device and then reimport your DAQ configuration.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines -
Ocrcheck shows Device/File not configured
Hi All,
I'm new to RAC administration. I just found this command and try to run in my system and this is the output.
./ocrcheck
Status of Oracle Cluster Registry is as follows :
Version : 2
Total space (kbytes) : 262120
Used space (kbytes) : 8236
Available space (kbytes) : 253884
ID : 979000182
Device/File Name : /u08/quorum/Quorum
Device/File integrity check succeeded
Device/File not configured
Cluster registry integrity check succeeded
What might have been wrong with the setup?
I am using 10gR2 and Oracle Cluster file system 2 (ocfs2): ocfs2-2.6.9-42.ELsmp-1.2.4-2.x86_64
running in 2.6.9-24-ELsmp RHEL4 AS OS.
Any help will be appreciated.
Thanks,
Jay Aoh ! sorry
if you use Oracle Server - Enterprise Edition - Version: 10.2.0.3
metalink Doc ID: 467216.1 Version: 10.2.0.3
This problem can occur on any platform.
# ocrconfig -replace ocr /dev/raw/raw4
PROT-1: Failed to initialize ocrconfig
ocrcheck
Status of Oracle Cluster Registry is as follows :
Version : 2
Total space (kbytes) : 293640
Used space (kbytes) : 4596
Available space (kbytes) : 289044
ID : 136413798
Device/File Name : /dev/raw/raw1
Device/File integrity check succeeded
Device/File not configured
Cluster registry integrity check succeeded Cause:
ocrconfig -replace can't be used to replace the only online OCR disk
As only 1 active OCR is available, -replace will not work.Solution:
1. Add a mirror:
#ocrconfig -replace ocrmirror /dev/raw/raw5
2. Replace the OCR:
#ocrconfig -replace ocr /dev/raw/raw4
3. Remove the mirror /dev/raw/raw5
#ocrconfig -replace ocrmirror
Maybe you are looking for
-
How can I display the value of the Target Currency variable in my query
We have a query which has a key figure set to prompt for a Target Currency at runtime. Because the user did not want the currency displayed in each cell they used the NODIM function to remove it. They do however want to display the Target Currency i
-
Hello! I am using a proprietary IDE environment to compile some applications. I cannot change the following SQL query it performs. During "Compile", the IDE is checking the DB Function calls in the app by executing the following SQL Statement: select
-
A smart collection of: rating is not * (1 star) should return images including those with no stars, but does not. (It only returns items with 2,3,4 or 5 stars). Mike.
-
Re Editing Media Manager Files
I worked on a project a few years back and now need to go back in to my files and re edit something... is it possible to re edit something using my media manager files? I've been able to re import the MM files but whenever I touch the footage or try
-
Speakers sound issue on Envy 14 Beats Edition
Hi all, For few days now, my one year Envy 14 has a weird speakers sound issue. When the sound level passes over 50%, there is a lot of scratches and distorsion on the speaker, in that case, it is not usable at all. Note that this issue does not happ