CiscoWorks Syslog and TFTP servers

Hi!
Is it possible to disable CiscoWorks syslog and tftp servers and thus
free ports 514 and 69 for other applications?
Thank you,
Oleg Tipisov,
REDCENTER,
Moscow

The problem is that I don't know what service needs to be stopped.
Do I need to kill the process (crmlog, crmtftp) ?

Similar Messages

Call Manager TFTP Servers

I have a campus Call Manager solution going in place and want to confirm TFTP server redundancy, or the lack thereof.
Our design has three Call Managers; a publisher/TFTP and two subscribers. I would like to elect one or both of the subscribers as backup TFTP servers. Can the phones support multiple TFTP servers through DHCP config? If not, what are our other options?
Thanks in advance,
Brian Carscadden
SE Manager/Sr. Engineer
TransNet Corporation

Hi Craig,
Yes you can use two TFTP servers for redundancy, read the deatils in the CUCM design guide at the link below, make sure to read the note too. The link is for CUCM ver 6.0 scroll down a bit to read about DHCP and Option 150.
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/srnd/6x/netstruc.html#wp1043809
Thanks
Ovais

Ciscoworks syslog collector issue

Hi All,
In a central location i have a ciscoworks syslog collector version 3.5. The issue is not all the logs generated in the device are collected by ciscoworks including the devices connected in LAN. The major issue is on Cisco6500 series switches where i see multiple interface flaps in log but only few are found in syslog.
Regards,
Sathvik

Hi,
check here Admin > Collection Settings > Syslog > Syslog Collector Status , see if messages are falling under fitered or Invalid
then check the filter:
Admin > Network > Notification and Action Settings > Syslog Message Filters
I would suggest you to create a filter with all * and see if that helps.
you can look at this thread as well:
https://supportforums.cisco.com/thread/2244888?tstart=60
Thanks-
Afroz
[Do rate the useful post]

Percentage of Phones won't register after CUCM 9.1.2 Sub and TFTP failover

Hoping this has happened to someone else and they can shed some light on the subject. I have a CUCM 9.1.2 cluster running, pub, 2 subs, and 2 tftp servers. At the moment it's a small deployment so I have all phones registered to sub 01 as primary and using tftp01 as the primary tftp server. In order to have some VMWare maintenance done I recently shut down the pub, primary sub and primary tftp server forcing the phones to use the other half of the cluster. Everything there worked as expected, phones failed over, etc. The problem occurred after the VMWare maintenance was done. At that point I brought up the Pub and the primary sub (maintenance wasn't yet completed on the host that contained the primary tftp server). After the primary sub was up and back online is where the problem started. Random phones (all 8945 SIP that are all running the same firmware version SIP8941_8945.9-3-2-12) would just not register. Some of them would show registered in CUCM, however they were non-functional as DNs weren't displayed, no dial tone, etc. Others would just not register all together. In order to get a phone to register I had to perform a factory reset on the physical phone, if I did that they came back with no problem. Later after the maintenance was completed on the host that contained the primary tftp server and I brought that back online, I still had issues with phones however just a power cycle was enough to get those phones registered. I opened a TAC case one this but it ended up at packet captures and at that point ever phone I reset would just register correctly so I could never get an example of a phone that wouldn't register.
I'm convinced it's certificate related and having to do with the trust list, which is why I believe the factory reset on the phone would allow the phone to correctly register. There just doesn't seem to be any clear indication as to why it would be certificate related. Names weren't changed on any of the UC servers, VMWare version was upgraded from 5.0 to 5.1 but I can't see how that would have caused certificate issues.
Any help would be grateful or if this has also happened to anyone I'd love to hear what you did to resolve this as for future maintenance windows I have to be confident that phones will be able to fail over between cluster nodes.
Thank you,
Alex

So the phone is unable to authenticate the ITL it is getting or the new config file. This could mean that the ITL is corrupt on one of the nodes or that TVS isn't working properly.
I would try running "show itl" on each node and check the bottom of the output to see if the ITL is verified successfully.
I would also make sure TVS is running on all nodes okay.
You also should be able to just delete the ITL from the affected phones rather than doing a full factory reset in case this comes up again.

CUPC - CTL does not match the configured TFTP servers -- need reset!

Hi,
i have trouble with CUPC 8. Presence 8.0.4. I tested all things, but i'm unable find solution.
Client say: Phone initialization has occured. CTL reset required.[1002]. In the core log from the CUPC is:
provider-runner] [ConfigService] [CUCMConfigSubService.updateCTL(633)] - CTL does not match the configured TFTP servers -- need reset!
but i don't know which CTL, and why CUPC use CTL for accessing tftp. I'm not using secure connection to the CCM.
Solution from release notes:
http://www.cisco.com/en/US/docs/voice_ip_comm/cupc/8_0/english/release/notes/cupc80.html#wp248810 is not working.
Has anybody some idea?
Risa

Some details for my trouble. Integration from CUPS and CCM from system troubleshooter is ok.
CCM has device type CUSF. But CUPC is not able connect to this softphone. CUPC client show error message from my first post. And in the core log from the CUPC are messages about softphone and downloading configuration file, but tftp connection failed. Log contain messages: Supplied TFTP address 192.168.10.3 is not in the CTL. // CTL does not match the configured TFTP servers -- need reset!
(same situation with hostname of CCM)
From release notes and description of this situation I tried erase old configuration from PC, but nothing change - same trouble.
Has anybody some idea, which CTL is used for authenticate tftp.
Thanks for response.
Richard

Bulk Phone Resets and TFTP Performance

I have approximately 1500 7941/61 phones in Callmanager 4.1(3)SR2 that are to be upgraded with the 8.0(3) phone load. I plan to reset the devices via device search (not device pool) and we want to know the estimated system impact and overall time to process all of the requests. We have a cluster of 3 7845 Callmanagers, all enabled for TFTP, with priority to sub2, sub1, Pub.

Thanks! This is the info I needed.
We actually ran the update last week with catastrophic results. Although we have three TFTP servers, they were set to the default of 200. Approximately 400 of the phones hung on the reboot, stopped dead and not registering to Callmanager, with no way to reset. We opened a P1 with TAC. They said the multiple TFTP servers should have handled the requests just fine (we're using three 7845s). Recommendation was to shut/no shut switchport interfaces to hopefully reboot the phones - no luck. Even reloading the switches didn't do it, because apparently there is still some power provided to the ethernet interface somehow. The ONLY sure fix was to unplug and reconnect each IP phone ... all 400 of them. In a college campus of 60-70 buildings and multiple IDFs per building let's just say is was a real long night. We're still not sure if this was a TFTP performance issue or an issue with the 7.0(2) to 8.0(3) phone loads.
Thanks again for your help.

Move and redeploy application- and web-servers for Planing?

Hi, all!
Have Hyperion Planing ability to move application- and web-servers from unix-machine to another win-machine and after redeploy existing unix-installed planing on it?

They are actually for for 2 different things. The Sun WAS is for enterprise applications, EJBs and the like.
Tomcat is for simpler Servlet/JSP hosting.
The Sun WAS actually uses the Tomcat server as its Servlet/JSP engine then adds EJBs on top.

How to use the same services-config for the local and remote servers.

My flex project works fine using the below but when I upload my flash file to the server I doesn't work, all the relative paths and files are the same execpt the remote one is a linux server.
<?xml version="1.0" encoding="UTF-8"?>
<services-config>
    <services>
        <service id="amfphp-flashremoting-service"
            class="flex.messaging.services.RemotingService"
            messageTypes="flex.messaging.messages.RemotingMessage">
            <destination id="amfphp">
                <channels>
                    <channel ref="my-amfphp"/>
                </channels>
                <properties>
                    <source>*</source>
                </properties>
            </destination>
        </service>
    </services>
    <channels>
    <channel-definition id="my-amfphp" class="mx.messaging.channels.AMFChannel">
        <endpoint uri="http://localhost/domainn.org/amfphp/gateway.php" class="flex.messaging.endpoints.AMFEndpoint"/>
    </channel-definition>
    </channels>
</services-config>
I think the problem is the line
        <endpoint uri="http://localhost/domainn.org/amfphp/gateway.php" class="flex.messaging.endpoints.AMFEndpoint"/>
but I'm not sure how to use the same services-config for the local and remote servers.

paul.williams wrote:
You are confusing "served from a web-server" with "compiled on a web-server". Served from a web-server means you are downloading a file from the web-server, it does not necessarily mean that the files has been generated / compiled on the server.
The server.name and server.port tokens are replaced at runtime (ie. on the client when the swf has been downloaded and is running) not compile time (ie. while mxmlc / ant / wet-tier compiler is running). You do not need to compile on the server to take advantage of this.
Hi Paul,
In Flex, there is feature that lets developer to put all service-config.xml file configuration information into swf file. with
-services=path/to/services-config.xml
IF
services-config.xml
have tokens in it and user have not specified additional
-context-root
and this swf file is not served from web-app-server (like tomcat for example) than it will not work,
Flash player have no possible way to replace token values of service-config.xml file durring runtime if that service-config.xml file have been baked into swf file during compilation,
for example during development you can launch your swf file from your browser with file// protocol and still be able to access blazeDS services if
-services=path/to/services-config.xml
have been specified durring compilation.
I dont know any better way to exmplain this, but in summary there is two places that you can tell swf about service confogiration,
1) pass -services=path/to/services-config.xml parameter to compiler this way you tell swf file up front about all that good stuff,
or 2) you put that file on the webserver( in this case, yes you should have replacement tokens in that file) and they will be repaced at runtime .

Issue with VPN configuration in Windows 2008 r2 and 2012 Servers.

Hello ,
I hope you can help me to fix this issue, it's been 5 days since I a, trying to configure VPN in your 2008 and 2012 Servers. On both platform (2008 and 2012) I am getting same error while configuring VPN (after role installation).
"Unable to load C:\Windows\System32\iprtrmgr.dll". So, I have removed IPv 6 entry from the registry and now able to start server (not sure what configuration it took automatically). I tried to disable "Routing
and Remote Access" service and got the same error while enabling "Routing and Remote Access" is running but VPN is still not functioning properly).
I am getting following error,
================================================
Errors under the Event viewer (Remote access)
1) --->> CoId={DF744409-02D7-4FF4-AD24-504F0C83E1AB}: The user 10.0.0.1\chetan connected from 10.0.0.1 but failed an authentication attempt due to the following reason: The remote connection was denied because the user name and password
combination you provided is not recognized, or the selected authentication protocol is not permitted on the remote access server.
2) ----->> CoId={DF744409-02D7-4FF4-AD24-504F0C83E1AB}: The user connected to port VPN3-127 has been disconnected because the authentication process did not complete within the required amount of time.
Errors under the Event viewer (Remote access)
3) ---->> Network Policy Server denied access to a user.
Contact the Network Policy Server administrator for more information.
================================================
I am using (MS-CHAP v2) + EAP (Authentication Method). Please let me know if you need any additional information.
Thank you,

I Guess this thread is not related to SQL Server .User is facing issue because of network or may be due to OS.I guess I will move this into windows forum.
Moderators please move to Network forum
Please mark this reply as the answer or vote as helpful, as appropriate, to make it useful for other readers

Active Directory domain migration with Exchange 2010, System Center 2012 R2 and File Servers

Greeting dear colleagues!
I got a task to migrate existing Active Directory domain to a new froest and a brand new domain.
I have a single domain with Forest/Domain level 2003 and two DC (2008 R2 and 2012 R2). My domain contains Exchange 2010 Organization, some System Center components (SCCM, SCOM, SCSM) and File Servers with mapped "My Documents" user folders. Domain
has about 1500 users/computers.
How do u think, is it realy possible to migrate such a domain to a new one with minimum downtime and user interruption? Maybe someone has already done something like that before? Please, write that here, i promise that i won't ask for instruction from you,
maybe only some small questions :)
Now I'm studying ADMT manual for sure.
Thanks in advance,
Dmitriy Titov
С уважением, Дмитрий Титов

Hi Dmitriy,
I got a task to migrate existing Active Directory domain to a new froest and a brand new domain.
How do u think, is it realy possible to migrate such a domain to a new one with minimum downtime and user interruption?
As far as I know, during inter-forest migration, user and group objects are cloned rather than migrated, which means they can still access resources in the source forest, they can even access resources after the migration is completed. You can ask users
to switch domain as soon as the new domain is ready.
Therefore, there shouldn’t be a huge downtime/interruption.
More information for you:
ADMT Guide: Migrating and Restructuring Active Directory Domains
https://technet.microsoft.com/en-us/library/cc974332(v=ws.10).aspx
Best Regards,
Amy
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]

Upgrade process for SQL server 2005 service pack4 on stand alone and cluster servers

Hi All,
We have iniated a process of upgarding sp4 for all sql 2005 stand alone and clusters servers.
Please provide me the step by step process for installing sp4 and roll back paln for sql 2005 servers.And before proceeding with sp installation what are the pre check/pro active things that we need to take care.
Maheshwar Reddy

Hello,
For applying SP to SQL 2005 cluster environment/standalone please refer to below link
http://www.sqlcoffee.com/Tips0007.htm
Please mark this reply as the answer or vote as helpful, as appropriate, to make it useful for other readers

Slow transfer speed between existing servers and new servers

I have an issue with copying files to a new HP physical server with Esxi 5.5 host and Windows 2012 Server from anywhere in our current network.
We have an older HP server with Esxi 3 and multiple Windows 2003 vms, including a domain controller, file server and sql server (our current environment).   I installed a new HP DL380 Gen 8 server and installed Esxi 5 and two Windows 2012 servers,
one is a DC and one is a file server (our future environment).
Currently the new 2012 DC a second domain controller; have not made it the first domain controller yet.   The 2012 file server is a member server. Same network IP range, static, same subnet, same gw.
When I try to copy files from our current environment – to either of the Windows 2012 servers it crawls, like 100kb/sec or less.   It is slow between 2003 and 2012 servers, either direction, and between my Windows 7 and the 2012 server. Does
not matter if I use windows to copy or robocopy. It is very fast between the 2003 servers in the current environment and between my windows 7 and the current servers. Downloads from the Internet do not seem slow. I have done the following
to try to resolve with no success:
Some forums have suggested disabling Large Send offload on the nic card – usually Broadcom cards, ours are intel, but I tried it anyway with no success.
Some forums suggested turning off digital signing in group policy, no success.
Some forums suggest SMB2 can be a culprit, I disabled it on the 2012 server with no change in speed.
I made sure all the updates are complete on the new 2012 file server.
Turned the server firewall off to be sure it wasn’t blocking something; no antivirus installed yet.
I contacted Vmware to make sure the virtual switch and nics were set up correctly on Esxi 5, they said they are.
I checked the physical Cisco switch settings to make sure it looked fine.   The current and future physical servers were all connected to the same physical switch.
I switched out the network cable
I moved the network cable to a different switch.
I checked to be sure DNS was set up correctly.
I checked firewall settings on the Esxi 5.5.
Current HP Service pack is installed on the Gen 8 Server.
I am running out ideas. Any suggestions?

Hi,
Would you like to adjust to RSS, NetDMA and TCP Offload?
http://blogs.technet.com/b/networking/archive/2008/11/14/the-effect-of-tcp-chimney-offload-on-viewing-network-traffic.aspx
Hope this helps.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Advantages of using a webserver inbetween a load balancer and application servers

I am building out a new weblogic domain.
I am wondering which one of these configuration to go with:
1. Load balancer > weblogic servers
2. Load balancer > web server > weblogic servers
Could someone tell me what are the specific advantages of having web servers inbetween a load balancer and application servers (besides caching static data content and acting as a proxy)?
Thanks in advance
Srini

Other than hosting the static content, nothing much really. We have our load balancer go straight to WL for applications without static content and route to web server if there is static content. Easy enough to do it both ways, best of both worlds.

IDE's and webservers and application servers

can anyone please tell me what exactly are the IDE's,webservers and application servers in java
1.eclipse
2.IDEA
3.JDeveloper???
jboss
jbuilder..

PubeHow much thrust does the Pube produce?no idea. it's not really about the power, it's a nice green eco-car, 100% recycled. it's made from old corsairs*
*old coarse hairs boom boom

Admin and Task servers as one in the same

I open up the Remote Desktop software, and select 1 computer from the list. I then click on the "Install" icon and drag a .pkg file inside of the "Packages" area. I check off the radio button that says "Run this task from: The Task Server on this computer" and click the "Install" button.
I get a progress bar that runs infinitley and a message that says "The targetd computer, "<computer name>", is currently idle. It doesn't matter if the computer is up and running, or if it is offline. It says the same thing regardless and never installs the package.
If I decide not to "Run this task from: The Task Server on this computer" and instead "Run this task from: This application" then it works prefectly. I just can't seem to install from the local task server, which means I have to wait until this machine is online before I can manually run it, which means there's a problem with the way I set up the Task server.
Does anyone have any idea what's wrong with my installation? I have gone into "Remote Desktop -> Preferences -> Task Server" and made sure "Use Task Server on this computer" was selected, and it is. I am NOT using 2 different serial number for 2 different and separate copies of ARD3 for both an Admin + Task Server. I am, however, expecting the Task Server and Admin Server to run as one in the same. If this is not possible then perhaps the Documentation needs updating? From http://images.apple.com/server/docs/ARDTaskServer.pdf I read: "You can run the Task Server on either the administrator computer or a dedicated remote computer. The default Task Server is the administrator computer on which you installed Remote Desktop.". This means the Admin and Task Servers can run as one in the same, no? Please let me know if this is incorrect.

Update: Please refer to the post with the title of "Possible to run both an Admin Server and Task server from the same host?". Basically the answer to this problem is that there isn't one. I've called apple support and it's been confirmed that an Admin server and Task server CANNOT be run from the same installation on the same host. I suppose you could say the answer is to buy another license of ARD3 and run it in a separate host, but for some of us this isn't an option - especially for a very small startup.

CiscoWorks Syslog and TFTP servers

Similar Messages

Maybe you are looking for