Class charateristic assigned to master inspection charateristic

Hi Experts,
              I am working on a scenario as described below.
1. Create a chrateristic for pressure mesurement
2. Assign it to class
3. Create two types Master inspection chrateristic
     using class chrateristic & without class charateristic
4. Use both the MIC in Task list operation
5.Assign ispection point in task list , in my case Fun location
6. Create inpection order as use this task list in it
7. inspection lot is getting created
8. While doing the Result recording  the operation with MIC having class charateristic as ref is not coming
Can you please look in to it.
Regards
Amar

Hi Amar,
Can you pls check :
1. You have mention proper control key in your operations?
2.  You have maintained sampling procedures in task list.
3. Also check whether your MIC is in released state.
I hope you have done correctly for the above Q's, then,
4.  Check whehter you have not mentioned your both MIC to the same operation. Make two operations in task list and to each operations assign MIC.
Actually there is not much difference if you take ref or not. Only the parameters in class char will transfer while creating MIC (like lower spe limit upper sp limit ) but afterwards both are same as far as tasklist is concerned.
Regards,
Rajesh

Similar Messages

  • QM view material master (Inspection Type)

    Hi there,
                 I didn't understood the pragmatic usage of the check box <u><b>inspection by configuration</b></u> &  <u><b>inspection by characteristics</b></u>.......that can be set for the inspection types..........
    Please enlighten me ......
    Thanks
    Kaushik
    Message was edited by:
            Kaushik Choudhury

    If you set this indicator, the system takes the configurations from the sales or production order into account when inspection lots are created and changes or supplements the inspection specifications in the task list or material specification.
    The indicator only works for the following inspection lot origins:
    o   01 Goods recipt for purchase order
    o   03 Production
    o   04 Goods receipt for production order
    The indicator cannot be used for the inspection lot origins 10 and 11.
    Example
    When creating the sales order, the customer defines that the pH value of the product to be manufactured should be between 5.0 and 5.5. When an inspection lot is created for the resulting production order, this tolerance is then copied into the inspection.
    Dependencies
    The specifications are only copied into the inspection lot if there is a link between the class characteristic and a master inspection characteristic.
    Hope this helps you.

  • Date format in Master inspection characteristics

    Hi All
    I have a requirement where my user wants to enter the date format in the master inspection characteristic. For example we want to add date of manufacture and the date of expiree as a inspection characteristics and during the results recording they want to enter this characteristics in a date format.
    MY question is can we have a master inspection characteristic with a date format, if so what all the settings are required.
    Please suggest.
    Thanks,
    Quantum.

    >
    quantum wrote:
    >Can i use characteristics in the inspection plan instead of the master inspection characteristics. I am using Work bench transaction code CWBQM to create an inspection plan.
    Direct characteristic you can't use in inspection plan. If you want to use characteristic in IP then create chara. (CT04), then assign this charac. as class chanr.(QS21) in MIC. Now you can use this MIC in inspection plan.
    Hope this helps.
    Thanks!!!

  • Multiple class types for material master classification display default.

    Hello,
    We are running on R/3 4.7.  We use several different class types for our material masters (001 and Z01).  The problem this creates is the end user having to constantly tell the system which class type to use when going to the classification screen for different materials with different class types.  If a user views one material's classification page with a particular class type (001) then looks at another material with a different class type (Z01) the system tries to pull in information from the last materials class type (001).  The system tells the user there are no assignments for the class (001) in the material their viewing but there is one for class type (Z01).  The user then has to select the class type that applies to the material master their trying to view.  Is there a way for the system to automatically see when a material has only one class type assigned to it for it to automatically default it in without the user having to specify the class type?
    Thanks,
    JRW

    Hi,
    Check the configuration, have you maintained default class type for material type.
    Logistic General> Material Master> Basic Setting> Material Type> Define attributes of Material Types>Select the material type> Double click on material type--> Class type
    Edited by: P. Dhamane on Jun 4, 2010 3:21 PM

  • How can copy master inspection characteristic from plant1 to plant2

    Now I have 2 plants
    I already created all master inspection characteristic that i need by QS21 for plant1
    Is there any way I can copy all master inspection characteristic from plant1 to plant2 ?

    i'm creating inspection plan( QP01 ) for material ,  but all the materials & plans are in plant 2 (ss03)
    now i have to assign MIC to inspection plan , i only can select MIC of plant 1 ,and plant text would show"plant 1" ....
    so i want to create the same MIS for plant 2 , is there any way i can mass copy MIC from plant 1 to plant 2 ?

  • Combining Master inspection charac. of HALB & FERT in a Quality Certificate

    Dear Experts,
    material A (halb) with Inspection Plan1 produced  material B (fert) with inspection plan 2. Some of the Master Inspection Characteristics maintained in inspection plan 1 are not in inspection plan 2. I intend to create a Quality Certificate for material B (fert). How do i pick some charateristics from insp plan 1 (which is assigned to halb material A)  to display in addition to charateristics from insp plan 2 (assigned to fert material B). Characeristics from fert diplays in my Quality Cert, but how do i incorporate characteristics from the halb?

    You do this in the certificate profile.  Click on the button on the menu bar labelled "Materials".  In here you define what materials the system should look for to find the relevant batches or inspection lots.
    For this functionality to work, you must have the batch where used functionality set up.  I recommend having the batch where used list update in real-time rather then in batch.
    FF

  • Valuation class in the material master

    hi all, we maintain split valuation materials, namely domestic & imported. we are working on project based scenarion planning strategy 21 : MTO/project.
    in daily practice user convert unrestricted stock to project stock with 412 Q mvt type before MRP RUN.
    but for some when user try to convert stock following error occurs. I check stock available, it is available. but i do not understand why this error comes.                                                             
    Maintain the valuation class in the material master first
    Message no. M7232
    Diagnosis
    The system found that you have defined your own valuation classes for sales order stock and project stock in Customizing. However, these valuation classes have not been maintained in the material master record for the materials concerned.
    Procedure
    So that the relevant accounts can be posted upon goods movements, you have to maintain the valuation classes for sales order and project stock in the accounting view of the material master record for the material concerned.
    If you have authorization to do so, you can change the material master record.

    Hi,
    The normal valuation stock refer to relevant table valuation class field MBEW/MBEWH-BKLAS
    Special Sales Stock refert to MBEW/MBEWH-EKLAS
    Projeck Stock refer to MBEW/MBEWH-QKLAS
    Cheers,
    Girang

  • Valuation Class according to Material Master but not Plant wise

    Hi,
    Is there way to find out the Valuation Class according to Material Master but not Plant wise...
    Plant wise, we can get into MBEW table, but I want to find valuation class directly...
    Plz guide..

    I need to change Valuation class against material number...
    We have 18 plant in our company and more than 2,50,000 material's.
    Which one easy task for change in material master, either 2,50,000 material's or 2,50,000 X 18 (45,00,000) material list.
    If I go with plant wise, we need to change 18 times...also this is time consuming process... As I know in all Plant's, valuation class must be same...
    please guide...

  • Assigning a different inspection plan to an inspection lot

    Hi,
    I have a situation where the incorrect inspection plan is assigned to an inspection lot. Is there any mechanism to assign a different inspection plan to an inspection lot i.e. without having to reverse a goods receipt.
    Regards,

    >
    Shyamal Joshi wrote:
    > Hi Kaushal,
    >
    > There are more than one reason for this error. Check the followings.
    >
    > - The key date for inspection lot should be later than the key date for the inspection plan, later then the date when you assigned the material to the plan.
    > - The usage of lot and inspection plan should be same.
    > - The status of inspection plan must be released.
    >
    > Regards,
    > Shyamal
    Why are you not checking these things I am sure the reason would be there only. If dont wana check it is your wish. Any ways best of luck

  • What is the use of valuation class in Finished Material Master?

    Dear Expert
    What is the use of valuation class in Finished Material Master?
    Thanks of Advance

    hi,
    this is to inform you that,
    generally 7920 - will be the valuation class for the finished goods.
    Allows the stock values of materials of the same material type to be posted to different G/L accounts & vice versa.
    this is an integration field which identifies the G/L accounts & goods movement types.
    balajia

  • Config settings for Decimal places in Master Inspection Characteristics

    Hi,
    can any body tell me where to do the configuration settings for decimal places  in master inspection characteristics
    i want my limits to be 1.234
    i want 3 decimals after point
    Regards,
    Raj

    Hi,
    Please go through the below link.
    http://www.freesaptutorial.com/how-to-create-master-inspection-characteristic-in-sap-qm-module/
    While creating the MIC in QS21 after entering the control indicators you will get Quantitative data screen.
    In that screen you can enter the decimal places, UOM, target, lower limits etc
    Regards
    Hari

  • System not allowing to assign the master batch in Equipment

    Dear PM Guru's,
    I am trying to rotables managment process through installation and dismantling process. Material created with different valuation types and serial number profiles. Stock updated for valuation type REPAIRED & NEW. For TOBE REPAIRED, there is no stock updation. Now i want to update the stock by dismantling the equipment from superior equipment through IE4N. In IE4NCGP, i maintained the movementy types are 261(For installation) 262 (Dismantlation) and i am trying to execute IE4N transaction code. When i am trying to save the business transaction system throw following message "material document batch differ from equipment master batch". How we can assign the master batch? if its not in stock and its already installed in equipment i want to bring that one into stock as "TOBEREPAIRED" with movement type "262". I am requesting all the PM experts who ever done this process earlier please share the documents if possible.

    We want to enter only PAN number in XK01/ XK02. But the system is not allowing us to save until we enter all the details.
    Its not necessary that all Vendors will have CS, LST no. or Excise details. This is the reason I am looking for a way how to make these fields optional and I am fine with it as long as system does not give any error. Because system is not allowing us to save the Vendor master, I wanted to deactivate CIN in Vendor Master.
    Kindly suggest how to make the CIN fields optional. Your temporary solution (DOT) is working fine, still we want a permanent solution.

  • What is the IDOC for Master inspection Characterstics Creation/edit/Cancel

    Hi
    i need IDOC for this.....
    what is the IDOC for
    1.Master inspection Characterstics Creation
    2.Master inspection Characterstics Edit
    3.Master inspection Characterstics Cancel
    plz give ans very urgent
    bye
    suresh

    Check these..
    in TCode: we30
    ->INSPECTIONPLAN_CREATE01
    ->MATQM01
    ->QPMK01
    Regards,
    Ramesh.

  • T. Code for Master Inspection Lot

    Dear Friend
    Through which transaction code I can create master inspection characteristics for a material?
    Cheers
    Chandra

    Hi Dear
    Check this Tcode QS21---->Create master insp. characteristic
    Regards
    Ranga

  • Difference between Characterstics and Master Inspection Characterstics??

    Could some please explain me the difference between characterstics and Master inspection Characterstics?
    How do you create a new master inspection characterstics?

    Classification and Characteristics are cross-application functions ( [SAP Help|http://help.sap.com/saphelp_erp60_sp/helpdata/en/dd/ae56614bb411d192f20000e829fbc6/frameset.htm] ) used in many areas of SAP such as:
    - Equipment
    - Functional location
    - Notification
    - Task lists
    - Materials
    - QM master inspection characteristics
    - Sales orders
    - Etc
    PeteA

Maybe you are looking for