Clean Snow Leopard Install yields the Welcome Video to loop continuously

Has anyone seen this before?
Mac Mini (MA468LL/A) with a clean Snow Leopard Install. After I kicked off the install, I returned an hour later to find the Welcome Video looping continuously. There is a brief moment at the beginning (or end of the video) when I can move the mouse on the screen with a grey background.
Now, no keyboard combo's work at bootup. I can't boot to the DVD again, I can't clear the NVRAM, etc. I can eject the DVD, but only when the unit is looping the video.
Any help would be appreciated, Please!
PS - The only thing different from a typical install was this - I deleted the previous Leopard partition using the the Disk Utilities.
Message was edited by: GordonInCleveland

Welcome to Apple Discussions.
After ejecting the DVD and shutting down your Mac, can you restart normally? If so, then you could wipe the partition again and re-install.
Also, have you tried starting in single user mode. At the prompt type fsck -fyremember to leave a blank space before the "-fy".
This will run a file system check, like Repair Disk and repair any problems if it can. If you run into errors run fsck multiple times until it reports OK.
Then, type rebootreboot to restart to OS X.
-mj

Similar Messages

I want to install Yosemite onto an external hard drive, and keep Snow Leopard installed on the internal hard drive. I want to be able to boot from either system, depending upon circumstance (at least until Yosemite is stable). Is this possible?

iMac, Model Identifier iMac12,1 with 121.5" screen, 2.8 GHz Intel Core i7 processor, 8 GB 1333 MHz DDR3 memory, 1 TB internal hard drive, running Snow Leopard 10.6.8 from internal drive.
I want to install Yosemite onto a 1 TB external hard drive (OWC) , and keep Snow Leopard installed on the internal hard drive. I want to be able to boot from either system, depending upon circumstance (at least until Yosemite is stable). Is this possible?

It is possible. I'll let you read some articles that cover the setup:
Starting from an external USB storage device (Intel-based Macs) - Apple Support
or
http://osxdaily.com/2013/06/22/boot-mac-external-drive/

Can't get past the Welcome video - It loops over and over

Short and skinny
I bought a family pack
Installed on Intel iMac by clicking continue all the way through. Which makes it an upgrade right? That went flawlessly and all is good.
Now the problem.
I have a Intel MacBook that I tried to install Leopard on. I did want a fresh install because I just wanted to start from scratch. So I changed the option to do that. Started the installed and got the big check mark at the end of it. When I went to click "Continue" and it froze up. The countdown timer stopped at 23 sec. left and it sat there for 10 mins. frozen. I held the power button till it shut down. Turned it back on. I got the welcome video and then it asked to select language for the install.
No matter what I did, once I clicked the mouse button to contine, the pin wheel spins for a few seconds and the video starts over again. I did it about 10 times and it never passed that point.
I restarted it a few times with the same results. I thought I would try and do another install from scratch. I restarted it again holding down the C key till I got the first screen of the install. It let me select the options I wanted and continued to the install. After about 15 mins. or so it stopped and a screen popped up with a bunch of code on it. Tried THIS about 2 more times and by now it was about 3am and I was tired. I shut it down and this is where I am at. Its at home and I can't mess with it till I get off work.
Any advice on what I might try when I get home about 8pm tonight will be most helpful.
Thx, Jim

Any help???

After clean snow leopard install, ical crashes on startup

I just did a clean install of snow leopard and then restored from time machine backup. Now iCal crashes within 5 seconds of opening. I don't have a chance to make any changes or expeiment becuase it doesnt stay open long enogh.
I deleted the .plist enteries from ~library/preferences as advised in various forums, this has had no effect, positive or negative. I'm out of options.

I'd do this:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
If you are reinstalling an earlier version of OS X then download the Mac OS X 10.6.8 Update Combo to upgrade.
Just an afterthought: Do you have at least 1 GB of installed RAM (and preferably more.)

Time Machine Not Recognized After Clean Snow Leopard Install

I've searched for this particular question.
I was unhappy with Snow Leopard dragging. I wanted a clean install. I did not have the original snow leopard installation for my computer, so I got a different snow leopard DVD. This has apparently caused problems with time machine.
The clean install in complete. I am now ready to migrate my Time Machine backup onto my iMac24". However, Time Machine is not recognized--at least not in the way I want.
When I plug my time machine HD into the USB, snow leopard asks if I want to use this for future back-ups. I decline, because I specifically want to restore what has already been backed up. The HD is visible as an external device--and I can in fact see the raw data of my time machine backup stored in folders.
However, when I enter migration assistant, time machine is invisible. On the page where I am expecting to select time machine, I instead get a perpetually spinning circle icon.
I suspect time machine is "linked" to the prior snow leopard operating system, rather than to the computer ID. Obviously, this is a bit of a mistake on my part. However, I'm already into the breech and I've got no choice but to go forward.
Please advise how to redirect my time machine to its new master (same computer, different snow leopard registration)?
Thanks so very much.

Retail disk? Yes, it was the snow leopard CD.
I used a single license snow snow leopard CD install the first time around, when snow leopard was first released. At at that time I "upgraded" my system from leopard.
This time, I used a different physical disk with snow leopard with a family license. This time I did a "clean" install in which I first erased my hard drive using disk utilities.
There were no problems with the installation.
As I say, my time machine hard drive is "recognized" by the computer as an external drive. It just is not recognized when I utilize the migration assistant. It is also "recognized" as a time machine, but only as a potential time machine for prospective use to update going forward, whereas I want it to open up as a time machine for my iMac that I just wiped clean yesterday.
Thanks for your assistance.

Re-download Lion from clean Snow Leopard install

My hard drive and back up drive both died at the same time. Aside from that fiasco, I've now reinstalled Snow Leopard on my new hard drive and want to re-install my previously purchased Lion on it. There are many posts that indicated that all you need to do is hold down the option key while selecting to buy it from the App Store, but since this is not being done from Lion, I only get the option to re-purchase it. I can't believe they wouldn't have an option for re-downloading it when it's clearly tied to my Apple ID. Any ideas?

Thanks for the quick response. Unfortunately there is nothing listed for Lion. All my other apps are there. When I try to use the Option key and click on purchases or the Lion purchase button it only wants me to actually purchase it again for the full price. Its as though it was tied to the physical drive that is dead instead of my Applie ID.

Snow Leopard Install and the Grey Spinning Wheel

So, I purchased Snow Leopard (says it's 10.6.3) this afternoon, and after the very long install process, got stuck with the grey screen with the apple and the spinning wheel, and nothing further will happen. I read on a few other posts that doing the install again eventually fixed the problem, but I have tried 3 times now and nothing is working. I know this is a problem lots of people have had, but I haven't been able to identify the solution for it, and Apple is closed for the holidays. Any help would be appreciated.
BTW, I had been running Tiger, and I have a 13.3 inch Mac Book.

Do you have your original Tiger installation discs? If so then you can reinstall it if anything goes wrong. At this point you cannot clone the system since it no longer functions correctly, so it's best to simply backup your data so it isn't lost.
Five ways to eject a stuck CD or DVD from the optical drive
Ejecting the stuck disc can usually be done in one of the following ways:
1. Restart the computer and after the chime press and hold down the left mouse button until the disc ejects.
2. Press the Eject button on your keyboard.
3. Click on the Eject button in the menubar.
4. Press COMMAND-E.
5. If none of the above work try this:
Open the Terminal application in your Utilities folder. At the prompt enter or paste the following:
/usr/bin/drutil eject.
If this fails then try this:
Boot the computer into single-user mode. At the prompt enter the same command as used above. To restart the computer enter "reboot" at the prompt without quotes.
I would suggest the following procedure for erasing the drive before installing Snow Leopard:
Drive Preparation
1. Boot from your Snow Leopard Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
7. After the formatting has completed quit DU and return to the installer. Complete the OS X installation.

Why mac os 10.5.8 can not read snow leopard install dvd

why mac os 10.5.8 can not read snow leopard install dvd

Isit the white Snow Leopard Retail disc like the one here? http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard

Bought you Mac Mini from Amazon? Did it come with Snow Leopard installed?

I want to buy a Mac Mini from Amazon simply because it's cheaper and there's no tax, the question is, does it come with Snow Leopard like the one from Apple does?
I am not being a cheap @ss here, i lost my job and trying to save every penny i can.
Totals:
Amazon: $577.95
Apple w/student discount: $599.78
The 9.75% tax is killing us here in CA

Even if it does not come with Snow Leopard installed, or the upgrade drop in disk, you should still be able to get it for S&H from Apple thru the Up-to-Date program.
... If you’ve purchased a qualifying computer or Xserve on or after June 8, 2009 that does not include Mac OS X Snow Leopard, you can upgrade to Mac OS X Snow Leopard for $9.95.*
This program ends December 26, 2009. Your completed order form must be postmarked or faxed within 90 days of the date of your purchase of a qualifying computer or Xserve (described in this offer) or by December 26, 2009, whichever is earlier.
Also, you may want to look into Apple's refurbished Mac minis. They are usually a Mac that was DOA when shipped to a customer new and has been repaired by Apple. They are technically brand new and carry the same warranty. Occasionally they have surprises, like upgraded RAM.
Dah•veed

Problems with Booting from the Snow Leopard Install Disc

I need to do a reformat of my iMac drive and reinsall Snow Leopard. Then I want to run System Migration and move the contents of my Mac Pro (running Snow Leopard) over to the iMac.
I placed the retail Snow Leopard installation disc and held the "C" key down during restart. My optical drive make a bit of random noise and eventually ejects the SL disc. I've tried a CD, movie dvd and another software program installation disc and none of them seem to be able to be read. I've sold the Mac Pro and am in a bit of a bind as I need to get this done and shipped out. I'm also going to have to wipe the Mac Pro drives clean and do a reinstall of Snow Leopard.
Can anyone help?
Thanks,
John

Do you have the original install discs that came with the computer?
If you do, try powering up the mac pushing in the disc and hold the OPTION key, which will bring up the start up manager, select the insrall disc to boot from.
After booting, select the language, on the next page go to the menu bar and select Utilities/disk utilities, select your volume (default name is Macintosh HD, or what ever you ma have named it) First aid tab, run verify disk.
If it comes up with errors (they will be in red font) click repair disk. Rerun this till it it comes up with "this disk seems OK i(n green font)
Then quit the installer and eject the disk.
Try the Snow Leopard disk using the same proceedure (power up, push in disk, holding the OPTION key) to boot to the start up manager, and select the SL disk, and do a clean install.
Make sure that you have a retail install disk (white SL on it)
You can try this from the retail SL disc, if you do not have the Original disc(s) you should include all of them to the person you seel/give it to.
After install, follow these instructions.
http://www.thesafemac.com/how-to-prepare-your-mac-for-sale/
http://support.apple.com/kb/HT5189?viewlocale=en_US&locale=en_US
Hope this helps

How do I get Snow Leopard free Snow Leopard install DVD so I can upgrade to Lion and then be able to join the Cloud.

How do I get free Snow Leopard install DVD so I can then install LION and move to the Cloud?

Hi Robert,
If you are not a mobileme subscriber you will have to buy Snow Leopard install DVD. It is not free.
Good luck,
Alan

I used utilities to source my 10.6 snow leopard install disc to my main hardrive, and now when I turn on my computer the apple with the spinning wheel stays on the screen and stuck like that. How do I fix it Help please. I already tried all the commands

I used utilities to source my 10.6 snow leopard install disc to my main hardrive, and now when I turn on my computer the apple with the spinning wheel stays on the screen and stuck like that. How do I fix it Help please. I already tried all the commands such as Command R, Holding down the Option key, C and holding down shift at the start up but nothing happens.
initialy All I was trying to do was downgrade 10.7 to 10.6 .

You have to consider the possibility the hard drive may be dying. If your data isn't backed up, try one of the tools below:
https://discussions.apple.com/docs/DOC-1689
Once you are sure your data is backed up, we can examine other possibilities. In the meantime call AppleCare for your original installation DVDs. You may need them.

Is it possible to use the snow leopard install disk for bootcamp setup?

I'm going to be installing a windows 7 partition through bootcamp on my macbook, but I can no longer find the two original install disks that it came with. So my question was whether or not its possible to go through the bootcamp process with the snow leopard install disk?

Do you mean a "Retail OSX Snow Leopard Install DVD for USD 29" ?
If so, then yes. use it.
Sounds to me like the Original Install Discs you refer to are OSX 10.5 Leopard ones, right ?
These won't work with Windows 7 since Windows 7 requires OSX Snow Leopard DVD at minimum for the Driver Installation and BootCamp Assistant version 3.x as well, which is also only avaiable in OSX Snow Leopard.
http://support.apple.com/kb/HT1899
Stefan

HT1338 I have iMac 105.8 and want to upgrade to Snow Leopard, so got the disc from apple on line store and it will not install, just keeps ejecting from my desktop

I have iMac 105.8 and want to upgrade to Snow Leopard, so got the disc from apple on line store and it will not install, just keeps ejecting from my desktop

You have entirely too little free space on the boot drive, for best performance it's best to have hard drives only 50% filled max and never more than 80% filled.
See Storage Drive here and reduce some space also make a seperate bootable clone backup of all your data BEFORE upgrading
Most commonly used backup methods
see here for how to find your disk space
Why is my computer slow?
If you upgrade and it doesn't go right or slows the machine down you might need to erase and install, which all your programs will have to be reinstalled from original sources and files from backup.
How to erase and install Snow Leopard 10.6
If you can't do this, then hire a local PC/Mac specialist.
Do not upgrade to 10.7 or 10.8 on that older machine, it will slow down and you will lose all your PPC based programs.
Leave the Lions for a brand new machine with a SSD drive.

HT1386 I installed Snow Leopard and have the latest version of iTunes. However, when I connect my iPhone, it charges and iPhoto opens, but iTunes doesn't seem to recognize the iPhone. It simply doesn't appear in the left column. What gives?

I installed Snow Leopard and have the latest version of iTunes. However, when I connect my iPhone 4S, it charges and iPhoto opens, but iTunes doesn't seem to recognize the iPhone. It simply doesn't appear in the left column. What gives?

http://support.apple.com/kb/TS1591

Clean Snow Leopard Install yields the Welcome Video to loop continuously

Similar Messages

Maybe you are looking for