CleanAir Sensor Status: 'Down'

I have a problem about cleanair AP2602 down status show in Cisco Prime Infra and WLC cleanair operation status is "ERROR"
CleanAir Parameters
Operational Status
Reason
CleanAir Sensor is disabled due to irrecoverable error. AP reboot is required
now i solve the problem by reboot AP, but in several minute this problem is occure again. please help me for this problem.
Thank you very much.
WLC 7.3.112.0
and AP2602 software

I could be... I havent ran into that issue in the past with 7.3.x.  You might want to try upgrading to v7.4 and see if you still have those errors... But again, the errors are showing up on PI, so you need to see if the error is also being shown on the WLC or not as it can be an issue with PI.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Similar Messages

  • IDSM-2(5.0)inline mode- Pair Status=down??

    I have trouble with configuring idsm-2 inline mode(5.0).
    it seems that traffic doesn't go through idsm.
    I chechked it on command: sh interfac gi0/7(idsm mode)
    the 'pair Status=down'(below) shows that, i think.
    moreover, total packet received doesn't increase.
    how do i solve it?
    Please help!
    xxsystems# sh int gigabitEthernet0/7
    MAC statistics from interface GigabitEthernet0/7
    Media Type = backplane
    Missed Packet Percentage = 0
    Inline Mode = Paired with interface GigabitEthernet0/8
    Pair Status = Down
    Link Status = Up
    Link Speed = Auto_1000
    Link Duplex = Auto_Full
    Total Packets Received = 38
    Total Bytes Received = 2584
    Total Multicast Packets Received = 38
    Total Broadcast Packets Received = 0
    Total Jumbo Packets Received = 0
    Total Undersize Packets Received = 0
    Total Receive Errors = 0
    Total Receive FIFO Overruns = 0
    Total Packets Transmitted = 12
    Total Bytes Transmitted = 1152
    Total Multicast Packets Transmitted = 0
    Total Broadcast Packets Transmitted = 12
    Total Jumbo Packets Transmitted = 0
    Total Undersize Packets Transmitted = 0
    Total Transmit Errors = 0
    Total Transmit FIFO Overruns = 0

    You can only pair interfaces on your sensor if your sensor is capable of inline monitoring.
    http://www.cisco.com/en/US/products/sw/secursw/ps2113/products_installation_and_configuration_guide_chapter09186a00803eb069.html

  • Concurrent processing status down in OAM

    Hi ,
    From OAM->Applications Dashboard ->Overview
    the status for concurrent processing shows down but infact it is up
    I also checked from OAM->Hosts->view configuration
    whereas here the status for concurrent processing is up.
    thanks all in advance..
    applications version: 11.5.10.2

    Hi,
    Please see if these documents help.
    Note: 405375.1 - OAM Reports 'Internal Concurrent Manager Found Node To Be Down.' When Node is Up
    Note: 419823.1 - OAM: Web Components Status: Shows Down Even When The System Works Fine
    Note: 309271.1 - Web Components Status in OAM Shows All Down Even When the System Works Fine
    Note: 434569.1 - OAM application dashbord shows all the web components with status down whereas they are up
    Note: 287415.1 - Host Status In Application Dashboard Overview Tab Shown As Down in OAM
    Regards,
    Hussein

  • Active Protection 'abnormal sensor status'

    Hi, I'd really appreciate some help. I have just replaced my x61t hard disk (due to hd failure) with a WD Scorpio Black 320 gb.
    I installed Active Protection, and it worked OK for hours, but then suddenly it said that it was disabled because the 'system detected abnormal sensor status'. This has happened twice, and each time the laptop was sitting unattended on a table and wasn't moved at all!
    The notification recommended doing an AP test using PC Doctor for DOS, but this can only be run from a floppy drive, which I don't have right now. PC Doctor for Windows does not have an AP test function.
    I'm worried that this might be connected with the previous disk failure, though I did not get an AP error message then.
    Only one other person I can find has reported this error, but with no response from anyone.
    Can someone please help me? Is it possible the AP software conflicts with anti-shock protection already built in to the Scorpio? I don't want another disk crash!!!
    Many thanks,
    David (moderator note: email address removed- for user privacy)
    Message Edited by Agotthelf on 03-06-2009 12:17 PM

    I see thsi was posted some 9 months ago or something but almost exactly the same thing has just happned to me...
    Like you I cant run the PC Doctor DOS ( I mean WTF lenovo why not a bootable CD of this?) so I am just carrying on until i find a cure but the web site is silent on the issue...
    I am backing up religiously now ..but did anyone find an anser to this?
    Lenovo X200 Tablet / 350Gb HDD / 4GB RAM / Windows 7

  • SE3510 FC with ALERT "Voltage sensor status"

    Hi Experts,
    I have one SE3510 FC with Single Raid Controler connected to Sun V440 via HBA (DAS), the system has been working well at production for two years but suddently, Yesterday, SE3510 FC had Audible beep out continueously and I saw only Power/fan LED at Front-panel turned to brinking amber (All rear-panel LEDs of Power Supply Units lit with steady Green ).First step that i tried to test is to run sccli> show event that returning one line as below:
    "SES device on Sun Storage Array S/N#02E834 ALERT: CH2 ID2 Voltage sensor status is changed to critical (S9)".
    At my knowlege about this message, i supposed that there is one of power supply units is working improperly due to DC output supply unit ??.Or it's required to upgrade firmware for SES device (Existing SES Rev: 1040; Raid Controler's revison : 3.27R) to meet up with any changes related to FRUs( battery module replaced also) before ?.
    Pls help me to trouble-shoot this problem.
    Thanks
    Scott_land

    show enclosure-status command in sccli will show you status of componets in 3510
    look for records:
    PS 0
    PS 1
    and Voltage:
    info about sensor locations:
    http://docs.sun.com/source/816-7300-20/ch08_troubleshoot.html
    S9 - "sensor 9" belongs to "Lower I/O Module", so I'm not sure that the problem is with power supply ...
    Probably it worth to try "replug" Power supplies and RAID Controller.
    Alex

  • 1300 Bridge fa0 port status down

    I have a remote 1300 bridge whose fa0 port consistently goes down after working well for over a week. It shows the port as admin up but line status down - no carrier. It plugs directly into a 1200 ap. I have tried to hard code the speed and duplex but the option to hard code the speed is not available. Any ideas?

    Hi
    yes the console port on the power injector is is console port for the AP. probably the best way to recover the bridge is to connect the 1310 to a laptops etherernet port and use the console port to learn the IP of the 1310 then manage the 1310 with the GUI it can be done with the CLI but if you have not done a wireless bridge before stick with the GUI. Both 1310's need to be on the same subnet, this is for management not for bridging. the bridging is at level 2 unless you use VLANS but with the routers that should not be an issue. once you have configured the Root router save the config and use it to to congigure the non-root router changing the IP address and the role to Non Root. plug the network cables into the the apropriate router ports and you should be set.
    this is assuming you know the userid/passwords for the AP's  the default was Cisco/Cisco.
    if the antennas are alinged your bridge should be reliable.
    based on the signal level between the AP's i would disable the B data rates use the G data rates and possibley disable the higher data rates if the radio stats show to many retrys, mor than 10%.
    Bill

  • WIPS service status down

    Cant get my wIPS service running...
    Running 24 controllers( 4400s and wisms) , ver 6.0.188 using WCS ver 6.0.170  with 800+ 1140 access points
    Just installed an MSE 3310, WCS sees it and knows what it is.
    I cant seem to get the wIPS service to come up... status on WCS ( and MSE) is   "admin status enabled" .."operational  status down"
    Is there another step/trick to get it running ?
    Thanx

    Thanks Nael,
    MSE ver = 5.2.91
    WCS ver = 6.0.170
    stopped service via msed stop
    grep for any msed processes.... none shown
    started service via msed start
    echos back with the attached file output
    Starting MSE Platform
    Type: NAME Value: Chassis
    Type: DESCR Vlaue: Cisco 3310 Mobility Services Engine
    Type: PID Value: AIR-MSE-3310-K9
    Type: VID Vlaue: V01
    Type: SN Value: < removed>
    Starting MSE Platform, waiting to check the status
    Starting MSE Platform, waiting to check the status
    Starting MSE Platform, waiting to check the status
    MSE Platform is up, getting the status
    Unable to get MSE status.      Retrying status fetch -
    Unable to get MSE status.      Retrying status fetch -
    Unable to get MSE status.      Retrying status fetch -
    "getserverinfo" returns the same output

  • Cisco Wireless AP radio interface shutdown/Operation Status Down

    Hi,
    I am trying to troubleshoot the cause of the wireless AP 1142 radio shutdown; I was wondering where may be a good place to start on it/possibility of the radio shutting down. Once the radio is shown as down; I would just need to re-enable (disable/enable) it and the status changes to up status. I have attached a screen catpure of the radio interface showning down.
    The AP radios shutting down is intermittent; some APs has their "A/N" radio interface shutdown while others has their "G/N" radio interface shutdown. Not too sure what may most likely be causing it to shutdown?
    Any input is appreciated.
    Thanks.

    Do you have controller ?? if yes then posts out put of sh sysinfo commad.
    Paste the output of sh version command from AP.
    Also check: 
    1. Choose Wireless > 802.11a/n or 802.11b/g/n > Network
    Select the 802.11a (or 802.11b/g) Network Status check box to enable the 802.11a or 802.11b/g band.
    2. Wireless > Access Points > All APs then click on specific AP and make sure admin status is enable.
    Reagrds

  • Single Sign-On:orasso Status Down After Enabling SSL

    The status of Single Sign-On:orasso is listed as down in Enterprise Manager after enabling SSL. The same problem existed in with the Portal component, but this was fixed by adding a certificate to the certdb.txt file and by changing some URLs in the targets.xml file.
    Does anyone know how to correct this issue with Enterprise Manager? It has no effect on the behavior of our application, but it is causing problems with administration because some people use the Enterprise Manager console to monintor the state of our environment.

    Hi,
    Did U try this the following steps;
    When the configuration is finished, take the following steps:
    1.
    In the Application Server Control Console Confirmation page, click OK. The Application Server Home page appears.
    2.
    If you did not have an OC4J_SECURITY instance before, you will have one now. The OC4J_SECURITY instance will have a status of Down. You will also have a Single Sign-On:orasso instance with a status of Down. Select the check box next to OC4J_SECURITY and click Start.
    Note: You cannot start the Single Sign-On:orasso instance. This feature is started and stopped when you start and stop HTTP_Server and OC4J_SECURITY.
    3.
    When the operation completes, verify that OC4J_SECURITY has a status of Up.
    Note: The Single Sign-On:orasso status may be displayed as Down. This is normal. The status should be updated approximately five minutes after configuration.
    4.
    Select HTTP_Server and click Restart.
    5.
    Verify that you can access OracleAS Single Sign-On at the following URL:
    http://hostname.domain:port/pls/orasso
    In the URL, hostname.domain is the host on which OracleAS Single Sign-On is installed and port is the Infrastructure HTTP Server port.
    You can log in as orcladmin with the orcladmin password.
    Also try to check Oracle Application Server Single Sign-On Administrator's Guide
    Hear from U & regards,
    Hamdy

  • Portal status DOWN on EM but details show UP?

    Hi,
    I just installed 9iAS v2 (9.0.2.0.1) and used all default configuration. Infrastructure and mid_tier are installed on seperate unix box. Right after the installation all components are show status UP except unified message (down) and discoverer (? mark).
    After I made change to ORACLE_HOME/reports/conf/rwservelet.properties and rep_reports.conf files (following Note 210224.1) AND re started all on the mid_tier (follow note 200475.1), the status of portal:7777 on EM is DOWN, but the deails shows (click on the poratl link ) UP.
    other info on this detailed page are:
    left side:
    monitoring down
    database (on infrastructure) down (I can login scott/tiger@discodemo)
    on right side:
    mod_plsql_services down
    parallel_page_engine_services down
    syndication_server down
    Does anybody knows what these means and how can I fix it ?
    Thanks

    Happens all of the time. Bottom line is that the portal is up and running (assuming you can access it via /pls/portal). Oracle says this is due to underlying network issues, but I've seen this on every install I've done. I have noticed if you drill down further into the portal instance and then return to the main instance page, EM will show that it is up.
    Sure it is a bug...

  • 3702E-Operational Status DOWN

    Hi All,
    When we tried connecting ap, its registering to the WLC 5508 with version 7.6.120.0. But it shows operational status as DOWN in WLC and blinking in red,green continuously. If i admin disable it, then it is coming UP and instantly goes DOWN. 
    Any Suggestion.

    see whether you have correct country code configured on your WLC & connected AP is in the right regulatory domain.
    Wireless LAN Compliance Status
    Post the AP console output to see what's exactly happening.
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • Oper status down

    HI,
    I recently bought a Cisco 2504 Wireless Controller and a couple of access points (Cisco 1600 Series). Initially the controller had the 7.0.x.x firmware and from what i read on Cisco website it seems that this version is incompatible with my access points, so I updated the firmware on the controller to the latest version (7.4.110.0.). The access points were intially autonomous, so I installed the latest conversion to lightweight iOS image (ap1g2-rcvk9w8-tar.152-4.JA1). All work beautiful and I was happy until i discovered that after  the acces points succesfully join the controller the radio interfaces won't come up. On the controller i get the following messages:
    AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:7c:95:f3:6c:c6:30 Cause=Unknown Reset Status:NA
    AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:7c:95:f3:6c:c6:30 Cause=Unknown Reset Status:NA
    And here's what the acces point displays in logging mode:
    *Sep 27 06:35:01.169: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.10.10.1, mask 255.255.255.0, hostname APc08c.601f.260d
    Translating "CISCO-CAPWAP-CONTROLLER.xxx.local"...domain server (10.0.0.1) [OK]
    *Sep 27 06:35:03.605: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Sep 27 06:35:13.609: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Sep 27 06:35:02.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.10.10.5 peer_port: 5246
    *Sep 27 06:35:02.491: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.10.10.5 peer_port: 5246
    *Sep 27 06:35:02.491: %CAPWAP-5-SENDJOIN: sending Join Request to 10.10.10.5
    *Sep 27 06:35:02.495: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Sep 27 06:35:02.495: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Sep 27 06:35:02.495: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Sep 27 06:35:02.495: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.10.10.5
    *Sep 27 06:35:03.131: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Sep 27 06:35:03.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Sep 27 06:35:03.259: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller WLC_Intranet
    *Sep 27 06:35:03.311: ac_first_hop_mac - IP:10.10.10.5 Hop IP:10.10.10.5 IDB:BVI1
    *Sep 27 06:35:03.311: Setting AC first hop MAC: 4c00.8259.4ee0
    *Sep 27 06:35:03.311: ac_first_hop_mac - IP:10.10.10.5 Hop IP:10.10.10.5 IDB:BVI1
    *Sep 27 06:35:03.311: Setting AC first hop MAC: 4c00.8259.4ee0
    *Sep 27 06:35:03.683: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
    *Sep 27 06:35:04.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Sep 27 06:35:04.203: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    I must metion that all settings on the controller are fine (the access points interfaces are set to enable), but they just don't want to come up. I'm completely baffled by this problem and I don't know what to do next ? Can someone explain what's happeining ?
    PS: The access point are powered by their standard AC-DC power supply (not over PoE).

    Thanks for replies! One of the first thing that I did was to configure a NTP server, so the controller is time synchronized. Aslo I manually enable each radio interface.
    Here is the output for "show ap config 802.1b" (partial output):
    Cisco AP Identifier.............................. 14
    Cisco AP Name.................................... APc08c.601f.260d
    Country code..................................... RO  - Romania
    Regulatory Domain allowed by Country............. 802.11bg:-E     802.11a:-E
    AP Country code.................................. RO  - Romania
    AP Regulatory Domain............................. -E
    Switch Port Number .............................. 1
    MAC Address...................................... c0:8c:60:1f:26:0d
    IP Address Configuration......................... DHCP
    IP Address....................................... 10.10.10.7
    IP NetMask....................................... 255.255.255.0
    Gateway IP Addr.................................. 10.10.10.1
    NAT External IP Address.......................... None
    CAPWAP Path MTU.................................. 1485
    Telnet State..................................... Disabled
    Ssh State........................................ Disabled
    Cisco AP Location................................ default location
    Cisco AP Floor Label............................. 0
    Cisco AP Group Name.............................. default-group
    Primary Cisco Switch Name........................
    Primary Cisco Switch IP Address.................. Not Configured
    Secondary Cisco Switch Name......................
    Secondary Cisco Switch IP Address................ Not Configured
    Tertiary Cisco Switch Name.......................
    Tertiary Cisco Switch IP Address................. Not Configured
    Administrative State ............................ ADMIN_ENABLED
    Operation State ................................. REGISTERED
    Mirroring Mode .................................. Disabled
    AP Mode ......................................... Local
    Public Safety ................................... Disabled
    AP SubMode ...................................... Not Configured
    Remote AP Debug ................................. Disabled
    Logging trap severity level ..................... informational
    Logging syslog facility ......................... kern
    S/W  Version .................................... 7.4.110.0
    Boot  Version ................................... 15.2.2.0
    Mini IOS Version ................................ 7.5.1.73
    Stats Reporting Period .......................... 180
    Stats Collection Mode ........................... normal
    LED State........................................ Enabled
    PoE Pre-Standard Switch.......................... Enabled
    PoE Power Injector MAC Addr...................... Disabled
    Power Type/Mode.................................. Power injector / Normal mode
    Number Of Slots.................................. 2
    AP Model......................................... AIR-CAP1602E-E-K9
    AP Image......................................... C1600-K9W8-M
    IOS Version...................................... 15.2(2)JB2$
    Reset Button..................................... Enabled
    AP Serial Number................................. FGL1735X02L
    AP Certificate Type.............................. Manufacture Installed
    AP User Mode..................................... AUTOMATIC
    AP User Name..................................... Not Configured
    AP Dot1x User Mode............................... Not Configured
    AP Dot1x User Name............................... Not Configured
    Cisco AP system logging host..................... 255.255.255.255
    For the 802.11a interface things are almost the same.
    Output for show sysinfo:
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.4.110.0
    Bootloader Version............................... 1.0.16
    Field Recovery Image Version..................... 1.0.0
    Firmware Version................................. PIC 16.0
    Build Type....................................... DATA + WPS
    System Name...................................... WLC_Intranet
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
    IP Address....................................... 10.10.10.4
    Last Reset....................................... Software reset
    System Up Time................................... 3 days 5 hrs 33 mins 41 secs
    System Timezone Location.........................
    System Stats Realtime Interval................... 5
    System Stats Normal Interval..................... 180
    Output from "show time":
    Time............................................. Sun Sep 29 19:22:01 2013
    Timezone delta................................... 0:0
    Timezone location................................
    NTP Servers
        NTP Polling Interval.........................     3600
         Index     NTP Key Index     NTP Server      NTP Msg Auth Status
           1              0        x.x.x.x       AUTH DISABLED
    Output from "show verion" on one of the APs:
    Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(2)JB2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Mon 29-Jul-13 12:35 by prod_rel_team
    ROM: Bootstrap program is C1600 boot loader
    BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    APc08c.601f.260d uptime is 30 minutes
    System returned to ROM by power-on
    System image file is "flash:/ap1g2-k9w8-mx.152-2.JB2/ap1g2-k9w8-mx.152-2.JB2"
    Last reload reason:
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP1602E-E-K9    (PowerPC) processor (revision B0) with 98294K/32768K bytes of memory.
    Processor board ID FGL1735X02L
    PowerPC CPU at 533Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.4.110.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: C0:8C:60:1F:26:0D
    Part Number                          : 73-14508-04
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC17292D61
    Top Assembly Part Number             : 800-38553-01
    Top Assembly Serial Number           : FGL1735X02L
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-SAP1602E-E-K9
    Configuration register is 0xF
    Output from "show inventory " on one of the APs:
    NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
    PID: AIR-SAP1602E-E-K9 , VID: V01, SN: FGL1735X02L
    Output from "show inventory " on one of the APs:
    Interface                  IP-Address      OK?  Method  Status                Protocol
    BVI1                       10.10.10.7     YES  DHCP     up                    up
    Dot11Radio0                unassigned     NO  unset     administratively down    down
    Dot11Radio1                unassigned     NO  unset     administratively down    down
    GigabitEthernet0             unassigned     NO  unset     up                    up
    GigabitEthernet0.1           unassigned      YES  unset     up                    up

  • Why 12C Grid Control shows Target status down/Unavailable?

    Hello,
    The grid control 12.0.2 on Oracle Linux 5.9 shows that status of target /EMGC_GCDomain/GCDomain/EMGC_ADMINSERVER as down where as it is up and running and I can log into admin console.
    Please note that repository, OMS, weblogic all components are on same server.
    It is also showing that following are unreachable where as these are up on same server
    EM Website System
    Management Services and Repository
    How can I diagnose and fix this? Where to start?
    Thanks.

    Have you checked the agent status with emctl status agent? Is the OMS available there and when was the last upload time?
    You can also try emctl upload agent and see if this helps.
    Is the dbsnmp account unlocked with correct password in the target database?
    rgds
    Kjell

  • Status down

    i've just install OEL 5 and EBS 12.0 after completion of post install and apply the patch only HTTP componenet is Alive, how to make other comp alive? am i missing something.
    log
    02/02/12-06:00:38 :: adapcctl.sh version 120.6
    02/02/12-06:00:38 :: adapcctl.sh: checking status of OPMN managed OHS instance
    Processes in Instance: VIS_aq.aq.ebs.com
    ------------------------------------------------+---------
    ias-component | process-type | pid | status
    ------------------------------------------------+---------
    OC4J | oafm | N/A | Down
    OC4J | forms | N/A | Down
    OC4J | oacore | N/A | Down
    HTTP_Server | HTTP_Server | 3076 | Alive
    ASG | ASG | N/A | Down
    02/02/12-06:00:38 :: adapcctl.sh: exiting with status 0
    ================================================================================

    os
    Enterprise Linux Enterprise Linux Server release 5 (Carthage) i686
    app
    Oracle Applications Release 12.0
    02/02/12-12:11:22 :: adopmnctl.sh version 120.4
    02/02/12-12:11:22 :: adopmnctl.sh: Starting Oracle Process Manager (OPMN)
    opmnctl: opmn is already running.
    02/02/12-12:11:22 :: adopmnctl.sh: exiting with status 0
    Autocofig:
    while executing the statement adstpall.sh it shows following error in log file,_
    ERROR :
    Exception in TimedProcess...Failed to execute command = /u01/oracle/VIS/inst/apps/VIS_aq/admin/scripts/adopmnctl.sh stop -nopromptmsg
    [Service Control Execution Report]
    The report format is:
    <Service Group> <Service> <Script> <Status>
    Web Entry Point Services Oracle HTTP Server VIS_aq adapcctl.sh Failed
    Web Application Services OACORE OC4J Instance VIS_aq adoacorectl.sh Failed
    Web Application Services FORMS OC4J Instance VIS_aq adformsctl.sh Failed
    Web Application Services OAFM OC4J Instance VIS_aq adoafmctl.sh Failed
    Batch Processing Services OracleTNSListenerAPPS_VIS_aq adalnctl.sh Failed
    Batch Processing Services OracleConcMgrVIS_aq adcmctl.sh Failed
    Batch Processing Services Oracle ICSM VIS_aq ieoicsm.sh Disabled
    Batch Processing Services Oracle Fulfillment Server VIS_aq jtffmctl.sh Failed
    Other Service Group Disabled
    Other Service Group OracleFormsServer-Forms VIS_aq adformsrvctl.sh Disabled
    Other Service Group Oracle Metrics Client VIS_aq adfmcctl.sh Disabled
    Other Service Group Oracle Metrics Server VIS_aq adfmsctl.sh Disabled
    Other Service Group Oracle MWA Service VIS_aq mwactlwrpr.sh Disabled
    Root Service Group Oracle Process Manager for VIS_aq adopmnctl.sh Failed
    ServiceControl is exiting with status 8
    while executing the following stat adstrtal.sh it give following error in log file
    ERROR :
    Exception in TimedProcess...Failed to execute command = /u01/oracle/VIS/inst/apps/VIS_aq/admin/scripts/jtffmctl.sh start -nopromptmsg
    Service Group Other Service Group is disabled.
    [Service Control Execution Report]
    The report format is:
    <Service Group> <Service> <Script> <Status>
    Root Service Group Oracle Process Manager for VIS_aq adopmnctl.sh Failed
    Web Entry Point Services Oracle HTTP Server VIS_aq adapcctl.sh Failed
    Web Application Services OACORE OC4J Instance VIS_aq adoacorectl.sh Failed
    Web Application Services FORMS OC4J Instance VIS_aq adformsctl.sh Failed
    Web Application Services OAFM OC4J Instance VIS_aq adoafmctl.sh Failed
    Batch Processing Services OracleTNSListenerAPPS_VIS_aq adalnctl.sh Failed
    Batch Processing Services OracleConcMgrVIS_aq adcmctl.sh Failed
    Batch Processing Services Oracle ICSM VIS_aq ieoicsm.sh Disabled
    Batch Processing Services Oracle Fulfillment Server VIS_aq jtffmctl.sh Failed
    Other Service Group Disabled
    Other Service Group OracleFormsServer-Forms VIS_aq adformsrvctl.sh Disabled
    Other Service Group Oracle Metrics Client VIS_aq adfmcctl.sh Disabled
    Other Service Group Oracle Metrics Server VIS_aq adfmsctl.sh Disabled
    Other Service Group Oracle MWA Service VIS_aq mwactlwrpr.sh Disabled
    ServiceControl is exiting with status 8

  • Status Down for DB target

    Hello, please i need some help.
    The status for a DB target is shown as Down in the Enterprise Manager Grid Control console. However, the DB is up and is working normally. What i can see is that user Dbsnmp is Locked(Timed) in dba_users, could this be the problem?. What users are involved with agents and conections to grid control?
    How can i refresh the status?
    Thanks in advance.

    The user that OEM uses is determined by the configuration step with the agent in OEM. So click on the agent in OEM, click the radio button for the db, click configure. Give it the dbsnmp userid and credentials.

Maybe you are looking for