Clearing Statistics on MDS-9509

Can anyone tell me how to clear the statistics (errors, discards, etc.) from the Device Manager GUI for a single port or group of ports?

It is pretty easy.
Open your device manager.
Choose the following menu options
Interface
Monitor
FC Enabled (or fcip, or ethernet)
A window will pop up with the port statistics.
You can Click on the eraser looking button to clear the cumulative counters of the ports you are looking out.
The other option is to log onto the switch, and issue the clear counters interface fc1/x command.
If this was usefully please rate it :)
--Colin

Similar Messages

  • SNMP OID for CPU and Memory Utilization on a MDS 9509

    Does anyone know what the OIDs are for CPU and Memory utilization on a MDS 9509?
    Thanks

    CISCO-SYSTEM-EXT-MIB.my is a good place to start and you can determine the OID from the MIB.
    Once you feel as though you are on the right track, have a look at:
    http://www.oidview.com/mibs/9/CISCO-SYSTEM-EXT-MIB.html
    I gather that what you need is:
    1.3.6.1.4.1.9.9.305.1.1.1
    and
    1.3.6.1.4.1.9.9.305.1.1.2
    Enjoy.
    Stephen

  • How to install software on MDS 9509 Switch

    Hi,
    One of our MDS 9509 switches has died. This used to be supported externally but has now been brought in house. A replacement box is due to arrive soon but I will nee to update the software to the same version that the old box was using and apply the config.
    What procedure should I follow to do this? I've downloaded the following kickstart and image files ready to ftp across to the new box.
    m9200-ek9-kickstart-mz.3.3.5a.bin m9200-ek9-kickstart-mz.3.3.5a.bin
    is it simply a case of running the install all command?
    Thanks
    Darren

    Also you will need to install license same as on old and restore config. Hope you had config backup somewhere. Additionally you will have to update port security schemes (if configured). Once all done, look for any zone merging errors or conflicts.
    Good luck,
    Nisar
    Sent from Cisco Technical Support iPad App

  • Migrating from Brocade 2800/ 3900 to Cisco MDS 9509

    What is the best procedure from migrating from Brocade 2800/3900/12000 to Cisco MDS 9509 especially connected to HP-UX and AIX server.
    Without any Downtime I should be able to migrate these servers.
    I thought about these options:
    1. Use vgexport and vgimport or exportvg and importvg (AIX) after connecting to Cisco MDS. But this requires complete downtime on the application.
    2. Take one path down or HBA down and switch the cable and vgextend the devices.
    Please let me know if somebody has procedure.
    I was successful in HP-UX server using the second options but I cant see all the LUNs. That might be array specific problem also.
    If anybody has detailed procedure on migrating this scenario. please let me know.
    We are using Persistent FCIDs on our MDS switches.
    Thanks in Advance

    After connecting 1 cable from server HBA to Cisco S/w, why you are not able to see all LUNs, did you cross-check that...I mean HBA Configuration (max 256 LUNs) or Disk Array library driver to be installed on host side.if that can be sorted out, you can mirror the volumes across the disk arrays.are you using HDS Arrays? I don't know but what is vgextend command you are mentioning...
    also did you take a reboot of server or is it online addition on new LUNs...
    Also any how if you are not able to see all LUNs that is going to be an issue later as well for migration...pls cross-check that...

  • Cisco MDS 9509 and HP Blade server problem

    I have a big problem , when i connected to MDS 9509 to HP VC-FC 8GB the module in MDS 9509 did not detect the HP module . I think this will be because MDS 9509 uses VSAN technology , but HP blade is not support this feature. Please help me

    I am fairly certain that the HP blade chassis has HP branded Brocade FC switches. These switches need to be placed into AG mode and rebooted. On the Cisco MDS core the NPIV feature must be enabled.
    Here is more info on the Brocade AG mode -
    http://www.brocade.com/solutions-technology/technology/platforms/fabric-os/access_gateway.page
    http://www.brocade.com/downloads/documents/data_sheets/product_data_sheets/AccessGateway_DS_02.pdf
    Cisco NPIV info
    http://www.cisco.com/en/US/prod/collateral/ps4159/ps6409/ps5989/ps9898/white_paper_c11-459263.html

  • MDS 9509 - Mgmt Interface alerts

    I am seeing the following entries in the logs for my MDS 9509 :
    2007 Feb 7 01:48:03 PORT 5 IF_UP Interface mgmt0 on slot 5 is up
    There are no other entries in the log that the mgmt0 interface went down so why would alerts say that it is "up" ?

    Looks like the mgmt interface has been bouncing up & down since Sept. What is this attached to? What does that log say? Is the duplex and speed the same on both sides? Can you replace the cable? Does the show interface mgmt 0 show increasing CRC and/or output errors? These are the things to look for. Try a new cable as it's the easiest and most probable issue.

  • ISL Ports (E ports) on MDS 9509 are showing Gracefully Shutdown

    We have an ISL connection between E mode ports of two MDS 9509 Switches . (FabricA)
    Upon Health Check I found that these ISL ports on both the switches are down and when I checked syslogs on both switches they show "Interface X/X Gracefully shutdown"
    I checked the Cisco document for this error which says -
    "The Cisco NX-OS software implicitly performs a graceful shutdown in response to either of the following actions for interfaces operating in the E port mode:
    If you shut down an interface.
    If a Cisco NX-OS software application executes a port shutdown as part of its function."
    So no one has shut down these ports manually  and I am not sure what the second point (If a Cisco NX-OS software application executes a port shutdown as part of its function) means
    I tried shut / no shut on these ports bt no go.
    I need to know what could be the problem and its resolution.

    Hi Vishwa,
    Sounds like there is a problem between switches.  Look at a "show interface" and see if it is "error disabled".  I don't know the topology, maybe optical equipment or patch panel between switches?  You can look at the signal levels on the interfaces with "show interface fcx/x after the no shut.  The signal levels are not valid if the interface is not "in sync" but you can still get an idea of no receive signal.  Do a "not shut" on both sides and look at the levels.   Look for other messages in the logs at the same time and post those here.
    Best regards,
    Jim

  • Interop problem between brocade 300d/200e and MDS 9509

    Hi, I want to know if  mds 9509 can interop with the SAN equipment below.
    If yes, can you help me to configure (VSAN and type of ports - TE or T or F).
    I tried with the interop VSAN 1 and 3, but there is still no communication.
    MDS 9509
    kickstart: version 5.2(2d)
    system:    version 5.2(2d)
    and
    Brocade 200E or 300D
    V6.1.0J

    You want Cisco MDS to be the principal switch, this is all explained in the FC standards.
    The switch with the lowest wwn becomes the principal switch if the domain priorities set the same.
    It is all explained in MDS config guide:
    http://www.cisco.com/en/US/products/ps5989/products_configuration_guide_chapter09186a0080664c6a.html
    http://www.cisco.com/en/US/products/ps5989/products_configuration_guide_chapter09186a0080664cd1.html#wp1185238

  • Get user public key (ssh) from MDS 9509

    how can get public key from a user on MDS 9509?

    I'm not sure exactly what you are looking for, but to create keys for SSH, you will want to enable SSH like this:
    ssh server enable
    Then, you can generate a key like this:
    ssh key
    Or to specify the key for a user, it would be like this from the CLI:
    username ssh

  • Firmware info for MDS 9509

    Requesting latest firmware info for Cisco MDS 9509 switches.

    Hello,
    The following link will take you to the download section for MDS Firmware:
    http://www.cisco.com/kobayashi/sw-center/sw-stornet.shtml
    You would need to login using CCO username/password.
    Hope this helps.
    Regards,
    Nikhil

  • MDS 9509 Stencils and Sample Diagrams

    Hi,
    Need some stencils and possibly existng sample-type diagrams for a medium sized deployment of two MDS 9509 core switches. Two seperate Fabrics for redundancy in the diagrams would help too.

    Please download the VISIO stencils for the MDS products from the link below:
    http://www.cisco.com/en/US/prod/assets/visio/product_visio_icon0900aecd800d1dc0.zip

  • MDS 9509 Memory

    Can someone confirm for me whether or not the MDS 9509 supports a memory upgrade?

    G'day,
    Are you having issues that requires an upgrade? :)
    You could prob upgrade it but its not somthing that you can buy a upgrade kit for... :)
    And... you prob wouldn't be supported.
    To be sure you might want to check your local SE

  • MDS 9509 HTTP

    How to you disable HTTP on a MDS 9509?

    You can't. If your worried you can apply an access-list to the mgmt 0 interface to restrict who can access your MDS.

  • Best Design practices of SAN with the MDS 9513,MDS 9509 and Brocade 8510

    Hi
          Am searching best design to implement CISCO MDS 9513,9509, Brocade 8510,Storage and UCS all clubbed in the topology. And please suggest me any tool to compare MDS and Brocade 8510 performance.

    Boomi,
    Both MDS and Brocade will serve basic features of Storage networking. Both can be mix and match to achieve redundancy, which you already have. However, if you are looking for any tool or perfmon then there isn't much to compare. You can use IOmeter or Akkori. I see that you have enterprise level hardware in your setup. Not sure what other line cards you have installed and what application are running through, and if you have remote sites (SAN islands) then the real difference of features and best practices can be discussed. For example, IVR, FCIP, ISCSI, FCoE, etc.
    Thanks,
    Nisar
    Sent from Cisco Technical Support iPad App

  • 10 gig iSCSI port in MDS 9509

    Hi all,
    I have a requirement of 128 port SAN switch (Director class)
    -          15 ports should be iSCSI 10g
    -          Rest 113 port should be 8 Gbps FC
          I am planning to go with two DS-X9248-96K9 module and one DS-X9224-96K9 to meet 120 ports.But I didnt find any 10 gig iSCSI port which is suported in 9509/9506 chassis. Can you please suggest? I can see only GE modules like DS-X9316-SSNK9.
          Also please suggest whether we get line speed in 48-Port 8-Gbps  Fibre Channel Switching Modules?
    Thanks in advance,
          Raghavendra

    Correct...the key is that the 48 port line card has the 96 in the p/n.  That indicates is it a performance module and has the 6 port groups.  There is also what is called a 48 port 8 gig host optimized line card.  That one only has 4 groups of 12, in which 1 of those (4 total) can operate in 8gig mode.
    The 24 port line card has 8 groups of 3 port...and 1 of those (8 total) can operate in 8 gig mode.
    As for the 10 gig iSCSI ports on the MDS...that will probaly not be a feature that the MDS will ever adopt.  The MDS is an iSCSI gateway, where by iSCSI initiator can access a native FC target.  With the advent of more and more natice iSCSI targets, and the move to 10GE, the Nexus 5K is the swtich to use.  It can host iSCSI targets and initiators and provide 10GE for both.  The MDS is not a 10GE switch.
    -hope this helps,
    Mike

Maybe you are looking for

  • Drag & Drop ViewObject as Table Exception

    Hi, When I drag & drop any view object onto the page, there are no problems when dropping it as a Form. When I drag & drop the same view object onto the page as a Table, however, a stack trace appears from JDeveloper. I have posted screen shots showi

  • MEDIUM ERROR Burning a DVD-R

    Hi, I'm trying to burn a DVD for several times with Roxio Toast Titanium 6. I used to do it like this always but now it seems impossible. I'm trying to record a DATA DVD and this is the error I get: The drive reported and error: Sense Key = MEDIUM ER

  • Drop Shadow Effect Cannot Be Seen

    I'm using CS4 for Windows and I own several great books for it, yet I'm still struggling completing a simple drop shadow effect on a photo. No matter what I try from using the simple drop shadow fx or complex suggestions building several different la

  • Commcli problem

    Hello, trying to use commcli to list users, modify domain, anything, it fails with the following message when running in debug mode: [Debug]: RECV: FAIL [Debug]: RECV: com.sun.identity.authentication.spi.AuthLoginException: Failed to create new Authe

  • HT4682 using fcp 7 with sony vg-20

    I purchased a Sony camcorder VG-20 and I thought it would have give no problems at all with fcp, it looks like it doesn't work. Does anybody know a way out? Not selling the camcorder :-) Thx