Clearing wireless statistics

On Cisco 1242 AP you can "sh dot11 associations all-client | include Address | Bytes" and this will give you a list of all associated clients and how much data they have transferred. Other than rebooting the AP is there a way to clear those stats so you can monitor from a fresh start?

i agree that will clear the stats for 1 associated client. using a * instead of does not clear all. Clearing the stats on all 23 associated clients is the desired outcome.
Thanks

Similar Messages

I just got clear wireless service and cannot use firefox. how do i fix this

hi,
i have dial up. just got clear wireless. if i use the dial up i can use firefox, no problem. i have the latest firefox. if i use clear i can only get a couple of websites. can some help me. not to computer savvy. i need step by step info.
thank you
bonnie

Reload web page(s) and bypass the cache to refresh possibly outdated or corrupted files.
*Press and hold Shift and left-click the Reload button.
*Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
*Press "Command + Shift + R" (MAC)
*http://kb.mozillazine.org/Error_loading_websites

Airport Express Conflicts with Clear Wireless Network?

After months of stumbling around, trying to figure out why my Clear Wireless internet service was so choppy, I finally plugged the ethernet cable directly into my computer, and disabled my local Airport network. Voila! Works like a charm -- very fast and reliable, now. Trouble is, I don't have network access for my laptop. The problem (I suspect) is that I also have phone service on my Clear modem.
Here's what the connection looked like (and was recommended by Clear Wireless), with <-> meaning wireless connection and <+> meaning an ethernet connection:
computer(s) <-> Airport Express <+> Linksys Phone Box <+> Clear Modem <-> Clear Tower
So, pulling the Airport Express out of this sequence cleared up ALL of the stalling problems and slowness. My new (and functioning) set up looks like this:
computer <+> Linksys Phone Box <+> Clear Modem <-> Clear Tower
My question is whether I can have somehow connect the Airport Express on the other side of my computer, and allow my local network access the Clear Wireless modem via my computer? Right now, I've got the Airport Express plugged in and running, mostly to check if there was simply an interference problem, and that doesn't seem to be the case (the phone connection is a base station with wireless handsets, so thought there might be interference there -- doesn't seem to have been an issue).
Any advice on this would be great. Clear Wireless is as clueless on technical support as it is brilliant in concept. Still very much in startup mode, with phone operators reading from generic scripts and masses of angry users spamming their discussion board -- ugh! Thus my post here. I'd love to see a schematic that shows the optimal way to bring a phone connection into a local wifi network.
Thanks!

What I would like to do is to connect the airport express to the wireless network (Linksys-router).
What are you trying to do with the AirPort Express Base Station (AX)? Use it for streaming iTunes and/or share a USB printer, or extend your existing Linksys wireless network?

WLC2006 - How to clear client statistics

Hi,
I have a few questions about the WLC2006 CLI:
1 - Client statistics can be displayed on the WLC2006 with the command "show client detail <MAC addr>". I don't find in the documentation how to clear these statistics.
2 - Comments are generally welcome in capture files. What is the "!" IOS equivalent?
3 - Is it possible to suppress the "more" with a command such as "terminal length 0"?
Any link is welcome. Thanks by advance.
Best Regards,
Alain-Claude

The show client detail command output depends on the clients that are presently associated with the LAP. Once the clients get disconnected from the network, the stats should get cleared automatically.
We presently do not have a equivalent command for terminal length 0.

Clear Wireless Modem not communicating with Time Capsule

I have a clear wireless home modem and am having connection issues with my time capsule. Has anyone else had this problem? How did you resolve it? I know the modem is working because when I connect the ethernet directly into my computer it works. Help!?

Is this a new TC?
Most important.. did you power cycle the modem. If this is a cable network pure modem ie no router function.. did you power down the modem for say 20min at least?? Then power up modem wait a couple of min for it to stabilize then power up the TC.
If the TC is bridged this is not necessary.. ie your cable modem is also a router.
Here is a bit of detail about checking the wireless is ok.. but IMHO the likely issue is not wireless per se.
Did you use identical wireless names? If so try deleting all the old names in the computer under the wifi network preferences.
Select each one and use the minus to delete it.
Then redo the configuration for the TC.
No luck start over .. factory reset the TC use all new names.. short, no spaces and pure alphanumeric will give you much less problems in the future.
Still no luck make sure you have ipv6 set correctly.. ie link local only and check the gateway (router in applespeak) and dns values are correct.. dns is not on the main page.. it has a separate tab.

Clear Connection statistics WAE

How do we clear connection stats in monitoring option in WAE ? I went to CLI and run "clear statis all" but could not clear "connection summary table" in "monitoring" display.
thanks
Serhat

I don't think this connection summary screen is reflecting what has been happening. I have disconnected the link (all sessions broken), it still shows connections that started 11 and 6 hours ago.Besides, I am running Netflow in the branch router that shows 64 MB of Notes traffic sent to the branch but connection summary does not have any stats on it. I might report this to TAC.
10.64.191.40:2358 10.64.101.151:42510 waasdcp1 11:19:13 36.5117 KB 22.623 KB 38%
10.64.191.15:32873 10.64.101.151:27010 waasdcp1 6:45:20 28.2832 KB 9.5088 KB 66%
10.64.241.130:2418 10.64.191.21:445 waasdcp1 0:30:17 19.1846 KB 12.1631 KB 37%
10.64.218.91:1602 10.64.191.21:445 waasdcp1 0:21:14 13.6436 KB 8.0693 KB 41%
10.64.102.76:1927 10.64.191.21:445 waasdcp1 0:21:1 26.7871 KB 16.7832 KB 37%
10.64.241.105:2145 10.64.191.21:445 waasdcp1 0:14:22 8.8232 KB 7.4648 KB 15%

Clearing Global IKEv1 Statistics

All,
I would like to clear the statistics for when I type "sh isakmp stats". Below is the output when I type the preceding command. I would like that cleared for testing.
Global IKE Statistics
Active Tunnels: 1
Previous Tunnels: 221
In Octets: 2811534
In Packets: 7545
In Drop Packets: 3954
In Notifys: 2396
In P2 Exchanges: 263
In P2 Exchange Invalids: 0
In P2 Exchange Rejects: 1
In P2 Sa Delete Requests: 111
Out Octets: 747448
Out Packets: 7830
Out Drop Packets: 0
Out Notifys: 8506
Out P2 Exchanges: 0
Out P2 Exchange Invalids: 0
Out P2 Exchange Rejects: 0
Out P2 Sa Delete Requests: 109
Initiator Tunnels: 3
Initiator Fails: 3
Responder Fails: 112
System Capacity Fails: 0
Auth Fails: 66
Decrypt Fails: 0
Hash Valid Fails: 0
No Sa Fails: 396

There was no command to reset those Run/Pass number unless reload the module

How to clear "show summary" service hit statistics on CSS11500?

Sounds simple but I'm unable to locate the command to clear these statistics other than a reboot.
We are testing the CSS 11500 and trying to determine the hit counts. Clearing these statistics would be very helpful.
Help is much appreciated! Regards

Hi Kenneth,
You can clear the counters by going into the owner prompt and give command "zero all"
css(owner[tanveer])#zero all
Tanveer

Clearing Statistics on MDS-9509

Can anyone tell me how to clear the statistics (errors, discards, etc.) from the Device Manager GUI for a single port or group of ports?

It is pretty easy.
Open your device manager.
Choose the following menu options
Interface
Monitor
FC Enabled (or fcip, or ethernet)
A window will pop up with the port statistics.
You can Click on the eraser looking button to clear the cumulative counters of the ports you are looking out.
The other option is to log onto the switch, and issue the clear counters interface fc1/x command.
If this was usefully please rate it :)
--Colin

I can no longer get into my WRT150N1.1 router any longer since I switched to Clear

I switched to Clear wireless a few weeks ago and I can no longer get into my router to change the settings. This is a bummer because I now no longer have a secure connection. 192.168.1.1 no longer accesses the router, and I checked my IP address and it is (for clear I assume) 192.168.15.3. So I tried using 192.168.15.1 and it took me to Motorola WIMX CPE, (which I am assuming is the Clear webpage)
I am on a Mac running Intel chip. Any help would be appreciated.
Have tried getting in from my Ipad without any luck.
Thanks

The trick to make this work is
hold down the reset button for about 30 seconds, then unplug the device, while you are still holding down the reset button.
leave unplugged for about 5 seconds, while you are still holding down the reset button.
plug the unit back in, while you are still holding down the reset button.
after about 5 seconds, let go off the reset button.
go to the webpage of the router.
Now you can try to access the setup page of your Router, i think this should work and you should be able to access the setup page of your router and able to make the changes on your Router.

Can i use apple tv on clear spot wifi network?

I am using clearwire spot wifi device to share internet. Can i use apple tv on the dvice and stream ipad video on the tv thru airplay?

I have a clear wireless modem and it works perfectly.

ASA 5520 v7.2 - VPN site to site problem and clear command

Hi all,
I am getting some problems with a Site to Site VPN from the last two weeks. In some occasions it stops to send traffic through the VPN without any apparent reason. I have other VPNs that continue working fine. While it is failing I have run the command "show crypto isakmp sa" and I have found that I have two entries for the peer that is failing:
9 IKE Peer: x.x.x.x
Type: L2L Role: responder
Rekey: no State: AM_REKEY_DONE_H2
10 IKE Peer: x.x.x.x
Type: L2L Role: initiator
Rekey: yes State: MM_ACTIVE_REKEY
Any idea about what is happening?
On the other hand at the moment the only way to solve this has been using the command "clear crypto isakmp sa" but the problem is that this command clear all the entries and I lose the connectivity in all the other tunnels until the are established again. Is there any way to clear only the tunnel that has problems?
Regards, Fernando.

Hi MD,
I have tried to use the command that you said but that option doesn't appear in my ASA.
asa# clear crypto ?
accelerator Clear accelerator statistics
ca Certification authority
ipsec Clear IPsec operational data
isakmp Clear ISAKMP operational data
protocol Clear protocol statistics
asa(config)# clear crypto ?
exec mode commands/options:
accelerator Clear accelerator statistics
ca Certification authority
ipsec Clear IPsec operational data
isakmp Clear ISAKMP operational data
protocol Clear protocol statistics
Do you know any other possibility?
On the other hand, do you know why I am having this issue?
Regards, Fernando.

Prefix-list; clear bgp peer-group Test soft in; no file prompt quiet

Hello everyone,
I have a few simple questions. Hope someone will help me Thank you in advance.
1) We are using prefix-set into route-maps, but how I can use a prefix-list?
2) In classic IOS we have the command: clear bgp peer-group Test soft in
I don't see it in IOS-XR (Cisco IOS XR Software, Version 4.0.1):
RP/0/RSP0/CPU0:STH02#clear bgp ipv4 unicast ?
*                  Clear all peers and all routes from the BGP table
A.B.C.D or X:X::X BGP neighbor address to clear
as                 Clear peers in a specific AS
dampening          Clear route flap dampening information
external           Clear all external peers
flap-statistics    Clear flap statistics
nexthop            Clear nexthop
self-originated    Clear redistributed, network and aggregate routes originated here
shutdown           Clear all peers which were shut down due to low memory
3) In classic IOS we have the command: no file prompt quiet
I don't see it in IOS-XR. What is the command for IOS-XR?
I need it for the operation like this:
copy ftp://**:***@216.*.*.*/CUST_AS-TEST-in.prefixlist compactflash:/PrefixFilters/CUST_AS-TEST-in.prefixlist
Wed Apr 18 12:02:00.936 UTC
Destination filename [/compactflash:/PrefixFilters/CUST_AS-TEST-in.prefixlist]? !!!!   I don't need this question
Copy : Destination exists, overwrite ?[confirm]                                                   !!!!   I don't need this question
Accessing ftp://*:*@216.*.*.*/CUST_AS-TEST-in.prefixlist
C
584 bytes copied in      0 sec
Have a nice day,
Dimitry

Thank you Alexander for your reply. It is the good RPL description and I've got the idea of REFRESH capable peer.
BUT, I still don't find the answer on my 3-d question:
In classic IOS we have the command: no file prompt quiet
I don't see it in IOS-XR. What is the command for IOS-XR?
I need it for the operation like this:
copy ftp://**:***@216.*.*.*/CUST_AS-TEST-in.prefixlist compactflash:/PrefixFilters/CUST_AS-TEST-in.prefixlist
Wed Apr 18 12:02:00.936 UTC
Destination filename [/compactflash:/PrefixFilters/CUST_AS-TEST-in.prefixlist]? !!!!   I don't need this question
Copy : Destination exists, overwrite ?[confirm]                                                   !!!!   I don't need this question
Accessing ftp://*:*@216.*.*.*/CUST_AS-TEST-in.prefixlist
C
584 bytes copied in      0 sec
How can I suppress confirmations like this?
Destination filename [/compactflash:/PrefixFilters/CUST_AS-TEST-in.prefixlist]?
Copy : Destination exists, overwrite ?[confirm]
Dimitry

My Aluminum Wireless Keyboard Thinks it's a Mouse!

I'm having troubles with my aluminum wireless keyboard. When I first got it I paired it with my MacPro1,1 and it worked great for a couple of months, then it all of a sudden stopped working (no, I didn't drop it). I went back to using my old white/clear wireless keyboard and that one works perfectly.
I have tried pairing the aluminum keyboard numerous times to no avail. I will explain to you what happens. After deleting the keyboard from bluetooth, I pair it again. The aluminum keyboard appears on the list and I click it to pair it. It asks me to type in a code, which I do (from the aluminum board, not the white one). I hit return and wait a few seconds and it tells me pairing was successful.
When I go to use the newly paired keyboard, it will not type. What I DO get is mouse curser movement from various keys. Holding down the letter "O" moves the curser to the right, "U" moves it left, "8" moves it up, and so-forth.
I took the keyboard in to the Apple store to get an exchange. They tested it and showed me how it works perfectly on their computers. They suggested I update my OS to the latest version along with all related firmware and try it again. So, I just installed snow leopard 10.6.1, and tried repeatedly to pair the keyboard again to no avail. It is still doing the exact same thing! I am running the latest wireless keyboard firmware, it has new batteries, I removed and replaced the batteries several times and it just does not help. I am stumped!
I love my aluminum keyboard and desperately want to use it. Any ideas on how I might correct this problem? Thanks for your time!

Hiya opalmic,
have you tried a PRAM reset: http://support.apple.com/kb/HT1379
and secondly, do you need to install a bluetooth firmware update 2.0.1? :
http://www.apple.com/support/bluetooth/
finally, you could open up keychain first aid and repair it.
Please advise if that resolves your problems?

Local Director Clear Stats

I've got a LD416 running 3.1.4. I need to clear the statistics on it to help examine a problem. Is there any way to do this in 3.1.4? I've been going through the docs and maybe I'm blind but it doesn't seem to an option???
Thanks
-Paul Gomez

unfortunately there is no way - except the reload.
Gilles.

Clearing wireless statistics

Similar Messages

Maybe you are looking for