Client IP Address issues

Just starting to put a Cisco Wireless infrastructure in place, currently just testing every thing. Here is my issue.
After I create a WLAN, bind it to the VLAN I can authenticate but can't get an IP address.
Now if I bind the WLAN to the same VLAN the AP is on, I can get an IP address.
I do have the DHCP IP configured under WLAN as well as interface, I tried it with just configuring it on the interface but no use
I tried DHCP proxy enabled and disabled
Also want to mention that the AP is connected to a switch and the switch port is setup as an access port on VLAN130.

what happens if we assign static Ip address?? are we able t oping the Default Gateway?? or from the DG are we able to ping the client??
Normally the LWAPP in local mode will be in the Access Port.. not trunk... so if you assign vlan 130 on the switch port then the clients connecting to VLAN 109 should also get the IP since its LWAPP tunneled.. So from my understanding.. you are configuring VLAN 130 on the switch and connecting the AP and the VLAN 109 guys are not getting the IP where in VLAN 130 guys are getting the IP?? please correct me if my understandings are incorrect..
>> in this case.. i have a question.. To what switch is this AP connected to?? any small business switch like CE 500 or anything better than that?? like 2960 and so on..??
>> Are we able to ping the Default gateway from the WLC and the Client (the interface VLAN which is facing the issue )??
>> check the switch port configuration on which the WLC is connected and make sure the problematic VLAN is allowed.. or on the switch check if we have that VLAN in the VLAN.dat allowed.
Lemme know how this works out for you!!
Regards
Surendra

Similar Messages

Install PT8.53 with Linux Issue: Jolt client (ip address 192.168.196.102) does not have proper application password

Folks,
Hello.
I am installing PeopleTools 8.53 with Oracle Database Server 11gR1 and OS Oracle Linux 5.10.
Data Mover Bootstrap and Application Designer can log into Database instance successfully. My procedure to run PIA is below:
Step 1: start Oracle Database Server and LISTENR is listening.
Step 2: start Application Server ./psadmin and 8 processes are started.
Step 3: start WebLogic Server PIA /opt/PT8.53/webserv/PT853/bin/startPIA.sh
In Browser, http://192.168.196.102:8000/ps/signon.html comes up successfully. But when sign in using UserID PSADMIN and password "myname", I get the error message in Browser as below:
The application server is down at this time.
CHECK APPSERVER LOGS. THE SITE BOOTED WITH INTERNAL DEFAULT SETTINGS, BECAUSE OF: bea.jolt.ServiceException: Invalid Session
We've detected that your operating system is not supported by this website. For best results, use one of the following operating systems:
Mac OS X 10.6(Snow Leopard)
Mac OS X 10.5(Leopard)
iPad
Oracle Linux Enterprise
Mac OS X 10.4(Tiger)
Windows 8
Windows 7
Mac OS X 10.7(Lion)
Regarding Application Designer, both Database Type "Oracle" and Connection Type "Application Server", UserID "PSADMIN" and password "myname" login successfully. I view TUXLOG (current Tuxedo log file) and its last screen is below:
191723.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191723.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191723.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191724.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191724.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191724.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191724.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191724.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191725.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191725.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191725.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191726.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191726.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191726.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191726.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191726.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191727.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191727.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191727.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
191727.lucylinux.lucydomain!JSH.32462.2485226496.-2: JOLT_CAT:1626: "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password"
I View APPSRV_1023.LOG (current server log file) and its content is below:
PSADMIN.32259 (0) [2013-10-23T18:55:12.134](0) Begin boot attempt on domain PT853
PSAPPSRV.32290 (0) [2013-10-23T18:55:35.701](0) PeopleTools Release 8.53 (Linux) starting. Tuxedo server is APPSRV(99)/1
PSAPPSRV.32290 (0) [2013-10-23T18:55:35.923](0) Cache Directory being used: /home/user/psft/pt/8.53/appserv/PT853/CACHE/PSAPPSRV_1/
PSAPPSRV.32290 (0) [2013-10-23T18:56:19.256](2) App server host time skew is DB+00:00:00 (ORACLE PT853)
PSAPPSRV.32290 (0) [2013-10-23T18:56:23.504](0) Server started
PSAPPSRV.32290 (0) [2013-10-23T18:56:23.507](3) Detected time zone is EDT
PSAPPSRV.32338 (0) [2013-10-23T18:56:25.793](0) PeopleTools Release 8.53 (Linux) starting. Tuxedo server is APPSRV(99)/2
PSAPPSRV.32338 (0) [2013-10-23T18:56:26.003](0) Cache Directory being used: /home/user/psft/pt/8.53/appserv/PT853/CACHE/PSAPPSRV_2/
PSAPPSRV.32338 (0) [2013-10-23T18:57:08.871](2) App server host time skew is DB+00:00:00 (ORACLE PT853)
PSAPPSRV.32338 (0) [2013-10-23T18:57:10.662](0) Server started
PSAPPSRV.32338 (0) [2013-10-23T18:57:10.663](3) Detected time zone is EDT
PSSAMSRV.32388 (0) [2013-10-23T18:57:12.159](2) Min instance is set to 1. To avoid loss of service, configure Min instance to atleast 2.
PSSAMSRV.32388 (0) [2013-10-23T18:57:12.168](0) PeopleTools Release 8.53 (Li nux) starting. Tuxedo server is APPSRV(99)/100
PSSAMSRV.32388 (0) [2013-10-23T18:57:12.265](0) Cache Directory being used: /home/user/psft/pt/8.53/appserv/PT853/CACHE/PSSAMSRV_100/
PSSAMSRV.32388 (0) [2013-10-23T18:57:59.414](0) Server started
PSSAMSRV.32388 (0) [2013-10-23T18:57:59.416](3) Detected time zone is EDT
PSADMIN.32259 (0) [2013-10-23T18:58:48.149](0) End boot attempt on domain PT853
PSAPPSRV.32290 (1) [2013-10-23T18:59:06.144 GetCertificate](3) Returning context. ID=PSADMIN, Lang=ENG, UStreamId=185906140_32290.1, Token=PT_LOCAL/2013-10-23-11.59.26.248432/PSADMIN/ENG/vSz0ix+wq8d+zPRwQ0Wa4hcek0Q=
~
I think the error is indicated in TUXLOG file "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password". The application password "myname" in Browser http://192.168.196.102:8000/ps/signon.html page is not working. I use the same password "myname" to login Data Mover Bootstrap mode, Application Designer, and Application Server psadmin configuration successfully. I have tried a few other passwords in Browser http://192.168.196.102:8000/ps/signon.html page but not working.
My question is:
How to solve Sign In issue on http://192.168.196.102:8000/ps/signon.html that is "ERROR: Jolt client (ip address 192.168.196.102) does not have proper application password" ?
Thanks.

Dear Nicolas,
Hello. I have used the same password for "DomainConnectPswd" in the file Configuration.properties with that for Application Server setting. Eventually, UserID PSADMIN sign in http://192.168.196.102:8000/ps/signon.html successfully. PeopleTools 8.53 runs correctly in Browser.
It seems that whether upgrade Oracle Linux 5.0 to the latest 5.10 does not have effect !
I am very grateful to your great help for this installation of PT8.53 with Linux and Oracle Database !

Retrieve Client IP Address in a Oracle WebServices Manager Custom Policy

Hi everybody,
For some reasons i had to implement a custom policy in the OWSM, to restrict the access to webservices by Client IP Addresses. I´ve been following the examples for custom policies mentioned in the books: "Oracle Web Services Manager, Oracle Web Services Manager" by Sitaraman Lakshminarayanan, and the "Oracle® Web Services Manager Extensibility Guide 10g (10.1.3.3.0)" by Oracle. I followed the examples mentioned in those books to implement my Custom policy, the policy is successfully deployed to OWSM and it works, only by the issue that when i want to retrieve the Client Ip address it returns null, and following the example by the Oracle Guide, the HttpServletRequest its also returns null, im desperated because in every site that i finally find some info about it, quotes any of these 2 examples in those books, and mine doesnt work! this is the code of the custom policy, i´ve combined the 2 aproaches:
package project1;
import com.cfluent.ccore.util.logging.ILogger;
import com.cfluent.ccore.util.logging.Level;
import com.cfluent.ccore.util.logging.LogManager;
import com.cfluent.pipelineengine.container.MessageContext;
import com.cfluent.policysteps.sdk.AbstractStep;
import com.cfluent.policysteps.sdk.Fault;
import com.cfluent.policysteps.sdk.IMessageContext;
import com.cfluent.policysteps.sdk.IResult;
import com.cfluent.policysteps.sdk.InvocationStatus;
import com.cfluent.policysteps.sdk.Result;
import java.util.HashMap;
import java.util.Iterator;
import java.util.Vector;
import javax.servlet.http.HttpServletRequest;
public class CustomPolicy extends AbstractStep {
private static String CLASSNAME = CustomPolicy.class.getName();
private static ILogger LOGGER = LogManager.getLogger(CLASSNAME);
private String allowedIpAddress = null;
private String allowedRoleName = null;
private String protectedServiceMethodName = null;
public CustomPolicy() {
public void init() throws IllegalStateException {
// nothing to initialize
public void destroy() {
* This is the main method which will validate that the request is coming from
* the correct IP Address and has permission to access the specified metod.
public IResult execute(IMessageContext messageContext) throws Fault {
LOGGER.entering(CLASSNAME, "execute");
Result result = new Result();
result.setStatus(IResult.FAILED); //initialize result
String processingStage = messageContext.getProcessingStage();
LOGGER.log(Level.INFO, "Processing stage is " + processingStage);
HttpServletRequest httpServletRequest = (HttpServletRequest)
messageContext.getProperty("javax.servlet.request");
String remoteAddr = httpServletRequest.getHeader("Host");
LOGGER.log(Level.SEVERE, "Dir IP:"+remoteAddr);
String remoteHost = httpServletRequest.getRemoteHost();
LOGGER.log(Level.INFO, "ADDR" + remoteAddr+ "HOST"+remoteHost);
boolean isRequest =
(IMessageContext.STAGE_REQUEST.equals(messageContext.getProcessingStage()) ||
IMessageContext.STAGE_PREREQUEST.equals(messageContext.getProcessingStage()));
//Execute the step Only when its a Request pipeline else return success
if (!isRequest) {
result.setStatus(IResult.SUCCEEDED);
return result;
MessageContext msgCtxt = (MessageContext)messageContext;
String _MethodName = msgCtxt.getRequest().getMethodName();
LOGGER.log(Level.INFO,
"Writing Allowed IP Addr before creating SOAP header " +
allowedIpAddress);
LOGGER.log(Level.INFO,
"Writing Remote IP Addr before creating SOAP header " +
msgCtxt.getRemoteAddr());
/*LOGGER.log(Level.INFO,
"Writing Remote IP Addr before creating SOAP header " +
remoteAddr);*/
String cadTempo = allowedIpAddress;
Vector vect = new Vector();
for (int i = 0; i < allowedIpAddress.length(); i++) {
if (cadTempo.indexOf(",") != -1) {
//vect.add(cadTempo.substring(0, cadTempo.indexOf(",") - 1));
vect.add(cadTempo.substring(0, cadTempo.indexOf(",")));
cadTempo =
cadTempo.substring(cadTempo.indexOf(",") + 1, cadTempo.length());
LOGGER.log(Level.INFO,
"AQUI111");
} else {
if (!cadTempo.equalsIgnoreCase("")) {
vect.add(cadTempo);
LOGGER.log(Level.INFO,
"AQUI222");
break;
for(int i=0;i<vect.size();i++){
String temp = (String)vect.get(i);
if (temp.equals(msgCtxt.getRemoteAddr()) &&
_MethodName.equals(protectedServiceMethodName)) {
LOGGER.log(Level.INFO,
"AQUI333");
result.setStatus(IResult.SUCCEEDED);
break;
} else {
msgCtxt.getInvocationStatus().setAuthorizationStatus(InvocationStatus.FAILED);
LOGGER.log(Level.INFO,
"AQUI444");
/*if(allowedIpAddress!=null){
result.setStatus(IResult.SUCCEEDED);
/*if (allowedIpAddress.equals(msgCtxt.getRemoteAddr()) &&
_MethodName.equals(protectedServiceMethodName)) {
result.setStatus(IResult.SUCCEEDED);
} else {
msgCtxt.getInvocationStatus().setAuthorizationStatus(InvocationStatus.FAILED);
// Set the result to SUCCESS
//result.setStatus(IResult.SUCCEEDED);
return result;
public String getIpAddress() {
return allowedIpAddress;
public void setIpAddress(String IpAddress) {
this.allowedIpAddress = IpAddress;
LOGGER.log(Level.INFO, "IP Address is.. " + allowedIpAddress);
public String getServiceMethodName() {
return protectedServiceMethodName;
public void setServiceMethodName(String serviceMethodName) {
this.protectedServiceMethodName = serviceMethodName;
public String getRoleName() {
return allowedRoleName;
public void setRoleName(String roleName) {
this.allowedRoleName = roleName;
And the xml:
<csw:StepTemplate xmlns:csw="http://schemas.confluentsw.com/ws/2004/07/policy"
name="Custom authenticate step" package="project1"
timestamp="Oct 31, 2005 05:00:00 PM" version="1"
id="0102030405">
<csw:Description>Custom step that authenticates the user against the
credentials entered here. This step requires Extract
credentials to be present before it in the request pipeline.</csw:Description>
<csw:Implementation>project1.CustomPolicy</csw:Implementation>
<csw:PropertyDefinitions>
<csw:PropertyDefinitionSet name="Basic Properties">
<csw:PropertyDefinition name="Enabled" type="boolean">
<csw:Description>If set to true, this step is enabled</csw:Description>
<csw:DefaultValue>
<csw:Absolute>true</csw:Absolute>
</csw:DefaultValue>
</csw:PropertyDefinition>
</csw:PropertyDefinitionSet>
<csw:PropertyDefinitionSet name="Custom Access Rules">
<csw:PropertyDefinition name="IpAddress" type="string" isRequired="true">
<csw:DisplayName>IpAddress</csw:DisplayName>
<csw:Description>IP Address that is allowed access</csw:Description>
<csw:DefaultValue>
<csw:Absolute>192.168.0.1</csw:Absolute>
</csw:DefaultValue>
</csw:PropertyDefinition>
<csw:PropertyDefinition name="ServiceMethodName" type="string"
isRequired="true">
<csw:DisplayName>ServiceMethodName</csw:DisplayName>
<csw:Description>Service Method Name that is Protected (Secured)</csw:Description>
<csw:DefaultValue>
<csw:Absolute>getTime</csw:Absolute>
</csw:DefaultValue>
</csw:PropertyDefinition>
</csw:PropertyDefinitionSet>
</csw:PropertyDefinitions>
</csw:StepTemplate>
Please any tip or idea is welcome, thanks in advance for the help.
Carlos.

Hi again
copied your code for testing. And it works fine.
So both the code and policy-step definition is fine, log output below.
What is your log output?
Using soapui to send the request will give the ip of my localhost, using the test client will give the ip of the server, because that is the actual client.
I guess the server ip is 192.168.0.1 in your case, as you are testing from test console.
<b>anyway, results from SOAPUI:</b>
2009-05-19 09:52:15,096 FINE [HTTPThreadGroup-4] CSWComponent - Executing policy step. Policy='SID0003004', Step Name='Custom Policy Step', Step Class='com.*.soa.wsm.CustomPolicy'
2009-05-19 09:52:15,096 FINER [HTTPThreadGroup-4] wsm.CustomPolicy - com.*.soa.wsm.CustomPolicy execute:ENTERING
2009-05-19 09:52:15,096 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - Processing stage is Request
2009-05-19 09:52:15,096 SEVERE [HTTPThreadGroup-4] wsm.CustomPolicy - Dir IP:hostname.domain:8890
2009-05-19 09:52:15,096 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - ADDRhostname.domain:8890HOST10.47.89.116
2009-05-19 09:52:15,096 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - MethodName=getHostNameElement
2009-05-19 09:52:15,096 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - Writing Allowed IP Addr before creating SOAP header 10.47.89.116, 192.168.0.1
2009-05-19 09:52:15,096 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - Writing Remote IP Addr before creating SOAP header 10.47.89.116
2009-05-19 09:52:15,096 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - AQUI111
2009-05-19 09:52:15,096 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - AQUI222
2009-05-19 09:52:15,097 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - AQUI333
2009-05-19 09:52:15,097 FINER [HTTPThreadGroup-4] agent.Agent - com.cfluent.agent.Agent intercept:ENTERING
<b>But if I use the test client the remote IP would be 10.47.137.50 and execution fails, as code is written</b>
<i>
2009-05-19 09:54:12,266 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - Writing Allowed IP Addr before creating SOAP header 10.47.89.116, 192.168.0.1
2009-05-19 09:54:12,266 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - Writing Remote IP Addr before creating SOAP header 10.47.137.50
2009-05-19 09:54:12,267 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - AQUI111
2009-05-19 09:54:12,267 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - AQUI222
2009-05-19 09:54:12,267 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - AQUI444
2009-05-19 09:54:12,267 INFO [HTTPThreadGroup-4] wsm.CustomPolicy - AQUI444
2009-05-19 09:54:12,267 FINE [HTTPThreadGroup-4] CSWComponent - Step execution failed: Policy=[SID0003004] Pipeline=[Request] Step Name=[Custom Policy Step] Step Class=[com.tandberg.soa.wsm.CustomPolicy]
2009-05-19 09:54:12,267 FINER [HTTPThreadGroup-4] common.PrepareForServiceStep - Step PrepareForServiceStep called
</i>

Duplicate Client IP Address Matching Teamed Adapter on Server

I am experiencing a problem with a client's WLAN and client IP address conflicts.
Basically every wireless client reports a problem that it is having an IP Address conflict with another device on the network (wired).
The device in mention is a Dell Server with Teamed network cards. They have three of them and clients are reporting conflicts with all three.
On investigating further there is no address conflict as the "Teamed Adapter" has a completly different network address (static) and the wireless clients are using the internal WLC DHCP server in a different range. (although it is all one flat network).
The clients report that there is an address conflict, the MAc that it gives is the Teamed Server but the IP address is only its own and not on the Teamed Adapter.
Has anyone seen this before or had a problem with "Teamed Adapters" on servers.
Our environment is:
WLC 4402-50 running 5.2.178
Flat Network.
Thanks

Hi Roman,
thanks for your reply.
Basically what i have found is that it Servers running Microsoft Windows 2003 or Windows 2000, that have teamed NICs using Broadcom Advanced Server Programs (BASP) in an active/active team, respond to other server's gratuitous ARP packet with an incorrect IP address. The Microsoft Windows server will respond to the other server sending the gratuitous ARP, with the Microsoft Windows server team MAC address, but with the other server's IP address in the sender field of the packet. This causes the other system to respond as if there is a duplicate IP on the network.
Fix is to upgrade to BASP driver version 6.2.32, or newer. This version of the BASP driver was first included with the Broadcom NetXtreme Gigabit Ethernet Software.
An upgrade of the drivers apprently will fix this issue althouh i have tried it on 3 servers with this ocnfiguration and it fixed it for two of them.
The work around is to disable the active/active NIC team and use an active/standby team instead.
Someone else on this forum must of come across this before i am sure?
Anyway if it does resolve the issue i will post it back here so that anyone else in the future with this problem has a resolution!!
thanks

Cisco WLC Client MAC address backup to new Controller & ISE

Hi All,
We have an existing 4400 controller with MAC filtering for clients configured. Right Now, we are migrating to 5500 WLC and ISE setup.
We want to use MAC filtering due to company policies on the new Controller as well as ISE.
Is there a way (from GUI/CLI) that we can export the client MAC Addresses into an Excel file from existing WLC to new WLC & ISE?
Thanks,
CJ

On the CLI issue a show macfilter summary and then import that into excel or a text editor.
Sent from Cisco Technical Support iPhone App

Capture Client IP address in Oracle Portal

Hi,
I just thought to post the solution I figured out which I can't find anywhere.
The instructions should allow you to add the dynamic page portlet to a page to see the client ip address:
1. Login to Portal as an admin.
2. Click on the Navigator link.
3. Create a new page group.
4. Create a new page within the page group.
5. In the page region, click on the add portlet icon.
6. In the Available Portlets, click on Portlet Builders > Additional Portlet Builders > Dynamic Page Portlet
7. This will place the Dynamic Page Portlet on the page. You can then click on Define to customize the dynamic page.
8. In the HTML section of the dyamic page portlet wizard (after clicking define and giving it a name), enter code like the following:
<HTML>
<HEAD>
<TITLE>Welcome User</TITLE>
</HEAD>
<BODY>
<ORACLE>DECLARE
l_curr_cgi_ip varchar2(30) := owa_util.get_cgi_env('remote_addr') ;
l_curr_ip varchar2(30) := portal.wwctx_api.get_ip_address;
BEGIN
htp.p('<H3>OWA_UTIL.GET_CGI_ENV returns =>' || l_curr_cgi_ip || '</H3>');
htp.p('<H3>WWCTX_API.GET_IP_ADDRESS returns =>' || l_curr_ip || '</H3>');
END;
</ORACLE>
</BODY>
</HTML>
9. Finish the wizard (you can take defaults).
10. Display the page. The portlet should have the information.
==========
Otherwise you can create a dynamic page under a provider:
1. Login to Portal as an admin.
2. Click on the Navigator link.
3. Click on the Provider tab.
4. Click on Locally Built Providers.
5. Click on Example Application db provider (this is a sample).
6. Once you click on the Example Application, it will list some of the default forms, reports, etc... At the top, there is the following:
Create New... Create New...Form, Create New...Report, Create New...Chart, Create New...Calendar, Create New...Dynamic Page, Create New...XML Component, Create New...Hierarchy, Create New...Menu, Create New...URL, Create New...Frame Driver, Create New...Link, Create New...List of Values, Create New...Data Component
Click on dynamic page.
7. Give it a name and click next.
8. Replace the sample HTML with:
<HTML>
<HEAD>
<TITLE>Welcome User</TITLE>
</HEAD>
<BODY>
<ORACLE>DECLARE
l_curr_cgi_ip varchar2(30) := owa_util.get_cgi_env('remote_addr') ;
l_curr_ip varchar2(30) := portal.wwctx_api.get_ip_address;
BEGIN
htp.p('<H3>OWA_UTIL.GET_CGI_ENV returns =>' || l_curr_cgi_ip || '</H3>');
htp.p('<H3>WWCTX_API.GET_IP_ADDRESS returns =>' || l_curr_ip || '</H3>');
END;
</ORACLE>
</BODY>
</HTML>
9. Finish the wizard. This should show the portlet and the value. You can then add this portlet to a page.
Note: portal.wwctx_api.get_ip_address will fetch your read client IP address.
If the page you uses a UI template, you might get Error WWC-50003 When Clicking On The Portlet Define Link
Then you have to add #PAGE.BASE# in the <HEAD> of the template and you can define the dynamic page portlet.
It is tricky to pass the IP address inside the code, I solved the issue with the help of JavaScript.
<HTML>
<HEAD>
<TITLE>Welcome User</TITLE>
</HEAD>
<BODY>
<ORACLE>
DECLARE
l_curr_ip varchar2(30) := portal.wwctx_api.get_ip_address;
BEGIN
htp.p('<script type="text/javascript">');
htp.p('ipClient(''' || l_curr_ip || ''');');
htp.p('</script>');
END;
</ORACLE>
</BODY>
</HTML>
I delared a hidden variable in the portlet I need the IP address & have set that value i the javascript function which I call in between <oracle></oracle>
function ipClient(ipAddr){
document.getElementById('clientIP').value = ipAddr;
Once I set the variable I can easily get it any where.
Hope this helps to solve your issue.
Thanks,
Sowji.

You could have found it here:
http://www.morganslibrary.org/reference/owa_util.html
and another solution here:
http://www.morganslibrary.org/reference/sys_context.html
Both part of the library at:
http://www.morganslibrary.org/library.html
you might want to bookmark the page.

Blocking Client MAC Addresses at Sup720/WLSM?

I want to block client MAC addresses at the central 6500, where the WLSM is located. Is there any solution like "dot11 association mac-list" at the accesspoints? I tried an "access-expression" on the tunnelinterface, but it did not work. Any suggestions?

Here is an example of config
switch(config)# mac access-list extended ARP_Packet
Switch(config-ext-nacl)# permit host 0000.861f.3745 host 0006.5bd8.8c2f 0x806 0x0
Switch(config-ext-nacl)# end
Issue the vlan access-map map_ name command and the action drop command, which is the action to perform.
The vlan access-map map_ name command uses the MAC access list that you created to block ARP traffic from the hosts.
Switch(config)# vlan access-map block_arp 10
Switch (config-access-map)# action drop
Switch (config-access-map)# match mac address ARP-Packet
Add an additional line to the same VLAN access map to forward the rest of the traffic.
Switch(config)# vlan access-map block_arp 20
Switch (config-access-map)# action forward
Choose a VLAN access map and apply it to a VLAN interface.
Issue the VLAN filter vlan_access_map_name vlan-list vlan_number command.
Switch(config)# vlan filter block_arp vlan-list 2

I am automating the process of sending appointment reminders to my clients. I started with an alert with an email in calendar using the clients email address as a custom entry in my me card in my contacts. this was resulting in three emails being sent wit

I am automating the process of sending appointment reminders to my clients. I started with an alert with an email in calendar using the clients email address as a custom entry in my me card in my contacts. this was resulting in three emails being sent with slightly different versions of the same address (see my previous post). Heating someone else's suggestion I created a workflow file to send an email and calling that file from an alert on my calendar. This is working and sends only one email to the client.
My calendar is on I cloud and I access it from three different computers so I can keep my appointment calendar current. The files that send the email only exist on one computer. My other computers show error messages when those emails get sent. It seems that each computer wants to send the email. It's a small problem but is there a way that I could not get those alerts.
But appreciate any thoughts about this. It seems like both problems might be related to the iCloud system.
Thank you in advance,
Michael

Good work, catch so far Michael, does seem to be a "feature" of iCloud syncing, not sure what you could do to disable it.

HT4061 My gateway PC is locked up after itunes update. When i restarted the computer for the hangers to take effect. Now my pc is locked up. It gives me a client Mac address and no boot file name received. What happened, and how do I get my pc back?

jute way pc locked up after iTunes update. It says client Mac address 001320 be ad 25 . PXE E53 No boot file name received
pXE MOF. Exiting Broadcom PXE. ROM . How do I unlock my pc?

jute way pc locked up after iTunes update. It says client Mac address 001320 be ad 25 . PXE E53 No boot file name received
pXE MOF. Exiting Broadcom PXE. ROM . How do I unlock my pc?

HT4061 I downloaded an iTunes update on my HP. PC and restarted the computer for the hangers to take effect. Now my pc is locked up. It gives me a client Mac address and no boot file name received. What happened, and how do I get my pc back?

I downloaded an iTunes update and when ashen I restarted my pc it locked up. It says client Mac address 001320bead25, PXE E53 No boot file name received. PXE MOF. Exiting Broadcom pie rom. How do I get my pc back!

When you installed iTunes on your work computer, then connected your iPad to that computer, it wiped what was on the iPad, then put the iTunes library (nothing) from the work computer onto the iPad. You can try copying the iTunes folder from your home computer over to your work computer, but since the apps were bought with a different account, they may not load or update properly.

How do I get list of client IP Addresses using new Airport Utility v6.3?

I have purchased and Airport Time Capsule 3TB (newest model). Previous models were still compatible with Airport Utility 5.6 and I could use "manual" mode to get a list of client IP addresses attached to the device. The new Airport Time Capsule is only compatible with Airport Utility 6.3 and I cannot figure out how to get a list of client IP addresses with this new model. Does anyone know how to do this?

Try a ping broadcast - for example if your network were 192.168.1.xxx (netmask of 255.255.255.0) try this from a Termnal.app window (located in /Applications/Utilities):
ping 192.168.1.255
If you have a different type netmask, you need to put 255's where the 0's are in your netmask.
Everyone on the local network (the 192.168.1.xxx network) should reply that is up and running unless you have them setup to not respond to pings (the WAN port on your TC should not reply cause it's in a different network) and you have your list of clients on the network. If you setup the TC to dedicate a range of addresses for WiFi clients you can even identify which of them are wired and which are wireless.
good luck.

UNABLE TO RETRIEVE THE CLIENT IP ADDRESS AND HOST NAME OF A PORTAL USER

I'm trying to retrive the client IP address and host name of a portal user
trying to access a portal page using APIs:
PortletRenderRequest portletRequest =
(PortletRenderRequest)request.getAttribute(HttpCommonConstants.PORTLET_RENDER_REQUEST);
HttpServletRequest servletRequest =
(HttpServletRequest)portletRequest.getAttribute(HttpCommonConstants.SERVLET_REQUEST);
String l_szClientIPAddress = servletRequest.getRemoteAddr();
String l_szClientHost = servletRequest.getRemoteHost();
but i found that for all portal users on different machines IP addresses, the
returned IP is the same for all which is Portal middle tier IP address.
So how can retrive the IP addess of a portal user trying to access a portal
page ?

Brijesh,
Do you mean how to see hostname/ip address of client requests processed by the server? If yes, depending on what's your front ending component - Web Cache or OHS, you can configure the access log format to have this information recorded in either of these component's access log file.
For Web Cache access log file, refer this:
http://download.oracle.com/docs/cd/B14099_19/caching.1012/b14046/diagnostics.htm#sthref2090
For OHS access log file, refer this:
http://download.oracle.com/docs/cd/B14099_19/web.1012/b14007/servlog.htm#sthref439
By default, both Web Cache and OHS are configured to use Common Log Format (CLF) that does record hostname/ip address so if you haven't made any changes to log format, this info is already there for you. Look for $ORACLE_HOME/webcache/logs/access_log file for Web Cache and $ORACLE_HOME/Apache/Apache/logs/access_log file for OHS.
Thanks
Shail

How to print the client ip address at the server side( reqd for logging )??

Hello everybody...
joined this forum recently.....
In RMI programming.... is there any way by which the server can know the the Client ip address or machine name.... i want to know this bcoz i need to create a log file as to who all had connected withe the server..
need a solution soon..... thanks in advance....

@ejp....
thanks buddy....
u made my world a better place to live.....

How to retrieve the client IP address when Apache acts as a proxy for Tomca

Hello,
I am trying to retrieve the client IP address accessing the web
services. Because Apache is our proxy for all requests, when I try to
retrieve the client IP I always get the localhost IP: 127.0.0.1
The following code returns the localhost IP:
MessageContext msgContext = MessageContext.getCurrentContext();
if(msgContext != null) {
return msgContext.getProperty(Constants.MC_REMOTE_ADDR).toString();
return "Unknown";
From a servlet, obtaining the client IP address can be achieved using
this code.
String ipAddress = request.getHeader("x-forwarded-for");
if (ipAddress == null) {
ipAddress = request.getHeader("X_FORWARDED_FOR");
if (ipAddress == null){
ipAddress = request.getRemoteAddr();
return IPaddress ;
Any help is greatly appreciated.
Thank you very much

@ejp....
thanks buddy....
u made my world a better place to live.....

How can I get Client IP Address in oracle?senthil

How can I get Client IP Address in oracle?senthil

Hi,
Following query can help you to get the Client IP Address.
select sys_context('userenv','ip_address') from dual;
Thanks,

Client IP Address issues

Similar Messages

Maybe you are looking for