Clients and Access points?

Hello everyone! I have a specific question?
You can configure the controller to clients so that they can connect to certain access points. For example, we have 4 access points and 5 clients. Clients 1, 3, 4 can be connected to the APs 1, 3, but can not connect to the APs 2, 4. And clients 2, 5 can be connected to the APs 1, 2, 3, but can not connect to the AP 4.
And is it possible to carry out the same operations with SSIDs? For example SSID 1 see clients 1, 2, but don't see clients 3, 4, 5. And SSID 2 see clients 3, 4, 5, but don't see clients 1, 2.
Or that is not practicable?

Why this approach. What is the business need. You can broadcast different SSIDs on different Aps via ap groups.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

Similar Messages

  • How many clients support access points 1602, 2602, 3602?

    Hi! How many clients support access point 1602, 2602, 3602. I have found for example that the 1602 supports 32 ClientLink clients and max 128 clients, APs 2602, 3602 supports 128 ClientLink clients and max 200 clients. But is it really? And can we say for example that the AP 2602 will withstand max 200 clients?

    The reason the answer varies so much, is because there are so many variables (this is also why the value ranges so much from one manufacture to the next).  When determining the answer you are looking for you need to consider the following factors and likely more:
    AP model and the features it supports
    single, dual, or tri radio AP
    20, 40, or 80Mhz wide channels
    Device type (b/g, b/g/n, a/b/g/n, a/b/g/n/ac, spatial stream support, and channel width support)
    Security/QOS method(s) employed
    Average distance from the AP
    Obstructions between devices and radios
    Number of competing radios for the same channel
    Data rates configuration
    Rogue detection/mitigation configuration
    Surrounding client density not just the area of concern client density
    Noise floor levels
    Application types/per user network load (is it heavy like YouTube traffic or a drone on the network like Pandora)
    Network latency on the switching side - including the internet circuit
    Application of per SSID, per user, and or per application rate limiting
    The list continues, but I think you get the idea
    I have personally seen 80 devices on a 5Ghz radio of a 3500 access point with several other access points and at least 200 other clients in the area and it was working well.  That being said I would never design to expect that many on a single radio, but I think it is better said that you can safely design for 20-30 clients per 2.4Ghz radio and 25-40 clients per 5Ghz radio.
    The default statement of 20-25 per AP and similar low expectation statements concerning Cisco wireless have been around for many years.  It is now 2014.  About 65% of clients support 5Ghz, ~9% support AC (already), ~90% support some form of N, and ~0.01% support B only.  The landscape of wireless is changing fast making questions like this one have ever changing answers.
    I hope this helps :).
    John

  • Upgrading controllers and access points through NCS

    I am currently trying to upgrade all of my controllers and access points to the newest version.  I have downloaded the file and loaded it on the ftp server running on the Cisco NCS server.  I tried to go to configure>controllers and Download Software(ftp) and go.  I setup the schedule and it says failure.  The details say %Error:Code file transfer failed - Connection Timeout.  Sorry if this is a basic thing that I am missing.  I have tried using an internal ftp server as well and it errors out also.  Any help would be greatly appreciated.

    It is setup with NCS Prime running 4 WiSM blades and 3 WiSM 2 blades in 6509 chassis.  I am going in through NCS and doing configure controllers and download software(ftp) from the select a command dropdown.  When I setup it up this way I have to select schedule unless I want it to automatically download and reboot the controllers, which I was trying to avoid so that I could do it during the day.  It just keeps timing out on the download portion. 

  • Can a single Access Point support both bridge mode and Access Point mode at the same time

    Hi Guys
    Does anyone know which access point can work in both bridge mode and AP mode ?
    Cheers

    Well what are you trying to cover. If its really a large outdoor area, then look at the mesh AP. Those require a WLC. Autonomous or stand alone ap can perform bridging on one radio and client access on another. You can also look at AP that support indoor mesh that also controlled by a wlc. If your putting APs outdoors, then look at the outdoor mesh.
    Thanks,
    Scott Fella
    Sent from my iPhone

  • NW Business Client and accessing SAP services via web pages

    Hi all,
    We currently use Business Connector to access our SAP environment via web pages. We looked at NW eSOA but decided against implementing it. Does Business Client offer anything that helps access SAP apps and data from a custom web site better the Business Connector?
    Thanks in advance,
    Tom

    Tom
    I am assuming you are using SAP Business Connector in your landscape to connect to back end SAP systems from  your web applications. Your question now is that if business client can let you access SAP data for your web pages instead of the business connector. Point to not here is that Business client, as the name implies, is just a client with single point of access for SAP screens. That means, you can access traditional SAP transactions, WebDynpro screens, BSP pages, Portal screens etc in one single client. In very raw terms, Business client acts (or replaces) as your browser. It is not going to provide you any out of the box integration with backend system rather just act as a window. You options at this point are
    1) Use your existing webpages but instead of getting data from the backend system through business connector, get the data using webservices.
    2) Use PI as middleware tool and get the data from backend SAP system
    3) Stay were you are but deal with high cost of ownership.
    Thanks
    KK

  • Help with N97 and Access points after V20 upgrade

    Hi Guys,
    I'm hoping someone can help me - I have an 505 uk unit and have changed to a generic euro product code to get the V20 software ( as theres a 2 week wait minimum for the network to release its custome version ) and its working brilliantly - except - in connections all my accesspoints have gone - I now show 13 uncategorised access points which I cant expand or open and it wont let me delete the lot as it says its protected Anyone able to sort this out and tell me what to do so I can get back to Internet and Contract WAP etc... destinations?
    Much Appreciating any help.
    Alex

    Hi Alex,
    I am not sure what kind of applications are preloaded in your location.  I suppose the problem you faced is unable to delete certain definitions under the Destinations setting?
    If a hard reset is not an option (not for me as I have purchased apps from the OVI store), I would create a dummy Destination to house all these unwanted definitions.  That way, so long as the default connection does not utilize this dummy Destination, I think you are OK.  Hope this helps.
    Visit http://www.WilfridWong.com - where all good things are meant to be shared!

  • Airport Express and Range Extenders and Access points.

    My setup is as follows
    Main wireless router is a Dlink DIR-635, with SSID 'id1'
    A Edimax range extender, with SSID 'id2'
    A small network with a PC and a mediaplayer connected to a Jensen router acting as a switch. This network is connected to the wireless network with SSID 'id1'
    through a TP-Link access point.
    I want to stream music from my PCs and Ipad to the Express using Airplay.
    The 'id2' network has the best signal in the room where I want the Express.
    Connected the Express to this network, but it didn't show up as an available speaker neither on the Ipad nor on my PCs.
    Connected the Express to the other network 'id1'. Now it shows up on my Ipad and a portabel PC. Both connected to network with SSID 'id2'.
    But the PC connected to the wireless network through the TP-link, is still unable to find the Express.
    Does this sound familiar to anyone?
    What protocoll does Airplay use? Does the Express send any broadcast messages to inform other devices that is is in the network?
    Seems to me that the Airplay protocoll is filtered by the extender and the access point.
    Any hints will be appreciated.

    If you are asking about "extending" or "repeating" the wireless signal, you will need both an Apple main router and an Apple extending device.
    The AirPort Express (and other Apple routers) can only "extend" a wireless signal from another Apple router.

  • WLC upgrade license and access point

    Hi everyone,
    I need suggestion regarding wlc 5508  upgrade license. Right now i have 150 license for access points. There will be upgrade around 300 access points. So we are planning to buy new license until the maximum capacity of 5508 (500 licenses).
    Our management ip address is 192.168.50.x/24 . so all the access point are pointed to this management ip address (in the same subnet)
    First question,
    Because there will be an upgrade to around 450 access point. The current management ip address will not be enough.
    Please, give me the  best suggestion ?
    Should i create another management ip address ? or I need to make a bigger subnet using the current management ip address ?
    if i create a bigger ip address, the current access points must be set again yups ?
    Second question
    There will be a new link connected to the wlc, and i want to create new user subnets.
    what is the best practices for this matter ?
    if there are better suggestion, please let me know, i am still learning about wireless
    I have attached the topology.
    Thank you
    Fanie

    For an example, a 5508 can support up to 500 AP's, and the AP's can be in one large subnet or be in many different subnets and or even different locations. As long as the ap knows how to discover the WLC or the ap already had joined the WLC, then the AP's don't have to be on the same subnet as the WLC. The easiest way to have AP's join is to stage them on the same subnet as the WLC management and then move them to a different subnet. I would probably have no more than 100 AP's per subnet, but that's me. Stage some AP's on the management subnet that the WLC is on and then when the AP's join and complete downloading code, change the switch port Vlan and shut and no shut the port. The ap will come back up and join the WLC.
    Sent from Cisco Technical Support iPhone App

  • N96 Video Ringtones and Access points

    2 months on and my video ringtones still dont work, they try to start and then go to nokias horrible ringtone, also under email and realplayer the phone refuses to change the default access point entered which in my case with realplayer is none, this means my realplayer wont streaming anything!
    Has anyone else had this issue.

    You might have to categorise your access points manually, for example, move (or copy) your wireless lan network called 'Hello' to the internet access point group.
    Also you should be able to select the access point real player uses within the settings menu, are you saying that only 'None.' is available? If so, thats weird!
    Are your video ring tones on the memory card? (not mass memory) as this could slow down the opining of the videos, try using the default ones that came with the phone and see if they work.
    If you can update your phone's firmware, like el_loco said, do it!
    Tony

  • My router and access point reboots when trying to stream content from iOS devices or mac to my apple tv.

    the zycel N series access point and cisco router reboots when i try to stream or mirror onto apple tv using air play. What can be the cause of the problem?

    Please answer as many of the following questions as you can. You may already have answered some of them. In that case, there's no need to repeat the answers.
    Have you restarted your router and your broadband device (if they're separate) since you first noticed the problem? If not, do that now and see whether there's any change.
    If your browser is Safari, then from the Safari menu bar, select
    Safari ▹ Preferences... ▹ Privacy ▹ Remove All Website Data
    and confirm. Any change?
    If you're running OS X 10.9 or later, select the Advanced tab in the Preferences window and uncheck the box marked
    Stop plug-ins to save power
    Any change?
    Quit and relaunch the browser. Any change?
    Log out and log back in. Any change?
    Enable Private Browsing in the Safari menu. Any change?
    Are any other web browsers installed, and are they the same? What about other Internet applications, such as iTunes and the App Store?
    If other browsers and Internet applications are also affected, follow these instructions and test. Any change?
    If Parental Controls is active for any user, please turn it off and test. Any change?
    If only Safari is affected, launch the Activity Monitor application and enter "web" (without the quotes) in the search box. If a process named "Safari Web Content" is shown in red or is using more than about 5% of a CPU, select it and force it to quit by clicking the X or Quit Process button in the toolbar of the window. There may be more than one such process. Any improvement?
    Again, if only Safari is involved, open the iCloud preference pane and uncheck the box marked Safari, if it's checked. Any change?
    Are there any other devices on the same network that can browse the Web, and are they affected?
    If you can test Safari on another network, is it the same there?
    If you connect to your router with Wi-Fi and you can also connect with Ethernet, do that and turn off Wi-Fi. Any difference?

  • Router and access point

    Likely either or. Of course if you "need" wireless you have to have an AP somewhere and many of them are capable of serving up DHCP and doing many functions of a small broadband thingy (I won't call these things "routers", "thingy" seems more appropriate)  :)

    which one i should use a router or access point to create a home network lab where i can play around with the DNS and DHCP configuration without changing the ISP router setting?? 
    This topic first appeared in the Spiceworks Community

  • Router and access point connection

    Tried to get smart today, took and set up my network with a wrt54gs the other day and still have some headaches after finally getting things to work. but my idea was to take my old wrt54g router and place it at the other end of my house for the wii system. I took the old router and changed the setting from gateway to router and gave it a new internal ip address. Everything worked fine, all the wired and wirless computers including the wii worked great, but when I went to my computer, where I installed the easylink program, it showed I changed networks. Do the setup crap again and it can not find the router but showed the old one as the new netork and could not connect, could not get internet or anything at this computer. But every other computer throughout the house was working great and connected to the net with no problem, the only one not connecting is the only one with easylink keeping it from connecting.
    So I disconnect the added router/access point and had to run setup again with easy link, once it was up again I reconnect the old router and everything was great, showed the old as an access point and all the devices on the network. So things are great until I close my lid and my computer goes into standby, when I open it up I have the same problem again, but this time I know what to do, and I find as long as I keep this computer on all is great, shut it down all others equipment still works fine all except for the one computer with easylink on it.
    Any ideas on to resolve this, I know people in the forums have said for a long time you can't use the two routers the way I have them set up, but it works great, the only problem is easylink keeps screwing me up on the one computer, if I moved the program to another computer it will do the same to that one and leave this one connecting just fine. So far my experience with easylink has been horrible, the only reason it was installed was because the box said it must be installed prior to anything else. before I just plugged things in and put in the settings I needed and life went on.

    Hey,
    I think you can try to update the firmware of the router, to check if that stops connection dropping. To update the firmware of router try this:
    Go to www.linksys.com/download and select correct model number and version number. Download the firmware and save it on your computer.
    Check the file it should be firmware image file like .bin etc. If it is a compressed zip file extract it to get firmware image file.
    Open setup page of router by typing http://192.168.1.1 in browser’s address bar, and typing password as "admin" and no user name.
    Go to administration tab there
    Go to firmware update sub-tab there
    Browse for the firmware image file and click update
    When update completes turn off modem & router.
    After 2 minutes turn on modem and after 2 more minutes turn on router & it will definately work!!!

  • Router and access point connected to FIOS router

    Here's my situation.  Just installed Verizon Fios which supplies their own Actiontec Wireless router.  I have an existing network which comprises a WRTG54Gv6 which was connected to a DSL modem for internet access originally and a WAP54G accesss point as a Repeater to extend the network wirelessly.  I have quite a few wired and wireless connection to this netwrok and wish to retain these devices. My question is, based on where I had to connect the new FIOS router(which is where the access point is) can I connect the WAP54 to the FIOS router(through a switch) and allow the combined WAP54/WRT54G network to still provide my network services and deactivate the wireless service from the FIOS router. How do I configure the FIOS router, the WRTG54 and the WAP54(if change neded).
    Thanks in advanced if anyone can help.

    Easiest way to configure the Verizon FIOS with Linksys is - Leave the Verizon FIOS unplugged from the Linksys Router and disconnect it's power cable.
    1. Connect a computer to the Linksys Router it's Internet Port...
    2. Access the web interface of the Linksys Router, change it's default address to 10.10.10.1 and leave it's DHCP Server Settings 'Enabled'. Once done you should Power cycle the Linksys Router.Don't change the Router Mode.
    3.Connect Verizon FIOS from it's Ethernet Port to the Linksys Router on the Internet Port.
    4. See if you can access the Internet...
    You can also have a look at this link to connect two routers.However, both the router's used in the link are linksys routers but you can still follow the link.

  • Downloadable ACLs and Access Points

    Is it possible to use Downloadable ACLs (via ACS) with WLAN Clients that attach to a 1200AP?
    I have tried but it is not working. I think it is because the AP is acting as a bridge to the clients and the ACLs are layer 3/4 aware, but i am new to Aironets. Thanks for any help and/or suggestions.

    No joke:  I reboot my WAPs (>1400 in 102 sites) as often as I can.  Always during early morning, say 4 am.
    Your main question is: HOW.
    The only way WCS/NCS or schedule a reboot.
    You can also enable EnergyWise.

  • Internet based management of SCCM clients and management points ?

    We have an SCCM backend infrastructure which is used to manage what is in affect multiple external organizations over the internet.  Currently each SCCM client is managed by the primary server directly over the internet. 
    Am I right that we could place a configmgr management point on the internal networks and for the clients to talk to this server when connected to the company network instead of all clients getting patched across the internet connection ?  Meaning that
    just the MP would communicate with our backend infrastructure ?

    So your internal clients are now connecting over the internet to the local MP? How does this setup look like exactly? How were the clients installed (parameters)?
    Torsten Meringer | http://www.mssccmfaq.de

Maybe you are looking for