CLOI_CHANGES_UPL_31 select routing

Hi All,
Does anyone knows how to select the routing when using function module CLOI_CHANGES_UPL_31.
I have tried to enter the routing group and counter number into CLOI_ORDI_IMP but doesn't work. Please kin
Thanks.

Dear
Please refer our earlier posting : CLOI_CHANGES_UPL_31 select routing
FM or BAPI for CM21
BAPI to change Production Order TaskStart Date & Time and Reduce Setup Time
Regards
JH

Similar Messages

Need help selecting router

Hello All,
I need some help in selecting the best router for our wireless setup. I have never setup a wireless network, so please forgive if I am a little lost. I have an older laptop, HP Pavilion ze4400 (windows xp) and a brand new gateway (windows 7). The gateway has a built in wireless adapter. The HP came with an 802.11b cardbus thingy. I have been told that an N router is the best, but I am concerned that it will not work with the older HP. Will an N router be backwards compatible with the b? If not, can I just buy a new adapter for the HP? If so, what router and adapter should I select?

Just about every 802.11n router sold will be able to operate in a "Mixed" mode, allowing you to use your B, G or N devices simultaneously. An 802.11n router will allow you to take advantage of the improved wireless capabilities with any device that supports N. So, no need to worry about backwards compatibility.
The only thing that may be a concern (depending on how old the 802.11b adapter is) is wireless security. Chances are it supports WPA security, but if not you can fall back to WEP or the better option, buy a newer adapter.

Select Routing Operation

Dear All,
I want to use routing oerations in program. I am using plpo table, but I have one problem, eg. in ca03 tcode for material 37 it is displaying 4 operaions like 20, 30, 40, 50. But in table plpo there is 10 operation also I want to avoid this operaion(10). Please tell me how to do it?
Thanks & Regards,
Roshani

after you select PLPO into an internal table:
delete internatablename where operation eq 10?

CA97- Selected routing ?

Hello dear all,
I have one material with 3 production versions.
When I launch CA97 transaction the task list of the first production version is not selected.
The routing with the first number is used for the calculation.
Do you know what is the rule?
May I change this behavior?
Thanks a lot.
Best regards,

Hello
A routing selection via production version is not available on CA97.
You can either enter the desired routing data (PLNNR, PLNAL etc.) or the routing is selected automatically via the selection ID. The selection ID is defined on the customizing transaction OPU5 for order type 'LA'.
BR
Caetano

Having to select router everytime I start up

Hi guys, hope you can help please.
Everytime I start up my Mac I have to go to my airport icon in the top corner, go down the list of routers it picks up and select my router (Netgear) I also have to do this if I put it to sleep too? Is there a reason it's not picking it up automatically?
Thanks for all help.

Welcome to Apple Discussions
Open System Preferences/Network, select your home location then click Advanced
Under Preferred Networks drag your Router to the top of the list and delete the rest that show
Click OK
When you go back to the previous screen check "Ask to Join new Networks"
Close the panel

Agent Selection/Routing Question

Hello:
I wanted to run a question by the group to get some feedback on a question I have surrounding Agent routing within UCCX (8.5 su4).
Here is the setup of the environment:
CSQ1: General
Routing Criteria: LAA
CSQ2: Spanish
Routing Criteria: Most Skilled
Agent1
has Skills of General and Spanish.
Their competency is the same within both skills.
Question: Calls are in queue for both CSQ's, although the call in the spanish CSQ has been in queue longer. And agent 1 goes ready. Whats currently happening is that agent 1 is getting another call from the General Queue as opposed to getting it from the spanish queue.
How do I ensure that agent 1 gets the call from the spanish CSQ over the general CSQ? Each CSQ needs to keep the Routing Criteria the same.
My thought is that it has to be one of these two items, if not a combination of both.
Decrease the Competency of all General agents to a (5) and Making the Spanish competency higher then 5.
in the script, for Spanish Calls use the Set Priority Node to increase Spanish queued calls to be at like a 5, to ensure all spanish calls have a higher priority then general Calls.
Any feedback would be appreciated!

Hi Sean
All calls on the system if you are not using priority steps already should be answered FIFO... provided that there are agents available in the queue that the first call came in (i.e. they meet the minimum competency). Competency, skills/LAA and all those algorythms only affect who gets the call, not which one is served first. The exception to that is if the competency excludes some agents from the CSQ completely.
So a call that arrives in 'Spanish' first should be routed to agents first, as long as there are agents available. Does the same apply if the agent is 'ready' but on a call for example? E.g. call voicemail as the agent, then put a call in to spanish, then one in general, and see which one comes through first.
Priority will work, but will mean that Spanish calls alway queue jump. Priority is absolute, so a p2 call will jump in front of all other lower-priority calls regardless of how long they have been there.
If you just want first-come-first-served, then that's what you should have by default.
Aaron

Selective Route Import/Export in MPLS VPN

Champs
I have multiple brach locations and 3 DC locations.DC locations host my internal applications , DC's also have central Internet breakout for the region. My requirement is to have full mesh MPLS-VPN but at same time brach location Internet access should be from nearest IDC in the region if nearest IDC is not availalbe it should go to second nearest DC for internet.I have decided which are primary and seconday DC for Internet breakout. How can this be achieved in MPLS-VPN scenario.Logically i feel , i have to announce specific LAN subnet and default route(with different BGP attribute like AS Path) from all 3 DCs. Spokes in the specific region should be able to import default route from primary DC and secondary DCs only using some route filter?
Regards
V

Hello Aaron,
the route example works for all routers except the one, where the VRF vpn2 is configured. What you can do for management purposes is either to connect through a neighbor router using packet leaking or configure another Loopback into VRF vpn2.
The last option (and my recommendation) is to establish another separate IP connection from your NMS to the MPLS core. Once VRFs are failing (for whatever reason, f.e. erroneously deleted) you might just not get connectivity to your backbone anymore to repair what went wrong.
So I would create an "interconnection router" with an interface in the VRF vpn2 and one interface in global IP routing table. This way you will still be able to access PEs, even if VRFs or MBGP is gone.
Hope this helps! Please rate all posts.
Regards, Martin

Wrong routing selection in production order creation via MILL_OC

Hi,
We are using the order combination functionality (MILL_OC)
We have a product with alternative routings.
Situation is as follows:
- Create 2 plan orders for the same material
- Execute MILL_OC
When I execute the MILL_OC transaction I get the request to choose the routing. If I select routing with groupcounter 2 for both orders, the combined order is created with routing X /groupcounter 1.
I also tried using production versions but the situation remains
even by forcing to "use always production version" = setting in the material master, I still get routing 1.
It seems the combined order takes always the first routing, Any selection is not possible
Did I miss a setting/customizing or is it a bug?
Any help would be appriciated
Regards
Johan

Hi Ayoub,
All the 4 routings are valid from Oct.2014 to 31.12.9999.
The Order date is from Apr.2015.
I've made another test with 2 routings created with ECN and the order chose one without asking me what to choose. I don't know the criteria used in this functionallity.
Thanks,
Caio.

Todo tab: Routes displayed when selecting the List View

Hi,
I have a question about the routes that appear on the workspace's "To do" list view, and how to perform validations when they are clicked.
I've created a process that starts with a form being created by a user. Then, it's validated by a sequence of other users. Each one sees a different set of routes. On one of the steps of the process, one of the routes requires the user to input a text.
The condition is checked on the click event of the AWS_SUBMIT button, where I've also put the text request. If the user is using the card view on the "To do" tab and clicks on the item, the form opens and, when the user submits it, all works as expected. However, if he has the list view and clicks once on the item, the route names appear on the bottom right of the workspace, and he's able to select them. As the form hasn't been opened, there's no control on the selected route, and the user is never asked to input the text. On the next step of the process, which depends on this text, the process gets stalled.
Is it possible to hide these routes on the workspace, disable the list view, or stop the submit if it hasn't been started without opening the form? I know you can customize the workspace, would this allow me to remove the route buttons?
The version we are using is LiveCycle ES 8.2.1.3.
Thank you

Is there any way to hide the submit button(green check mark) that appears on the task card when a user saves a form in their draft folder.
Users are bypassing the form validation by submitting a form this way. For instance, a user will fill out the form with values that do not pass validation. They will save the form in their drafts folder. The user will then close the form and navigate to their draft folder. Without opening the form again, they will click the green check box submit button and a form with invalid data will be submitted to the process.
This is LC 8.2.1.3.

Planned order not selecting BOM and Routing.

Dear All,
I am runing LTP, but for all simulative Planned order system is not selecting Routing and BOM.When i change it manually its selecting the correct BOM and Routing.
Please let me know what needed ....
Regards
Sathish

Dear,
First check the OPU5 setting for routing selection ID for your pant and order type?
Check setting of OPJM fo the selection ID linked application?
OS32 setting for alternative selection.
BOM is selected by the system based on the setting in MRP plant parameters(OPPQ) and in material master MRP view BOM explosion type. I. e based on the validity date, lot size. so on
Regards,
R.Brahmankar
Edited by: R Brahmankar on Apr 3, 2010 11:11 AM

Selecting appropriate Router & IOS for Gatekeeper

Hi All,
I managing the Video conference setup but I am struggling to find a appropriate IOS for Gatekeeper
I need some suggestion for selecting router series (Is 2620XM is ok?) and also the appropriate IOS?
Gateway is Tandberg
Planning for 8 video conference (8x256)

This URL should help you:
http://www.cisco.com/en/US/products/hw/routers/ps259/index.html
http://www.cisco.com/en/US/products/sw/voicesw/index.html

Order Fulfillment of LSP Service - multiple routing options - PR generation

Hi,
We are a logistics company and in the process of implementing SAP in our organsiation. We are referring to SAP Best Practices for LSP which suggest that we create a service type material master record called 'LSP Service' with variant enabled for capturing characteristics at the time of customer sales order.
Suppose I get a customer sales order for 'LSP Service' with variant info trucktype=6wheeler and consignor party - xyz, Mumbai and consignee party - pqr, guwahati.
Now, The Transport planning officer has to explore various route options for transporting goods from Mumbai to Guwahati which are
1. Mumbai to Guwahati direct
2. Mumbai to Delhi , Delhi to Guwahati
3. Mumbai to KAnpur, Kanpur to Guwahati
4. Mumbai to Indore, Indore to Guwahati
5. Mumbai to Nagpur , Nagpur to Guwahati
6, Mumbai to Nagpur, Nagpur to Kolkata, Kolkata to Guwahait
We execute the customers orders by hiring the vehicles from various vendors and our prices with the vendors are not fixed and decided on a day to day basis.
Based upon historical data, the system should propose the indicative costing for a given order for all the possible routes and transport planning officer should select the best option mostly on the basis of least cost. Now based upon the selected route, system should generate purchase requisitions.
For example, if Mumbai/Delhi/Guwahati route is selected, we would need to hire one vehicle from a vendor for Mumbai to Delhi, and another vehicle from another vendor for Delhi to Guwahati. There would be 2 purchase orders for hiring of vehicles required and for these 2 POs I'd want that 2 PRs should be generated one for mumbai to delhi, and another for delhi to guwahati.
Hope I've clarified my requirement. Shall appreciate your suggestions on best way to handle the scenario.

Hi,
06 076 is only for applicable only in case of material.
For Service and material both, use 06 400 as error "Materials/services for requisition & & already ordered with & &"
NOtes 786736
This may help u !
Regards,
Pardeep malik

You can bridge the Fios Quantum Gateway Router

Long story short. I could not figure out how to disable SIP on the Fios Gateway Router and some my Intercom Video Door station in use by my Control4 uses SIP. The router was causing conflicts and Control4 advised that SIP needs to be disabled on the router. Disabling SIP is a very common answer to people using IP based video conferencing or VOIP phones. That left me with 2 choices. Get the Fios Quantum Gateway to bridge and install my own router where SIP can be disabled, or get rid of Fios and use an ISP that does not require a combo "modem"/router. I didn't want to give up on Fios so easily. My installation was new and I am happy with the uptime and performance. I spent 2 days trying to get my Fios Quantum Gateway to Bridge. I am writing this up so that someone else doesn't have to live the pain I've lived. First up, after multple days of looking, their are limited instructions on getting the Fios Quantum Gateway router to bridge. The instructions you can find are for the Actiontec router. It's "almost" the same router but not 1:1. Most step by step guides say that the steps for the Actiontec will work for a FIos Quantum Gateway. That's not inaccurate, but isn't fully accurate either. Their are steps involved in the Acitontec instructions that do not apply to the Fios Quantum Gateway. First - this link is the baseline instructions I found that mostly work: http://www.dslreports.com/forum/r27666920-How-to-Make-Actiontec-MI424WR-Revision-I-Rev-I-a-Network All credit to the authors that came before me. I didn't discover these steps. I hijacked them and tested them with some revisions for a Fios Quantum Gateway router. I take not credit or responsbility for any action you take based on my post. It "works for me" and continues to work after 24 hours. My please note that I am using Coax/MoCa from the ONT to the Router and that Ethernet was not an option. I am going to repost the steps verbatim, but add some notes along the way where my experience was different in bold. I highly recommend you read the entire thing one time before starting with the step-by-step. You can replace the word Actiontech with Quantum Gateway in the below. Their are subtle differences in termonligy between the Acitontec and the Quantum. If you see a step in the guide and can not follow because your Quantum doesn't have the same display, you must find the nearest equivelement or ignore it entirelly. First get your Router and Actiontec set up like so: ONT -> Coax -> Actiontec Coax Port -> Actiontec LAN Port 1 -> My Selected Router WAN Port. Unplug the cable from the WAN Port, but keep it nearby. I was actually in LAN Port 1 on the Quantum Gateway but I don't think it will actually matter.
Now we need to obtain the WAN MAC address of each Router device.
For the Actiontec go to: Top Menu – Advanced – MAC Cloning – Set Mac of Device – Broadband (Coax). Here you should see the MAC Address, write this down on a paper or something. This is critical. You need to do this. Without the clone, I was unable to bridge. Note that I did not have to STAY cloned. I just had to clone until the lease expired even though I believe I had released the IP successfully. For your own router: You need to look this up yourself. The ASUS RT-N56U (w/ custom firmware) has a spot that just displays my WAN MAC address for me. I'm using an EdgeRouter from Unfi. Nobody can help you here except the forums for the router you are using because how you do this is different from router to router (generally speaking.)
Once you have both of these pieces of information, it is time to start.
1. Hardware Reset Actiontec Router I wouldn't do this. I didn't. I would actually save a copy of the configuration you have on the router before going any further, in case you have to hardware reset and restore your router.
2. Log into Router using [ admin/password ].
3. Change admin login info and set a different password. There should be a link on the side.
4. Top Menu – My Network – Side Menu – Network Connections – Network (Home/Office) – Settings – IP Address – Setto 192.168.x.1 where x is not used on your LAN – Apply
*NOTE*: Upon changing the default gateway IP of the Actiontec from 192.168.1.1 to 192.168.x.1, you will need to [ ipconfig /release ] and [ ipconfig /renew ] from Command Prompt, so your computer can quickly reconnect to the Actiontec. I changed this to 192.168.0.5 because my DHCP starts at 50. The Fios default is 192.168.0.1 and not .1.1.
5. Log back in to Actiontec router with new IP and new password you previously set.
6. Top Menu – Wireless Settings – Side Menu – Basic Security Settings – Wireless Off – Apply 7. Top Menu – Firewall Settings – Side Menu – General – Minimum – Apply
8. Top Menu – My Network – Side Menu – Network Connections – Advanced 9. Top Menu – My Network – Side Menu – Network Connections – Broadband (Coax) – Settings – Release – Apply
*NOTE*: If your IP address is not released properly you will need to wait 2 hours for your lease to expire or you’ll need to call Verizon Tech and get them to restart your system.
10. Broadband (Coax) – Settings – IP Distribution – Disable – Apply 11. Broadband (Coax) – Settings – DNS Server – No DNS Server – Apply 12. Broadband (Coax) – Settings – IP Address – No IP Address – Apply
13. Top Menu – My Network – Side Menu – Network Connections – Network (Home/Office) – Settings – IP Distribution – Disable – Apply 14. Network (Home/Office) – Settings – DNS Server – No DNS Server – Apply 15. Network (Home/Office) – Settings – UNcheck Box to Left of Wireless – Apply
*NOTE*: The old guide will tell you to uncheck the box to the left of “Coax” here. Unfortunately, in the Rev. I, Ethernet and Coax are stuck together as “Ethernet/Coax” and you can’t split the two. If you uncheck the box to the left of “Ethernet/Coax”, you will lose connection with the Actiontec Router and you will be forced to hard reset and start all over again.
16. Network (Home/Office) – Settings – Check Box to Left of Broadband (Coax) – Apply 17. Network (Home/Office) – Settings – Check STP Box to Right of Broadband(Coax) – Apply The Quantum Gateway didn't have an STP box to uncheck. I ignored this step with no adverse effects. 18. Network (Home/Office) – Settings – Network – Broadband Connection – Apply
19. Top Menu – Advanced – MAC Cloning – Set Mac of Device – Broadband (Coax) Using the information you gathered at the beginning: a. Set the WAN MAC of your selected Router to the MAC address listed here. b. Set the Address here to the WAN MAC of your selected router that will be connected to the Actiontec to avoid conflicts.
20. Plug the cable from Actiontec LAN Port 1 to your Routers WAN Port. Your router should be getting a WAN IP from Verizon. Test to make sure your WAN is established and that you can connect onto the internet, browse pages. Run a speed test to make sure everything is peachy.
*NOTE*: If your router did not get a WAN IP, you have a problem. I would recommend trying to re-trace your steps to see if you missed anything or just start all over and hard reset. :\
21. If everything worked out fine, connect a cable from your Router’s LAN Port 4 to the Actiontec LAN port 4. Again, I was using Port 1. But it shouldn't matter. I haven't tried other ports.
22. Power cycle your STB if you wish. You should see your STB show up in your DHCP list and it should be getting VOD/Widgets. This wasn't neccessary for me as I don't use Verizion TV service. Your millage may very. -V

NOTE: about bridging the Quantum Gateway G1100 Information about this is in DSLReports.com - Verizon FiOS FAQ. SEE: Verizon Online FiOS FAQ -> 3.2 Moca -> Can I get an ethernet connection in a room with only coax? There is a list of instructions for bridging routers, but the Verizon Quantum Gateway is not included there. Follow down the instructions and at step 2.5 here is added information that is not in the FAQ yet.
Instruction 2.5...
2.5a) The Verizon Quantum Gateway G1100 is slightly different from the Actiontec MI424wr. If your primary router's broadband connection is provisioned over coax, you need to disable the remote router's coax WAN connection to prevent it from attempting to become the primary router. If your broadband connection from the ONT to your primary router is ethernet, this step may be unnecessary.
Click on the MY NETWORK icon at the top.
Select NETWORK CONNECTIONS from the menu on the left.
If you’re using the Verizon Quantum Gateway G1100 as the remote router the Network Connections panel will show Broadband Connection (Ethernet/Coax) instead of Broadband Connection (coax).
Click on Broadband Connection (Ethernet/Coax)
The next panel displays Broadband Connection (Ethernet/Coax) Properties as its title. There is a Disable button at the top of the panel. There is also a Settings button at the bottom of the panel. You will come back to the Disable button.
Click on the Settings button.
The next panel displays the same title as the prior panel: Broadband Connection (Ethernet/Coax) Properties
In the middle of the panel next to the heading Enable/Disable Coax Link: there is a button labeled Disable.
Click on Disable.
Click on the Apply button at the bottom of the panel.
You will be taken to the Broadband Connection (Ethernet/Coax) Properties panel that you saw before.
At the top of this screen there is a button labeled Disable
Click on Disable
Click on the Apply button at the bottom of the screen.

Is it possible to sort or filter the switch routes under the switching tab?

In Teststand 3.1, is it possible to filter the switch routes under the switching tab in Action Properties? Since I have a large amount of routes that have been created in Switch Executive, how can I filter out some of the routes from the "Routes to Connect" section?

The TestStand Switching does not provide any inherent filtering capabilities. You do have a couple of options, however.
(1) NI-Switch provides the ability to set up route connections in
different groups. The Switch Page in TestStand allows you to
select Routing groups as well as specific Routes. It may be
easier for you to organize your Connections as groups and choose
between different groups.
(2) The Property page also allows you to build route connection
string and use that string for your Switching actions. It
may be easier for you to build a Route string and easily change that
string rather than selecting your routes everytime from within the
TestStand window.
Good Luck!
Tyler T.
Applications Engineer
National Instruments

WiFi Router help

HI,
We want to have WiFi router set up at home ,so it can be used on the Windows 8 laptop and Windows Lumia smartphone!
Do we need a selected router that would work with these device? If so, what are the specifications?
Solved!
Go to Solution.

Any decent router will be fine. make sure the router supports the same Wi-Fi modes as what you will be connecting with.
Click on the blue Star Icon below if my advice has helped you or press the 'Accept As Solution' link if I solved your problem..

CLOI_CHANGES_UPL_31 select routing

Similar Messages

Maybe you are looking for