Cloning of SAP R3

Hi,
In general, if I clone the whole SAP system from 1 hardware to another (same hardware sizing, same IP address, everthing the same), will the SAP start in the new hardware ? Is there any configuration that i need to change to get effect on the new hardware so that i can startup SAP without any error?
Regards
Lauran

The problem is, that you can not realy test this szenario without shutting down the productive instance.
Windows Domain controlers will detect that it is a backup of a node and will probably deactivate the computer account in the domain.
I should work, if you are removing the productive node from the domain, put the shadow node temporary in a work group and add it back again to the domain afterwards.
I would normally recommend to think about a MS Cluster (<a href="http://download.microsoft.com/download/7/6/f/76f3db2f-6f43-4624-bfde-ff731e3c1f96/GDClusters.doc">Geographically Dispersed Clusters</a>) for this kind of functionallity. I you include the database in this scenario or if you prefere a setup which uses a standby database is a different story.
regards
Peter

Similar Messages

  • Cannot Start Cloned SAP Instance

    Hi,
    We cloned a SAP Instance on VM from a production system. However, I am not able to start the cloned system.
    It's giving the error:
    Starting Database Instance...
    Error! Connection failed to node sapgrfpd for database GMP:
    database not found
    Opening Database...
    We've checked thru the mount points to ensure that all the access rights are granted correctly. I am able to start the x_server.

    [root@sapprod bin]# ./sdbverify
    Server Utilities 7.6.00.35 64 bit in /sapdb/programs
    check files... failed
    mode of /sapdb/programs/bin/x_server was modified
    mode of /sapdb/programs/pgm/starter/sdbstarter was modified
    owner of /sapdb/programs/pgm/starter/sdbstarter was modified
    check dependencies... ok
    package data is inconsistent
    DB Analyzer 7.6.00.35 64 bit in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    PCR 7300 7.3.00.55 in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    PCR 7301 7.3.01.18 in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    PCR 7500 7.5.00.24 64 bit in /sapdb/programs
    check files... ok
    check dependencies... ok
    check rte registration of package... ok
    package data is consistent
    SAP Utilities 7.6.00.35 64 bit in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    Base 7.6.00.35 64 bit in /sapdb/programs
    check files... failed
    mode of /sapdb/programs/bin/starter/sdbstarter was modified
    owner of /sapdb/programs/bin/starter/sdbstarter was modified
    mode of /sapdb/programs/bin/getdbroot was modified
    check dependencies... ok
    check rte registration of package... ok
    package data is inconsistent
    Redist Python 7.6.00.35 64 bit in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    JDBC 7.6.00.30 in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    Messages MSG 0.3951 in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    ODBC 7.6.00.35 64 bit in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    Database Kernel 7.6.00.35 64 bit in /sapdb/PRO/db
    check files... failed
    mode of /sapdb/PRO/db/pgm/dbmsrv was modified
    mode of /sapdb/PRO/db/pgm/starter/sdbstarter was modified
    owner of /sapdb/PRO/db/pgm/starter/sdbstarter was modified
    mode of /sapdb/PRO/db/pgm/dbmverifypw was modified
    owner of /sapdb/PRO/db/pgm/dbmverifypw was modified
    check dependencies... ok
    check rte registration of package... ok
    package data is inconsistent
    Loader 7.6.00.35 64 bit in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    SQLDBC 7.6.00.35 64 bit in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    SQLDBC 76 7.6.00.35 64 bit in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    Fastload API 7.6.00.35 64 bit in /sapdb/programs
    check files... ok
    check dependencies... ok
    package data is consistent
    VERIFICATION SUMMARY:
    INVALID PACKAGES:                   0
    VALID PACKAGES:                     16
    INCONSISTENT PACKAGES:              3
    TOTAL FILES:                        330
    MISSED FILES:                       0
    MODIFIED FILES:                     0
    FILES WITH MODIFIED PERMISSIONS:    7
    when I check the program in error ( like /sapdb/programs/bin/starter/sdbstarter ) seems like orphaned links when I ls -al them in my source system and normal files in my destination system.
    [root@sapprod bin]# mount | grep /sapdb
    /dev/sdc7 on /sapdb type ext3 (rw)
    [root@sapprod bin]# id sdb
    uid=1008(sdb) gid=503(sdba) groupes=503(sdba)
    [root@sapprod bin]# id proadm
    uid=1012(proadm) gid=125(sapsys) groupes=125(sapsys),501(sapinst),503(sdba)
    [root@sapprod bin]# ls -l /sapdb/programs/pgm/starter
    total 796
    -r-xx-  1 sdb sdba 803251 nov  6  2006 sdbstarter
    [root@sapprod bin]# ls -l /sapdb/programs/pgm
    total 15620
    -r-xr-xr-x  1 sdb sdba 5320170 nov  7  2006 lserver
    -r-xr-xr-x  1 sdb sdba  901356 nov  6  2006 maketi
    -r-x------  1 sdb sdba  856749 nov  6  2006 niserver
    -r-x------  1 sdb sdba  856845 nov  6  2006 nisslserver
    -r-xr-xr-x  1 sdb sdba 5522110 nov  6  2006 python
    -r-xr-xr-x  1 sdb sdba  752254 nov  7  2006 regupd
    -r-xr-xr-x  1 sdb sdba  732502 nov  6  2006 sqlping
    dr-x------  2 sdb sdba    4096 avr  9  2008 starter
    -r-x------  1 sdb sdba  944481 nov  6  2006 vserver
    [root@sapprod bin]# ls -l /sapdb/programs/bin
    total 44972
    -r-xr-xr-x  1 sdb sdba 2226673 nov  7  2006 dbanalyzer
    -r-xr-xr-x  1 sdb sdba 4373797 nov  7  2006 dbmcli
    -r-xr-xr-x  1 sdb sdba 1871802 nov  7  2006 dbmevtdisp
    -r-xr-xr-x  1 sdb sdba  924291 nov  7  2006 dbmgetf
    -r-xr-xr-x  1 sdb sdba 6546066 nov  7  2006 dbmrfc
    -r-xxx  1 sdb sdba  803328 nov  6  2006 getdbroot
    -r-xr-xr-x  1 sdb sdba 5448002 nov  7  2006 loadercli
    -r-xr-xr-x  1 sdb sdba  878958 nov  7  2006 protconv
    -r-xr-xr-x  1 sdb sdba   75135 nov  6  2006 sdbconfig
    -r-xr-xr-x  1 sdb sdba   25750 nov  7  2006 sdbinfo
    -r-xr-xr-x  1 sdb sdba   14128 nov  7  2006 SDBINST
    -r-xr-xr-x  1 sdb sdba   14128 nov  7  2006 sdbpack
    -r-xr-xr-x  1 sdb sdba   14096 nov  7  2006 sdbreg
    -r-xr-xr-x  1 sdb sdba   13872 nov  7  2006 sdbregview
    -r-xr-xr-x  1 sdb sdba   16520 nov  7  2006 SDBSETUP
    -r-xr-xr-x  1 sdb sdba   13872 nov  7  2006 sdbuninst
    -r-xr-xr-x  1 sdb sdba   13872 nov  7  2006 sdbverify
    -r-xr-xr-x  1 sdb sdba 2621305 nov  7  2006 sqlcli
    -r-xr-xr-x  1 sdb sdba 2551118 nov  7  2006 sqldbc_cons
    -r-xr-xr-x  1 sdb sdba   23575 nov  6  2006 sqlver
    -r-xr-xr-x  1 sdb sdba   23530 nov  6  2006 sqlwhat
    dr-x------  2 sdb sdba    4096 avr  9  2008 starter
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 sysmon
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_analys
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 xbackup
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_cons
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 xinstinfo
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_maketi
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_ping
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 xpu
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_python
    -r-xr-x--x  1 sdb sdba  966431 nov  7  2006 x_server
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_start
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_stop
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 xsysrc
    -r-xr-xr-x  1 sdb sdba  767938 nov  6  2006 xuser
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_wiz
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_wizard
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_wizstop
    -r-xr-xr-x  1 sdb sdba  966431 nov  7  2006 x_wiztrc
    [root@sapprod bin]# ls -l /sapdb/programs/bin/starter
    total 796
    -r-xx-  1 sdb sdba 803251 nov  6  2006 sdbstarter
    Thank you.
    Olivier.

  • Copy standard bapi to Zbapi in the same standard package

    Dear SAP,
    I wanted to copy a standard bapi into Zbapi. As soon as i do this it is asking for access key.
    Is it ok to use the access key and create??
    Is there any exit to do this ?
    Please help me in this regard.
    The Bapi name  /AFS/BAPI_SALESORD_CREATEFDATA
    from this Bapi, i want to create the ZBAPI.
    Regards,
    Arati

    If you put it in the same function group as the original, when new function modules are added to that function group, your BAPI will be affected - possibly disappear (depending on settings). it will certainly be an upgrade issue.
    If you put it in a SAP package, you are violating the principle of separating custom developments from SAP standard, but it's unlikely to cause issues.
    However, copying a BAPI (indeed any cloning of SAP standard code) is a bad idea. The reason is that the copy won't benefit from any notes or upgrades. If there's an error in the standard fixed by note application, you won't get it applied in the copy. Your copy will gradually become out of date. At some point it will probably break, and then you'll have to reclone the original, which can be quite difficult if it has changed radically.
    You should first try to find user exits (CMOD, BADI, explicit enhancement points), and implicit enhancement points, and finally direct modification of the original bapi.
    I repeat, cloning a SAP standard object is 99.9999% of the time the worst things to do. Far worse than a customer modification. Ignorant project managers, team leads etc. prefer clones because they don't need an object key. Don't be stupid. Do the right thing.

  • Copying a module pool program

    Hi,
    I am trying to copy a module pool program. I've followed the below steps.
    Go to SE80.
    Give the module pool program name.
    Click on COPY
    Give the target program name.
    Select all the check boxes even the INCLUDEs check box
    Click on COPY
    Give the include-name  target and click on copy.
    When I open the target program, it still has the include names of the original program
    and when I try to open the new include names given under target, these includes do not exist in SE38.
    Can anyone please guide me in copying the includes correctly?

    Hi,
    If you are cloning a SAP program this is a BAD idea.
    Regards.

  • Findout the program that is copied from Standard one

    Dear friends,
        I have a list of 300  Z programs. in that list few are copied from standard transactions. is there any way to find out those programs easily ?
    If any body knows, plz help me.
    Thanks in advance.

    Yes this can be achieved.
    First identify all the Z-objects and pass them to an Internal table.
    Looping all the Z-Reports.
    Use the Read Report(command) to read the entire source code.
    Scan the ABAP source code through
    SCAN ABAP-SOURCE itab1 ...TOKENS INTO itab2
    Each report which is copied or cloned has SAP standard report name in the Heading section.
    Eg: IF RSM04000_ALV is copied into ZRSM04000_ALV then
    verify the Repid in the Header section whether it is starting with Z or No. If No then the program is a copy.
    Hope this helps.
    Regards
    Vinayak

  • Why clone the default JRA configuration?

    When I follow the xMII install guide, I see a step called "Cloning the Def ault JRA Configuration".
    Why is this necessary?  I did not see this for a pure Java system install.
    Could you kindly explain?
    Thanks a lot!
    Regards.

    Hi,
    I have used JRA Cloning in SAP MII 12.1.6
    As per my knowledge when you want to use JRA action blocks in SAP MII Workbench under transaction.
    In JRA Start session action block you need to configure JRA Connector Name which contains following info.
    Than you need to configure clone of default JRA in which we will pass all SAP system (to which you want to communicate)details like
    SAPClient
    The SAP ECC client number to which you want to connect
    UserName
    The SAP ECC-defined user for the communication
    Password
    The SAP ECC-defined password for your user name
    Language
    The logon language for the user
    ServerName
    The SAP ECC server URL as it resolves on your network (Fully Qualified)
    PortNumber
    The SAP ECC-defined system number to which you are connecting
    just for understaning as we pass different parameter in JCO action blocks like  client, username, password etc..
    Hope this help
    Regards,
    Manoj Bilthare

  • SAP LVM 2.0 Provisioned/Cloned Virtual Hosts

    Hi All,
    Could you please let me know how to define a virtual host in SAP LVM 2.0.
    I have configured Virtualization Manager in SAP LVM 2.0 and added the virtual host to SAP LVM 2.0,  But I am not able to see configured virtual host cloning screen.
    Kindly suggest me on this.
    Thanks and Regards,
    Prasad

    Hi Michael,
    Thank you, we have configured virtualization Manager in LVM and host agent is also installed on virtual host.
    Thanks and Regards,
    Prasad

  • Basis work for SAP system copy using DB2 cloning tool

    My company is using the DB2 cloning tool, formerly from MainStar. Our DBAs have used this tool to create a clone of a technical sandbox (ST1) to another DB2 instance (SZ1).
    I am reading through the System Copy for SAP Systems Based on SAP NetWeaver 2004s SR2 ABAP+Java guide and trying to follow the steps.
    As information, our application servers are currently running on zLinux and I am trying to do a system copy of an HA ABAP+Java SID.
    Since we have used the cloning tool, which I would equate to a homogeneous system copy using database specific tools, the guide looks like it says I can skip the Export Preparation and Table Splitting Preparation steps. The only other step for the source system is the Database and Central Instance Export.
    When I execute this step, it creates a dump of the database. This seems useless as we already have a cloned copy of the database.
    Does anyone have the list of Basis tasks for a system copy when the DB2 cloning tool is used?
    Brian

    Nevermind. If someone sets:
    rdisp/j2ee_start = 0
    in an ABAP+Java system, sapinst behaves strangely during the system export and does not give the option to only dump the filesystem. Bug?
    Brian

  • SAP LVM Cloning error with Listener

    Hi All,
    Our Cloning operation has been failed with following error message.
    "Failed to start Oracle Listener: TNS-01106: Listener using the listener name LISTENER has already been started"
    When I checked listener status on target vm , listener is still pointing to source system hostname.
    I kinldy request you to suggest me on the same.
    Thanks and Regards,
    Prasad

    Hello Julia,
    to do this, you need to use the custom provisioning procedure. this will replace the cloning function of LVM. Please take a detailed look at the customization blog i created.SAP Landscape Virtualization Management (LVM) Overview of Customization Options
    basically you have to create your script, use it in a provider definition and use this provider definition as one of the custom prov. steps. then you need to enable your system fro custom prov. in the settings of the source system. Also keep in mind that you can only refresh a system after you have done an successful initial copy
    You should involve SAP consulting int his project, since it is not easy to achieve this on your own.
    Kind Regards
    Michael

  • Cloning a Standard SAP Query

    Hi guys,
    I need to modify the transaction ME80FN, which is a SAP Query. I want to make a clone of the SAP Query, if isn't possible to modify the program AQZZ/SAPQUERY/MEME80FN========. I haven't deal with SAP Queries before. Can anyone please tell me the steps to accomplish this?
    Thanks,
    Raulie

    Haven't worked with queries, but I think you should be able to make a copy on SQ01...anyway, querys are still ABAP programs, so you could the copy the code of AQZZ/SAPQUERY/MEME80FN======== paste it on a Z program and make the needed modifications...
    Greetings,
    Blag.

  • Cloning SAP instance on Windows

    Hi - We have SAP on Windows server and our Database is on Unix. We want to make clone of this whole environment. From DB perspective it is easy - we can copy the database to another Unix Server. What do we have to do from Windows/SAP side?
    Can we just copy the binaries to another Windows server or do we need to install SAP from scratch?

    From Windows/SAP perspective you can do it in two ways either running the SAP Inst or the folder copy option. As per me the folder copy option is easier than running SAP Inst. The steps is as follows.
    1. Copy the //server1/<Drive>/usr/sap/<SID> folder to //server2/<Drive>/usr/sap/<SID>
    2. Determine the new Instance Number.
    3. Rename folder //server2/<Drive>/usr/sap/<SID>/DVBMGxx....where xx is the new Instance no.
    4. Go to the profile directory and change the following entries.
    a. Replace all entries of the old database server with new database server.
    b. Replace all entries of the old SAP binaries server with new SAP binaries server.
    c. Replace all old instance number to new Instance number (if old instance no is 00 then change all parameter which are ended with old instance no. i.e. _00)
    5. Rename profile files as per new instance no.
    6. Run program SAPSTARTSRV.EXE to setup new SAP Services and MMC.
    Let me know if you have any concern.
    Thanks,
    SK

  • New sap user creation

    Hi All SAP experts,
    My company has implemented 2 Systems SAP Landscape with one development and one production server which are running on R/3 Enterprise 4.7 (Kernel Release 6.20) with Microsoft SQL 2000 as database server.
    I have the following questions regarding new sap user creation by using user copy function.
    1.When I request to create new SAP User by using user copy function ,should I just create the user acct in DEV and transport it to PROD System? If yes, how could I do that?
    2.When I request to create new SAP User by using user copy function, can I just create it on PROD System only? If yes, what is the impact?
    3.When using User copy function to create new user acct, should I select all parts (like adress ,defaults,reference user, user groups.....) of the existing user to be cloned to new user acct?
    Thanks.
    Leon

    Hi Leon,
    Answer to your questions in their respective order:
    1. You can create user in DEV and then make remote client copy to PRD system using scc9 t-code. Here you can choose user accounts and authorizations for the copy. ( Rem: Data will be overwritten in target system when copied).
    You can also use client export/import(scc8/scc7)
    But, When you do the client import from the exported files using STMS,you will have to select only one of the transport requests and then STMS automatically selects the other requests for you.
    Then it will show you the different transport requests that you have created during your export, the client copy profile and the target system and client. The customizing and application data is deleted in the target client before copying for all profiles except SAP_USER. This is technically unavoidable (and hence the data will be overwritten).
    So if you can afford overwritting of user data in target client , you can go with the above procedure.
    2. Using  user copy in su01, you can copy one user to another user only in that client and is confined to that system only. So yes, If you want 2 or more users to have same authorizations, profiles ,etc etc.. you can choose this in PROD system.
    3. It depends.. If you want user to be in same group, then you can choose user groups. If you want them to have same authorizations , you can choose roles and profiles... If you want them to have same company address and others,... you can select address.. and so on.
    Also below link provides required steps in case you choose local/ remote client copy:
    http://www.sap-basis-abap.com/bc/client-copy-by-using-scc8-and-scc7.htm
    Hope this helps...
    Thanks,
    Ajith
    Edited by: Ajith Kamath on Oct 20, 2009 8:28 AM

  • DETERMINE_PROFILES error on cloned system

    Hi,
    To get timings on an EHPI upgrade to EHP4, we cloned a dual stack system.  ABAP and JAVA are both running without any apparent problems on the cloned system.  During the EHPI upgrade soon after starting the JAVA portion of the upgrade, however, it hangs in DETERMINE_PROFILES looking for a profile for the original system.  I've reviewed the following without finding any references to the old SID or the old hostname.
    /etc/hosts
    /etc/services
    /usr/sap/sapservices
    /sapmnt/<SID>/profile ( and no, there aren't any extraneous profiles nor is msgservu or enservu specified)
    /usr/sap/<SID>/SYS/profile
    tnsnames.ora
    environmental settings for sidadm and orasid
    configtool ( I also exported the cluster information, unzipped everything, and grepped )
    Anyone have any ideas on where else to look?
    Thanks,
    Russ

    Hi Russ,
    had a nose round SDN probably like you, but did you find this ?
    Last entry..
    Error while detecting start profile for instance with ID _u.
    Mark

  • System requirements for BO Enterprise XI 3.0 with 3 cloned webi services

    Helllo,
    I'm wondering what the system requirements would be for a server to host a BO Enterprise system (XI 3.0) if it is connected to a SAP BW system.
    The system should be able to cope with around 150 to 200 calls/requests maximum at a time.
    The users log in into SAP and launches a request via an SAP screen with behind that an URL request that is constructed based on a guest account (max 200 requests at the time) for BO. Because it is always the same account (Guest) that is used over and over again I'm wondering what kind of additional requirements the system should support.
    We did some stresstesting with 120 simultaneous users. Even with 3 cloned web intelligence processing servers it blocked several times.
    For the moment it is running on following hardware specifications:
    HRBOXI (Dell PowerEdge 2950 (Servicetag: GMZ834J))
    Memory: 8 memory slots available on motherboard of which 2 are used (each is  2GB) Total available memory at this moment is 4GB.
    CPU: 2 x Intel Xeon E5420 (quad core). There are 2 CPU sockets on the motherboard that are in use.
    Disks:  2 x 146GB (15K) SAS
    On that there is a 32bit operating system in use. We would like to start with upgrading that to 64 bit OS.
    Can someone tell me if this machine is suitable for production purposes for BO Enterprise linked to an SAP BW on mainly HR-data? I mean by that does this machine has enough processors to be able to cope with 3 cloned webintelligence services at a time. And also enough RAM memory?
    Many thanks Thierry Renaer

    not of use anymore

  • SAP Netweaver 7.02 installation problem, "Start Instance" not possible??

    Hello,
    i need help with my "new" Problem during installation of SAP Netweaver, everything is ok until "Phase 21 of 24'" is reached,
    here should the instance started, i receive this error:
    "An error occurred while processing option SAP NetWeaver 7.0 including Enhancement Package 2 > SAP Application Server ABAP > MaxDB > Central System > Central System( Last error reported by the step :ABAP processes of instance NSP/DVEBMGS00 [ABAP: STARTING] did not start after 10:10 minutes. Giving up.)."
    I can see in the SAPmmc that msg_server.exe ist started and is green, but disp+work.exe is yellow and have a status:
    "Running but dialog queue stand still."
    That all make me confuse, why is there a such big difference in 32 and 64bit installtion?
    I have this problem only on windows 7 64bit. on 32bit windows i nave never problems with installation.
    Can anyone help me here please?
    If need more information i can put here some logfiles?
    Thanks for any help
    Mirso

    Here is the next file dew_w0:
    trc file: "dev_w0", trc level: 1, release: "720"
    *  ACTIVE TRACE LEVEL           1
    *  ACTIVE TRACE COMPONENTS      all, MJ
    M sysno      00
    M sid        NSP
    M systemid   562 (PC with Windows NT)
    M relno      7200
    M patchlevel 0
    M patchno    46
    M intno      20020600
    M make       multithreaded, Unicode, 64 bit, optimized
    M profile    \\BIG\sapmnt\NSP\SYS\profile\NSP_DVEBMGS00_BIG
    M pid        6896
    M
    M 
    M Thu Aug 07 20:23:20 2014
    M  kernel runs with dp version 125000(ext=118000) (@(#) DPLIB-INT-VERSION-125000-UC)
    M  length of sys_adm_ext is 588 bytes
    M  ***LOG Q0Q=> tskh_init, WPStart (Workp. 0 6896) [dpxxdisp.c   1314]
    I  MtxInit: 30000 0 0
    M  DpSysAdmExtCreate: ABAP is active
    M  DpSysAdmExtCreate: VMC (JAVA VM in WP) is active
    M  DpIPCInit2: read dp-profile-values from sys_adm_ext
    M  DpShMCreate: sizeof(wp_adm)        31696    (2264)
    M  DpShMCreate: sizeof(tm_adm)        5517056    (27448)
    M  DpShMCreate: sizeof(wp_ca_adm)        64000    (64)
    M  DpShMCreate: sizeof(appc_ca_adm)    64000    (64)
    M  DpCommTableSize: max/headSize/ftSize/tableSize=500/16/584064/584080
    M  DpShMCreate: sizeof(comm_adm)        584080    (1144)
    M  DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=512/48/65600/90416/156064
    M  DpShMCreate: sizeof(slock_adm)        156064    (104)
    M  DpFileTableSize: max/headSize/ftSize/tableSize=2800/16/268864/268880
    M  DpShMCreate: sizeof(file_adm)        268880    (80)
    M  DpShMCreate: sizeof(vmc_adm)        30128    (2152)
    M  DpShMCreate: sizeof(wall_adm)        (41664/36752/64/192)
    M  DpShMCreate: sizeof(gw_adm)    48
    M  DpShMCreate: sizeof(j2ee_adm)    3936
    M  DpShMCreate: SHM_DP_ADM_KEY        (addr: 000000000DD90050, size: 6812336)
    M  DpShMCreate: allocated sys_adm at 000000000DD90060
    M  DpShMCreate: allocated wp_adm_list at 000000000DD93030
    M  DpShMCreate: allocated wp_adm at 000000000DD93220
    M  DpShMCreate: allocated tm_adm_list at 000000000DD9AE00
    M  DpShMCreate: allocated tm_adm at 000000000DD9AE50
    M  DpShMCreate: allocated wp_ca_adm at 000000000E2DDD60
    M  DpShMCreate: allocated appc_ca_adm at 000000000E2ED770
    M  DpShMCreate: allocated comm_adm at 000000000E2FD180
    M  DpShMCreate: allocated slock_adm at 000000000E38BB20
    M  DpShMCreate: allocated file_adm at 000000000E3B1CD0
    M  DpShMCreate: allocated vmc_adm_list at 000000000E3F3730
    M  DpShMCreate: allocated vmc_adm at 000000000E3F37E0
    M  DpShMCreate: allocated gw_adm at 000000000E3FADA0
    M  DpShMCreate: allocated j2ee_adm at 000000000E3FADE0
    M  DpShMCreate: allocated ca_info at 000000000E3FBD50
    M  DpShMCreate: allocated wall_adm at 000000000E3FBD70
    M  DpCommAttachTable: attached comm table (header=000000000E2FD180/ft=000000000E2FD190)
    M  DpSesCreateTable: attached session table at 00000000029A0050 (len=161328)
    M  DpRqQInit: use protect_queue / slots_per_queue 0 / 2001 from sys_adm
    M  rdisp/queue_size_check_value :  -> on,50,30,40,500,50,500,80
    X  EmInit: MmSetImplementation( 2 ).
    X  MM global diagnostic options set: 0
    X  <ES> client 0 initializing ....
    X  Using implementation view
    X  <EsNT> Using memory model view.
    M  <EsNT> Memory Reset disabled as NT default
    X  ES initialized.
    M  DpVmcSetActive: set vmc state DP_VMC_ENABLED
    M  DpVmcSetActive: set vmc state DP_VMC_ACTIVE
    M  DpVmcInit2: o.k.
    M 
    M Thu Aug 07 20:23:21 2014
    M  ThStart: taskhandler started
    M  ThInit: initializing DIA work process W0
    M 
    M Thu Aug 07 20:23:23 2014
    M  ThInit: running on host BIG
    M 
    M Thu Aug 07 20:23:24 2014
    M  calling db_connect ...
    B  create_con (con_name=R/3)
    B  Loading DB library 'C:\usr\sap\NSP\DVEBMGS00\exe\dbsdbslib.dll' ...
    B  Library 'C:\usr\sap\NSP\DVEBMGS00\exe\dbsdbslib.dll' loaded
    B  Version of 'C:\usr\sap\NSP\DVEBMGS00\exe\dbsdbslib.dll' is "720.00", patchlevel (0.45)
    B  New connection 0 created
    C 
    C  DBSDBSLIB : version 720.00, patch 0.045 (Make PL 0.46)
    C  MAXDB shared library (dbsdbslib) patchlevels (last 10)
    C    (0.045) Unknown primary key (note 1459400)
    C    (0.039) Define your own command buffersize (note 1340617)
    C    (0.031) Dbm commands support added (note 1420733)
    C    (0.027) Count of records for bulk insert optimized (note 1340617)
    C    (0.021) Connect with special xuser key (note 1390464)
    C    (0.018) Error handling for external update statistics changed (note 1340617)
    C    (0.018) Dbsl procedure to update datasource information (note 1340617)
    C    (0.015) Special describe handling on MaxDB systemtables (note 1382175)
    C    (0.013) Possibility to disable UPSERT statements (note 1340617)
    C    (0.013) Check for external update statistics changed (note 1340617)
    C 
    C 
    C  Loading SQLDBC client runtime ...
    C 
    C Thu Aug 07 20:23:25 2014
    C  SQLDBC Module  : C:\sapdb\clients\NSP\pgm\libSQLDBC77.dll
    C  SQLDBC SDK     : SQLDBC.H  7.7.4    BUILD 009-123-173-450
    C  SQLDBC Runtime : libSQLDBC 7.8.1    BUILD 014-121-233-288
    C  SQLDBC client runtime is MaxDB 7.8.1.014 CL 233288
    C  SQLDBC supports new DECIMAL interface : 1
    C  SQLDBC supports VARIABLE INPUT data   : 1
    C  SQLDBC supports VARIABLE OUTPUT data  : 1
    C  SQLDBC supports Multiple Streams      : 1
    C  SQLDBC supports LOB LOCATOR KEEPALIVE : 1
    C  SQLDBC supports LOB LOCATOR COPY      : 1
    C  SQLDBC supports BULK SELECT with LOBS : 1
    C  INFO : SQLOPT= -I 0 -t 0 -S SAPR3
    C  Try to connect (DEFAULT) on connection 0 ...
    C  Attach to SAP DB : Kernel    7.8.01   Build 014-121-233-288
    C  Database release is SAP DB 7.8.01.014
    C  INFO : Database 'NSP' instance is running on 'minisap'
    C  DB supports UPSERT SQL syntax : 1
    C  DB supports new EXPAND syntax : 1
    C  DB supports LOB locators      : 1
    C  DB uses MVCC support          : 0
    C  DB max. input host variables  : 2000
    C  INFO : SAP DB Packet_Size = 131072
    C  INFO : SAP DB Min_Reply_Size = 4096
    C  INFO : SAP DB Comm_Size = 126976
    C  INFO : DBSL buffer size = 126976
    C  INFO : SAP DB MaxLocks = 300000
    C  INFO : Connect to DB as 'SAPNSP'
    C  Command info enabled
    C  Now I'm connected to MaxDB
    C  00: minisap-NSP, since=20140807202325, ABAP= <unknown> (0)
    B  Connection 0 opened (DBSL handle 0)
    B  Wp  Hdl ConName          ConId     ConState     TX  BC  HC  PRM RCT FRC TIM MAX OPT Date     Time   DBHost           Program                                
    B  000 000 R/3              000000000 ACTIVE       NO  NO  NO  YES NO  NO  000 255 255 20140807 202324 minisap                                                 
    C  INFO : SAP RELEASE (DB) = 702
    M  ThInit: db_connect o.k.
    M  ICT: exclude compression: *.zip,*.rar,*.arj,*.z,*.gz,*.tar,*.lzh,*.cab,*.hqx,*.ace,*.jar,*.ear,*.war,*.css,*.pdf,*.gzip,*.uue,*.bz2,*.iso,*.sda,*.sar,*.gif,*.png,*.swc,*.swf
    M  vmcj/sgc_options: switch on template cleanup before cloning
    M  vmcj/sgc_options: switch off delayed session cleanup during shared gc
    M  ThVmcInitWaitForVm: th_maxWaitForVmTime=30
    M  ThVmcInitMaxErrCount: th_max_error_count=5
    I  MtxInit: 0 0 0
    M  SHM_PRES_BUF            (addr: 0000000014830050, size: 4400000)
    M  SHM_ROLL_AREA        (addr: 000007FEC3B40050, size: 268435456)
    M  SHM_PAGING_AREA        (addr: 0000000014C70050, size: 134217728)
    M  SHM_ROLL_ADM            (addr: 000000001CC80050, size: 2767448)
    M  SHM_PAGING_ADM        (addr: 0000000002E30050, size: 525344)
    M  ThCreateNoBuffer        allocated 548152 bytes for 1000 entries at 0000000002F70050
    M  ThCreateNoBuffer        index size: 3000 elems
    M  ThCreateVBAdm        allocated 30976 bytes (50 server) at 0000000002B00050
    X  EmInit: MmSetImplementation( 2 ).
    X  MM global diagnostic options set: 0
    X  <ES> client 0 initializing ....
    X  Using implementation view
    X  ES initialized.
    B  db_con_shm_ini:  WP_ID = 0, WP_CNT = 14, CON_ID = -1
    B  dbtbxbuf: Buffer TABL  (addr: 00000000208D0160, size: 30000000, end: 000000002256C4E0)
    B  dbtbxbuf: Buffer TABLP (addr: 0000000022570160, size: 10240000, end: 0000000022F34160)
    B  dbexpbuf: Buffer EIBUF (addr: 0000000022F40170, size: 4194304, end: 0000000023340170)
    B  dbexpbuf: Buffer ESM   (addr: 0000000023350170, size: 4194304, end: 0000000023750170)
    B  dbexpbuf: Buffer CUA   (addr: 0000000023760170, size: 3072000, end: 0000000023A4E170)
    B  dbexpbuf: Buffer OTR   (addr: 0000000023A50170, size: 4194304, end: 0000000023E50170)
    I  MPI: dynamic quotas disabled.
    I  MPI init: pipes=4000 buffers=1279 reserved=383 quota=10%
    M  CCMS uses Shared Memory Key 73 for monitoring.
    M  CCMS: SemInMgt: Semaphore Management initialized by AlAttachShm_Doublestack.
    M  CCMS: SemInit: Semaphore 38 initialized by AlAttachShm_Doublestack.
    M  CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
    S  *** init spool environment
    S  TSPEVJOB updates outside critical section: event_update_nocsec = 1
    S  initialize debug system
    T  Stack direction is downwards.
    T  debug control: prepare exclude for printer trace
    T  new memory block 00000000133FFCE0
    S  spool kernel/ddic check: Ok
    S  using table TSP02FX for frontend printing
    S  1 spool work process(es) found
    S  frontend print via spool service enabled
    S  printer list size is 150
    S  printer type list size is 50
    S  queue size (profile)   = 300
    S  hostspool list size = 3000
    S  option list size is 30
    S      found processing queue enabled
    S  found spool memory service RSPO-RCLOCKS at 000000002D1500D0
    S  doing lock recovery
    S  setting server cache root
    S  found spool memory service RSPO-SERVERCACHE at 000000002D150530
    S    using messages for server info
    S  size of spec char cache entry: 297032 bytes (timeout 100 sec)
    S  size of open spool request entry: 2512 bytes
    S  immediate print option for implicitely closed spool requests is disabled
    A  ***GENER* Trace switched on ***
    A 
    A  ---PXA-------------------------------------------
    A  PXA INITIALIZATION
    A  System page size: 4kb, total admin_size: 22076kb, dir_size: 21360kb.
    A  Attached to PXA (address 000007FED3B70050, size 300000K, 1 fragments of 277924K )
    A  PXA allocated (address 000007FED3B70050, size 300000K)
    A  *** WARNING: INTERNAL_KERNEL_VERSION of message server
    A               unknown yet.
    A  abap/pxa = shared protect gen_remote
    A  PXA: checking structure sizes: 752|264|16
    A  PXA INITIALIZATION FINISHED
    A  ---PXA-------------------------------------------
    A 
    A  ABAP ShmAdm attached (addr=000007FFDF0EE000 leng=20955136 end=000007FFE04EA000)
    A  >> Shm MMADM area (addr=000007FFDF5E2970 leng=242368 end=000007FFDF61DC30)
    A  >> Shm MMDAT area (addr=000007FFDF61E000 leng=15511552 end=000007FFE04E9000)
    A  RFC Destination> destination BIG_NSP_00 host BIG system NSP systnr 0 (BIG_NSP_00)
    A  RFC Options> H=BIG,S=00,d=2,
    A  RFC FRFC> fallback activ but this is not a central instance.
    A   
    A  RFC rfc/signon_error_log = -1
    A  RFC rfc/dump_connection_info = 0
    A  RFC rfc/dump_client_info = 0
    A  RFC rfc/cp_convert/ignore_error = 1
    A  RFC rfc/cp_convert/conversion_char = 23
    A  RFC rfc/wan_compress/threshold = 251
    A  RFC rfc/recorder_pcs not set, use defaule value: 2
    A  RFC rfc/delta_trc_level not set, use default value: 0
    A  RFC rfc/no_uuid_check not set, use default value: 0
    B  dbtran INFO (init_connection '<DEFAULT>' [ADABAS D:720.00]):
    B   max_blocking_factor =  10,  max_in_blocking_factor      = 127,
    B   min_blocking_factor =  10,  min_in_blocking_factor      = 127,
    B   prefer_union_all    =   1,  prefer_join                 =   0,
    B   prefer_fix_blocking =   0,  prefer_in_itab_opt          =   1,
    B   convert AVG         =   0,  alias table FUPD            =   0,
    B   escape_as_literal   =   0,                                  
    B   select *            =0x0f,  character encoding          = STD / <none>:-,
    B   use_hints           = abap->1, dbif->0x1, upto->4294967295
    M  ThrCreateShObjects        allocated 29124 bytes at 0000000002B20050
    N  SsfSapSecin: putenv(SECUDIR=C:\usr\sap\NSP\DVEBMGS00\sec): ok
    N 
    N  =================================================
    N  === SSF INITIALIZATION:
    N  ===...SSF Security Toolkit name SAPSECULIB .
    N  ===...SSF library is C:\usr\sap\NSP\DVEBMGS00\exe\sapsecu.dll .
    N  ===...SSF default hash algorithm is SHA1 .
    N  ===...SSF default symmetric encryption algorithm is DES-CBC .
    N  ===...SECUDIR="C:\usr\sap\NSP\DVEBMGS00\sec"
    N  ===...loading of Security Toolkit successfully completed.
    N  ===   SAPSECULIB Version 5.4.28M-6
    N  =================================================
    N 
    N Thu Aug 07 20:23:26 2014
    N  MskiInitLogonTicketCacheHandle: Logon Ticket cache pointer retrieved from shared memory.
    N  MskiInitLogonTicketCacheHandle: Workprocess runs with Logon Ticket cache.
    M  JrfcVmcRegister in process-driver OK
    M  JrfcVmcRegisterNativesDriver o.k.
    W  =================================================
    W  === ipl_Init() called
    W    ITS Plugin: Path dw_gui
    W    ITS Plugin: Description ITS Plugin - ITS rendering DLL
    W    ITS Plugin: sizeof(SAP_UC) 2
    W    ITS Plugin: Release: 720, [7200.0.46.20020600]
    W    ITS Plugin: Int.version, [33]
    W    ITS Plugin: Feature set: [23]
    W    ===... Calling itsp_Init in external dll ===>
    W  === ipl_Init() returns 0, ITSPE_OK: OK
    W  =================================================
    N  SignInit: successfully obtained handle for Security Context cache
    N  VSI: WP init in ABAP VM completed with rc=0
    E  Enqueue Info: rdisp/wp_no_enq=1, rdisp/enqname=<empty>, assume BIG_NSP_00
    E  Enqueue Info: enque/use_pfclock2 = FALSE
    E  Enqueue Info: row condense enabled
    E  Enqueue Info: enque/use_pfclock2 = FALSE
    E  Replication is disabled
    E  EnqCcInitialize: local lock table initialization o.k.
    E  EnqId_SuppressIpc: local EnqId initialization o.k.
    E  EnqCcInitialize: local enqueue client init o.k.
    M 
    M Thu Aug 07 20:23:27 2014
    M  ***LOG Q0I=> NiPConnect2: 127.0.0.1:65000: connect (10061: WSAECONNREFUSED: Connection refused) [nixxi.cpp 3271]
    M  *** ERROR => NiPConnect2: SiPeekPendConn failed for hdl 1/sock 1340
        (SI_ECONN_REFUSE/10061; I4; ST; 127.0.0.1:65000) [nixxi.cpp    3271]
    M  *** ERROR => IcmConnect: NiConnect to localhost:65000,-1 (rc=-10) [icxxext.c    182]
    M  *** ERROR => ThPlgConnectToIcm: IcmConnect failed (-10) [thxxplg.c    5120]
    M  in_ThErrHandle: 1
    M  *** ERROR => ThStart: connect to icman (step 1, th_errno 2, action 3, level 1) [thxxhead.c   11087]
    M 
    M  Info for wp 0
    M 
    M    pid = 6896
    M    severity = 0
    M    status = 0
    M    stat = WP_NEW
    M    waiting_for = NO_WAITING
    M    reqtype = DP_RQ_DIAWP
    M    act_reqtype = NO_REQTYPE
    M    req.req_info =
    M    req.tid = -1
    M    req.uid = 4294967295
    M    req.mode = 255
    M    req.len = -1
    M    req.rq_id = 65535
    M    req.rq_source =
    M    req.vm = no VM
    M    last_tid = 0
    M    last_uid = 0
    M    last_mode = 0
    M    act_cs_count = 0
    M    csTrack = 0
    M    csTrackRwExcl = 0
    M    csTrackRwShrd = 0
    M    mode_cleaned_counter = 0
    M    control_flag = 0
    M    int_checked_resource(RFC) = 0
    M    ext_checked_resource(RFC) = 0
    M    int_checked_resource(HTTP) = 0
    M    ext_checked_resource(HTTP) = 0
    M    report = >                                        <
    M    action = 0
    M    tab_name = >                              <
    M    attachedVm = no VM
    M 
    M  ThIErrHandle: current request:
    M 
    M  -IN-- sender_id ?                 tid  -1    wp_ca_blk   -1      wp_id -1
    M  -IN-- action    -                 uid  -1    appc_ca_blk -1      type  -   
    M  -IN-- new_stat  NO_CHANGE         mode 255   len         -1      rq_id -1
    M  PfStatDisconnect: disconnect statistics
    M  Entering TH_CALLHOOKS
    M  ThCallHooks: call hook >TrThHookFunc< for event BEFORE_DUMP
    M  TrThHookFunc: called for WP dump
    M  ThCallHooks: hook >TrThHookFunc< o.k.
    M  ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
    M  ThrSaveSPAFields: save spa fields
    M  ThrSaveSPAFields: not an update task, no update info saved
    M  ThrSaveSPAFields: not a batch task, field zttabtckey not saved
    M  ThCallHooks: hook >ThrSaveSPAFields< o.k.
    M  ThCallHooks: call hook >ThrBtcCallLgCl< for event BEFORE_DUMP
    M  ThCallHooks: hook >ThrBtcCallLgCl< o.k.
    M  ThIErrHandle: entering ThSetStatError
    M  ThIErrHandle: do not call ThrCoreInfo (no_core_info=0, in_dynp_env=0)
    M  Entering ThReadDetachMode
    M  call ThrShutDown (1)...
    M  ***LOG Q02=> wp_halt, WPStop (Workp. 0 6896) [dpnttool.c   339]
    trc file: "dev_w0", trc level: 1, release: "720"
    *  ACTIVE TRACE LEVEL           1
    *  ACTIVE TRACE COMPONENTS      all, MJ
    M sysno      00
    M sid        NSP
    M systemid   562 (PC with Windows NT)
    M relno      7200
    M patchlevel 0
    M patchno    46
    M intno      20020600
    M make       multithreaded, Unicode, 64 bit, optimized
    M profile    \\BIG\sapmnt\NSP\SYS\profile\NSP_DVEBMGS00_BIG
    M pid        7620
    M
    M 
    M Thu Aug 07 20:28:43 2014
    M  kernel runs with dp version 125000(ext=118000) (@(#) DPLIB-INT-VERSION-125000-UC)
    M  length of sys_adm_ext is 588 bytes
    M  ***LOG Q0Q=> tskh_init, WPStart (Workp. 0 7620) [dpxxdisp.c   1314]
    I  MtxInit: 30000 0 0
    M  DpSysAdmExtCreate: ABAP is active
    M  DpSysAdmExtCreate: VMC (JAVA VM in WP) is active
    M  DpIPCInit2: read dp-profile-values from sys_adm_ext
    M  DpShMCreate: sizeof(wp_adm)        31696    (2264)
    M  DpShMCreate: sizeof(tm_adm)        5517056    (27448)
    M  DpShMCreate: sizeof(wp_ca_adm)        64000    (64)
    M  DpShMCreate: sizeof(appc_ca_adm)    64000    (64)
    M  DpCommTableSize: max/headSize/ftSize/tableSize=500/16/584064/584080
    M  DpShMCreate: sizeof(comm_adm)        584080    (1144)
    M  DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=512/48/65600/90416/156064
    M  DpShMCreate: sizeof(slock_adm)        156064    (104)
    M  DpFileTableSize: max/headSize/ftSize/tableSize=2800/16/268864/268880
    M  DpShMCreate: sizeof(file_adm)        268880    (80)
    M  DpShMCreate: sizeof(vmc_adm)        30128    (2152)
    M  DpShMCreate: sizeof(wall_adm)        (41664/36752/64/192)
    M  DpShMCreate: sizeof(gw_adm)    48
    M  DpShMCreate: sizeof(j2ee_adm)    3936
    M  DpShMCreate: SHM_DP_ADM_KEY        (addr: 000000000DE60050, size: 6812336)
    M  DpShMCreate: allocated sys_adm at 000000000DE60060
    M  DpShMCreate: allocated wp_adm_list at 000000000DE63030
    M  DpShMCreate: allocated wp_adm at 000000000DE63220
    M  DpShMCreate: allocated tm_adm_list at 000000000DE6AE00
    M  DpShMCreate: allocated tm_adm at 000000000DE6AE50
    M  DpShMCreate: allocated wp_ca_adm at 000000000E3ADD60
    M  DpShMCreate: allocated appc_ca_adm at 000000000E3BD770
    M  DpShMCreate: allocated comm_adm at 000000000E3CD180
    M  DpShMCreate: allocated slock_adm at 000000000E45BB20
    M  DpShMCreate: allocated file_adm at 000000000E481CD0
    M  DpShMCreate: allocated vmc_adm_list at 000000000E4C3730
    M  DpShMCreate: allocated vmc_adm at 000000000E4C37E0
    M  DpShMCreate: allocated gw_adm at 000000000E4CADA0
    M  DpShMCreate: allocated j2ee_adm at 000000000E4CADE0
    M  DpShMCreate: allocated ca_info at 000000000E4CBD50
    M  DpShMCreate: allocated wall_adm at 000000000E4CBD70
    M  DpCommAttachTable: attached comm table (header=000000000E3CD180/ft=000000000E3CD190)
    M  DpSesCreateTable: attached session table at 0000000002C50050 (len=161328)
    M  DpRqQInit: use protect_queue / slots_per_queue 0 / 2001 from sys_adm
    M  rdisp/queue_size_check_value :  -> on,50,30,40,500,50,500,80
    X  EmInit: MmSetImplementation( 2 ).
    X  MM global diagnostic options set: 0
    X  <ES> client 0 initializing ....
    X  Using implementation view
    X  <EsNT> Using memory model view.
    M  <EsNT> Memory Reset disabled as NT default
    X  ES initialized.
    M  DpVmcSetActive: set vmc state DP_VMC_ENABLED
    M  DpVmcSetActive: set vmc state DP_VMC_ACTIVE
    M  DpVmcInit2: o.k.
    M  ThStart: taskhandler started
    M  ThInit: initializing DIA work process W0
    M 
    M Thu Aug 07 20:28:45 2014
    M  ThInit: running on host BIG
    M  calling db_connect ...
    B  create_con (con_name=R/3)
    B  Loading DB library 'C:\usr\sap\NSP\DVEBMGS00\exe\dbsdbslib.dll' ...
    B  Library 'C:\usr\sap\NSP\DVEBMGS00\exe\dbsdbslib.dll' loaded
    B  Version of 'C:\usr\sap\NSP\DVEBMGS00\exe\dbsdbslib.dll' is "720.00", patchlevel (0.45)
    B  New connection 0 created
    C 
    C  DBSDBSLIB : version 720.00, patch 0.045 (Make PL 0.46)
    C  MAXDB shared library (dbsdbslib) patchlevels (last 10)
    C    (0.045) Unknown primary key (note 1459400)
    C    (0.039) Define your own command buffersize (note 1340617)
    C    (0.031) Dbm commands support added (note 1420733)
    C    (0.027) Count of records for bulk insert optimized (note 1340617)
    C    (0.021) Connect with special xuser key (note 1390464)
    C    (0.018) Error handling for external update statistics changed (note 1340617)
    C    (0.018) Dbsl procedure to update datasource information (note 1340617)
    C    (0.015) Special describe handling on MaxDB systemtables (note 1382175)
    C    (0.013) Possibility to disable UPSERT statements (note 1340617)
    C    (0.013) Check for external update statistics changed (note 1340617)
    C 
    C 
    C  Loading SQLDBC client runtime ...
    C  SQLDBC Module  : C:\sapdb\clients\NSP\pgm\libSQLDBC77.dll
    C  SQLDBC SDK     : SQLDBC.H  7.7.4    BUILD 009-123-173-450
    C  SQLDBC Runtime : libSQLDBC 7.8.1    BUILD 014-121-233-288
    C  SQLDBC client runtime is MaxDB 7.8.1.014 CL 233288
    C  SQLDBC supports new DECIMAL interface : 1
    C  SQLDBC supports VARIABLE INPUT data   : 1
    C  SQLDBC supports VARIABLE OUTPUT data  : 1
    C  SQLDBC supports Multiple Streams      : 1
    C  SQLDBC supports LOB LOCATOR KEEPALIVE : 1
    C  SQLDBC supports LOB LOCATOR COPY      : 1
    C  SQLDBC supports BULK SELECT with LOBS : 1
    C  INFO : SQLOPT= -I 0 -t 0 -S SAPR3
    C  Try to connect (DEFAULT) on connection 0 ...
    C  Attach to SAP DB : Kernel    7.8.01   Build 014-121-233-288
    C  Database release is SAP DB 7.8.01.014
    C  INFO : Database 'NSP' instance is running on 'minisap'
    C 
    C Thu Aug 07 20:28:46 2014
    C  DB supports UPSERT SQL syntax : 1
    C  DB supports new EXPAND syntax : 1
    C  DB supports LOB locators      : 1
    C  DB uses MVCC support          : 0
    C  DB max. input host variables  : 2000
    C  INFO : SAP DB Packet_Size = 131072
    C  INFO : SAP DB Min_Reply_Size = 4096
    C  INFO : SAP DB Comm_Size = 126976
    C  INFO : DBSL buffer size = 126976
    C  INFO : SAP DB MaxLocks = 300000
    C  INFO : Connect to DB as 'SAPNSP'
    C  Command info enabled
    C  Now I'm connected to MaxDB
    C  00: minisap-NSP, since=20140807202845, ABAP= <unknown> (0)
    B  Connection 0 opened (DBSL handle 0)
    B  Wp  Hdl ConName          ConId     ConState     TX  BC  HC  PRM RCT FRC TIM MAX OPT Date     Time   DBHost           Program                                
    B  000 000 R/3              000000000 ACTIVE       NO  NO  NO  YES NO  NO  000 255 255 20140807 202845 minisap                                                 
    C  INFO : SAP RELEASE (DB) = 702
    M  ThInit: db_connect o.k.
    M  ICT: exclude compression: *.zip,*.rar,*.arj,*.z,*.gz,*.tar,*.lzh,*.cab,*.hqx,*.ace,*.jar,*.ear,*.war,*.css,*.pdf,*.gzip,*.uue,*.bz2,*.iso,*.sda,*.sar,*.gif,*.png,*.swc,*.swf
    M  vmcj/sgc_options: switch on template cleanup before cloning
    M  vmcj/sgc_options: switch off delayed session cleanup during shared gc
    M  ThVmcInitWaitForVm: th_maxWaitForVmTime=30
    M  ThVmcInitMaxErrCount: th_max_error_count=5
    I  MtxInit: 0 0 0
    M  SHM_PRES_BUF            (addr: 0000000014780050, size: 4400000)
    M  SHM_ROLL_AREA        (addr: 000007FEC3B40050, size: 268435456)
    M  SHM_PAGING_AREA        (addr: 0000000014BC0050, size: 134217728)
    M  SHM_ROLL_ADM            (addr: 000000001CBD0050, size: 2767448)
    M  SHM_PAGING_ADM        (addr: 00000000124B0050, size: 525344)
    M  ThCreateNoBuffer        allocated 548152 bytes for 1000 entries at 0000000012540050
    M  ThCreateNoBuffer        index size: 3000 elems
    M  ThCreateVBAdm        allocated 30976 bytes (50 server) at 0000000002EF0050
    X  EmInit: MmSetImplementation( 2 ).
    X  MM global diagnostic options set: 0
    X  <ES> client 0 initializing ....
    X  Using implementation view
    X  ES initialized.
    B  db_con_shm_ini:  WP_ID = 0, WP_CNT = 14, CON_ID = -1
    B  dbtbxbuf: Buffer TABL  (addr: 00000000208B0160, size: 30000000, end: 000000002254C4E0)
    B  dbtbxbuf: Buffer TABLP (addr: 0000000022550160, size: 10240000, end: 0000000022F14160)
    B  dbexpbuf: Buffer EIBUF (addr: 0000000022F20170, size: 4194304, end: 0000000023320170)
    B  dbexpbuf: Buffer ESM   (addr: 0000000023330170, size: 4194304, end: 0000000023730170)
    B  dbexpbuf: Buffer CUA   (addr: 0000000023740170, size: 3072000, end: 0000000023A2E170)
    B  dbexpbuf: Buffer OTR   (addr: 0000000023A30170, size: 4194304, end: 0000000023E30170)
    I  MPI: dynamic quotas disabled.
    I  MPI init: pipes=4000 buffers=1279 reserved=383 quota=10%
    M  CCMS uses Shared Memory Key 73 for monitoring.
    M  CCMS: SemInMgt: Semaphore Management initialized by AlAttachShm_Doublestack.
    M  CCMS: SemInit: Semaphore 38 initialized by AlAttachShm_Doublestack.
    M  CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
    S  *** init spool environment
    S  TSPEVJOB updates outside critical section: event_update_nocsec = 1
    S  initialize debug system
    T  Stack direction is downwards.
    T  debug control: prepare exclude for printer trace
    T  new memory block 000000001334FCE0
    S  spool kernel/ddic check: Ok
    S  using table TSP02FX for frontend printing
    S  1 spool work process(es) found
    S  frontend print via spool service enabled
    S  printer list size is 150
    S  printer type list size is 50
    S  queue size (profile)   = 300
    S  hostspool list size = 3000
    S  option list size is 30
    S      found processing queue enabled
    S  found spool memory service RSPO-RCLOCKS at 000000002D1B00D0
    S  doing lock recovery
    S  setting server cache root
    S  found spool memory service RSPO-SERVERCACHE at 000000002D1B0530
    S    using messages for server info
    S  size of spec char cache entry: 297032 bytes (timeout 100 sec)
    S  size of open spool request entry: 2512 bytes
    S  immediate print option for implicitely closed spool requests is disabled
    A  ***GENER* Trace switched on ***
    A 
    A  ---PXA-------------------------------------------
    A  PXA INITIALIZATION
    A  System page size: 4kb, total admin_size: 22076kb, dir_size: 21360kb.
    A  Attached to PXA (address 000007FED3B70050, size 300000K, 1 fragments of 277924K )
    A  PXA allocated (address 000007FED3B70050, size 300000K)
    A  *** WARNING: INTERNAL_KERNEL_VERSION of message server
    A               unknown yet.
    A  abap/pxa = shared protect gen_remote
    A  PXA: checking structure sizes: 752|264|16
    A  PXA INITIALIZATION FINISHED
    A  ---PXA-------------------------------------------
    A 
    A  ABAP ShmAdm attached (addr=000007FFDF0EE000 leng=20955136 end=000007FFE04EA000)
    A  >> Shm MMADM area (addr=000007FFDF5E2970 leng=242368 end=000007FFDF61DC30)
    A  >> Shm MMDAT area (addr=000007FFDF61E000 leng=15511552 end=000007FFE04E9000)
    A  RFC Destination> destination BIG_NSP_00 host BIG system NSP systnr 0 (BIG_NSP_00)
    A  RFC Options> H=BIG,S=00,d=2,
    A  RFC FRFC> fallback activ but this is not a central instance.
    A   
    A  RFC rfc/signon_error_log = -1
    A  RFC rfc/dump_connection_info = 0
    A  RFC rfc/dump_client_info = 0
    A  RFC rfc/cp_convert/ignore_error = 1
    A  RFC rfc/cp_convert/conversion_char = 23
    A  RFC rfc/wan_compress/threshold = 251
    A  RFC rfc/recorder_pcs not set, use defaule value: 2
    A  RFC rfc/delta_trc_level not set, use default value: 0
    A  RFC rfc/no_uuid_check not set, use default value: 0
    B  dbtran INFO (init_connection '<DEFAULT>' [ADABAS D:720.00]):
    B   max_blocking_factor =  10,  max_in_blocking_factor      = 127,
    B   min_blocking_factor =  10,  min_in_blocking_factor      = 127,
    B   prefer_union_all    =   1,  prefer_join                 =   0,
    B   prefer_fix_blocking =   0,  prefer_in_itab_opt          =   1,
    B   convert AVG         =   0,  alias table FUPD            =   0,
    B   escape_as_literal   =   0,                                  
    B   select *            =0x0f,  character encoding          = STD / <none>:-,
    B   use_hints           = abap->1, dbif->0x1, upto->4294967295
    M  ThrCreateShObjects        allocated 29124 bytes at 0000000002F20050
    N  SsfSapSecin: putenv(SECUDIR=C:\usr\sap\NSP\DVEBMGS00\sec): ok
    N 
    N  =================================================
    N  === SSF INITIALIZATION:
    N  ===...SSF Security Toolkit name SAPSECULIB .
    N  ===...SSF library is C:\usr\sap\NSP\DVEBMGS00\exe\sapsecu.dll .
    N  ===...SSF default hash algorithm is SHA1 .
    N  ===...SSF default symmetric encryption algorithm is DES-CBC .
    N  ===...SECUDIR="C:\usr\sap\NSP\DVEBMGS00\sec"
    N  ===...loading of Security Toolkit successfully completed.
    N  ===   SAPSECULIB Version 5.4.28M-6
    N  =================================================
    N  MskiInitLogonTicketCacheHandle: Logon Ticket cache pointer retrieved from shared memory.
    N  MskiInitLogonTicketCacheHandle: Workprocess runs with Logon Ticket cache.
    M  JrfcVmcRegister in process-driver OK
    M  JrfcVmcRegisterNativesDriver o.k.
    W  =================================================
    W  === ipl_Init() called
    W    ITS Plugin: Path dw_gui
    W    ITS Plugin: Description ITS Plugin - ITS rendering DLL
    W    ITS Plugin: sizeof(SAP_UC) 2
    W    ITS Plugin: Release: 720, [7200.0.46.20020600]
    W    ITS Plugin: Int.version, [33]
    W    ITS Plugin: Feature set: [23]
    W    ===... Calling itsp_Init in external dll ===>
    W      PpioRecoverLocks, table: 000007FFE04EDB30
    W      PpioRecoverLocks, number of file locks 256
    W      PpioRecoverLocks: file lock set to: 0000000000000000
    W      PpioRecoverLocks: directory lock set to: 0000000000000000
    W      PpioRecoverLocks: global lock set to: 0000000000000000
    W      PpioRecoverLocks() done
    W      PprcRecoverLocks, table: 000007FFE04EE020
    W      PprcRecoverLocks: directory lock set to: 0000000000000000
    W      PprcRecoverLocks() done
    W  === ipl_Init() returns 0, ITSPE_OK: OK
    W  =================================================
    N  SignInit: successfully obtained handle for Security Context cache
    N  VSI: WP init in ABAP VM completed with rc=0
    E  Enqueue Info: rdisp/wp_no_enq=1, rdisp/enqname=<empty>, assume BIG_NSP_00
    E  Enqueue Info: enque/use_pfclock2 = FALSE
    E  Enqueue Info: row condense enabled
    E  Enqueue Info: enque/use_pfclock2 = FALSE
    E  Replication is disabled
    E  EnqCcInitialize: local lock table initialization o.k.
    E  EnqId_SuppressIpc: local EnqId initialization o.k.
    E  EnqCcInitialize: local enqueue client init o.k.
    M 
    M Thu Aug 07 20:28:47 2014
    M  ***LOG Q0I=> NiPConnect2: 127.0.0.1:65000: connect (10061: WSAECONNREFUSED: Connection refused) [nixxi.cpp 3271]
    M  *** ERROR => NiPConnect2: SiPeekPendConn failed for hdl 1/sock 1340
        (SI_ECONN_REFUSE/10061; I4; ST; 127.0.0.1:65000) [nixxi.cpp    3271]
    M  *** ERROR => IcmConnect: NiConnect to localhost:65000,-1 (rc=-10) [icxxext.c    182]
    M  *** ERROR => ThPlgConnectToIcm: IcmConnect failed (-10) [thxxplg.c    5120]
    M  in_ThErrHandle: 1
    M  *** ERROR => ThStart: connect to icman (step 1, th_errno 2, action 3, level 1) [thxxhead.c   11087]
    M 
    M  Info for wp 0
    M 
    M    pid = 7620
    M    severity = 0
    M    status = 0
    M    stat = WP_NEW
    M    waiting_for = NO_WAITING
    M    reqtype = DP_RQ_DIAWP
    M    act_reqtype = NO_REQTYPE
    M    req.req_info =
    M    req.tid = -1
    M    req.uid = 4294967295
    M    req.mode = 255
    M    req.len = -1
    M    req.rq_id = 65535
    M    req.rq_source =
    M    req.vm = no VM
    M    last_tid = 0
    M    last_uid = 0
    M    last_mode = 0
    M    act_cs_count = 0
    M    csTrack = 0
    M    csTrackRwExcl = 0
    M    csTrackRwShrd = 0
    M    mode_cleaned_counter = 0
    M    control_flag = 0
    M    int_checked_resource(RFC) = 0
    M    ext_checked_resource(RFC) = 0
    M    int_checked_resource(HTTP) = 0
    M    ext_checked_resource(HTTP) = 0
    M    report = >                                        <
    M    action = 0
    M    tab_name = >                              <
    M    attachedVm = no VM
    M 
    M  ThIErrHandle: current request:
    M 
    M  -IN-- sender_id ?                 tid  -1    wp_ca_blk   -1      wp_id -1
    M  -IN-- action    -                 uid  -1    appc_ca_blk -1      type  -   
    M  -IN-- new_stat  NO_CHANGE         mode 255   len         -1      rq_id -1
    M  PfStatDisconnect: disconnect statistics
    M  Entering TH_CALLHOOKS
    M  ThCallHooks: call hook >TrThHookFunc< for event BEFORE_DUMP
    M  TrThHookFunc: called for WP dump
    M  ThCallHooks: hook >TrThHookFunc< o.k.
    M  ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
    M  ThrSaveSPAFields: save spa fields
    M  ThrSaveSPAFields: not an update task, no update info saved
    M  ThrSaveSPAFields: not a batch task, field zttabtckey not saved
    M  ThCallHooks: hook >ThrSaveSPAFields< o.k.
    M  ThCallHooks: call hook >ThrBtcCallLgCl< for event BEFORE_DUMP
    M  ThCallHooks: hook >ThrBtcCallLgCl< o.k.
    M  ThIErrHandle: entering ThSetStatError
    M  ThIErrHandle: do not call ThrCoreInfo (no_core_info=0, in_dynp_env=0)
    M  Entering ThReadDetachMode
    M  call ThrShutDown (1)...
    M  ***LOG Q02=> wp_halt, WPStop (Workp. 0 7620) [dpnttool.c   339]
    trc file: "dev_w0", trc level: 1, release: "720"
    *  ACTIVE TRACE LEVEL           1
    *  ACTIVE TRACE COMPONENTS      all, MJ
    M sysno      00
    M sid        NSP
    M systemid   562 (PC with Windows NT)
    M relno      7200
    M patchlevel 0
    M patchno    46
    M intno      20020600
    M make       multithreaded, Unicode, 64 bit, optimized
    M profile    \\BIG\sapmnt\NSP\SYS\profile\NSP_DVEBMGS00_BIG
    M pid        7828
    M
    M 
    M Thu Aug 07 20:33:43 2014
    M  kernel runs with dp version 125000(ext=118000) (@(#) DPLIB-INT-VERSION-125000-UC)
    M  length of sys_adm_ext is 588 bytes
    M  ***LOG Q0Q=> tskh_init, WPStart (Workp. 0 7828) [dpxxdisp.c   1314]
    I  MtxInit: 30000 0 0
    M  DpSysAdmExtCreate: ABAP is active
    M  DpSysAdmExtCreate: VMC (JAVA VM in WP) is active
    M  DpIPCInit2: read dp-profile-values from sys_adm_ext
    M  DpShMCreate: sizeof(wp_adm)        31696    (2264)
    M  DpShMCreate: sizeof(tm_adm)        5517056    (27448)
    M  DpShMCreate: sizeof(wp_ca_adm)        64000    (64)
    M  DpShMCreate: sizeof(appc_ca_adm)    64000    (64)
    M  DpCommTableSize: max/headSize/ftSize/tableSize=500/16/584064/584080
    M  DpShMCreate: sizeof(comm_adm)        584080    (1144)
    M  DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=512/48/65600/90416/156064
    M  DpShMCreate: sizeof(slock_adm)        156064    (104)
    M  DpFileTableSize: max/headSize/ftSize/tableSize=2800/16/268864/268880
    M  DpShMCreate: sizeof(file_adm)        268880    (80)
    M  DpShMCreate: sizeof(vmc_adm)        30128    (2152)
    M  DpShMCreate: sizeof(wall_adm)        (41664/36752/64/192)
    M  DpShMCreate: sizeof(gw_adm)    48
    M  DpShMCreate: sizeof(j2ee_adm)    3936
    M  DpShMCreate: SHM_DP_ADM_KEY        (addr: 000000000DD90050, size: 6812336)
    M  DpShMCreate: allocated sys_adm at 000000000DD90060
    M  DpShMCreate: allocated wp_adm_list at 000000000DD93030
    M  DpShMCreate: allocated wp_adm at 000000000DD93220
    M  DpShMCreate: allocated tm_adm_list at 000000000DD9AE00
    M  DpShMCreate: allocated tm_adm at 000000000DD9AE50
    M  DpShMCreate: allocated wp_ca_adm at 000000000E2DDD60
    M  DpShMCreate: allocated appc_ca_adm at 000000000E2ED770
    M  DpShMCreate: allocated comm_adm at 000000000E2FD180
    M  DpShMCreate: allocated slock_adm at 000000000E38BB20
    M  DpShMCreate: allocated file_adm at 000000000E3B1CD0
    M  DpShMCreate: allocated vmc_adm_list at 000000000E3F3730
    M  DpShMCreate: allocated vmc_adm at 000000000E3F37E0
    M  DpShMCreate: allocated gw_adm at 000000000E3FADA0
    M  DpShMCreate: allocated j2ee_adm at 000000000E3FADE0
    M  DpShMCreate: allocated ca_info at 000000000E3FBD50
    M  DpShMCreate: allocated wall_adm at 000000000E3FBD70
    M  DpCommAttachTable: attached comm table (header=000000000E2FD180/ft=000000000E2FD190)
    M  DpSesCreateTable: attached session table at 0000000002990050 (len=161328)
    M  DpRqQInit: use protect_queue / slots_per_queue 0 / 2001 from sys_adm
    M  rdisp/queue_size_check_value :  -> on,50,30,40,500,50,500,80
    X  EmInit: MmSetImplementation( 2 ).
    X  MM global diagnostic options set: 0
    X  <ES> client 0 initializing ....
    X  Using implementation view
    X  <EsNT> Using memory model view.
    M  <EsNT> Memory Reset disabled as NT default
    X  ES initialized.
    M  DpVmcSetActive: set vmc state DP_VMC_ENABLED
    M  DpVmcSetActive: set vmc state DP_VMC_ACTIVE
    M  DpVmcInit2: o.k.
    M  ThStart: taskhandler started
    M  ThInit: initializing DIA work process W0
    M 
    M Thu Aug 07 20:33:44 2014
    M  ThInit: running on host BIG
    M 
    M Thu Aug 07 20:33:45 2014
    M  calling db_connect ...
    B  create_con (con_name=R/3)
    B  Loading DB library 'C:\usr\sap\NSP\DVEBMGS00\exe\dbsdbslib.dll' ...
    B  Library 'C:\usr\sap\NSP\DVEBMGS00\exe\dbsdbslib.dll' loaded
    B  Version of 'C:\usr\sap\NSP\DVEBMGS00\exe\dbsdbslib.dll' is "720.00", patchlevel (0.45)
    B  New connection 0 created
    C 
    C  DBSDBSLIB : version 720.00, patch 0.045 (Make PL 0.46)
    C  MAXDB shared library (dbsdbslib) patchlevels (last 10)
    C    (0.045) Unknown primary key (note 1459400)
    C    (0.039) Define your own command buffersize (note 1340617)
    C    (0.031) Dbm commands support added (note 1420733)
    C    (0.027) Count of records for bulk insert optimized (note 1340617)
    C    (0.021) Connect with special xuser key (note 1390464)
    C    (0.018) Error handling for external update statistics changed (note 1340617)
    C    (0.018) Dbsl procedure to update datasource information (note 1340617)
    C    (0.015) Special describe handling on MaxDB systemtables (note 1382175)
    C    (0.013) Possibility to disable UPSERT statements (note 1340617)
    C    (0.013) Check for external update statistics changed (note 1340617)
    C 
    C 
    C  Loading SQLDBC client runtime ...
    C  SQLDBC Module  : C:\sapdb\clients\NSP\pgm\libSQLDBC77.dll
    C  SQLDBC SDK     : SQLDBC.H  7.7.4    BUILD 009-123-173-450
    C  SQLDBC Runtime : libSQLDBC 7.8.1    BUILD 014-121-233-288
    C  SQLDBC client runtime is MaxDB 7.8.1.014 CL 233288
    C  SQLDBC supports new DECIMAL interface : 1
    C  SQLDBC supports VARIABLE INPUT data   : 1
    C  SQLDBC supports VARIABLE OUTPUT data  : 1
    C  SQLDBC supports Multiple Streams      : 1
    C  SQLDBC supports LOB LOCATOR KEEPALIVE : 1
    C  SQLDBC supports LOB LOCATOR COPY      : 1
    C  SQLDBC supports BULK SELECT with LOBS : 1
    C  INFO : SQLOPT= -I 0 -t 0 -S SAPR3
    C  Try to connect (DEFAULT) on connection 0 ...
    C  Attach to SAP DB : Kernel    7.8.01   Build 014-121-233-288
    C  Database release is SAP DB 7.8.01.014
    C  INFO : Database 'NSP' instance is running on 'minisap'
    C  DB supports UPSERT SQL syntax : 1
    C  DB supports new EXPAND syntax : 1
    C  DB supports LOB locators      : 1
    C  DB uses MVCC support          : 0
    C  DB max. input host variables  : 2000
    C  INFO : SAP DB Packet_Size = 131072
    C  INFO : SAP DB Min_Reply_Size = 4096
    C  INFO : SAP DB Comm_Size = 126976
    C  INFO : DBSL buffer size = 126976
    C  INFO : SAP DB MaxLocks = 300000
    C  INFO : Connect to DB as 'SAPNSP'
    C  Command info enabled
    C  Now I'm connected to MaxDB
    C  00: minisap-NSP, since=20140807203345, ABAP= <unknown> (0)
    B  Connection 0 opened (DBSL handle 0)
    B  Wp  Hdl ConName          ConId     ConState     TX  BC  HC  PRM RCT FRC TIM MAX OPT Date     Time   DBHost           Program                                
    B  000 000 R/3              000000000 ACTIVE       NO  NO  NO  YES NO  NO  000 255 255 20140807 203345 minisap                                                 
    C  INFO : SAP RELEASE (DB) = 702
    M  ThInit: db_connect o.k.
    M  ICT: exclude compression: *.zip,*.rar,*.arj,*.z,*.gz,*.tar,*.lzh,*.cab,*.hqx,*.ace,*.jar,*.ear,*.war,*.css,*.pdf,*.gzip,*.uue,*.bz2,*.iso,*.sda,*.sar,*.gif,*.png,*.swc,*.swf
    M  vmcj/sgc_options: switch on template cleanup before cloning
    M  vmcj/sgc_options: switch off delayed session cleanup during shared gc
    M  ThVmcInitWaitForVm: th_maxWaitForVmTime=30
    M  ThVmcInitMaxErrCount: th_max_error_count=5
    I  MtxInit: 0 0 0
    M  SHM_PRES_BUF            (addr: 0000000014760050, size: 4400000)
    M  SHM_ROLL_AREA        (addr: 000007FEC3B40050, size: 268435456)
    M  SHM_PAGING_AREA        (addr: 0000000014BA0050, size: 134217728)
    M  SHM_ROLL_ADM            (addr: 000000001CBB0050, size: 2767448)
    M  SHM_PAGING_ADM        (addr: 0000000005930050, size: 525344)
    M  ThCreateNoBuffer        allocated 548152 bytes for 1000 entries at 0000000005A60050
    M  ThCreateNoBuffer        index size: 3000 elems
    M  ThCreateVBAdm        allocated 30976 bytes (50 server) at 0000000002BC0050
    X  EmInit: MmSetImplementation( 2 ).
    X  MM global diagnostic options set: 0
    X  <ES> client 0 initializing ....
    X  Using implementation view
    X  ES initialized.
    B  db_con_shm_ini:  WP_ID = 0, WP_CNT = 14, CON_ID = -1
    B  dbtbxbuf: Buffer TABL  (addr: 0000000020890160, size: 30000000, end: 000000002252C4E0)
    B  dbtbxbuf: Buffer TABLP (addr: 0000000022530160, size: 10240000, end: 0000000022EF4160)
    B  dbexpbuf: Buffer EIBUF (addr: 0000000022F00170, size: 4194304, end: 0000000023300170)
    B  dbexpbuf: Buffer ESM   (addr: 0000000023310170, size: 4194304, end: 0000000023710170)
    B  dbexpbuf: Buffer CUA   (addr: 0000000023720170, size: 3072000, end: 0000000023A0E170)
    B  dbexpbuf: Buffer OTR   (addr: 0000000023A10170, size: 4194304, end: 0000000023E10170)
    I  MPI: dynamic quotas disabled.
    I  MPI init: pipes=4000 buffers=1279 reserved=383 quota=10%
    M  CCMS uses Shared Memory Key 73 for monitoring.
    M 
    M Thu Aug 07 20:33:46 2014
    M  CCMS: SemInMgt: Semaphore Management initialized by AlAttachShm_Doublestack.
    M  CCMS: SemInit: Semaphore 38 initialized by AlAttachShm_Doublestack.
    M  CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
    S  *** init spool environment
    S  TSPEVJOB updates outside critical section: event_update_nocsec = 1
    S  initialize debug system
    T  Stack direction is downwards.
    T  debug control: prepare exclude for printer trace
    T  new memory block 000000001322FCE0
    S  spool kernel/ddic check: Ok
    S  using table TSP02FX for frontend printing
    S  1 spool work process(es) found
    S  frontend print via spool service enabled
    S  printer list size is 150
    S  printer type list size is 50
    S  queue size (profile)   = 300
    S  hostspool list size = 3000
    S  option list size is 30
    S      found processing queue enabled
    S  found spool memory service RSPO-RCLOCKS at 000000002D1900D0
    S  doing lock recovery
    S  setting server cache root
    S  found spool memory service RSPO-SERVERCACHE at 000000002D190530
    S    using messages for server info
    S  size of spec char cache entry: 297032 bytes (timeout 100 sec)
    S  size of open spool request entry: 2512 bytes
    S  immediate print option for implicitely closed spool requests is disabled
    A  ***GENER* Trace switched on ***
    A 
    A  ---PXA-------------------------------------------
    A  PXA INITIALIZATION
    A  System page size: 4kb, total admin_size: 22076kb, dir_size: 21360kb.
    A  Attached to PXA (address 000007FED3B70050, size 300000K, 1 fragments of 277924K )
    A  PXA allocated (address 000007FED3B70050, size 300000K)
    A  *** WARNING: INTERNAL_KERNEL_VERSION of message server
    A               unknown yet.
    A  abap/pxa = shared protect gen_remote
    A  PXA: checking structure sizes: 752|264|16
    A  PXA INITIALIZATION FINISHED
    A  ---PXA-------------------------------------------
    A 
    A  ABAP ShmAdm attached (addr=000007FFDF0EE000 leng=20955136 end=000007FFE04EA000)
    A  >> Shm MMADM area (addr=000007FFDF5E2970 leng=242368 end=000007FFDF61DC30)
    A  >> Shm MMDAT area (addr=000007FFDF61E000 leng=15511552 end=000007FFE04E9000)
    A  RFC Destination> destination BIG_NSP_00 host BIG system NSP systnr 0 (BIG_NSP_00)
    A  RFC Options> H=BIG,S=00,d=2,
    A  RFC FRFC> fallback activ but this is not a central instance.
    A   
    A  RFC rfc/signon_error_log = -1
    A  RFC rfc/dump_connection_info = 0
    A  RFC rfc/dump_client_info = 0
    A  RFC rfc/cp_convert/ignore_error = 1
    A  RFC rfc/cp_convert/conversion_char = 23
    A  RFC rfc/wan_compress/threshold = 251
    A  RFC rfc/recorder_pcs not set, use defaule value: 2
    A  RFC rfc/delta_trc_level not set, use default value: 0
    A  RFC rfc/no_uuid_check not set, use default value: 0
    B  dbtran INFO (init_connection '<DEFAULT>' [ADABAS D:720.00]):
    B   max_blocking_factor =  10,  max_in_blocking_factor      = 127,
    B   min_blocking_factor =  10,  min_in_blocking_factor      = 127,
    B   prefer_union_all    =   1,  prefer_join                 =   0,
    B   prefer_fix_blocking =   0,  prefer_in_itab_opt          =   1,
    B   convert AVG         =   0,  alias table FUPD            =   0,
    B   escape_as_literal   =   0,                                  
    B   select *            =0x0f,  character encoding          = STD / <none>:-,
    B   use_hints           = abap->1, dbif->0x1, upto->4294967295
    M  ThrCreateShObjects        allocated 29124 bytes at 0000000002BE0050
    N  SsfSapSecin: putenv(SECUDIR=C:\usr\sap\NSP\DVEBMGS00\sec): ok
    N 
    N  =================================================
    N  === SSF INITIALIZATION:
    N  ===...SSF Security Toolkit name SAPSECULIB .
    N  ===...SSF library is C:\usr\sap\NSP\DVEBMGS00\exe\sapsecu.dll .
    N  ===...SSF default hash algorithm is SHA1 .
    N  ===...SSF default symmetric encryption algorithm is DES-CBC .
    N  ===...SECUDIR="C:\usr\sap\NSP\DVEBMGS00\sec"
    N  ===...loading of Security Toolkit successfully completed.
    N  ===   SAPSECULIB Version 5.4.28M-6
    N  =================================================
    N  MskiInitLogonTicketCacheHandle: Logon Ticket cache pointer retrieved from shared memory.
    N  MskiInitLogonTicketCacheHandle: Workprocess runs with Logon Ticket cache.
    M  JrfcVmcRegister in process-driver OK
    M  JrfcVmcRegisterNativesDriver o.k.
    W  =================================================
    W  === ipl_Init() called
    W    ITS Plugin: Path dw_gui
    W    ITS Plugin: Description ITS Plugin - ITS rendering DLL
    W    ITS Plugin: sizeof(SAP_UC) 2
    W    ITS Plugin: Release: 720, [7200.0.46.20020600]
    W    ITS Plugin: Int.version, [33]
    W    ITS Plugin: Feature set: [23]
    W    ===... Calling itsp_Init in external dll ===>
    W      PpioRecoverLocks, table: 000007FFE04EDB30
    W      PpioRecoverLocks, number of file locks 256
    W      PpioRecoverLocks: file lock set to: 0000000000000000
    W      PpioRecoverLocks: directory lock set to: 0000000000000000
    W      PpioRecoverLocks: global lock set to: 0000000000000000
    W      PpioRecoverLocks() done
    W      PprcRecoverLocks, table: 000007FFE04EE020
    W      PprcRecoverLocks: directory lock set to: 0000000000000000
    W      PprcRecoverLocks() done
    W  === ipl_Init() returns 0, ITSPE_OK: OK
    W  =================================================
    N  SignInit: successfully obtained handle for Security Context cache
    N  VSI: WP init in ABAP VM completed with rc=0
    E  Enqueue Info: rdisp/wp_no_enq=1, rdisp/enqname=<empty>, assume BIG_NSP_00
    E  Enqueue Info: enque/use_pfclock2 = FALSE
    E  Enqueue Info: row condense enabled
    E  Enqueue Info: enque/use_pfclock2 = FALSE
    E  Replication is disabled
    E  EnqCcInitialize: local lock table initialization o.k.
    E  EnqId_SuppressIpc: local EnqId initialization o.k.
    E  EnqCcInitialize: local enqueue client init o.k.
    M 
    M Thu Aug 07 20:33:47 2014
    M  ***LOG Q0I=> NiPConnect2: 127.0.0.1:65000: connect (10061: WSAECONNREFUSED: Connection refused) [nixxi.cpp 3271]
    M  *** ERROR => NiPConnect2: SiPeekPendConn failed for hdl 1/sock 1340
        (SI_ECONN_REFUSE/10061; I4; ST; 127.0.0.1:65000) [nixxi.cpp    3271]
    M  *** ERROR => IcmConnect: NiConnect to localhost:65000,-1 (rc=-10) [icxxext.c    182]
    M  *** ERROR => ThPlgConnectToIcm: IcmConnect failed (-10) [thxxplg.c    5120]
    M  in_ThErrHandle: 1
    M  *** ERROR => ThStart: connect to icman (step 1, th_errno 2, action 3, level 1) [thxxhead.c   11087]
    M 
    M  Info for wp 0
    M 
    M    pid = 7828
    M    severity = 0
    M    status = 0
    M    stat = WP_NEW
    M    waiting_for = NO_WAITING
    M    reqtype = DP_RQ_DIAWP
    M    act_reqtype = NO_REQTYPE
    M    req.req_info =
    M    req.tid = -1
    M    req.uid = 4294967295
    M    req.mode = 255
    M    req.len = -1
    M    req.rq_id = 65535
    M    req.rq_source =
    M    req.vm = no VM
    M    last_tid = 0
    M    last_uid = 0
    M    last_mode = 0
    M    act_cs_count = 0
    M    csTrack = 0
    M    csTrackRwExcl = 0
    M    csTrackRwShrd = 0
    M    mode_cleaned_counter = 0
    M    control_flag = 0
    M    int_checked_resource(RFC) = 0
    M    ext_checked_resource(RFC) = 0
    M    int_checked_resource(HTTP) = 0
    M    ext_checked_resource(HTTP) = 0
    M    report = >                                        <
    M    action = 0
    M    tab_name = >                              <
    M    attachedVm = no VM
    M 
    M  ThIErrHandle: current request:
    M 
    M  -IN-- sender_id ?                 tid  -1    wp_ca_blk   -1      wp_id -1
    M  -IN-- action    -                 uid  -1    appc_ca_blk -1      type  -   
    M  -IN-- new_stat  NO_CHANGE         mode 255   len         -1      rq_id -1
    M  PfStatDisconnect: disconnect statistics
    M  Entering TH_CALLHOOKS
    M  ThCallHooks: call hook >TrThHookFunc< for event BEFORE_DUMP
    M  TrThHookFunc: called for WP dump
    M  ThCallHooks: hook >TrThHookFunc< o.k.
    M  ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
    M  ThrSaveSPAFields: save spa fields
    M  ThrSaveSPAFields: not an update task, no update info saved
    M  ThrSaveSPAFields: not a batch task, field zttabtckey not saved
    M  ThCallHooks: hook >ThrSaveSPAFields< o.k.
    M  ThCallHooks: call hook >ThrBtcCallLgCl< for event BEFORE_DUMP
    M  ThCallHooks: hook >ThrBtcCallLgCl< o.k.
    M  ThIErrHandle: entering ThSetStatError
    M  ThIErrHandle: do not call ThrCoreInfo (no_core_info=0, in_dynp_env=0)
    M  Entering ThReadDetachMode
    M  call ThrShutDown (1)...
    M  ***LOG Q02=> wp_halt, WPStop (Workp. 0 7828) [dpnttool.c   339]
    // END OF FILE
    i hope that we can bring my sap to runing?
    best regards
    mirso

Maybe you are looking for

  • A better way to auto set category to bank transactions

    I have a table with bank transactions, the third cell have "Memo", some kind of description, I want to classify the transaction based on words found in the "Memo" based in another table with first column with classification and the second column with

  • HP LaserJet Pro 200 color MFP M276nw Wireless option is gone!!!

    I have a HP LaserJet Pro 200 color MFP M276nw.  The blue lit wireless icon used to stay on steady and all was fine for quite a while, then the Blue icon would start flashing like it lost it connection to the wireless router.  I would just recycle the

  • Docking station problem

    sinse updating my iphone 4 to ios 6.1.2 my kitsound boomdock will not support it or my ipod 4th gen ??

  • Problem using Function Module IDOC_INBOUND_ASYNCHRONOUS

    Hi friends, I have a critical problem load idoc ARTMAS05. I development a program for load the data with idoc but my program call the function module IDOC_INBOUND_ASYNCHRONOUS close my session of the SAP GUI and lose the load. This problem begining t

  • Coldfusion bug?

    I have the folllowing code: <cfparam name="PageNum_EducationForumRS" default="1"> <cfquery name="CountOfResponses" datasource="Education Forum"> SELECT ParentID, Count(ParentID) as CountOfResponses FROM Messages GROUP BY PARENTID WHERE ParentID="#Ses