Cluster and deploying in AS 10.1.3

Hi,
I have a cluster of AS 10.1.3 of 3 elements in the way HTTP-OC4J at each one.
I deployed some ws at the 1st AS in the instance x and so in the cluster topology I see these on the 1st but not in the other AS - instance x
If I go to the http balanced page http://balanced:7777/nnn
should this go to any of the AS ?
Thanks

Hi Mohamed,
Now I understand that you're using 10.1.3.0 and not any one of the newer versions 10.1.3.1 or 10.1.3.2. In 10.1.3.0 you must create a new OC4J on command line. I don't have the syntax for command, but you'll find it in the Administration Guide.
However, I would strongly recommend installing 10.1.3.2 (or 10.1.3.1 if using SOA) instead of doing any more configuration on your old 10.1.3.0. The installation only takes an hour.
Regards,
Martin

Similar Messages

  • When setting up converged network in VMM cluster and live migration virtual nics not working

    Hello Everyone,
    I am having issues setting up converged network in VMM.  I have been working with MS engineers to no avail.  I am very surprised with the expertise of the MS engineers.  They had no idea what a converged network even was.  I had way more
    experience then these guys and they said there was no escalation track so I am posting here in hopes of getting some assistance.
    Everyone including our consultants says my setup is correct. 
    What I want to do:
    I have servers with 5 nics and want to use 3 of the nics for a team and then configure cluster, live migration and host management as virtual network adapters.  I have created all my logical networks, port profile with the uplink defined as team and
    networks selected.  Created logical switch and associated portprofle.  When I deploy logical switch and create virtual network adapters the logical switch works for VMs and my management nic works as well.  Problem is that the cluster and live
    migration virtual nics do not work.  The correct Vlans get pulled in for the corresponding networks and If I run get-vmnetworkadaptervlan it shows cluster and live migration in vlans 14 and 15 which is correct.  However nics do not work at all.
    I finally decided to do this via the host in powershell and everything works fine which means this is definitely an issue with VMM.  I then imported host into VMM again but now I cannot use any of the objects I created and VMM and have to use standard
    switch.
    I am really losing faith in VMM fast. 
    Hosts are 2012 R2 and VMM is 2012 R2 all fresh builds with latest drivers
    Thanks

    Have you checked our whitepaper http://gallery.technet.microsoft.com/Hybrid-Cloud-with-NVGRE-aa6e1e9a for how to configure this through VMM?
    Are you using static IP address assignment for those vNICs?
    Are you sure your are teaming the correct physical adapters where the VLANs are trunked through the connected ports?
    Note; if you create the teaming configuration outside of VMM, and then import the hosts to VMM, then VMM will not recognize the configuration. 
    The details should be all in this whitepaper.
    -kn
    Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )

  • Build using 32-bit Sun JDK in dev windows OS and deploy in 32-bit RHEL

    Is there any potential problems associated with building/compiling my Java classes for my EE (Seam) app into an EAR and deploying on 32-bit Windows OS JBoss AS dev box using 32-bit Windows JDK 1.5 and then deploying the same EAR into 32-bit RHEL OS JBoss AS? The dev envmt is not clustered and the UAT RHEL envmt is a 2 node horizontal cluster without state replication (only mod_jk load balancing and failover).
    Perhaps the entity (and other) classes that implement java.io.Serializable will have issues? thx.

    Note: This thread was originally posted in the Serialization forum, but moved to this forum for closer topic alignment.

  • IPCCX jtapi, add cluster and trigger error

    hi,
    during the installation of ipccx (HA deployment) i found difficulty in adding the cluster and making the trigger. on start it gave me the error of jtapi resync.when i tried to resync it it gave me error (jtapiresyncerror1.jpeg).so i tried to resync it manually by stoping the crs node manager and installing the jtapi client for windows from ccm. but after opening the appadmin application again it gave me error of jtapi sync (jtapierror1). for clustering ipccx1 components are working but when i tried to enable the components of ipccx2 it gave me error (errorafteripccxcomponentactivation1.jpeg)..you can also see other jpegs for reference..it is showing the replication status of unkown.
    then i tried to add the script and application but when i entered the trigger information it gave me error "could not update the user on unified cm" (trigerror1.jpeg)..
    Regards
    Naresh

    hi,
    I haven't tried to install only the second server.. i have time so i reinstalled both the first and second server..following was the sequence
    IPCCX installation:
    1)install operating systems for first server.
    2)install ipccx dvd for first server (after ipccx dvd installation initial setup window will open automatically.. no need to configure it..just close the window)
    3)install sql server..
    4)now open app admin page and do initial setup..
    5)install operating system for second server.
    6)install ipccx devd for second server (after ipccx dvd installation initial setup window will open automatically/.. no need to configure it..just clost the window)
    7)install sql server
    8)now open app admin page of second server and do initial setup..
    hope that it helps..
    Regards
    Naresh

  • 2 Hyper-V Servers with Failover Cluster and a single File Server and .VHDs stored on a SMB 3 Share

    I have 2 X M600 Dell Blades (100 GB local storage and 2 NICs)  and a Single R720 File Server (2.5 TB local SAS storage and 6 NICs).  I´m planning a Lab/developer enrironment using 2 Hyper-V Servers with Failover Cluster and a single File Server putting
    all  .VHDs stored on a SMB 3 Share on the File Server.
    The ideia is to have a HA solution, live migration, etc, storing the .VHDs onm a SMB 3 share
    \\fileserver\shareforVHDs
    It is possible? How Cluster will understand the
    \\fileserver\shareforVHDs as a cluster disk and offer HA on it?
    Or i´ll have to "re-think" and forget about VHDs on SMb 3 Share and deploy using iSCSI?
    Storage Spaces makes difference in this case?
    All based on wind2012 R2 STD English version

    I have 2 X M600 Dell Blades (100 GB local storage and 2 NICs)  and a Single R720 File Server (2.5 TB local SAS storage and 6 NICs).  I´m planning a Lab/developer enrironment using 2 Hyper-V Servers with Failover Cluster and a single File Server putting
    all  .VHDs stored on a SMB 3 Share on the File Server.
    The ideia is to have a HA solution, live migration, etc, storing the .VHDs onm a SMB 3 share
    \\fileserver\shareforVHDs
    It is possible? How Cluster will understand the
    \\fileserver\shareforVHDs as a cluster disk and offer HA on it?
    Or i´ll have to "re-think" and forget about VHDs on SMb 3 Share and deploy using iSCSI?
    Storage Spaces makes difference in this case?
    All based on wind2012 R2 STD English version
    You can do what you want to do just fine. Hyper-V / Windows Server 2012 R2 can use SMB 3.0 share instead of a block storage (iSCSI/FC/etc). See:
    Deploy Hyper-V over SMB
    http://technet.microsoft.com/en-us/library/jj134187.aspx
    There would be no shared disk and no CSV just SMB 3.0 folder both hypervisor hosts would have access to. Much simplier to use. See:
    Hyper-V recommends SMB or CSV ?
    http://social.technet.microsoft.com/Forums/en-US/d6e06d59-bef3-42ba-82f1-5043713b5552/hyperv-recommends-smb-or-csv-
    You'll have however a limited solution as your single physical server being a file server would be a single point of failure.
    You can use Storage Spaces just fine but you cannot use Clustered Storage Spaces as in this case you'll have to take away your SAS spindles from your R720 box and mount them into SAS JBOD (make sure it's certified). So you get rid of an active components
    (CPU, RAM) and keep more robust all-passive SAS JBOD as your physical shared storage. Better then a single Windows-running server but for a true fault tolerance you'll have to have 3 SAS JBODs. Not exactly cheap :) See:
    Deploy Clustered Storage Spaces
    http://technet.microsoft.com/en-us/library/jj822937.aspx
    Storage Spaces,
    JBODs, and Failover Clustering – A Recipe for Cost-Effective, Highly Available Storage
    http://blogs.technet.com/b/storageserver/archive/2013/10/19/storage-spaces-jbods-and-failover-clustering-a-recipe-for-cost-effective-highly-available-storage.aspx
    Using
    Storage Spaces for Storage Subsystem Performance
    http://msdn.microsoft.com/en-us/library/windows/hardware/dn567634.aspx#enclosure
    Storage
    Spaces FAQ
    https://social.technet.microsoft.com/wiki/contents/articles/11382.storage-spaces-frequently-asked-questions-faq.aspx
    Alternative way would be using Virtual SAN similar to VMware VSAN in this case you can get rid of a physical shared storage @ all and use cheap high capacity SATA spindles (and SATA SSDs!) instead of an expensive SAS.
    Hope this helped :)
    StarWind VSAN [Virtual SAN] clusters Hyper-V without SAS, Fibre Channel, SMB 3.0 or iSCSI, uses Ethernet to mirror internally mounted SATA disks between hosts.

  • Ias console and deploy war file

    Hi All,
    I need to deploy a war file into EBS R12. I thought of enable the ias console and deploy. I followed the steps
    1. Change $INST_TOP/ora/10.1.3/Apache/Apache/conf/trusted.conf file and change
    [Location ~ “/ascontrol”]
    Order deny,allow
    Deny from all
    Allow from localhost
    [Location]
    to
    [Location ~ “/ascontrol”]
    Order deny,allow
    Allow from all
    [Location]
    2. Restart Apache
    adapcctl.sh stop
    adapcctl.sh start
    3. Access it via
    http://server:port/ascontrol
    After doing the above steps, am able to open ias console. But when i go to tab oc4j-instances and click on any instance oafm or forms or oacore, its saying an error Error Mesg: Unable to login to the OC4J "default_group" on  Application Server "oacore" the OC4J is not running . I checked opmnctl status, all components are running. Please let me know any suggestion on this.
    Also is there any way to deploy war file from back end. I got one utility like admin_client.jar. but when i try to validate using the following command
    java -jar admin_client.jar deployer:oc4j:<host>:6003 oc4jadmin welcome123 -validateURI .. giving error as below
    Failed at "Could not get DeploymentManager".
    This is typically the result of an invalid deployer URI format being supplied, the target server not being in a started state or incorrect authentication details being supplied.
    More information is available by enabling logging -- please see the Oracle Containers for J2EE Configuration and Administration Guide for details.
    Valid connection_uris are:
    1. To target all OC4J instances that belongs to an OC4J group in an Oracle Application Server Cluster:
    deployer:cluster:[ormis:]opmn://opmnHost[:opmnPort]/oc4jGroupName
    2. To target a specific OC4J instance within a cluster:
    deployer:oc4j:[ormis:]opmn://opmnHost[:opmnPort]/oc4jInstanceName
    deployer:oc4j:[ormis:]opmn://opmnHost[:opmnPort]/asInstanceName/oc4jInstanceName
    3. To target a standalone OC4J server:
    deployer:oc4j:oc4jHost:rmiPort
    deployer:oc4j:ormis:oc4jHost:ormisPort
    opmnPort is the OPMN request port specified in opmn.xml.
    If omitted, defaults to 6003.
    Thanks,
    Manikandan

    Hi;
    Please check below thread than recheck your steps
    Re: Deploy .war file in Ebs 11i-11.5.10.2
    Regard
    Helios

  • How do you package and deploy a resource adapter with a c++ library?

    I am using Weblogic 8.1 and am trying to deploy a resource adapter that has a platform dependent c++ library. This has to be done from a script so I am using weblogic.Deployer. I am failing with a “java.lang.UnsatisfiedLinkError:” I understand that the library is not in java.library.path. I don’t want to have to stop weblogic, set the lib path, restart weblogic, and then deploy. How can I accomplish this?
    thanks

    > In trying to access a dll with the function
    > canWrite
    > (
    > HANDLE handle,
    > CMSG *cmsg,
    > long *len,
    > OVERLAPPED *overlppd
    > )
    >
    > CMSG is a structure
    > typedef struct
    > { long id;
    > unsigned char len;
    > unsigned char msg_lost;
    > unsigned char reserved[2];
    > unsigned char data[8];
    > } CMSG,
    >
    > an error#3:"E:\lv45\mgsource\memory.c line515" is displayed.
    >
    > My question is, how do i get this vi to run correctly without
    > generating the error. Basically, i'm trying to control the esd pci 200
    > can card. i have the c codes and am tryng to write vis with the dll.
    >
    With this additional information, what I'd do about the CMSG is to make
    an array of uInt8 that is sixteen elements in size. You will be able to
    transfer the bytes to and from t
    he array by using indexing. Wire the
    array to the function for the second parameter and set it to pass the
    data by pointer. I have no idea what is supposed to be int he struct
    when the function is passed, but if you cast between a matching cluster
    and the array, you will need to swap the first bytes for the long
    parameter. Same goes for reading the results back from the array after
    the call.
    Greg McKaskle

  • Some error in cluster alertlog but the cluster and database is normal used.

    hi.everybody
    i used RAC+ASM,RAC have two nodes and ASM have 3 group(+DATA,+CRS,+FRA),database is 11gR2,ASM used ASMlib,not raw.
    When i start cluster or auto start after reboot the OS,in the cluster alertlog have some error as follow:
    ERROR: failed to establish dependency between database rac and diskgroup resource ora.DATA.dg
    [ohasd(7964)]CRS-2302:Cannot get GPnP profile. Error CLSGPNP_NO_DAEMON (GPNPD daemon is not running).
    I do not know what cause these error but the cluster and database can start normal and use normal.
    I do not know whether these errors will affect the service.
    thanks everybody！

    anyon has the same question?

  • Automating Sharepoint Foundation 2013 Installation and Deployment of Project

    Hi all,
    I'm a long time software developer with absolutely no experience in Sharepoint.
    I have just joined a new company and I was asked by the team leader to create an installer for Sharepoint Foundation 2013 and a working Sharepoint solution made by the company, preferably using HTA.
    I have experimented installing it manually and deploying the solution, however, what's the best method to automate these two steps?
    I was thinking of something like AutoSPInstaller, and after the end of the installation, I would run Add-SPSolution and Install-SPSolution commands for deploying the solution.
    What do you think?

    So the only problem with SharePoint Foundation is that you cannot script the provisioning of the Search Service, you must use the wizard via Central Admin UI to create it. There is an unsupported workaround, but again, unsupported so I don't use it.
    I'd stay away from HTA and go just pure PowerShell prompts, myself though.
    Trevor Seward
    Follow or contact me at...
    &nbsp&nbsp
    This post is my own opinion and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

  • Problem with packageing and deploying a sample application

    HI,
    I have tried to download and install the server in my system. I am able to deploy a sample application using autodeploy utility.
    But when i tried to package a new sample application and deploy i am getting 404 error. For application server i have used 7070 port and not the default 8080 port will this a problem to package & deploy sample application provided with this software.
    The error is as below:
    HTTP Status 404 - /hello1
    type Status report
    message /hello1
    description The requested resource (/hello1) is not available.
    Sun-Java-System/Application-Server

    Btw, verify that the url you are trying to access is correct. For instance, assuming you deploy app. without --contextroot option. By default,  the url is http://<host>:<port>/<web module name>/<value of url-pattern in web.xml> if your app contains servlet. If your app has jsp then it's http://<host>:<port>/<web module name>/<value of url-pattern in web.xml>/<name of jsp>                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                               

  • VS 2010 Pro "Other Project Types" / "Setup and Deployment": No items found

    Hello,
    I have VS 2010 Pro Version 10.0.40219.1 SP1 Rel. I have developed a VB.Net application and would like to deploy it. When I try to add a setup project to the solution, I get "No items found" where a list of project types should be in the "Add New Project"
    dialog, "Installed Templates", "Other Project Types", "Setup and Deployment". Shouldn't the Pro version have those templates installed? If so, can I copy them from somewhere? I noticed that "Database" and "Test Projects" also have empty lists. There are lots
    of templates available for the various languages.
    I tried to modify the VS 2010 installation by adding support for SharePoint, but that did not help. Do I have to uninstall, reboot, and re-install? It's so cumbersome considering that I would need to redo the updates as well.
    OS is Win 7 Pro, processor is Intel E8400.
    Thanks!
    r4

    Hi robertrackl,
    Thanks for your post.
    The Setup Project template is located in: Installed Templates >> Other Project Types >> Setup and Deployment >> Visual Studio Installer. Would you please check if the templates exists in this path?
    If not, you can follow the steps below to reset your Visual Studio templates:
    Please open Windows Explorer, and navigate to <Visual Studio Installation Path>\Common7\IDE
    (by default is C:\Program Files \Microsoft Visual Studio 10.0\Common7\IDE);
    Delete the ItemTemplatesCache, ProjectTemplatesCache
    folder;
    Open Visual Studio Command Prompt (2010) under Start menu -> All Programs -> Microsoft Visual Studio 2010 -> Visual Studio Tools (run it with Administrator privilege: right-click the program -> Run as administrator);
    Run the devenv /InstallVSTemplates switch;
    Run the devenv /Setup switch.
    If you have any concerns, please feel free to let me know.
    Best Regards,
    Andrew Wu [MSFT]
    MSDN Community Support | Feedback to us
    Get or Request Code Sample from Microsoft
    Please remember to mark the replies as answers if they help and unmark them if they provide no help.

  • Display image in forms & reports developed on windows and deployed on Unix

    Hi,
    We are upgrading from Forms and reports 6i to forms10g.
    We need to insert image in forms and reports. Recompile and deploy on unix server.
    So can anyone let me know the exact steps to create jar file containing images, where to place the jar file.
    Corresponding folder, file and configuration changes required on windows and unix.
    Av.

    Hi Frank,
    thanks for the link it helped me in understanding how images work for forms.
    But my real concern is how this will work in reports?
    As we dont have any reportsweb.cfg nor any java path for reports?
    Can you help me in understanding how to embed image in reports that will be displayed even after porting the report on unix oas.
    Regards,
    Av.

  • How to add a new Shared Variable programmatically to an existing and deployed library?

    Hi there!
    I am trying to accomplish this on both LabVIEW 8.6 and LabVIEW 2010 and seems like it's not any different in this situation.
    My case: A project has a library with 4 Shared Variables (SVs). The library and the variables are deployed (visible in Distributed System Manager 8.6/2010). I want to add 2 more variables into this library. It is possible to do this manually from Project Explorer window's options menu. But while running an application it has to be done programmatically. Can I provide the library reference to the one currently existing without creating a new one?
    "Create Or Add Library To Project" function in the Datalogging and Supervisory Control (DSC) toolkit does not help in this case. That function, as the name suggests, just tries to create a new library in the project.
    Two possible methods:
    The function "Add Shared Variable To Library" (DSC>EngineControl>Libraries & Processes) needs a library reference, which could be provided via "CreateOrAddLibraryToProject" function, but this function tries to create a new library, and if I provide the path of the existing library it throws an exception that the library already exists in the project (yes, as I wrote above, I need to add new variables to an existing and deployed library).
    OR
    The function "Create Shared Variable" (DSC>EngineControl>Variables & I/O Servers) will add Shared Variable in a process, and not physically in a library file, and the problem (limitation) with this approach is that it doesn't allow to add complex data type Shared Variables (for example in LabVIEW 8.6 it has only 4 datatype options in input parameter, and even in LV2010 it does not have "Image" datatype that I need).
    The scond method is my preferred method as it allows to work on Online Shared Variables and doesn't create them physically in libraries (and this is good as the variables' scope remains only till the Variable Engine is running). But it doesn't support advanced data types, and the first method is powerful in terms that it supports to virtually any datatype, it just seems tricky to get that reference to the library.
    Any tips?
    Thanks ahead!
    Vaibhav

       <<<<>>>>   
    As the above two images show, while a library does not exist, it is easy to use the "CreateOrAddLibraryToProject.vi" which will add a new library to the project (if it doesn't exist on file system, a new library will be created) and that way, using the reference (the green wire going out from the function and the Case Structure, can be used to add Shared Variables to the library. The problem was what to do when a library already exists in the project, how to add more variables to it. I was looking for a way to get a library reference, and somehow I could not see it inside a Project's property (VI Server functions). Hence I posted the question. And upon continuing my search, I found it on the Application's property list.
    I hope it was useful for someone else as well. And thanks for the replies. Please share a better idea if you have.
    Vaibhav

  • Is there any way to back up a preconfigured iPad and deploy to new iPads using Configurator??

    To clarify,  we have about 100 ipads deployed in our district and lots more on the way.  We had just used iTunes in the past to backup one master device with the apps and restored on the remaining sets of iPads.  Obviously we wanted a simpler way to manage this as we are getting a lot more iPads coming in for use in the different schools.  We got a MDM solution (Casper) and started using Configurator.
    We are running the latest of Configurator (1.4.2) and IOS (7.0.4).
    From what I have read (and a lot at that) I know that there are numerous issues with this setup (hopefully addressed very soon)
    Here is my question:
    Is it possible to take an already deployed device, loaded with apps (paid and free), back it up in Configurator, and deploy it to other iPads and still get all the apps to come down along with the restore?
    Apparently this was possible in the past, I am just wondering if I am missing something.  Any help or suggestions on how you are doing it would be very helpful
    Oh, and to clarify, we are using VPP for the apps, just not managing them any where at this time, haven't decided the best tool for that, maybe casper maybe configurator, but we are compliant, only using the same quantity of apps that we have purchased.
    Thanks
    Edit: spelling error

    I've heard if you contact your apple rep, Apple may restore your vpp codes so you can move to an MDM.
    Read the Google doc below and nsdjoey write up.
    IT Resources -- ios & OS X -- This is a fantastic web page.  I like the education site over the business site.
    View documentation, video tutorials, and web pages to help IT professionals develop and deploy education solutions.
        http://www.apple.com/education/ipad/resources/
        scroll down after all the pretty picture.  Click on the words "For It".
    Joe Rowe's Excellent guides
    IT managers who are new to configurator and managing a cart of ios devices:
          https://docs.google.com/document/d/1SMBgyzONxcx6_FswgkW9XYLpA4oCt_2y1uw9ceMZ9F4/ edit?pli=1
             [ original announcement  -- https://discussions.apple.com/thread/4256735?tstart=0 ]
    Quick help presentation for students:
         https://docs.google.com/presentation/d/18937JdleX2gymtSb8zfbDczV-76BdR2DIfCV9eJi yOE/edit#slide=id.g1b776944_0_224
    good tips for initial deployment:
    https://discussions.apple.com/message/18942350#18942350
    https://discussions.apple.com/thread/3804209?tstart=0
    See nsdjoey writeup.  See third post.
    https://discussions.apple.com/message/22286109#22286109
    "Deploying a great quantity of iOS devices means creating a great quantity of Apple IDs. This script allows automated Apple ID creation from a spreadsheet."
    http://www.enterpriseios.com/wiki/Apple_ID_Automation_Builder

  • How to create a custom ear file and deploy it onto a freshly created oc4j

    Hi,
    Wanted to know that how should i go about creating a custom EAR file or for that matter any application and deploy it onto a test oc4j instance created within the 10.1.3 Home of Oracle Apps R12.
    I believe in a standalone Application server installation it is quite simple to deploy an application by creating an oc4j instance using the AS console ,but not very sure about how to go about it in Oracle Apps .
    N.B:I have been able to create a test oc4j instance by the name of Test and able to start and stop it using the opmn of 10.1.3 oracle home.
    Any help in this regard will be appreciated.

    Hi,
    can you please post this question to one of the Apps forums if your main concern is to deploy applications in the context of Oracle Apps?
    It seems that you don't have a problem in creating the EAR file in JDev.
    Frank

Maybe you are looking for