Cluster continues with less than half voting disks

I wanted to try voting disk recovery. I have voting file on a diskgroup with normal redundancy. I corrupted two of the disks containing the voting disk using dd command. I was expecting clusterware to be down as only 1 voting disk ( < half of total(3)) was available but surprisingly clusterware kept running. I even waited for quite some time but to no avail. I did not have any messages in alert log /ocssd log. I would be thankful if experts can give more input on this.
Regards

Hi You can check the metalink notes
OCR / Vote disk Maintenance Operations: (ADD/REMOVE/REPLACE/MOVE) [ID 428681.1]
it says
For 11.2+, it is no longer required to back up the voting disk. The voting disk data is automatically backed up in OCR as part of any configuration change.
The voting disk files are backed up automatically by Oracle Clusterware if the contents of the files have changed in the following ways:
1.Configuration parameters, for example misscount, have been added or modified
2.After performing voting disk add or delete operations The voting disk contents are restored from a backup automatically when a new voting disk is added or replaced.

Similar Messages

  • Updated my 3gs to 5.0.1 and my battery life has gone from 1.5 days   to less than half a day with no Apps open - how can I roll this back to 5.0 until a fix comes out?

    Since updating my 3GS to 5.0.1 my iphone battery has gone, overnight, from 1.5 days + (with multiple open Apps) to less than half a day to completely discharge from 100%.
    I desperately need to roll this install back to 5.0 but there are no resources on the internet (or this site) which indicate how I would do that.
    Please help.
    J

    You cannot and should not go back to 5.0.
    A fix is coming soon

  • My iPhone 4s shuts down with just less than half the battery remaining

    My iPhone 4s shuts down with just less than half the battery remaining. Is my battery shot?

    Hi LucMiranda,
    Thanks for visiting Apple Support Communities.
    It sounds like your iPhone is not behaving correctly. The steps in this article can help with troubleshooting the battery issue you're seeing:
    iPhone and iPod touch: Charging the battery
    http://support.apple.com/kb/HT1476
    iPhone or iPod touch displays the low-battery image and is unresponsive
    If you see the image below, charge the iPhone or iPod touch with USB power adapter for at least 15 minutes.
    You should see this image when iPhone or iPod touch begins to charge:
    If the screen still displays the low-battery icon, try turning the iPhone or iPod touch off and then on again.
    If the issue persists, follow these troubleshooting steps.
    Cheers,
    Jeremy

  • HT1848 On itunes, when synced to my pc, I show less than half of the music that is on my iphone 4. How do I get all the music onto my pc?

    I am about to scream if I don't figure this out or just decide to leave Apple and get a Galaxy phone. On itunes, when synced to my pc, I show less than half of the music that is on my iphone 4. How do I get all the music onto my pc? I have read many forums and tried many things, but apple/iTunes is not intuitive at least not on a PC. When I go to devices it won't let me select "transfer music". It's grayed out. Why is this and what can I do? I'd like to delete some of the music off of my iPhone but don't want it gone forever. Pleae help.

    Thanks Turingtest2,
    I appreciate your response. I have done all of the things mentioned, but still when I click on "devices", the "transfer music" option is still not selectable. I see it, but can't select it.  I am running Windows 7 on my PC.
    However, one thing I read makes me take pause. At one point I did erase my computer back to factory settings using the mirrored image. We backed up all information and put the important stuff back on, but I don't believe we did anything with iTunes, so it's a possibility that the music that is in my library now, may only be music I have purchased since then. But, (thinking out loud) that was a while ago and I am pretty sure I have purchased more music than what is in my iTunes library, since then.  Maybe I will approach it from that angle and see what happens.
    It just doesn't make any logical sense that syncing goes from computer to device. Ostensibly then, my iPhone would only have the music that is on my computer after syncing and that is not the case. I still have all my music on my phone. I can see the new music that's on my phone get added to my iTunes library when I connect, which would make one think that syncing occurs both ways. I don't know. It's maddening. Maybe I should just follow my husbands advice and go to an Android. LOL. Or maybe I will take my laptop and phone to the Apple store and make them figure it out. Ha.
    If you have any thoughts about this, let me know. Thanks again.

  • After prompted to update 10.9.1, my MacBook Pro updates and went thru restart but failed...I tried to start my book and gray screen, Apple logo both on, chime sounded, then went to progress bar, less than half macbook shuts down...did few times, same!!

    After prompted to update 10.9.1, my MacBook Pro updates and went thru restart but failed...I tried to start my book and gray screen, Apple logo both on, chime sounded, then went to progress bar, less than half macbook shuts down...did few times, same!!
    Go to system repair, there is a prompt that cannot repair live etc....I don understand!!! Help, I need the book for work tomorrow!!

    Thanks clintonfrombirmingham...
    After clicking "repair disk" it says DISK UTILITY STOPPED REPAIRING MACINTOSH HD, DISK UTILITY CAN't REPAIR THIS DISK. BACK UO AS MANY OF YOUR FILES AS POSSIBLE, REFORMAT THE DISK, AND RESTORE YOUR BACKED -UP FILES....
    written in red: ERROR: DISK UTILITY CAN'T REPAIR THIS DISK,,,DISK, AND RESTORE YOUR BACKED-UP FILES.
    how can I back up when I cannot even start my macbook? I am stuck here and have lots of important files in the hd... Please help me? Thanks you!

  • Set mpeg resolution to less than half?

    Is there any way of setting the mpeg resolution to less than half? I ask this because I want to use the program strictly for HDV real time monitoring (not recording) and it seems like the latency is most affected by the mpeg resolution.

    No, Half-Res is the only option. Is your CPU getting pegged while monitoring HDV at half-res? If not, then a lower res setting wouldn't help.
    A major factor in latency with HDV is the interframe compression. There's a big random element to the extent of the latency depending on where in the GOP OnLocation starts getting frames. So if the latency is especially bad, cycling power on the camera might help. It's pure luck of the draw where you step into the GOP data stream.

  • Migration stalled with "less than a minute remaining"

    This issue was discussed back in April, but no definitive solution was found.
    I installed Mountain Lion on an older MacBook Pro and all went well until I got to the Setup Assistant after restart. The migration of my files from a Time Machine backup stalled with "less than a minute remaining" while "transferring files to support applications". Apparently this is a known issue that affects older Macs upgrading from Snow Leopard. I have two questions about this:
    1. Can anyone suggest a fix or workaround for this problem? In the earlier thread, some people repeated the file transfer several times with exactly the same results. One person evidently had better luck when he started over and deselected everything but Users on the transfer options screen; but it obviously requires alot of extra work on the user's part to reinstall every application.
    2. What is the best way to abort the stalled transfer without risk of damaging the data on my Time Machine backup drive? Mountain Lion refused to install on my startup drive until I erased it, so my Time Machine backup is the only copy I have of my data. Since Setup Assistant is not frozen, I can hit command-Q and Setup Assistant offers to shut down; but is the data on my backup drive at risk if I shut down and start over?
    Thanks!

    Has your Migration Assistant actually crashed? I am restoring my computer from a hard drive failure and the following dialog has been displayed for the last 12 hours. I clicked on the App in the dock to see if it was displaying as crashed, it doesn't appear to be.
    I checked the "Get Info" on the Hard Drive Volume, and it is showing a very slow progression of used bytes. I suspect the transfer is still continuing, just very slow as I have so much data. I think it is a matter of quanity of files rather than "file size".
    Should be interesting to see in another day or so to see if it completes. :-)

  • Photosmart 5520 showing new cartridges as less than half full

    I've just replaced the three colour cartridges with genuine HP cartridges.
    There are no printing problems, no error message, yet the Cyan and Blue cartridges are only showing less than half full. The yellow one is showing full.
    I've tried all the steps on the trouble-shooting page here  but no change.
    Is there a solution?

    Hi gordonbp,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I see that the colour ink cartridges are not giving an accurate reading. I do have a couple troubleshooting steps that I would like to run through to see if we can get this issue resolved for you.
    First off, if you have the printer power cable connected to a power bar/strip, please remove it and connect the power cable direct to a wall outlet.  Here is a document that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.  Please note that the printer that is listed in this document is a LaserJet printer and that this is only used as an example seeing that the power issue applies to HP products in general.
    I would also suggest that you attempt to reset the printer once the power cable is in a wall outlet. Here is a document that explains how to do a basic Reset on the printer.
    Thank you for your time.
    Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    W a t e r b o y 71
    I work on behalf of HP

  • EPM 2013 Report is displayed as cut off and shows less than half the width of the report in IE 10 and IE 9.

    EPM 2013 Report is displayed as cut off and shows less than half the width of the report in IE 10 and IE 9.  This issue occurs for some users only.I tried the same url in google chrome and is working fine.
    Can you please help.
    Please find the attached screenshot.

    Hi BJ1986,
    According to your description, I think this issue is caused by the IE browser that runs the report. To trouble shoot this issue, I suggest that we can try to clear internet temporary files, cookies and others in IE browser. And also add this site
    as a trusted site in IE browser to check this issue again.
    If this issue is still existed, it can also be occurred due to the setting or third party add-ons of Internet Explorer (IE). In this scenario, you can try to run IE in compatibility mode to check the issue again. Or I suggest that you can refer to the
    steps below to troubleshoot the issue:
    Click Tools -> Internet options.
    Switch to the Security tab, click Local intranet, and then select Default level.
    Switch to the Advanced tab, and click Restore advanced settings.
    Temporarily disable third party add-ons. For detailed steps, please see the link below: 
    http://windows.microsoft.com/en-IN/internet-explorer/manage-add-ons#ie
    Hope this helps.
    Thanks,
    Katherine Xiong
    Katherine Xiong
    TechNet Community Support

  • Small office with less than 10 APs

    What is best way to handle or setup wireless connection for a small branch office with less than 10 APs?  Management doesn't want to spend any money to install a local WLC.  Those APs will communicate back to two WLC 5508 in Data Center.
    Should I use local switch or flexconnect?  Any one has experience about pro and con between those two methods.  Ping time between branch office and Data Center is less 60 ms.
    Thanks,

    What is the link bandwidth between those two site. If you have enough bandwidth then you can go for local mode deployment, but all CAPWAP traffic has to come Data Centre WLC (ie central switching)
    If you would like to terminate branch traffic at branch switch, then FlexConnect local switching is the way to go.
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • I have swapped my itunes to a new laptop instead of my poor old PC, however less than half of the albums have transferred. They were not purchased on itunes

    Please help, I am getting rid of my poor old PC and have tried moving my library to a laptop, however less than half of my music has appeared. How do I sort this easily?

    There should be an option to sync purchases from the iPod to iTunes.
    See this -> Copying iTunes Store purchases from your iPod or iPhone to a computer
    i cannot re-download them for free
    Yes you can.
    Click on Purchase and iTunes will tell you that you jhave already purchased then and ask if you want to redownload them (for free).

  • Encoding issue with " " Less than sign

    Hello Experts,
       I am working on Receiver Webservice scenario where I am facing issue with "<" less than sign. SAP XI system automatically replace it with "&#60;" sign. I can see the changed value in Audit log of communication channel.
    Web service is not able to accept the data and I can see error message in audit log
    SOAP: response message contains an error XIAdapter/PARSING/ADAPTER.SOAPEXCEPTION - soap fault: Server was unable to read request. ---> There is an error in XML document (1, 573). ---> The specified node cannot be inserted as the valid child of this node, because the specified node is the wrong type._
    When I check the payload in audit log I can see the XML structure properly but as I open it in Notepad I can see character code "&#60;" instead of  u201Cless than <u201D symbol.
    Audit log XML file is as given below
    <?xml version="1.0" encoding="utf-8" ?>
    - <ns1:TurnaroundDetail xmlns:ns1="http://isotrak.com/webservices">
      <ns1:sessionid>3f2f2592-39d5-456e-8cf2-5d7ee81402c8</ns1:sessionid>
      <ns1:data><Request xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"><TurnaroundDetail><PlannedJobDepartureDatesFrom="2011-03-01T12:01:23.00" To="2011-03-01T12:07:10.00"/><DepotReference DepotReference="EASTLEIGH"/><DepotReference DepotReference="CHANDLERS"/></TurnaroundDetail></Request></ns1:data>
      </ns1:TurnaroundDetail>
    When I open it in notepad I can see converted value
    <?xml version='1.0' encoding='utf-8'?>
    <TurnaroundDetail xmlns='http://isotrak.com/webservices'><sessionid>dcc4adcd-ce8f-403d-a1cf-01fcc5aab066</sessionid><data>&#60;Request xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">&#60;TurnaroundDetail>&#60;PlannedJobDepartureDatesFrom="2011-03-02T08:28:29.00" To="2011-03-02T08:38:09.00"/>&#60;DepotReference DepotReference="EASTLEIGH"/>&#60;DepotReference DepotReference="CHANDLERS"/>&#60;/TurnaroundDetail>&#60;/Request></data></TurnaroundDetail>
    I hope this is not caused due to AnonymizerBean configured in receiver SOAP comm channel.
    anonymizer.acceptNamespaces   http://isotrak.com/webservices ''
    anonymizer.encoding  ISO-8859-1 (also tried utf-8)
    anonymizer.quote  ''
    Could you please suggest if I can get rid of "&#60;" character and get < less than sign? Or it is obvious behaviour by SAP XI system w.r.t Encoding and Receiver end needs to decode this character?
    Note: As per Web service requirement whole XML data to be processed by webservice is populated in single Data field. As here we are populating whole XML data file in one field named data
    Thanks in advance.
    Vinit.

    Simply typing "Test <test> test" into a frame and exporting that yields
    <ParaStyle:Body>Test \<test\> test
    and reading it back into ID gives the expected result.

  • Issues with less than and grater than condition in prompts in OBIEE 11g,

    Hi all,
    i am facing the prombles with less than grater than conditions in OBIEE 11g.
    i created two date prompts with presentation variables datefrom and dateto
    and i used these prompts in fileters like this using grater than and less than symbol.
    filters are as below:
    lastupdated date is grater than or equal to @{datefrom}{1/1/1950}
    lastupdated date is less than or equal to @{dateto){1/1/1950}
    and created two prompts
    creation datefrom >=
    creation dateto<=
    when i passing the dates 05/12/2004 and 05/12/2005 in prompts after clicking the apply button in OBIEE 11g it feches all the records but i need records between these dates. and one more thing is after clicking apply button the two date fields getting the same date..
    am i do any thing wrong in the above ???
    please let me know friends..
    waiting for ur replyyyyyy..
    Thanks
    Edited by: BI_user on Oct 12, 2011 2:10 AM

    Hi,
    Create date prompts with operator as = not >= (or) <= as you need to save that value in presentation variable and you are filtering report using those variable filters.
    Regards,
    Srikanth

  • Albumart for albums with less than 5 songs?

    So i REALLY would like to see the albumart on albums (for instance EP's, singles) with less than 5 songs. Is there any Terminal line to do this?

    When iTunes does not pick up artwork or the wromg artwork I usually just google image the albume and copy artwork, 500 x 550 is perferred if you want to use jukebox or large image, don't bother with anything under 300 x 300 as it will be blury. Go back into iTunes highlite all the songs on the album, right click and paste into the album art square.

  • I bought a new Iphone 5 Friday the battery goes flat in less than half a day also the wifi disconnects in less than 40 secs

    I bought a new Iphone 5 Friday the battery goes flat in less than half a day also the wifi disconnects in less than 40 secs this is really frustrating I think I have a dud phone or is this the new IOS6.1 software update?

    Basic troubleshooting steps clearly outlined in the User Guide are restart, reset, restore from backup, restore as NEW device.  If you've been through ALL the steps listed and you're still having problems, then you'll need to bring your phone into Apple for evaluation and possible replacement.

Maybe you are looking for