Clustered Environment - Changing from Public Network to Private Network
I have a clustered environment where the database sits on one node and the central instance sits on the other node. We just found out that somehow the communication between the database and central instance has been changed to talk over the public network instead of the private network. We don't know who did it or why.
So, my question is what do I need to do in SAP to accomodate the changing back to using the private network? Do I need to change system names in the profiles? Are there any gotchas on doing this? Are there any documents on doing this?
Thanks for any information you can provide on this topic.
Thanks,
-- Jackie
This is most likely a name resolving problem.
If you ping <name> from one server to the other, which network is used?
Markus
Similar Messages
-
Jabber login from public network not working
Hello all,
i am trying to register jabebr from public network with use of EXP-C and E.
but facing below error:thanks fro your response to correct me with configuration.
1) Configuration as it pertains to the design on the Expressways
i applied as per design and still open all ports between firewall for jabber.
2) Firewall blocking the UDP traffic.
if no rule define, how can it block and what need to configure for jabber with audio?
First question to you is are you using Single NIC or Dual NIC on the Expressway-E?
i am using single NIC.
If you are doing a Single NIC design and will have a private IP for the Expressway-E you must fulfill these 4 requirements
1) Static NAT Mode Enabled on the IP Configuration page of the Exp-E
i will enable it on EXPE>.
2) Static NAT Address Configured on the IP page of the Exp-E
what need to EXPE for this NAT option?
3) Expressway-C must resolve the Expressway-E FQDN to the Public IP, not the private
if this is resolving private ip, would be any problem?
4) NAT Reflection (Hairpinning) must be configured on the firewall so that traffic from the Expressway-C can be sent to the Expressway-E public IP and that can be redirected to the Expressway-E private IP. Please note not all firewalls support this functionality
please tell me how can enable NAT reflection on firewall to working it?
thanks -
Change from Hidden Network to one that shows?
How do I change my "hidden network" settings? I hid my wifi network and now I can't find a way to make it show. I have a friend with a pc who wants to connect to my network when he's here but my network is hidden and doesn't show up on his laptop. How do I return it to the original setting when my network shows (or how do I tell a PC user how to log onto a hidden network?) He doesn't seem to have an option to enter the name and password of any network. Just those that are not hidden are available to him and we can't access those as they are locked. Thanks.
You can "unhide" the AirPort Express Base Station's (AX) wireless network via the AirPort Utility.
(ref: AirPort Utility > Manual Setup > AirPort > Wireless > Wireless Options > Create a closed network (uncheck)) -
Server 2012 R2 - Change network location from public to private
I am having an issue with changing Network location to private from Public on Server 2012 R2 X64 .
Please note all the reference for previous servers for fixing this issue does not work on 2012 R2.
I am using Static-IP and "Workgroup" as domain setting.
In 2012 server by Right clicking on Network and Turn sharing on or OFF worked but in 2012- R2 Right click is not working not providing turn sharing ON or OFF option.Check if you can change from here :
Run -- Gpedit.msc-- Open Computer configration -->Windows Settings -->Security Settings -->select Network list manager policies
Arnav Sharma |
Facebook | Twitter Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other
community members reading the thread.
NO it did not work I had already tired and rebooted it does not work. Just for other having the same issue please note my Build is 9600 so this may not apply to you,if you have a different Build you might not have this problem.
I am going back to server2012 rather using R2. -
Windows 7 RC - I can't change my network from public to work
After a lot of job, I connected my W7 beta PC with my XP PC, but when I upgrade to W7 RC, I am unable to do this.
I have two net adapters: one linked to the internet cable modem and it is OK (public network). The other linked with a switch but W7 assigned this as unknown public network and I can't change it to home or work network. In W7 beta I assign a work network and it worked.
Thanks.SOLUTION :
WINDOWS 7 WILL AUTOMATICALLY TAG THE CONNECTION AS UNDEFINED NETWORK WHEN IT IS UNABLE TO DETERMINE THE TYPE OF THE CONNECTION AND YOU ARE NOT ALLOWED TO CHANGE THE NAME AND TYPE OF THE NETWORK
The possible reasons are :
a. You are connecting to a network with TCP/IP configuration to automatic but the network doesn't have a DHCP server;
b. You configured the TCP/IP manually with static values but didn't specify a Default Gateway;
The possibles solutions are :
a. you are using dynamic IP, so you have to set up a software DHCP server on the 2nd subnet
b. you are using static IP, so set up a default gateway on the 2nd subnet NIC
( Source : http://windows7forums.com/windows-7-networking/4416-how-change-network-type-2.html )
Hope this helps ^^
This solution works -- but unfortunately it requires the other network adapter to be on DHCP. If you want two adapters with fixed IP, you get messages that having two default gateways "does not work properly". I tried it anyway -- this resulted in an unreachable internet via router. This all is in Win 7 RC, I will try it on a RTM (Ultimate) in a few moments, but I'm not expecting an improvement.
There is one thing you can do to ignore the problem without most of the negative aspects: turn off the firewall for your "private" network adapter. I don't see much danger here as that's roughly what would happen anyway if you could set it to private.
Having one line set to DHCP (to the router) and the other to use fixed IP will also not be without side effects. Suppose the DHCP line is only 100 Mb, while the internal net uses 1Gb. This will result in all network trafic using a computer name to pass via the 100 Mb line, which is probably not what you wanted. Maybe you could remedy that with a route command; but I have not succeeded in a non-temporary solution to this as the routes are not kept across reboots -- any help welcome.
Getting a DHCP server into this business will also not solve the problem, because then this computer needs to be online all the time, which is not what I would want. If your router (like mine) provides DHCP, you also get problems, because having two DHCPs will usually get you into trouble (this I read from other posts, never did it myself.)
Whoever is responsible for this mess at Microsoft should either provide a very good explanation or preferably fix it as fast as possible.
Maybe I don't understand you, but, if I have a router I don't need to use two adapters, I simply use the router as server and connect all of my computers to it. -
Cannot change active network from public to home in Windows 7
Hello, I have just installed Windows 7 RC 7100. I have a netgear fa311 network card, which it did not automatically install. I manually installed the drivbers and now it has identified my home network as a "Public network" so I can not connect to the internet. I can't seem to find any way to change this to the "Home network". Can anyone help please?
Hello, Tried that! The"Public network" text is not a link!! Not here on this pc anyway! The ip address I have is 169.254.172.117 with a subnet mask of 255.255.0.0
May 25 2012 23:03 win7Ultimate update from HomeP LicenseID_5_ sys pack1
May 26 2012 10:18 ~ 10:28 win7U5 sp1
May 26 2012 11:21 ~ 11:29 win7U5 sp1
May 28 2012 04:10 ~ 04:43 Win7U5 sp1
July 3rd 2012 08:13 ~ 08:36 win7U3 sp1
July 05th 2012 16:24 ~ 16:33 win7U3 sp1
July 06th 2012 12:43 ~ 12:53win7u3sp1
July 07th 2012 13:29 ~ 14:00 win7u3 sp1
July 22 2012 ~ 09:04 win 7 p h sp1
Aug. 06 2012 10:33~10:48 win7h sp1
Aug. 25 2012 08:12~ 08:53 win7U_6 sp1
Hello Mr. Darene Lewis and Ellerdch,
Remember you have emailed the *.etl file to Darene Lewis . May I know how you did that from here , the technet.microsoft forum please? I have been asked same IPV4 Question from him. However, there is not found attach way from this perusal.
They are either image , HTML or appliance software model.
No option for *.etl sending .
--------> *.elt could be built in Hyperlink first then attach_link to you [July 07 2012 13:30]
TO modify the Networks , some next places maybe need pay attentions first ...
0) Connection via WLAN or LAN; Router or Modern or else
'0.1) "MULTIPLE NETWORKS" means too many things ... router, interface, communication category as well their configurations so on ...
it is not simple "unidentified Network " change to Home or workstation network ? !
1) Network Share Center \ chose home and network option
2) Anti_Virus FireWall's Inbound:Outbound settings
3) Microsoft Computer \ services settings
4) Dos Administrator \ netsh ? settings
4.1) Powershell \ settings << Dos cmd , why?
4.2) netsh ras > except PPPoE 1 that is my registered wanport, there are as many as 8 more connection available like pptp, etc... they are indeed
running ? Although in Router configuration , PPTP already has been set to "deny" ?
5) Search \ secpol.msc settings
6->) Why the default network ISP giving connection retained reserving at MULTIPLE
NETWORK which is under the search now.
May 26 2012 10:48 win7U sp1
May 26 2012 11:09~11:14 win 7 U sp1
Multi_monitor performance on Win 8 only , if my PC has been taken Authority to do so, then
the System Security has been ruded.
PASSWORD attentions included : ANTI_virus Tool, Microsoft Fire Wall, HDD password,
Windows logon Password, Usual Appliances Password Protection such as Lenovo's CSS etc...
Ref: cc722518.aspx_file by Microsoft
This article described how a server configure its up to five IPs from the NT Server.
My PC client has been merged by NT as its Client . Since my PC now connecting internet
THROUGH Multiple Network.
It is either using my ISP authority on Win 8 for multi_monitor or playing NT server . It just
treat me as one of its clients.
How can I fix this , try hard Julie by yourself?
"Advance IP Address nowhere to find [as it is for Server parameter], this is for NT server to
configure the IP intranet more than one address to access different servers at routine situations.
Ref:cc451515(v=WS.10).aspx_files Microsoft
Multiple network adapters 2 out of 2 rated this helpful Updated: January 21, 2005
Applies To: Windows Server 2003, Windows Server 2003 R2, Windows Server 2003 with SP1,
Windows Server 2003 with SP2
quato "The cluster adapter handles client-to-cluster traffic using the virtual IP address. However
host-to- host traffic within the same cluster is not
possible on this adapter because the MAC address for each host in a particular cluster is the
same. For more information, see Address Resolution
Protocol (ARP)."
FIFS is the basic law here in the INTERNET world.
Since the IPV6 has not be able to work to identify each of us except Client join to Domain own
personal IP from NIC.
Some Domain like Best domain, FatCow simple issue C Luster called it to us.
That is why My client PCs has been unnoticed connected as Multiple Network by Servers.
----> very likely Modern ISP output has been occupied by Wireless redirect who roler as Server ,
maybe using win 8 or NT . Many prompted cmd not be able to configuration on my Win 7 U.
netsh advfirewall> check found 7 NL there.
7) The Authority abuse accident under monitoring by Anti_Virus and Microsoft, Lenovo,
Router_syslink Companies REF_15) 16)
8) Power shell another place to care the setting
9) Route Setting for advance appliance on Intrude Protection approaches etc...
11) AAA [Authentication, Authority, Account] management, correlated with Multiple Network
somehow,Reference for 6) 15) 16)
Authentication has had problem to protect Password for a quite while. Which is probably merged
with MIL appliance that noticed.
------> CSS reset can solve this.
------>E-certification with Microsoft function connection setting solve this ..
With Password manager of Lenovo , it will lose features of Certification migration as well, the
Phrase advance Security Protection THAN "Client Security Solution" by Lenovo
Therefore, CSS (instead Password Manager) can be intruded at that time probably by " some "
12) The beneath Error contacting ISP still stay with Modern VSDL :( REF_ 15) 16)
13) Having been questioned whether am I installing switch or NT server on the router ...
Three are be some symptom indicated that but unable to be ? Agency said just ask briefly after
repeated .
13-0) [802.1x allow wire and AP wireless access point to flow through PC although
Authenticator both]
13_1)MY XP motherboard [UUID:80BC1E5333640010AEC1C8D08A1DEE15/M:8425LB9/SN:]
has been lost nearly two years which can play as NT server. Switch is nothing device
for me . ANY detective on it by organization or personal would be rewarded.
14) ACS [Authentication Control Server] control Modern ISP output signal definitively , the Contract
description on web server Plan is one of main reasons? THE ISP insist not to change it right while
trail_case follower Mr. resigned this week.
15) ISP suppliant Speed critical factor upon whose get Authentication first then , the ICMP action ?
15-1) Why my ISP plan 30M , shown connection speed but100M
15-2) In fact, the ISP has not rendered me right Order Product appropriated with the PLAN for
over one year from very beginning. That is one of why ACS can't detect me well. On side of both contract and exclusively
offering VDSL modern
15-3) e-certification secure the connection however, clear text transaction hole also.
16) With Cisco Router, it seemingly connected Internet as the Model unable find input is
Wire/Wireless signal. Having to proclaim is my PLAN is
Wire_30M_5G ordered at Mar.2011
16-0) There is fe:: ipv6 address likely address through the [adapter teredo pseudo interface] by ipconfig , obviously told me wireless through ?
16-1) By only ISP Modern , there is indeed NO Internet that is why the Screenshot down.
Then why at this condition, browser internet looks OK? Because the Wireless [multiple
Local connection] Ref_15 took the Authentication_Account first, secondly, Created
call AD_HOC wireless function to make the all networking devices on net that is
INTRANET.
16-2) @OFCA.gov.hk, local communication Management , is negotiating with ISP locally for one week since June 27 2012 received
the report. Only contract it working on , last contact at Aug. 2nd 2012 retaining along with ISP company today Aug. 25 2012
17) Have you thought of PC purchase area and location bringing you something differences ?
17.1 the order win7 home premium changed into workstation when it arrived home. :(
well, have to pay attentions that the WORKSTATION has two interface available on the NetworkCard that one to Internet and another to
OS. How it can be set to , route to then, it will all depend on the capability inter_against_act among the Hardware, Software and Firewall
etc. so on .
18) ISP adequately protracting your account, example, all register info correct, firewall right configuration time by time?
19) Microsoft alert anything when you re_active own PC license ?
20)
All you pointing out Services and Applications on the Media related no found . Might be hidden?
The problem "Multiple Network" is an Intrusion NetworkCard imposing
illegally using my account. A 30M_WIRE_24m+1m e-agreement.
Then, the imposter built a wireless network before I could connect to the ISP server.
This made me only can get a Wireless address shown by the IPV6 FE80::
which implying a wireless service working on.
DNS auto jump to >172.x.x.x private 218.x.x.x while disabled the directly connection to ISP DHCP server.
Suffix @netvigator.com appending configuration not available. Obviously my PC has been routed to one Private
Route/Switch device, the Unknown shown in Mapping Network for over four months.
NOW THE UNKNOWN DEVICE DO ANYTHING WHAT THEY WANT WHENEVER SECOND.
ISP has no effective and efficiency reaction for it . Since when the e-Contract started , it has plotted to fool the client by
created two unclear e-contracts, Effective Date jump to Before the Modern Agency arrive to my home, on the just agreeable website.
Local @ofca.gov.hk of communication department retain along with ISP company 2 months.
WHO , WHERE BEST FOR A CLIENT TO GET HELP FOR THIS PLEASE?
21) others at later time...
Blue Oisou
Julie L. HUANG -
Changing access specifier from public to private has no effect at runtime
The scenario is like this.
I have two classes A and B and from B i am calling some public methods on A. Until now everything is okay. Now i am changing the access from public to private for the methods in A and recompile it (i'm compiling only A).
The point is, I am not making any change to B, which is still referring to the methods in A, whic are now private .
What will happen if now i try to invoke the above methods on A through B ?? Class A should not allow that, since it is private now. But I am able to access those methods from B!!!
Any idea why it is occurring?????
Now if I try to compile B(note that i didn't compile it earlier along with A), it will throw a error saying that B is trying to access methods which have private access in A, which is right...Nowadays (April 2004) this is still the case, I ran into this behavior today and had a long discussion on it on some java irc channel, but nobody really seemed to know what is exactly going on.
My questions: This access-checking seems to occur only at compile time. Is there a document or whatever notice from sun describing this? Is performance the only reason to do such a thing? -
PRIF-33 and CRS-02307 while changing public network interface, RAC
Hi,
I'm working on an Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production With the Partitioning, Real Application Clusters, Automatic Storage Management. It's a 3 nodes RAC: mgvdb01/02/03
After the installation I had to change IP (different IP and Subnet) to the RAC:
From 172.17.1.0/24 to 10.19.201.0/24.
Node from 172.17.1.31/32/33 to 10.19.201.31/32/33.
The same for VIP(s): from 172.17.1.131/132/133 to 10.19.201.131/132/133.
The oifcfg iflist shows correct ips configuration:
[oracle@mgvdb01 bin]$ ./oifcfg iflist -p -n
eth0 10.19.201.0 PRIVATE 255.255.255.0
eth1 172.17.100.0 PRIVATE 255.255.255.0
I'm following doc 276434.1 from Metalink: How to Modify Public Network Information including VIP in Oracle Clusterware, starting from Case III "Changing public network interface, subnet or netmask".
But at the first operation I've a problem:
[oracle@mgvdb01 bin]$ ./oifcfg getif
eth0 172.17.1.0 global public **THIS HAS TO BE CHANGED**
eth1 172.17.100.0 global cluster_interconnect
[oracle@mgvdb01 bin]# ./oifcfg delif -global eth0/172.17.1.0
PRIF-33: Failed to set or delete interface because hosts could not be discovered
CRS-02307: No GPnP services on requested remote hosts.
PRIF-32: Error in checking for profile availability for host mgvdb02
CRS-02306: GPnP service on host "mgvdb02" not found.
PRIF-32: Error in checking for profile availability for host mgvdb03
CRS-02306: GPnP service on host "mgvdb03" not found.
[oracle@mgvdb01 bin]$ ./oifcfg delif -node mgvdb01 eth0/172.17.1.0
[oracle@mgvdb01 bin]$ ./oifcfg setif -node mgvdb01 eth0/10.19.201.0:public
PRIF-33: Failed to set or delete interface because hosts could not be discovered
CRS-02307: No GPnP services on requested remote hosts.
PRIF-32: Error in checking for profile availability for host mgvdb02
CRS-02306: GPnP service on host "mgvdb02" not found.
PRIF-32: Error in checking for profile availability for host mgvdb03
CRS-02306: GPnP service on host "mgvdb03" not found.Then I restart Clusterware service, but issuing
[oracle@mgvdb01 bin]$ ./oifcfg getif
eth0 172.17.1.0 global public
eth1 172.17.100.0 global cluster_interconnectnothing seems to be changed.
This is blocking following operations, the ones in Case IV.
Do you have any suggestion?
Thanks in advance,
SamuelHi,
I'm working on an Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production With the Partitioning, Real Application Clusters, Automatic Storage Management. It's a 3 nodes RAC: mgvdb01/02/03
After the installation I had to change IP (different IP and Subnet) to the RAC:
From 172.17.1.0/24 to 10.19.201.0/24.
Node from 172.17.1.31/32/33 to 10.19.201.31/32/33.
The same for VIP(s): from 172.17.1.131/132/133 to 10.19.201.131/132/133.
The oifcfg iflist shows correct ips configuration:
[oracle@mgvdb01 bin]$ ./oifcfg iflist -p -n
eth0 10.19.201.0 PRIVATE 255.255.255.0
eth1 172.17.100.0 PRIVATE 255.255.255.0
I'm following doc 276434.1 from Metalink: How to Modify Public Network Information including VIP in Oracle Clusterware, starting from Case III "Changing public network interface, subnet or netmask".
But at the first operation I've a problem:
[oracle@mgvdb01 bin]$ ./oifcfg getif
eth0 172.17.1.0 global public **THIS HAS TO BE CHANGED**
eth1 172.17.100.0 global cluster_interconnect
[oracle@mgvdb01 bin]# ./oifcfg delif -global eth0/172.17.1.0
PRIF-33: Failed to set or delete interface because hosts could not be discovered
CRS-02307: No GPnP services on requested remote hosts.
PRIF-32: Error in checking for profile availability for host mgvdb02
CRS-02306: GPnP service on host "mgvdb02" not found.
PRIF-32: Error in checking for profile availability for host mgvdb03
CRS-02306: GPnP service on host "mgvdb03" not found.
[oracle@mgvdb01 bin]$ ./oifcfg delif -node mgvdb01 eth0/172.17.1.0
[oracle@mgvdb01 bin]$ ./oifcfg setif -node mgvdb01 eth0/10.19.201.0:public
PRIF-33: Failed to set or delete interface because hosts could not be discovered
CRS-02307: No GPnP services on requested remote hosts.
PRIF-32: Error in checking for profile availability for host mgvdb02
CRS-02306: GPnP service on host "mgvdb02" not found.
PRIF-32: Error in checking for profile availability for host mgvdb03
CRS-02306: GPnP service on host "mgvdb03" not found.Then I restart Clusterware service, but issuing
[oracle@mgvdb01 bin]$ ./oifcfg getif
eth0 172.17.1.0 global public
eth1 172.17.100.0 global cluster_interconnectnothing seems to be changed.
This is blocking following operations, the ones in Case IV.
Do you have any suggestion?
Thanks in advance,
Samuel -
VPN Connection Seen As Public Network In Windows 8.1 & No Way To Change It?
Hello,
I have a perfectly working VPN setup in Windows 7 however since I have got a Windows 8 computer and subsequently upgraded it to 8.1 when I connect to the VPN it assigns the connection as Public and I cannot view any of the network shares.
As I understand it, in Windows 8 you could go into the network section of Change PC Settings, right click over the VPN and enable sharing which would convert the public network type to private however there is no longer this option to enable sharing in 8.1
So I'm left with having to disable the public firewall and then connect to the VPN where it works perfectly but is a bit of a pain.
I'm hoping someone can help me to change the network type of the VPN connection from Public to Private, unfortunately the laptop runs Windows 8.1 Home Premium so I do not have access to gpedit.msc
Hope someone can help.
Regards,
MikeHi Mike,
Based on my knowledge, we can use the following method to change the network type of connection from Public to Private.
Set Network to be Private in Windows 8 and 8.1 in Registry
1.Press Win + R keys to open the Run dialog, type regedit, and press Enter.
2.In Registry Editor, navigate to the location below:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\NetworkList\Profiles
3.Expand Profiles, click on each long GUID number subkey, and look at its PofileName string value in the right pane to see if it has the current network name (ex: Network) until found.
4.When you find the correct PofileName for your network name, double click/tap on the Category DWORD value in the same right pane to modify it.
5.Type in a new Data value number for the network location you want, and click/tap on OK.
Network location Data value
Public 0
Private 1
Domain 2
6.When finished, please reboot your computer.
Hope this helps.
Regards,
Kelvin hsu
TechNet Community Support -
MSTDC Error in clustered Environment in while interacting to DB Server from BizTalk server
Hi All,
After completing all my required Biz-talk Integrations (All were related to WCF-Custom Adapter : SQL Binding), I deployed the same to the client environment. But, the same thing which worked for me in my development environment was giving some issues in
the deployed environment.
The main difference was, at client environment - The DB Server was clustered environment and the interaction was through the load balancer.
The first issue I encountered was, there was firewall blocking the access to the DB server from Biz Talk server. Then after enabling and opening the Port 1433, the issue got fixed and I was able to communicate with the DB Server.
After this, I was getting the error related to MSTDC. For this to work properly, in my BizTalk application Configuration, if i set the property for "UseAmbientTransaction" as false under "SqlBinding" for the WCF-Custom Send Port, it is
working as expected!
But, I heard from our Architects that the best approach is to set the property as "TRUE" for "UseAmbientTransaction" property.
So I set the property as true and done the below configurations.
1. Enabling Network DTC using "dcomcnfg.exe"
2. Adding and enabling Fire wall exception for DTC.
Even after making the above changes, I was getting the same error. Then after cross checking with DTCPing and DCTester on both local and deployed copy, i got the below difference.
1. Port 135 (RPC EPM) was opened in my local environment but it was having "Filtered" access at the deployed copy.
So my question is, after opening the above port, will it solve the issue?
Secondly, is there any security threat ter opening the above Port?
Any quick suggestion/solution is highly appreciated.
Thanks in Advance,
AnandHi Anand,
Performing operations on SQL Server using BizTalk Server always involves two resources—the adapter connecting to SQL Server and the BizTalk Message Box residing on SQL Server. Hence, all operations performed using BizTalk Server are performed within the
scope of an MSDTC transaction. So, to use the SQL adapter with BizTalk Server, you must always enable MSDTC. To enable the adapter to perform operations within the scope of an MSDTC transaction, you must configure MSDTC both on the computer running the SQL
adapter and SQL Server. Also, you must add MSDTC to the exceptions list of Windows Firewall. That is the reason why recommend setting for this binding property is
true; otherwise you might either experience message loss or duplicate messages, depending on whether you are performing inbound or outbound operations.
Exception is for operations where the adapter client does not write any data to the SQL Server database, such as a Select operation, you might not want the additional overhead of performing the operations inside a transaction. In such cases,
you can configure the SQL adapter to perform operations without a transactional context by setting the
UseAmbientTransaction binding property to false.
Just refer the link fo all the details:
Configure MSDTC on SQL Server and Adapter Client
Rachit
Rachit
Please mark as answer or vote as helpful if my reply does -
Interconnect is using Public network picking from OSD
Hi All,
In my RAC setup the private interconnect is using public network, it is picking this from Operating system dependent software.
Node1
SQL> desc v$cluster_interconnects;
Name Null? Type
NAME VARCHAR2(15)
IP_ADDRESS VARCHAR2(16)
IS_PUBLIC VARCHAR2(3)
SOURCE VARCHAR2(31)
SQL> select *from v$cluster_interconnects;
NAME IP_ADDRESS IS_ SOURCE
interface 192.168.1.1 NO Oracle Cluster Repository
SQL> SELECT * FROM V$CONFIGURED_INTERCONNECTS;
NAME IP_ADDRESS IS_ SOURCE
INTERCONNECT 192.168.1.1 NO Oracle Cluster Repository
PUBLIC 10.7.200.57 YES Oracle Cluster Repository
SQL>
SQL>
SQL> select *from x$ksxpia;
ADDR INDX INST_ID PUB_KSXPIA
PICKED_KSXPIA NAME_KSXPIA IP_KSXPIA
000000002417AB30 0 1 N
OCR INTERCONNECT 192.168.1.1
000000002417AB30 1 1 Y
OCR
Node2
SQL> select *from v$cluster_interconnects;
NAME IP_ADDRESS IS_ SOURCE
hostname 10.7.200.56 NO OS dependent software
SQL> SELECT * FROM V$CONFIGURED_INTERCONNECTS;
NAME IP_ADDRESS IS_ SOURCE
INTERCONNECT 192.168.1.2 NO Oracle Cluster Repository
hostname 10.7.200.56 OS dependent software
PUBLIC 10.7.200.58 YES Oracle Cluster Repository
SQL> select *from x$ksxpia;
ADDR INDX INST_ID PUB_KSXPIA
PICKED_KSXPIA NAME_KSXPIA IP_KSXPIA
0000000026279B00 0 2 N
OCR INTERCONNECT 192.168.1.2
*0000000026279B00 1 2*
OSD hostname 10.7.200.56
0000000026279B00 2 2 Y
OCR PUBLIC 10.7.200.58
Please check the node 2, it is using the public n/w for the interconnect picked from OSD.
I think, actually it should use the private n/w show pick from OCR.
Please let me know how to make the second node to use the interconnect from private network and should pick from OCR.
Thanks,
MahipalSet the cluster_interconnect parameter in DB or ideally, add this to OCR. But question is , even OSD should give you correct value? Did you find as why is it not coming?
-
I've reset my network settings. I've cleared cache and cookies in the browser. Before yesterday the login screen would appear anytime I attempted to use an app or program that required internet access. Pretty much every program. Now I have a brick tablet at work. I've reset everything I can find. I'm at a dead end.
I've seen other ipads that had the auto login togle and auto join togle under network selection, my ipad does not have those options. Logging in at home is working fine on my private network. This public network is not being reset or forgotten when I choose "forget network" or Safari is blocking the login page and I don't know how to un block it.Well, when I join a public wifi, a log in page displays a few seconds later, displaying the user agreement. But, earlier today, I was trying to connect my friend's 3GS to a public wifi, and it did not show up. So. I don't really know what happen. I think you should toggle the auto Join to on.
-
Weird: Backup file works fine from the network but not when moved into sandbox environment
We have a valid full backup of a database. We know it is valid, we have restored it twice from the network with no problems, but we do not have access to the network location from our sandbox environment.
The .bak file is sizable at about 9GB. The .bak file resides on our internal network, in a SAN drive. No problems there. When we copy the file from there into a sandbox environment to attempt the restore in the sandbox environment it gets corrupted. We've
tried three different times and all three different times it gets corrupted. First time we copied the file over to the sandbox the restore went up to 50% and failed. The second time we copied the file again and attempted the restore again it failed at 70%.
The third time it failed at 60%. The error message we get during the restore is "...Read on ... failed: 13(The data is invalid) Msg 3013, Level 16, State 1, Line 1 Restore database is terminating abnormally."
Now some background here. To move the file our network team is doing this: they have this .vmdk file that they mount out in our production environment (which has access to the network location where the .bak file is), copy the file into the drive, then move
the .vmdk file into the sandbox environment(which does not have access to the network location), mount the drive in the sandbox environment, and then I have access to the .bak file from within the sandbox environment.
Something in the process of using the .vmdk file to move the .bak file from production into the sandbox is causing the file to get corrupted.
Any thoughts? Has anyone seen this before? Any idea? TIA,
Raphael
rferreiraOriginal server that generated the .bak file:
Microsoft SQL Server 2008 R2 (SP1) - 10.50.2550.0 (X64)
Jun 11 2012 16:41:53
Copyright (c) Microsoft Corporation
Enterprise Edition (64-bit) on Windows NT 6.1 <X64> (Build 7601: Service Pack 1) (Hypervisor)
Server where I CAN restore the .bak file from the network location (not inside the sandbox):
Microsoft SQL Server 2012 (SP1) - 11.0.3128.0 (X64)
Dec 28 2012 20:23:12
Copyright (c) Microsoft Corporation
Enterprise Edition (64-bit) on Windows NT 6.1 <X64> (Build 7601: Service Pack 1) (Hypervisor)
Server inside the sandbox where I get the error when attempting to restore the backup:
Microsoft SQL Server 2008 R2 (SP1) - 10.50.2550.0 (X64) Jun 11 2012 16:41:53 Copyright (c) Microsoft Corporation Enterprise Edition (64-bit) on Windows NT 6.1 <X64> (Build 7601: Service Pack 1) (Hypervisor)
rferreira -
How to port database changes from development to a production environment
How do I port database changes from the development to the production environment?
I am using v8 and have always had to redo everything using the schema manager all over in the production environment. Is there an easy way to generate a script, for example to dump the database changes on the development machine to be executed later on the production machine?This should already be a clearly defined change control process. Once a procedure, function, package, trigger, or whatever completes the testing rounds, it should be promoted to production.
Forgive me if it seems I'm trivializing, but I don't see the problem, just copy the object(s) from your software library (or development) into production using whatever tool works best or has been chosen. If you are doing data copies then you have various options again including good old export/import. -
Steps to reproduce bug:
1. edit .pdf file from MS network (i.e a share).
1.1 Browsing the network.
1.2 Once that the file is found.
1.3 Select the file, right click and select edit with Adobe Acrobat".
2. save changes.
Results:
I get message box "document could not save because write access was not granted. only read"
Expected results: I have to save the file because the user has all rights file’s security.
Can you help me ?
Thanks in advance
EnricoFirst, you should ask in Acrobat
The Cloud forum is not about using individual programs
The Cloud forum is about the Cloud as a delivery & install process
If you will start at the Forums Index https://forums.adobe.com/welcome
You will be able to select a forum for the specific Adobe product(s) you use
Click the "down arrow" symbol on the right (where it says All communities) to open the drop down list and scroll
Second, different program, but what helps with SOME permission errors is in the link below
Run as Administrator http://forums.adobe.com/thread/969395 (Encore + "All" Premiere)
Maybe you are looking for
-
I have apple iPhone 4S upgraded to iOS 6.0.1 and everything was working fine suddenly my Wifi was not connecting and found the wifi on/off button is greyed out and to enable it I tried all resets but still my problem have not solved, still wifi is of
-
Need info on Accessing portal services within a Web Dynpro application
Hi, I need information on Accessing portal services within a Web Dynpro application.I want to explore this topic.Can anyone give useful links? Thanks in advance. Rajani N
-
Activities missing in worklist in web time sheet (ESS)
We have a problem concerning activity elements which are present in the worklist in CAT2, but are partially missing in the worklist in the web time sheet. We are using SAP enhancements CATS0001, CATS0009 og CATS0010. I have looked into the project st
-
I've been trying to send a QT movie as an email attachment but when I attach, it shows as a tiny thumbnail. The audio is o.k though.... I posted this before and got a pretty logical response in regard to settings in the inspector, etc... But my sett
-
RE: (forte-users) Check this ( -----THIS MESSAGE WASA VIRUS!!!!!)
The previous message (Check this) is a known virus. (Either that or the sender is emulating it. Either way, do not open the attachment as you will not have "fun" at all. Delete the message immediately. Of course, if I am wrong then I am an idiot! Don