Clustered role 'Availability Role' has exceeded its failover threshold

I am getting this alert on SQL 2012 R2 SP1. So please kindly tell me the solution of the below given alert on windows failover clustering .
Clustered role 'Availability Role' has exceeded its failover threshold. It has exhausted the configured number of failover attempts within the failover period of time allotted to it and will be left in a failed state. No additional attempts will
be made to bring the role online or fail it over to another node in the cluster.Please check the events associated with the failure. After the issues causing the failure are resolved the role can be brought online manually or the cluster may attempt to bring
it online again after the restart delay period.

Hi Syed Tauseef Ahmed,
Please offer more information such as under what circumstances this issue occurs, what event id you have got. The failover threshold is the number of times the group can fail
over within the number of hours specified by the failover period.
The related KB:
Tuning Failover Cluster Network Thresholds
http://blogs.msdn.com/b/clustering/archive/2012/11/21/10370765.aspx
You can refer the following similar thread for the first step troubleshooting:
Clustered role 'Cluster Group' has exceeded its failover threshold.
http://social.technet.microsoft.com/Forums/windowsserver/en-US/4eb44f05-eb9b-448a-821b-359879141608/clustered-role-cluster-group-has-exceeded-its-failover-threshold
I’m glad to be help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Similar Messages

  • Clustered role 'Cluster Group' has exceeded its failover threshold.

    Hello.
    I’m hoping to get some help with a cluster issue I’m having using Windows Storage Server 2012.
    When the cluster is created my Cluster Core Resources are all happy and online.
    I can more the Cluster Name using “move Core Cluster Resources” between the two nodes without any problems.
    If I select ‘Simulate Failure’ on the IP Address resource, it works the first time
    If I do it again shortly after it fails and I get an Event ID 1254, 1205 and 1069.
    Event ID 1254
    Clustered role 'Cluster Group' has exceeded its failover threshold. 
    It has exhausted the configured number of failover attempts within the failover period of time allotted to it and will be left in a failed state. 
    No additional attempts will be made to bring the role online or fail it over to another node in the cluster. 
    Please check the events associated with the failure.  After the issues causing the failure are resolved the role can be brought online manually or the cluster may attempt to bring it online again after the restart delay period.
    Event ID 1205
    The Cluster service failed to bring clustered service or application 'Cluster Group' completely online or offline. One or more resources may be in a failed state. This may impact the availability of the clustered service or application.
    Event ID 1069
    Cluster resource 'Cluster IP Address' of type 'IP Address' in clustered role 'Cluster Group' failed.
    Based on the failure policies for the resource and role, the cluster service may try to bring the resource online on this node or move the group to another node of the cluster and then restart it. 
    Check the resource and group state using Failover Cluster Manager or the Get-ClusterResource Windows PowerShell cmdlet.
    Basically I’m trying to simulate a network failure to make sure the failover kicks in.
    If I click on it and ‘Bring Online’ it comes up fine.
    Where do I find this Threshold Policy and set it to initiate failover if the IP Address resources fails?
    Thank you in advance for your help.

    Hi,
    The failover threshold is the number of times the group can fail over within the number of hours specified by the failover period. For example, if a group failover threshold is set to "5" and its failover period to "3," the clustering software stops attempting
    to bring the group online and leaves the resources within the group in their current state. For example, if the IP Address resource is brought online but the Network Name resource fails, the group is left offline, but the IP Address resource is left online.
    To configure thresholds for a resource:
    Right-click the cluster resource and then select 'Propereties'
    Click 'Advanced'
    Select 'Do not restart' if the cluster service should not attempt to restart. Restart is the default
    If 'Restart' is selected:
    Affect the Group: uncheck to prevent a failure of the selected resource from causing the Server group to failover
    Threshold: number of times the cluster service will attempt to restart the resource, and period is the amount of time in seconds between retries
    Do not modify the 'LooksAlive' and 'IsAlive' settings
    Unless necessary, do not alter the 'Pending Timeout'. This is the amount of time the resource is either in the online or pending or offline pending states before the the cluster service puts it in either offline or failed state
    For more information please refer to following MS articles:
    Windows Failover Clustering Overview
    http://blogs.technet.com/b/rob/archive/2008/05/07/failover-clustering.aspx
    Tuning Failover Cluster Network Thresholds
    http://blogs.msdn.com/b/clustering/archive/2012/11/21/10370765.aspx
    Failover cluster (group) maximum failures limit
    http://blogs.msdn.com/b/arvindsh/archive/2012/03/09/failover-cluster-group-maximum-failures-limit.aspx
    Lawrence
    TechNet Community Support

  • Help!-wont charge- A USB driver has exceeded its power limits?!!?

    my iPhone charged just fine for the past two months, and now it only charges sometimes.
    I will plug it into the wall charger, and it will charge just fine, and then i'll go to charge it again sometime, and it just wont charge, so i tried to plug it into my macbook, and my imac, and they both said "a USB driver has exceeded its power limits, etc, etc." and so i tried my PC, and it gave me the same message. This has happened more than once, and eventually it just charges, but then the whole situation will repeat days later.
    I've called apple over 3 times, and no one has helped me. so...
    help??

    First, try a different cable. It may be shorting out causing the USB port to overload. Especially since it happens on two computers.
    If the cable is ok, try turning the iPhone off. This can be done by holding down the sleep and home buttons until the off slider appears. Then restart it.
    If this doesn't help, take it to an Apple store for assistance.

  • MB.P1.V_CORE has exceeded low warning threshold.

    Please login:
    Serial line login timeout, returns to console stream.
    Enter #. to return to ALOM.
    SC Alert: VOLTAGE_SENSOR @ MB.P0.V_CORE has exceeded low warning threshold.
    I forget the password, and I have already reset the battery, but I can't access the ok prompt.
    Please help.
    Thanks
    Andry

    Contact Sun, and open a service case.
    http://www.sun.com/secure/contact/
    You have a hardware problem.
    You have little or no voltage to your cpu modules (MB.P0 and MB.P1),
    which could be power supply(s), or the PSU backplane, or the systemboard.
    This has nothing to do with forgetting a password.
    If you have service contract coverage, they'll just take care of you.
    If there's no warranty or service contract, then expect to be charged for service.
    An online user-to-user discussion forum cannot help that computer system.
    Edit:
    I take back some of this response.
    If you're simply unable to power up the system,
    then you may need to go back and consult your records for whatever the password might be.
    Download the documentation for your model computer
    and refresh your memory on the ALOM commands,
    such as for how to power-on the chassis.
    http://sunsolve.sun.com/handbook_pub
    Message was edited by:
    rukbat

  • Ran system restore and now my Adobe Acrobat license has exceeded its limit

    I tried restoring computer due to a corrupt install and it removed Adobe Acrobat, since the system restore did not work, I re-installed the OS, patched and then installed Adobe Acrobat XI Professional, entered my license and it comes up with exceeded amounts of use for this license. Would just like to get the license reactivated. Any help would be appreciated. I tried calling in and Adobe is closed on the weekends, tried chat but nobody has come online in quite sometime so now trying the forums since they are 24/7.
    Thank you -
    Jake

    You will need to talk to Adobe, not users on the forums, because only Adobe can reactivate something on their end.   I would imagine that staffing levels increase during the work week.

  • Says my email has exceeded its limit, but I haven't sent out 500 emails in one day. I only sent out 4 groups of about 20.

    Keeps bouncing my emails out of outlook and when I use firefox directly out of gmail, it says I have exceeded my limit of 500 per day. Which I have not sent out that many today.

    That's actually a message from Google, not Firefox. Doing a search for "500 emails exceeded limit" brings up http://www.google.com/support/forum/p/gmail/thread?tid=1c5a1c902b7037e9&hl=en which suggests that your account may have been compromised.
    You need to talk to Google about it. Good luck!

  • Sun fire T1000 - VOLTAGE_SENSOR at MB/V_+3V3STBY has exceeded low warning t

    Hi everyone,
    I am newbie in Sun server and Solaris OS and I have trouble with our old T1000 server. When I power on server, I get message from ALOM console: SC Alert: VOLTAGE_SENSOR at MB/V_+3V3STBY has exceeded low soft shutdown threshold. I read this topic: Re: Error: VOLTAGE_SENSOR at MB/V_+3V3STBY has exceeded low warning threshold and I want to get my serial number of power supply to determine if this alert is factory fault. Can I get it with some command? I can't remove cover from server. Is this alert critical?
    Also I have else one problem with T1000 if i want to start Solaris OS, "booting" stuck in loop:
    Loading the runtime image...
    ALOM - POST run incomplete previously, no POST this time
    ALOM BOOTMON v1.1.1
    ALOM Build Release: 001
    Reset register: e0000000 EHRS ESRS LLRS
    Check for Handshake
    Returned from Boot Monitor and Handshake
    About this problem I read this topic Re: V240 Hangs at loading runtime image but without solution. It should be something together with problem of voltage_sensor?
    Can somebody help me please? I don't know which problem I focus on, I need boot into Solaris.
    Thank you for reply.

    879613 wrote:
    Hi everyone,
    I am newbie in Sun server and Solaris OS and I have trouble with our old T1000 server. When I power on server, I get message from ALOM console: SC Alert: VOLTAGE_SENSOR at MB/V_+3V3STBY has exceeded low soft shutdown threshold. I read this topic: Re: Error: VOLTAGE_SENSOR at MB/V_+3V3STBY has exceeded low warning threshold and I want to get my serial number of power supply to determine if this alert is factory fault. Can I get it with some command? I can't remove cover from server. Is this alert critical?
    Also I have else one problem with T1000 if i want to start Solaris OS, "booting" stuck in loop:
    Loading the runtime image...
    ALOM - POST run incomplete previously, no POST this time
    ALOM BOOTMON v1.1.1
    ALOM Build Release: 001
    Reset register: e0000000 EHRS ESRS LLRS
    Check for Handshake
    Returned from Boot Monitor and Handshake
    About this problem I read this topic Re: V240 Hangs at loading runtime image but without solution. It should be something together with problem of voltage_sensor?
    Can somebody help me please? I don't know which problem I focus on, I need boot into Solaris.
    Thank you for reply.As described in Re: Error: VOLTAGE_SENSOR at MB/V_+3V3STBY has exceeded low warning threshold:
    ... your power supply has failed. You need to replace it.
    Since all T1000's are EOL, you will need to buy a new one unless you have a service contract that covers repair support on the entire chassis.
    No, you cannot type a command to get serial numbers or part numbers of the power supply. Power supplies for such a system are "too stupid" to be able to answer a software inquiry probe. The PSU design is simple. It will work or it will not work.
    If you think there is some sort of a recall on those power supplies, you will need to contact Technical Support directly. These forums are NOT Tech Support.
    Opinion? There is no such recall, or if there ever was the time has long ago expired when someone could take advantage of it.
    Your system doesn't boot because the PSU has failed. Gert the computer repaired. Go to eBay if you must, but you will need to buy replacement parts.

  • Are Pre-defined roles available for Customizing Synchronization?

    Hello Guys,
    In the SAP Help for Solution Manager: <<http://help.sap.com/saphelp_sm40/helpdata/en/48/647e3ddf01910fe10000000a114084/content.htm>>
    it's mentioned that certain authorizations needs to be given for the involved people (admin & customizer), in both the SOLMAN & the component systems.
    Also, its said that the role Application Consultant has all authorizations which are needed to set-up the Customizing Distribution in the SAP Solution Manager system & the authorization profile S_CUS_CMP can be used in the component systems.
    But the AC role "SAP_SOL_AC_COMP" & "S_CUS_CMP" profile donot have all the necessary authorizations specified.
    E.g: Role SAP_SOL_AC_COMP doesnot have project creation authority, whereas S_CUS_CMP has only some authorizations.
    So my question is:
    Along with these two, are there any other roles/profiles which complete the gaps & are readily available for usage ?
    Last option would be to manually create & include the mentioned auth. objects.
    Thanks & Regards
    Chaitu

    Hello Chait,
    Regarding your two questions:
    1) There are seperate roles available for customizing purposes, please check note 803142 <i>Roles for satellite systems</i>. The note administration list an xls with the respective roles for customizing distribution and comparison, namely
    SAP_BC_CUS_ADMIN
    SAP_BC_CUS_CUSTOMIZER
    S_CUS_CMP
    2) What I can recommend is the quick reference for setting up Customizing Distribution which is also part of the help documentation
    http://help.sap.com/saphelp_sm40/helpdata/en/c4/533d4050d89523e10000000a1550b0/content.htm
    Regards,
    Doreen

  • Cluster node has exceeded it's failover threshold

    I am trying to create the Availability group listener for a 2 node cluster and cluster node events show failure due to "Cluster node has exceeded it's failover threshold" after I make one attempt that has failed for a variety of reasons, usually
    permission. How do I set the threshold higher. All the information I get tells me to open processes that are not listed in the failover cluster manager. I haven't seen code that works in powershell. How can I set the failover threshold higher than one?

    Hi,
    Please try to install the recommended hotfixes and updates for Windows Server 2012-based failover cluster then monitor it again.
    The related hotfixes.
    Recommended hotfixes and updates for Windows Server 2012-based failover clusters
    http://support.microsoft.com/kb/2784261/en-us
    Hope this helps.
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Roles missing in available role list at import role option

    We have sap boxi 3.1 and sap integration kit both with SP2.
    we configure sap authentication in the CMC.
    The entitlement system is configured with  a user that has no restriction in sap (SAP ALL user).
    We have approximately 1400 roles in our BW client
    In the available roles list at the import role tab we can see only 220-230 roles.
    The list is randomly.
    When we configure another bw client as a different entitlement system,
    we receive approximately 280 roles out of 1380.
    It looks like we are missing some buffer size configuration.
    Any ideas ??
    thanks.

    Hi Ingo,
    Thanks a lot.
    Yes, the user in the CMC has SAP ALL credential, and is allowed to see all BW roles.
    The missing roles are indeed those that are not assigned to any user.

  • Create Role using SPRO_ADMIN has access to more t-codes then what it shows.

    In SPRO_ADMIN I created a Customizing Project and gave it a scope of:
    - SAP NetWeaver
    - Enterprise Structure
    - Cross-Application Components
    - SAP xApp Resource and Portfolio Management (SAP xRPM)
    - Strategic Enterprise Management/Business Analytics
    - Integration with Other mySAP.com Components
    When I added the customizing authorizations from this project to the role it displayed that 3500 t-codes were added.
    I checked SUIM under "Roles by Role name" and clicked on the Transaction assignment button and 3500 t-codes were displayed.
    I then checked SUIM under "Transactions --> Executable for Roles" and it says there are 95,972!
    How is this possible?
    When I added the role to users they were able to get to t-codes that I couldn't find in the menu.
    I have tried deleting the role and re-adding the customizing auth to a role with a different name.  I have tried deleting the
    customizing project in SPRO_ADMIN and re-creating that then adding it to a different role.  I have tried taking a list of all
    the t-codes that are in this role, creating a new role and adding them through the text file import. All of these examples have
    the same result given above.
    Any ideas on how to create this role so that it only has access to the 3500 t-codes it is supposed to have?
    Thank you in advance for your help!
    Neil

    > There is an entry that has 0 for low and ZZZZZZZZZZZZZZZZZZZZ for high.  How would this have gotten added?  I tried to go into PFCG and remove this line under s_tcode and it will only allow me to view. 
    Then you are experiencing the same as PIQAGR_CUST, but with other consequences and a different source. An S_TCODE, S_RFC and S_SERVICE authorization which is display only is either in the menu or pulled in from SU24.
    To find the offending transaction, go to table USOBT_C field HIGH and search for Z* to find it and remove it from SU24. Also check SU22 to see whether it was added there... There might be more than one and other roles will be impacted when they are opened in expert mode!
    Then go to USOBT_CD and find the change document for that transaction code for field HIGH = ZZZZZZZZ... and the user name and date of the change.
    Find that person, and show them this thread...
    You might want to check all other roles which have this transaction in the menu... as that will probably be the origin of the problem and give you an insight into their frustration (and this "workaround" solution).
    What you are doing is a hard day's work and for SPRO related roles this solution (or manual authorizations and profiles) is not uncommon to observe.
    If the quality of the SU22 data were better then it would be less of a hassle and problem. In SU24 you can tune it and remove such things, but ideally the original system should do this. With each support package SAP improves this data, but there is still a lot of standard junk in there as well.
    Retrofitting security is always the most expensive option....
    Cheers,
    Julius
    Edited by: Julius Bussche on Jan 14, 2010 11:00 PM

  • Production order cost has exceeded the released budget of its WBS

    Dear All,
    I have got a case where the prod. order cost has exceeded the released budget of its concerned WBS.
    I found that the budget check is active and working fine for Prod. order and other activities.
    I am not getting , how this default has occured.
    Please help me resolving this case.
    Regards,
    Vishal

    If the budget check is active against Released budget and Production order assigned to WBS has crossed released budget. It should not happen.
    Please run CJEN and check the report.
    Regards
    Nitin

  • OIM 11g R2 Available Roles For Organizations Is Empty After XML Import

    Hi,
    When we exported Organizations in OIM via Deployment Manager and imported them back, available roles on Organizations are gone.
    To be exact; Hierarchical role assignments are gone, which are done using "include-sub-orgs" check while putting organizations to Roles.
    To understand the problem,
    We took a single organization, exported it, changed only organization name in the XML and imported it back. The results are the same.
    We included every possible dependency in the xml to see if this was the issue, apparently it wasn't.
    Furthermore,
    On the Role screens' Available Organization's tab, when we check the "include sub orgs" box, it works fine on manually added organizations. They are shown on Available Roles for the Organizations.
    But this doesn't work on imported organizations.
    Is there a trick to this in R2?
    How can we export-import the organizations and still see the available roles?
    Thanks,
    Erdogdu

    Hi All
    Any updates please . Can any one just update whether creating a custom attribute on User Profile adds the attribute in the list of attributes for membership rules for roles .
    Thanks
    Darshan

  • USB device has exceeded power limits of its hub AND no sound

    Yesterday no sound, but worse...Trying to connect to computer to charge gives me the message "A USB device has exceeded the power limits of its hub power. Clicking on the balloon states "A USB device has malfunctioned & exceeded the power limits of its hub port. You should disconnect the device." Plugging into the wall charger states "This accessory is not made to work with iPhone...want to change to Airplane mode..." Is my iPhone dead? Ideas please. Thanks

    Hi, Did you every get a reply? I'm having the same issue. The phone was working fine yesterday. Now, the button doesn't work and I can't sync it to restore it because I'm getting the same USB power limit message.

  • Power Surge on Hub Port: A USB Device has exceeded the power limits of its hub port.

    When I attempt to install an external DVD/CDRW I receive the following:
    Power Surge on Hub Port: A USB Device has exceeded the power limits of its hub port.
    I am forced to reset.

    I would guess that your external DVD is drawing too much power from the USB port, and could be one of the older units; newer units are usually more power efficient. Such device usually come with a USB cable with two USB connectors that can draw power from two USB ports simultaneously. You may be able to get such cable separately but since the two USB ports are located at extreme ends in the S10, you may want to check that the cable come with the USB connectors with sufficient length to reach both the USB ports simultaneously.   
    View my Blog on the Lenovo S10

Maybe you are looking for