Cme call drop after 3 min

I have problem in cme9.1 with 8 fxo it was working fine, Before one week incoming call drop after 3 min this is configuration for fxo 
supervisory disconnect dualtone mid-call
no battery-reversal
input gain -3
output attenuation -3
echo-cancel coverage 32
cptone BE
timeouts initial 5
timeouts interdigit 3
timeouts call-disconnect 3
timeouts ringing 5
timeouts wait-release 1
timing hookflash-out 500
timing guard-out 300
timing sup-disconnect 50
connection plar opx xxxx
impedance complex2
caller-id enable
caller-id alerting line-reversal
caller-id alerting dsp-pre-allocate

Hello,
Can you please post the show run and collect the below debug making one test call.
debug voip ccapi inout
debug vpm signal
debug voip vtsp default
debug voip vtsp session
debug voip hpi all
Regards
Nadeem

Similar Messages

  • Why can't I make any calls on facetime, the call drops after saying connecting.

    Why can't I make any calls on facetime, the call drops after saying connecting for a few seconds. I'm using an iphone 5, 32 GB on IOS 6.0.1 over 3G network in Muscat, Oman. Just to be clear, I was able to make facetime call in Muscat about a week ago.

    If this user to user forum could not help you with your issue, contact Apple to get your Device serviced or looked at.
    http://www.apple.com/contact/

  • Calls dropping after almost 2 hours (1:59hr)

    hello everyone!i recently purchased the unlimited europe subscription,the thing is, the call quality is bad, and not only that,the call drops after almost 2 hours of a low quality call,i can deal with the low quality and everything,but why does it have to end the call just like that? i've purchased this service because i trusted it to replace whatsapp voice calls,since my girlfriend's internet at her university is bad, and keeps going on and off.we usually go to sleep together online... when the call is on-going.she likes when i stay with her all night. and her internet started giving us hard times,and i was thinking skype will save my day and night, but... it really wasnt what i expected. i hope that there's a solution for this.im using asus zenfone 5 for the calls now (if it means anything). and for the low quality thing, is there a way to fix this? i tried several devices...its the same in all of them, can hardly hear anything...voip runs smoother, but for that i dont need skype anymore.hoping to get some help! thanks!

    Well since nobody could really help with my situation, figured I'll write down what happened so it may help a few people in need. My restore freeze problem was solved by removing then reinstalling itunes again since I had an older version of itunes and was unable to update without doing so. The "restore from backup" option came back after the factory setting restore and for some reason the whole process only went smoothly when I tried doing it on another computer. Anyhow everything is back to normal now.

  • UC320 - Phone Calls Drop After Transferred

    Good morning all -
    I have my UC320 setup for a small law firm.  I have all calls in normal business hours transfer to an automatic call service (help desk/reception).  Once they receive the call they then forward it to the attorney in which they want to speak to.  Once the call is forwarded, after approximately 9 minutes and 30 seconds the call drops.   Does anyone know what this can be caused by?
    Any and all help is greatly appreciated.

    Hello,
    I personally make calls longer than 60 min, with CCME to some South American friends (trying to keep it vague to not release any personal info :)
    Anyway, if you use ISDN, it is easy to see which side is dropping the call. Enter "debug isdn q931" and "term mon". This is relatively low output and can be left on for days. You can also log to router memory or syslog server.
    If you don't have isdn you can still see many things with "debug vpm signal". It is a little more verbose but still not overwhelming.
    Hope this helps, if so please rate post!

  • Calls dropped after free minutes run out

    Hello,
    There is already a post on this subject, but it's back in 2013, so I figured re-raising it would be worthwhile, particularly given how annoying it is. Here is the original post:
    http://community.skype.com/t5/Rates-and-subscriptions/After-Office-365-Minutes-Run-Out-Call-Drops-Bu...
    Basically, I have some free minutes given to me every month thanks to my subscription with Office 365. When these minutes run out, my call drops - even though I have cash credit on my account. The fact it does not do a seamless transfer from my account of "free minutes" to my account of "cash" is extremely annoying. Given that most of my calls are to companies (e.g. to make payments, transfers, talk with the bank, etc) it is extremely annoying to have to reconnect with the caller, through the machine, give address/card details again, etc... And this is something that happens once every single month!! It's very annoying, and really stupid that Skype won't fix this. It's hardly rocket science to make both accounts refer to a single consolidated account.
    With increasing amounts of competition out there this is a good enough reason to take my business elsewhere. Even if it's slightly more expensive, whilst I can understand that issues sometimes take a while to fix - this seems to me like a deliberate decision not to do anything about a customer complaint, and I can't support such an attitude from a company.
    Skype - please tell me that this will post will change your mind about this issue, and that you will add this to your list of things to fix.
    E

    Miket67m wrote:
    1. It is clear that when a 60 mins subscription comes to and end the call drops rather than the call  continuting and moving to Skpe credit.  It is at best irritating and should be fixable.
    2.  If nothing else it would be helpful to have a warning flag up that the call is about to drop, particular if the call is important.  Sort it out Skype!
    Hello and welcome to the Skype Community.
    1. Unfortunately, calls can't be continued seamlessly when the call charging protocol changes. In this case the change is from Subscription to Credit.
    2. I don't think that's possible but I'll check and advise.
    TIME ZONE - US EASTERN. LOCATION - PHILADELPHIA, PA, USA.
    I recommend that you always run the latest Skype version: Windows & Mac
    If my advice helped to fix your issue please mark it as a solution to help others.
    Please note that I generally don't respond to unsolicited Private Messages. Thank you.

  • Dial tone continues after call is answered then call drops after 1 minutes

    This morning I have had problems with calling skype contacts.  After I initiate the call the person on the other end picks up but the dail tone is still in the background.  After a minute or so the dial tone go to busy and the entire call drops.

    I downloaded new version of Skype and it works. Strange that it didn't auto update since 6.21 even thought auto update was on. Now it is 6.22.

  • Calls dropped after 5:02

    Trying to call landlines with Android phone, but the call repeatedly drops after 5:02 (according to the call log). This happened with the latest Android version, so I tried downgrading but that didn't help.
    The internet connection is stable, i.e. I don't experience any other drop in connectivity, especially every 5 minutes.
    Any thoughts? What can I do to prevent this from happening?
    LG 4X HD
    Android 4.1.2
    Skype 4.9.0.45564
    Thanks!

    Hello and welcome to the Skype Community.
    From your account it appears that a percentage of calls are dropped while others behave normally.
    Checking for you.
    TIME ZONE - US EASTERN. LOCATION - PHILADELPHIA, PA, USA.
    I recommend that you always run the latest Skype version: Windows & Mac
    If my advice helped to fix your issue please mark it as a solution to help others.
    Please note that I generally don't respond to unsolicited Private Messages. Thank you.

  • My BB 8320 camera is not working and calls drop after 8 to 10 minutes...

    Hi,
    Acutally I got this 8320 as a gift 6 months back.  The problem i am facing is that the camera is not starting at all, i have tried troubleshooting it and it is not working still, and sometimes when i am speaking on phone the call drops at the 8th or 10th minute, it doesnt happens every time but does happens very often.. 
    The Version is V4.5.0.201 (platform2.7.0.85)
    Will upgrading the software will work or else can you suggest me an solution, i am in need of a nice helping solution.
    any other information you need just let me know...
    Regards,
    Karan

    I'm not familiar with 4.5.0.201.  Is that what's listed in Options >About on the 3rd line down?  The latest I was aware of was 4.5.0.187.  What carrier is branded on the device?
    What happens when you try to start the camera?  do you get an error message of any k ind?
    1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
    2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

  • WebEx Meeting Server 1.5 - Call drop after entering meeting number and #

    Hi everyone,
    Just installed a new CWMS server version 1.5... all features seem to work EXCEPT when I use the call in function, I type in the meeting number, hit # and the call is terminated.
    I read through this document:
    http://www.cisco.com/c/en/us/td/docs/collaboration/CWMS/b_troubleshootingGuide/b_troubleshootingGuide_chapter_01000.pdf
    From the document:
    Call-In Issues
    • Problem Users hear a reorder tone before or after the complete number is dialed.
    • Problem The "Your call cannot be completed as dialed" message is played by the annunciator.
    • Problem During call-back, a user's call terminates after pressing 1 to join the meeting.
    • Problem During call-in, a user's call terminates after entering the meeting ID followed by #.
    Possible Cause You need to reconfigure your CUCM servers.
    Solution Reconfigure your CUCM settings as follows: Use the "<NONE>" partition and "<NONE>" CSS
    (Calling Search Space) for all Cisco WebEx Meetings Server related entities in CUCM (for example, route
    patterns, SIP route patterns, SIP trunks, etc.).
    Solution Use one partition and one CSS specifically assigned for all Cisco WebEx Meetings Server related
    entities. For more information refer to the system guide for your CUCM version.
    I configured my route pattern to use <NONE> and all other option as <NONE> and still the call is terminated.
    I created a css_webex CSS and put in pt_internal and assigned that and I still get terminated.
    Am I missing something here?

    Personally, I never really use the null partition but before we go there.  You have a couple different route patterns.  The first is an inbound call pattern(s) that are going to be standard route patterns (i.e. numeric) and you'll have some outbound PSTN patterns for the actual outdialing that CWMS does.  You then have some SIP route patterns that can either be defined as IP or FQDN for each media server.  After you connect and then want to join a meeting, those SIP route patterns are used to redirect you to the appropriate server where a meeting is hosted.  For those patterns, are you using IP or FQDN and what partition are they in?  If you are using FQDN then you may need to change to IP depending on your DNS configuration on CUCM.
    Hailey

  • Multiple queues, few people reporting issue, calls drops after short time

    Random agents, usually about 2 or 3 per day for last couple of days, have reported that a call will be delivered to them from the queue and a minute or less into the call the call will just drop.  It's happened on different queues on different call centers coming in on different PRI's, etc.  Can't seem to find anything wrong and it doesn't seem to be widespread at this point.  Just a couple of people a day have complained about it and they come in the next day and it's fine.  Any suggestions?

    Get some ANIs and time stamps, ask your telco to pull some reports on their side.  Look at IGW logs (both Express and Enterprise) and termination detail records (assuming Enterprise).
    david

  • Cisco SX20 Call drops after 15 minutes Please help urgent !!

    Hi All,
    We have Below scenario
    SX20----> MCU<----- Polycom
    SX20 -----> Polycom
    Issue: When we make a Call from SX20 to Polycom IP to IP call or even using MCU Cisco SX20 gets disconnected after fixed interval ( 15 - 20 minutes)
    Calls from Other endpoints ---> Polycom to polycom with MCU and also 1:1 ,1: multiple over MCU works fine.
    Only issue is when Cisco SX20 comes in to the picture.
    Please sugest is it a known issue?
    Or doi we have to update firmware/licenses or any other software in cisco SX20?
    Or is it a bug?
    Or do we need to check on firewall level
    The SX20 has the latest firmware already.
    Please help !!!!!!!!
    Regards,
    Ajith

    As Martin has said above, the 15 minute disconnection issues are usually a network issue.
    Are all your devices on the same LAN, or are they at different locations?  Are you using any call control (VCS/CUCM), or are the devices standalone?  What protocol are you using (H.323/SIP)?
    If you're using NAT, have you got the NAT settings set up correctly on your devices?
    What model device is the Polycom?  Is the software on the Polycom up to date?
    There are many questions which we can ask, but need to understand your environment a little more.
    Wayne
    Please remember to rate responses and to mark your question as answered if appropriate.

  • Why do some home phone connect incoming calls drop after CID announcement?

    I just changed my old house land line service with AT&T over to VZ which carries my cell phone accounts. I have the HPC tied into my Panasonic home system with Voice mail recorder and  with 5 cordless handsets.No problem with calling out and receiving a majority of incoming calls. But callers do have trouble calling in. When we initially pick up the handset to take a call after the Caller ID is announced and say Hello, there is only silence. After a 2 to 4 second pause a busy signal is heard that terminates the call attempt. The missed call number is recorded in the ansering systems list as a missed call so at least we know who tried to call, unless it is announced as private or unknown.Has anyone else experienced this?

    I just changed my old house land line service with AT&T over to VZ which carries my cell phone accounts. I have the HPC tied into my Panasonic home system with Voice mail recorder and  with 5 cordless handsets.No problem with calling out and receiving a majority of incoming calls. But callers do have trouble calling in. When we initially pick up the handset to take a call after the Caller ID is announced and say Hello, there is only silence. After a 2 to 4 second pause a busy signal is heard that terminates the call attempt. The missed call number is recorded in the ansering systems list as a missed call so at least we know who tried to call, unless it is announced as private or unknown.Has anyone else experienced this?

  • Upgraded to 5S calls drop after a minute or so

    All calls to Miami effected - local calls (Orlando) don't seem impacted

    By connecting to ethernet and wifi you're creating a network loop back on itself. I've experienced problems like this in the past ... nothing really to do with Apple TV. Try one or the other, WiFi or Ethernet ... assuming you have a wireless router that's hooked up to you high speed modem.

  • Cisco SX20 Call drop issue after 15 minutes !!!!! urgent help needed !!!

    Hi All,
    We have Below scenario
    SX20----> MCU<----- Polycom
    SX20 -----> Polycom
    Issue: When we make a Call from SX20 to Polycom IP to IP call or even using MCU Cisco SX20 gets disconnected after fixed interval ( 15 - 20 minutes)
    Calls from Other endpoints ---> Polycom to polycom with MCU and also 1:1 ,1: multiple over MCU works fine.
    Only issue is when Cisco SX20 comes in to the picture.
    Please sugest is it a known issue?
    Or doi we have to update firmware/licenses or any other software in cisco SX20?
    Or is it a bug?
    Or do we need to check on firewall level
    The SX20 has the latest firmware already.
    Please help !!!!!!!!
    Regards,
    Ajith

    Please refer to your duplicate thread in the TelePresence section of the forums: https://supportforums.cisco.com/discussion/12383611/cisco-sx20-call-drops-after-15-minutes-please-help-urgent.
    Wayne
    Please remember to rate responses and to mark your question as answered if appropriate.

  • SIP Calls Drop. Receive Bye From Cube 15min,30min, 45min

    Hello,
    Running into an odd issue. I've seen several others having this problem with calls dropping after 15min duration. But this is a bit different. Sometimes long duration calls drop at 15min. Some at 30min, others at 45min. And sometimes not at all. Call flow is such.
    8831-sip--CUCM--sip--Cube--ITSP
    I'm convinced this is likely a problem with the refresh timer. But I can't explain why it wouldn't just fail only at 15min. It's also interesting to note I've only seen this on the 8831. I tried getting the issue with debugs from the cube but of course it didn't happen once I turned on ccsip message.
    From the callmanager traces I see the bye arrive from cube with Reason Q.850 cause=102. 
    The CUCM version is 9.1.2  and cube is 15.2(4)M1. I did see some odd defect in 15.1 related to this where the refresh on the cube would send out 3 invites to the ITSP on an update. I guess it would have only 33% chance of getting it right. Any help someone could provide I'd appreciate it.

    Thanks for the replies.
    So was able to capture it while had debugs running. This time it disconnected after an hour. Same cause=102.
    Now here is where it gets interesting in the debugs. I see an invite is sent 3 seconds from callmanager. I assume this is a refresher with the same call-id. Cube receives it and sends out to ITSP. With a new call-id. We then receive a bye from ITSP cause=86. Which then of course is sent to callmanager. Here are the relevent sections of debugs.
    Received from cucm to cube:
    820421: May  6 09:00:42.976: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    2014-05-06 09:00:43            2365082: Received:
    2014-05-06 09:00:43            2365083: INVITE sip:[email protected]:5060;transport=tcp SIP/2.0
    2014-05-06 09:00:43            2365084: Via: SIP/2.0/TCP 10.38.246.136:5060;branch=z9hG4bK28bab16dbd5664
    2014-05-06 09:00:43            2365085: From: "Marcos Vazquez" <sip:[email protected]>;tag=3831180~dfbf10b3-6c69-4443-852f-cbf609935a6f-35009402
    2014-05-06 09:00:43            2365086: To: <sip:[email protected]>;tag=5EBA2282-19C8
    2014-05-06 09:00:43            2365087: Date: Tue, 06 May 2014 15:00:42 GMT
    2014-05-06 09:00:43            2365088: Call-ID: [email protected]
    2014-05-06 09:00:43            2365089: Supported: 100rel,timer,resource-priority,replaces
    2014-05-06 09:00:43            2365090: Min-SE:  1800
    2014-05-06 09:00:43            2365091: User-Agent: Cisco-CUCM9.1
    2014-05-06 09:00:43            2365092: Allow: INVITE, OPTIONS, I
    2014-05-06 09:00:43            2365093: NFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
    2014-05-06 09:00:43            2365094: CSeq: 106 INVITE
    2014-05-06 09:00:43            2365095: Max-Forwards: 70
    2014-05-06 09:00:43            2365096: Expires: 300
    2014-05-06 09:00:43            2365097: Allow-Events: presence, kpml
    2014-05-06 09:00:43            2365098: Supported: X-cisco-srtp-fallback
    2014-05-06 09:00:43            2365099: Supported: Geolocation
    2014-05-06 09:00:43            2365100: P-Asserted-Identity: "Marcos Vazquez" <sip:[email protected]>
    2014-05-06 09:00:43            2365101: Remote-Party-ID: "Marcos Vazquez" <sip:[email protected]>;party=calling;screen=yes;privacy=off
    2014-05-06 09:00:43            2365102: Contact: <sip:[email protected]:5060;transport=tcp>
    2014-05-06 09:00:43            2365103: Content-Type: application/sdp
    2014-05-06 09:00:43            2365104: Content-Length: 371
    2014-05-06 09:00:43            2365105:
    2014-05-06 09:00:43            2365106: v=0
    2014-05-06 09:00:43            2365107: o=CiscoSystemsCCM-
    2014-05-06 09:00:43            2365108: SIP 3831180 1 IN IP4 10.38.246.136
    2014-05-06 09:00:43            2365109: s=SIP Call
    2014-05-06 09:00:43            2365110: c=IN IP4 10.96.5.28
    2014-05-06 09:00:43            2365111: b=TIAS:64000
    2014-05-06 09:00:43            2365112: b=AS:64
    2014-05-06 09:00:43            2365113: t=0 0
    2014-05-06 09:00:43            2365114: m=audio 31146 RTP/AVP 18 0 116 101
    2014-05-06 09:00:43            2365115: a=rtpmap:0 PCMU/8000
    2014-05-06 09:00:43            2365116: a=ptime:20
    2014-05-06 09:00:43            2365117: a=rtpmap:116 iLBC/8000
    2014-05-06 09:00:43            2365118: a=ptime:20
    2014-05-06 09:00:43            2365119: a=maxptime:60
    2014-05-06 09:00:43            2365120: a=fmtp:116 mode=20
    2014-05-06 09:00:43            2365121: a=rtpmap:18 G729/8000
    2014-05-06 09:00:43            2365122: a=ptime:20
    2014-05-06 09:00:43            2365123: a=fmtp:18 annexb=no
    2014-05-06 09:00:43            2365124: a=rtpmap:101 telephone-event/8000
    2014-05-06 09:00:43            2365125: a=fmtp:101 0-15
    2014-05-06 09:00:43            2365126: 5820422: May  6 09:00:42.978: //3024943/CC044C80000B/SIP/Msg/ccsipDisplayMsg:
    Sent to ITSP:
     Sent: Which looks like 3 are sent.
    2014-05-06 09:00:43            2365128: INVITE sip:12.194.190.26:5060;transport=udp SIP/2.0
    2014-05-06 09:00:43            2365129: Via: SIP/2.0/UDP 12.17.223.243:5060;branch=z9hG4bK2D699C1126
    2014-05-06 09:00:43            2365130: P-Asserted-Identity: "Marcos Vazquez" <sip:[email protected]>
    2014-05-06 09:00:43            2365131: From: "Marcos Vazquez" <sip:[email protected]>;tag=5EBA1628-22FC
    2014-05-06 09:00:43            2365132: To: <sip:[email protected]>;tag=8088820710430052_c2b05.1.1.1385369448756.0_9843675_19511361
    2014-05-06 09:00:43            2365133: Date: Tue, 06 May 2014 15:00:42 GMT
    2014-05-06 09:00:43            2365134: Call-ID: [email protected]
    2014-05-06 09:00:43            2365135: Supported: 100rel,timer,resource-priority,replaces,sdp-an
    2014-05-06 09:00:43            2365136: at
    2014-05-06 09:00:43            2365137: Min-SE:  1800
    2014-05-06 09:00:43            2365138: Cisco-Guid: 3422833792-0000065536-0000746374-2297832970
    2014-05-06 09:00:43            2365139: User-Agent: Cisco-SIPGateway/IOS-15.2.4.M1
    2014-05-06 09:00:43            2365140: Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    2014-05-06 09:00:43            2365141: CSeq: 105 INVITE
    2014-05-06 09:00:43            2365142: Max-Forwards: 70
    2014-05-06 09:00:43            2365143: Timestamp: 1399388442
    2014-05-06 09:00:43            2365144: Contact: <sip:[email protected]:5060>
    2014-05-06 09:00:43            2365145: Expires: 60
    2014-05-06 09:00:43            2365146: Allow-Events: telephone-event
    2014-05-06 09:00:43            2365147: Content-Type: application/sdp
    2014-05-06 09:00:43            2365148: Content-Length: 334
    2014-05-06 09:00:43            2365149:
    2014-05-06 09:00:43            2365150: v=0
    2014-05-06 09:00:43            2365151: o=CiscoSystemsSIP-GW-UserAgent 8182 4488 IN IP4 12.17.223.243
    2014-05-06 09:00:43            2365152: s=SIP Call
    2014-05-06 09:00:43            2365153: c=IN IP4 1
    2014-05-06 09:00:43            2365154: 2.17.223.243
    2014-05-06 09:00:43            2365155: t=0 0
    2014-05-06 09:00:43            2365156: m=audio 18760 RTP/AVP 18 0 100 101
    2014-05-06 09:00:43            2365157: c=IN IP4 12.17.223.243
    2014-05-06 09:00:43            2365158: a=rtpmap:18 G729/8000
    2014-05-06 09:00:43            2365159: a=fmtp:18 annexb=no
    2014-05-06 09:00:43            2365160: a=rtpmap:0 PCMU/8000
    2014-05-06 09:00:43            2365161: a=rtpmap:100 X-NSE/8000
    2014-05-06 09:00:43            2365162: a=fmtp:100 192-194
    2014-05-06 09:00:43            2365163: a=rtpmap:101 telephone-event/8000
    2014-05-06 09:00:43            2365164: a=fmtp:101 0-15
    2014-05-06 09:00:43            2365165: 5820423: May  6 09:00:42.978: //3024942/CC044C80000B/SIP/Msg/ccsipDisplayMsg:
    2014-05-06 09:00:43            2365166: Sent:
    2014-05-06 09:00:43            2365167: SIP/2.0 100 Trying
    2014-05-06 09:00:43            2365168: Via: SIP/2.0/TCP 10.38.246.136:5060;branch=z9hG4bK28bab16dbd5664
    2014-05-06 09:00:43            2365169: From: "Marcos Vazquez" <sip:[email protected]>;tag=3831180~dfbf10b3-6c69-4443-852f-cbf609935a6f-35009402
    2014-05-06 09:00:43            2365170: To: <sip:[email protected]>;tag=5EBA2282-19C8
    2014-05-06 09:00:43            2365171: Date: Tue, 06 May 2014 15:00:42 GMT
    2014-05-06 09:00:43            2365172: Call-ID: [email protected]
    2014-05-06 09:00:43            2365173: CSeq: 106 INVITE
    2014-05-06 09:00:43            2365174: Allow-Events: telephone-event
    2014-05-06 09:00:43            2365175: Server: Cisco-SIPGateway/IOS-15.2.4.M1
    2014-05-06 09:00:43            2365176: Content-Length: 0
    2014-05-06 09:00:43            2365177:
    2014-05-06 09:00:43            2365178: 5820424: May  6 09:00:43.479: //3024943/CC044C80000B/SIP/Msg/ccsipDisplayMsg:
    2014-05-06 09:00:43            2365179: Sent:
    2014-05-06 09:00:43            2365180: INVITE sip:12.194.190.26:5060;transport=udp SIP/2.0
    2014-05-06 09:00:43            2365181: Via: SIP/2.0/UDP 12.17.223.243:5060;branch=z9hG4bK2D699C1126
    2014-05-06 09:00:43            2365182: P-Asserted-Identity: "Marcos Vazquez" <sip:[email protected]>
    2014-05-06 09:00:43            2365183: From: "Marcos Vazquez" <sip:[email protected]>;tag=5EBA1628-22FC
    2014-05-06 09:00:43            2365184: To: <sip:[email protected]>;tag=8088820710430052_c2b05.1.1.1385369448756.0_9843675_19511361
    2014-05-06 09:00:43            2365185: Date: Tue, 06 May 2014 15:00:43 GMT
    2014-05-06 09:00:43            2365186: Call-ID: [email protected]
    2014-05-06 09:00:43            2365187: Supported: 100rel,timer,resource-priority,replaces,sdp-an
    2014-05-06 09:00:43            2365188: at
    2014-05-06 09:00:43            2365189: Min-SE:  1800
    2014-05-06 09:00:43            2365190: Cisco-Guid: 3422833792-0000065536-0000746374-2297832970
    2014-05-06 09:00:43            2365191: User-Agent: Cisco-SIPGateway/IOS-15.2.4.M1
    2014-05-06 09:00:43            2365192: Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    2014-05-06 09:00:43            2365193: CSeq: 105 INVITE
    2014-05-06 09:00:43            2365194: Max-Forwards: 70
    2014-05-06 09:00:43            2365195: Timestamp: 1399388443
    2014-05-06 09:00:43            2365196: Contact: <sip:[email protected]:5060>
    2014-05-06 09:00:43            2365197: Expires: 60
    2014-05-06 09:00:43            2365198: Allow-Events: telephone-event
    2014-05-06 09:00:43            2365199: Content-Type: application/sdp
    2014-05-06 09:00:43            2365200: Content-Length: 334
    2014-05-06 09:00:43            2365201:
    2014-05-06 09:00:43            2365202: v=0
    2014-05-06 09:00:43            2365203: o=CiscoSystemsSIP-GW-UserAgent 8182 4488 IN IP4 12.17.223.243
    2014-05-06 09:00:43            2365204: s=SIP Call
    2014-05-06 09:00:43            2365205: c=IN IP4 1
    2014-05-06 09:00:44            2365206: 2.17.223.243
    2014-05-06 09:00:44            2365207: t=0 0
    2014-05-06 09:00:44            2365208: m=audio 18760 RTP/AVP 18 0 100 101
    2014-05-06 09:00:44            2365209: c=IN IP4 12.17.223.243
    2014-05-06 09:00:44            2365210: a=rtpmap:18 G729/8000
    2014-05-06 09:00:44            2365211: a=fmtp:18 annexb=no
    2014-05-06 09:00:44            2365212: a=rtpmap:0 PCMU/8000
    2014-05-06 09:00:44            2365213: a=rtpmap:100 X-NSE/8000
    2014-05-06 09:00:44            2365214: a=fmtp:100 192-194
    2014-05-06 09:00:44            2365215: a=rtpmap:101 telephone-event/8000
    2014-05-06 09:00:44            2365216: a=fmtp:101 0-15
    2014-05-06 09:00:44            2365217: 5820425: May  6 09:00:44.479: //3024943/CC044C80000B/SIP/Msg/ccsipDisplayMsg:
    2014-05-06 09:00:44            2365218: Sent:
    2014-05-06 09:00:44            2365219: INVITE sip:12.194.190.26:5060;transport=udp SIP/2.0
    2014-05-06 09:00:44            2365220: Via: SIP/2.0/UDP 12.17.223.243:5060;branch=z9hG4bK2D699C1126
    2014-05-06 09:00:44            2365221: P-Asserted-Identity: "Marcos Vazquez" <sip:[email protected]>
    2014-05-06 09:00:44            2365222: From: "Marcos Vazquez" <sip:[email protected]>;tag=5EBA1628-22FC
    2014-05-06 09:00:44            2365223: To: <sip:[email protected]>;tag=8088820710430052_c2b05.1.1.1385369448756.0_9843675_19511361
    2014-05-06 09:00:44            2365224: Date: Tue, 06 May 2014 15:00:44 GMT
    2014-05-06 09:00:44            2365225: Call-ID: [email protected]
    2014-05-06 09:00:44            2365226: Supported: 100rel,timer,resource-priority,replaces,sdp-an
    2014-05-06 09:00:44            2365227: at
    2014-05-06 09:00:44            2365228: Min-SE:  1800
    2014-05-06 09:00:44            2365229: Cisco-Guid: 3422833792-0000065536-0000746374-2297832970
    2014-05-06 09:00:44            2365230: User-Agent: Cisco-SIPGateway/IOS-15.2.4.M1
    2014-05-06 09:00:44            2365231: Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
    2014-05-06 09:00:44            2365232: CSeq: 105 INVITE
    2014-05-06 09:00:44            2365233: Max-Forwards: 70
    2014-05-06 09:00:44            2365234: Timestamp: 1399388444
    2014-05-06 09:00:44            2365235: Contact: <sip:[email protected]:5060>
    2014-05-06 09:00:44            2365236: Expires: 60
    2014-05-06 09:00:44            2365237: Allow-Events: telephone-event
    2014-05-06 09:00:44            2365238: Content-Type: application/sdp
    2014-05-06 09:00:44            2365239: Content-Length: 334
    2014-05-06 09:00:44            2365240:
    2014-05-06 09:00:44            2365241: v=0
    2014-05-06 09:00:44            2365242: o=CiscoSystemsSIP-GW-UserAgent 8182 4488 IN IP4 12.17.223.243
    2014-05-06 09:00:44            2365243: s=SIP Call
    2014-05-06 09:00:44            2365244: c=IN IP4 1
    2014-05-06 09:00:44            2365245: 2.17.223.243
    2014-05-06 09:00:44            2365246: t=0 0
    2014-05-06 09:00:44            2365247: m=audio 18760 RTP/AVP 18 0 100 101
    2014-05-06 09:00:44            2365248: c=IN IP4 12.17.223.243
    2014-05-06 09:00:44            2365249: a=rtpmap:18 G729/8000
    2014-05-06 09:00:44            2365250: a=fmtp:18 annexb=no
    2014-05-06 09:00:44            2365251: a=rtpmap:0 PCMU/8000
    2014-05-06 09:00:44            2365252: a=rtpmap:100 X-NSE/8000
    2014-05-06 09:00:44            2365253: a=fmtp:100 192-194
    2014-05-06 09:00:44            2365254: a=rtpmap:101 telephone-event/8000
    2014-05-06 09:00:44            2365255: a=fmtp:101 0-15
    2014-05-06 09:00:45            2365256: 5820426: May  6 09:00:45.147: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    2014-05-06 09:00:45            2365257: Received:
    And then I don't see a response then send out a bye:
    Sent:
    2014-05-06 09:00:46            2365897: BYE sip:12.194.190.26:5060;transport=udp SIP/2.0
    2014-05-06 09:00:46            2365898: Via: SIP/2.0/UDP 12.17.223.243:5060;branch=z9hG4bK2D69A54BC
    2014-05-06 09:00:46            2365899: From: "Marcos Vazquez" <sip:[email protected]>;tag=5EBA1628-22FC
    2014-05-06 09:00:46            2365900: To: <sip:[email protected]>;tag=8088820710430052_c2b05.1.1.1385369448756.0_9843675_19511361
    2014-05-06 09:00:46            2365901: Date: Tue, 06 May 2014 15:00:44 GMT
    2014-05-06 09:00:46            2365902: Call-ID: [email protected]
    2014-05-06 09:00:46            2365903: User-Agent: Cisco-SIPGateway/IOS-15.2.4.M1
    2014-05-06 09:00:46            2365904: Max-Forwards: 70
    2014-05-06 09:00:46            2365905: P-Asserted-Identity: "Marcos Vazquez" <sip:[email protected]>
    2014-05-06 09:00:46            2365906: Timestamp: 1399388446
    2014-05-06 09:00:46            2365907: CSeq: 106 BYE
    2014-05-06 09:00:46            2365908: Reason: Q.850;cause=86
    2014-05-06 09:00:46            2365909: P-RTP-Stat: PS=180295,OS=3604444,PR=180354,OR=3607080,PL=0,JI=0,LA=0,DU=3603
    2014-05-06 09:00:46            2365910: Content-Length: 0
    2014-05-06 09:00:46            2365911:
    2014-05-06 09:00:46            2365912: 5820458: May  6 09:00:46.479: //3024942/CC044C80000B/SIP/Msg/ccsipDisplayMsg:
    2014-05-06 09:00:46            2365913: Sent:
    2014-05-06 09:00:46            2365914: BYE sip:[email protected]:5060;transport=tcp SIP/2.0
    2014-05-06 09:00:46            2365915: Via: SIP/2.0/TCP 10.38.246.166:5060;branch=z9hG4bK2D69A6E75
    2014-05-06 09:00:46            2365916: From: <sip:[email protected]>;tag=5EBA2282-19C8
    2014-05-06 09:00:46            2365917: To: "Marcos Vazquez" <sip:[email protected]>;tag=3831180~dfbf10b3-6c69-4443-852f-cbf609935a6f-35009402
    2014-05-06 09:00:46            2365918: Date: Tue, 06 May 2014 15:00:42 GMT
    2014-05-06 09:00:46            2365919: Call-ID: [email protected]
    2014-05-06 09:00:46            2365920: User-Agent: Cisco-SIPGateway/IOS-15.2.4.M1
    2014-05-06 09:00:46            2365921: Max-Forwards: 70
    2014-05-06 09:00:46            2365922: Timestamp: 1399388446
    2014-05-06 09:00:46            2365923: CSeq: 101 BYE
    2014-05-06 09:00:46            2365924: Reason: Q.850;cause=102
    2014-05-06 09:00:46            2365925: P-R
    2014-05-06 09:00:46            2365926: TP-Stat: PS=180239,OS=3604780,PR=180295,OR=3604444,PL=0,JI=0,LA=0,DU=3603
    2014-05-06 09:00:46            2365927: Content-Length: 0
    2014-05-06 09:00:46            2365928:

Maybe you are looking for

  • Exchange Emails Not Showing Up On IPhone with Outlook Client Closed

    I have been trying to fix this problem and I want to see if anybody else has run across this issue and found the fix. I am having a problem accessing Exchange Emails from my work system, but only under the following scenario: 1) When my work PC is po

  • How to recover a TM backup from a NAS drive

    I am using a MBPro from 2011. I lost a lot of family pictures due to my iPhoto library loosing the connection to the original hi-res files. At the moment I try to recover those with Data Rescue4 but it looks I lost quite a lot. Now, I do have the fol

  • Query taking long time To Fectch the Results

    Hi! when I run the query,it takes too long time for fetching the resultsets. Please find the query below for the same. SELECT A.BUSINESS_UNIT, A.JOURNAL_ID, TO_CHAR(A.JOURNAL_DATE,'YYYY-MM-DD'), A.UNPOST_SEQ, A.FISCAL_YEAR, A.ACCOUNTING_PERIOD, A.JRN

  • Application error- can't open itune

    Every time when I open itunes, it always shows as follows, iTunes.exe-Application Error: The exception Privileged instruction, (0xc0000096) occurred in the application at l0cation 0x013ec36a. Click on OK to terminate the program Click on CANCEL to de

  • Best choice to code an equation

    Good day everyone. I was wondering which option would be the best to code this equation I have 3 choices 1)Mathscript thought I dont want to use that since it is terribly slow (Lv 8.0.1) 2)Formula node 3)Native Lv language (with the wires ) I was thi